Structural characterization of thin hydroxypropylcellulose films. X-ray reflectivity studies

Thin solid films of hydroxypropylcellulose (HPC) have been investigated using synchrotron X-ray reflectivity. Evidence of preferential alignment of HPC molecules at the substrate surface is obtained. In the surface region the liquid crystalline domains ofHPC are preferentially oriented parallel to the substrate, whereas in the bulk they are mostly distributed randomly. Incorporation of colloidal particles in the film-substrate region destroys the preferential alignment. It is also found that in conditions of restricted geometry (very thin films), a minimum film thickness is required to produce lateral packing order perpendicular to the substrate surface.     

Molecular and Supramolecular Deformations and Disclinations in a Liquid Crystalline Copolyether Thin Films under an Electrostatic Field

An alignment study of a liquid crystalline copolyether TPP‐7/11(5/5) thin films has been carried out in a 10 kV·cm^–1 electrostatic field parallel to the thin film surface normal. This copolyether possesses a negative dielectric anisotropy. The chain molecules are homogeneously aligned in the electric field and they form two‐dimensionally ordered lamellae in a tilted columnar phase when the samples were cooled to room temperature. It is observed that the chain molecules are splayed to form bent lamellae and the chain direction is perpendicular to the tangential direction of the lamellar surfaces. These lamellae thus become replicas of the chain orientation. Due to the flexoelectric effect and density fluctuation on the thin film free surface, disclinations having topological strength s = 1, c = π/4 and defect walls form. These s = 1 disclinations possesses both left‐ and right‐handednesses. Discussion of the defect formations have been attempted.     

Lamellar orientation in thin films of symmetric semicrytalline polystyrene-b-poly(ethylene-co-butene) block copolymers: effects of molar mass, temperature of solvent evaporation, and annealing

Orientation of the lamellar microdomains in thin films of three symmetric polystyrene-b-poly(ethylene-co-butylene) block copolymers (S65E155, S156E358, and S199E452) on mica was investigated via atomic force microscopy (AFM), grazing incidence X-ray diffraction (GIXRD) and X-ray photoelectron spectroscopy (XPS). The results show that lamellar orientation in the SxEy block copolymers greatly depends on the molar mass of the block copolymers, the temperature of solvent evaporation, and annealing. The nascent thin film of the low molar mass block copolymer, S65E155, shows a multilayered structure parallel to the mica surface with the PS block at both polymer/mica and polymer/air interfaces, but the high molar mass block copolymers, S156E358 and S199E452, exhibit a structure with lamellar microdomains perpendicular to the mica surface. When the solvent is evaporated at a lower temperature, the crystallization rate is fast and a two-dimensional spherulite structure with the lamellar microdomains perpendicular to the mica surface is observed. Annealing of all the thin films with lamellar microdomains perpendicular to the mica surface leads to morphological transformation into a multilayered structure parallel to the mica surface. In all SxEy thin films on mica, the stems of PE crystals are always perpendicular to the interface between the lamellar PE and PS microdomains. A mechanism is proposed for the formation of different microdomain orientations in the thin films of semicrystalline block copolymers. When the thin film is prepared from a homogeneous solution, microdomains perpendicular to the substrate surface are formed rapidly for strongly segregated block copolymers or at a lower crystallization temperature and kinetically trapped by the strong segregation strength or solidification of crystallization, while for weakly segregated block copolymers or at slower crystallization rate, the orientation of the microdomains is dominated by surface selectivity.     

On sub-T(g) dewetting of nanoconfined liquids and autophobic dewetting of crystallites

The glass transition temperature (T(g)) of thin films is reduced by nanoconfinement, but it is also influenced by the free surface and substrate interface. To gain more insights into their contributions, dewetting behaviors of n-pentane, 3-methylpentane, and toluene films are investigated on various substrates as functions of temperature and film thickness. It is found that monolayers of these molecules exhibit sub-T(g) dewetting on a perfluoro-alkyl modified Ni substrate, which is attributable to the evolution of a 2D liquid. The onset temperature of dewetting increases with film thickness because fluidity evolves via cooperative motion of many molecules; sub-T(g) dewetting is observed for films thinner than 5 monolayers. In contrast, monolayers wet substrates of graphite, silicon, and amorphous solid water until crystallization occurs. The crystallites exhibit autophobic dewetting on the substrate covered with a wetting monolayer. The presence of premelting layers is inferred from the fact that n-pentane crystallites disappear on amorphous solid water via intermixing. Thus, the properties of quasiliquid formed on the crystallite surface differ significantly from those of the 2D liquid formed before crystallization.     

聚(ε-己内酯)薄膜结晶形貌及分子取向研究

用匀胶机通过溶液铸膜方法在硅片和铝箔基板上分别制备具有不同厚度的聚(ε-己内酯)(PCL)薄膜. 通过原子力显微镜(AFM)和偏光衰减全反射傅里叶红外光谱(ATR-FTIR)对薄膜中PCL的结晶形貌、 片晶生长方式及分子链取向进行了研究. AFM结果表明, 在200 nm或更厚的薄膜中, PCL主要以侧立(edge-on)片晶的方式生长; 对于厚度小于200 nm的薄膜, PCL片晶更倾向于以平躺(flat-on)的方式生长. 这种片晶生长方式的改变在硅片和铝箔基板上都表现出同样的倾向. 此外, 在15 nm或更薄的薄膜中, PCL结晶由通常的球晶结构变为树枝状晶体. 偏光ATR-FTIR结果表明, 当膜厚小于200 nm时, 薄膜结晶中PCL分子链沿垂直于基板表面方向取向, 并且膜越薄, 取向程度越高, 与AFM的观测结果一致.     

Deposition and crystallization studies of thin amorphous solid water films on Ru(0001) and on CO-precovered Ru(0001)

The deposition and the isothermal crystallization kinetics of thin amorphous solid water (ASW) films on both Ru(0001) and CO-precovered Ru(0001) have been investigated in real time by simultaneously employing helium atom scattering, infrared reflection absorption spectroscopy, and isothermal temperature-programmed desorption. During ASW deposition, the interaction between water and the substrate depends critically on the amount of preadsorbed CO. However, the mechanism and kinetics of the crystallization of approximately 50 layers thick ASW film were found to be independent of the amount of preadsorbed CO. We demonstrate that crystallization occurs through random nucleation events in the bulk of the material, followed by homogeneous growth, for solid water on both substrates. The morphological change involving the formation of three-dimensional grains of crystalline ice results in the exposure of the water monolayer just above the substrate to the vacuum during the crystallization process on both substrates.     

左旋聚乳酸/聚(ε-己内酯)共混物在取向聚乙烯基底上的附生结晶行为

利用电子显微镜结合电子衍射研究了左旋聚乳酸/聚(ε-己内酯)(PLLA/PCL)共混物在取向聚乙烯(PE)基底上的结晶行为.纯PLLA在取向PE基底上能够附生结晶,主要形成分子链相互垂直的片晶结构.PCL在PE基质上也能发生附生结晶,导致两者分子链平行.PLLA/PCL共混物在取向PE基底上结晶的形态结构依赖于共混组成.在PLLA含量大于95 wt%时,PCL不影响PLLA与PE的附生结晶行为.当PCL含量增加至10 wt%时,PLLA在PE上的附生结晶行为受到了一定程度的影响.当PCL含量超过40 wt%时,PLLA在PE上的附生结晶被抑制,取而代之是PCL在PE取向基质上附生结晶,产生两者分子链平行的取向片晶.另外,在PLLA含量在50 wt%~30 wt%之间时,体系产生明显的微相分离,微相分离并不影响PCL与PE的附生结晶,在PCL的富集区仍然发生平行链附生结晶,而PLLA的富集区结构变得模糊.当PLLA含量少于20 wt%时,微相分离不明显,少量PLLA应该分散在PCL片晶间的非晶区.     

THE CRYSTALLIZATION BEHAVIOR OF URETHANE SUBSTITUTED POLYDIACETYLENE

The crystalline behavior of urethane substitute polydiacetylene was studied by using pohrized light and electron microscopy. The lamellar morphological structure was observed in the crystallized films. The thickness of lamellae is about 300A, being independent of the crystalline temperature. But the size and density of lamellae were dependent on the crystallization temperature. If the molten film was sheared during the crystallzation process the oriented lamellae grew with their long axes perpendicular to the direction of shear and the chain direction was normal to the lamellar surface.     

聚苯乙烯/聚二甲基硅氧烷嵌段共聚物的表面形态研究

采用原子力显微镜(AFM)和透射电镜(TEM)研究了聚苯乙烯/聚二甲基硅氧烷嵌段共聚物(PS-b-PDMS)薄膜的相形态.结果表明,当采用甲苯作为溶剂,旋转涂膜的薄膜样品呈现网络状的形态分布在表面,而样品所对应的透射电镜照片中,PDMS相作为球状分布在PS的连续相中.退火温度对共聚物表面形态有一定的影响,当退火温度高于PDMS的玻璃化温度,表面中PDMS相增多.PS-b-PDMS嵌段共聚物的表面形态随着所用溶剂的变化而有所不同,当采用甲苯作为溶剂时,样品的PS相形成凹坑分布在PDMS的相区之中,而采用环己烷作为溶剂时,PS相作为突起分布在PDMS相区之中.另外,基底对共聚物薄膜表面形态的有较大的影响,当采用硅晶片作为基底时,样品中的PDMS相和PS相呈现近似平行于表面的层状结构.     

Diblock copolymer lamellae on sinusoidal and fractal surfaces

A scaling analysis of equilibrium orientation of diblock copolymer molecules on fractal surfaces and a brief comparison with a particular experiment is presented in this paper. This work is motivated by a recent experimental finding that a diblock copolymer film of polystyrene-PMMA, when deposited on a rough substrate, can orient its lamellae from a parallel to a perpendicular configuration depending on the topographical characteristics of the substrate surface. It was found that the RMS height itself is not enough to effect the equilibrium configuration, but the fractal dimension of the surface is also important. In general, the orientation of lamellae is a function of the the power spectral density (PSD) curves of the underlying substrate surface. Assuming the diblock lamellae to behave like an Alexander-deGennes brush, we obtain the free energy expressions for this brush in both parallel and perpendicular orientations in various asymptotic regimes. Comparison of their free energy expressions predicts the equilibrium configuration. By examining the PSD curves and using our scaling results, we are able to qualitatively explain some aspects of the experimental observations regarding the equilibrium orientation of the diblock copolymer lamellae on rough surfaces.     

聚3-羟基丁酸酯薄膜结晶的ATR-FTIR研究

使用匀胶机(spincoater),通过溶液铸膜的方法,在铝箔基板上制备出具有不同厚度的聚3羟基丁酸酯(PHB)薄膜.20℃室温条件下,通过衰减全反射傅立叶红外光谱(ATRFTIR)原位观测了不同厚度薄膜的结晶过程,并通过偏光ATRFTIR对薄膜中PHB分子的取向进行了研究.ATRFTIR原位观测结果显示,PHB在薄膜中的结晶速率以及结晶度均随着薄膜厚度的减小而逐渐降低;同时,偏光ATRFTIR测试结果表明,随膜厚减小,薄膜中结晶部分的PHB分子逐渐倾向于沿垂直于基板表面方向取向,膜越薄,倾向越明显.可以认为,PHB分子与基板间的相互作用以及扩散控制结晶导致了上述现象的产生.     

AFM研究PCL薄膜的结晶形态

利用原子力显微镜 (AFM)详细研究了聚己内酯 (PCL)超薄膜及其在特殊限制环境下的结晶形态 .AFM的观察表明 ,PCL在石英基板上的结晶形态呈现典型的球晶及比较少见的树枝状晶两种形态 .认为主要是超薄膜结晶过程中由于几何受限及基板吸附导致分子链扩散移动速度大大降低 ,由此形成的扩散控制结晶过程从而导致最终形成树枝状的分形结构 .将聚合物限制在间距为 10 μm的凹槽内 ,发现PCL的结晶有比较规整的排列 ,而且沿着凹槽的方向结晶排列取向优先 .当在凹槽两侧铝条上施加强电场后 ,发现在静电场作用下 ,PCL的结晶取向生长方向发生改变 ,沿着电场方向排列生长的结晶增多     

Epitaxial crystallization of isotactic poly(methyl methacrylate) on highly oriented polyethylene

The annealing behavior of amorphous i-PMMA thin films on highly oriented HDPE substrates was studied by transmission infrared spectroscopy and electron diffraction. The i-PMMA thin film on highly oriented HDPE exhibits a much faster crystallization rate than usual, providing not only a good method for the preparation of crystalline i-PMMA thin and ultrathin film, but also the convenience to observe the crystallization process by infrared spectroscopy in situ. The overall crystallization kinetics of the i-PMMA thin film on the highly oriented HDPE layer was also explored in this work, and an Avrami exponent of about 2 was obtained. The accelerated crystallization behavior indicates a special interaction between HDPE and i-PMMA, which favors the nucleation and crystallization of i-PMMA. This special interaction leads also to an oriented alignment of i-PMMA on the HDPE substrate with both polymer chains parallel, i.e., the occurrence of heteroepitaxy, which could be verified by the polarized infrared spectra and electron diffraction pattern. Electron diffraction analysis further demonstrated that the contact planes of this epitaxial system are (100) lattice planes of both polymers. This can be explained in terms of a two-dimensional lattice matching.     

Thickness-dependent molecular chain and lamellar crystal orientation in ultrathin poly(di-n-hexylsilane) films

The molecular chain and lamellar crystal orientation in ultrathin films (thickness < 100 nm) of poly-(di-n-hexylsilane) (PDHS) on silicon wafer substrates have been investigated by using transmission electronic microscopy, wide-angle X-ray diffraction, atomic force microscopy, and UV absorption spectroscopy. PDHS showed a film thickness-dependent molecular chain and lamellar crystal orientation. Lamellar crystals grew preferentially in flat-on orientation in the monolayer ultrathin films of PDHS, i.e., the silicon backbones were oriented along the surface-normal direction. By contrast, the orientation of lamellar crystals was preferentially edge-on in ultrathin films thicker than ca. 13 nm, i.e., the silicon backbones were oriented parallel to the substrate surface. We interpret the different orientations of molecular chain and lamellar crystal as due to the reduction of the entropy of the polymer chain near the substrate surface and the particularity of the crystallographic (001) plane of flat-on lamellae, respectively. A remarkable influence of the orientations of the silicon backbone on the UV absorption of these PDHS ultrathin films was observed due to the one-dimensional nature of sigma-electrons delocalized along the silicon backbone. With the silicon backbones perpendicular or parallel to the surface of the substrate, the UV absorbance increased or decreased with an increase of the angle between the incident UV beam direction and direction normal to the thin film, respectively.     

Orientation control of ferroelectric polymer molecules using contact-mode AFM

We have developed an orientation control technique for polymer molecules utilizing contact-mode atomic force microscopy (AFM). In this technique, the molecular chains were directly modified by scanning an AFM cantilever tip in contact with the film surface at the temperature just below its melting point. We call this process “modification scan”. Here, we applied this technique to poly(vinylidenefluoride-trifluoroethylene) (P(VDF-TrFE)) thin films on graphite and glass. We prepared a 75-nm thick copolymer crystalline film on graphite whose lamellar plane was perpendicular to the substrate (edge-on), and also prepared a film of the same thickness on glass whose lamellar plane was parallel to the substrate (flat-on). After applying this technique on both films, molecular chains were stretched and aligned to the modification scan direction, and new edge-on crystals were obtained, whose lamellar planes were well-aligned perpendicular to the modification scan direction.     

Crystallographic and morphological characterization of thin pentacene films on polycrystalline copper surfaces

The degree of crystallinity, the structure and orientation of crystallites, and the morphology of thin pentacene films grown by vapor deposition in an ultrahigh vacuum environment on polycrystalline copper substrates have been investigated by x-ray diffraction and tapping-mode scanning force microscopy (TM-SFM). Depending on the substrate temperature during deposition, very different results are obtained: While at 77 K a long-range order is missing, the films become crystalline at elevated temperatures. From a high-resolution x-ray-diffraction profile analysis, the volume-weighted size of the crystallites perpendicular to the film surface could be determined. This size of the crystallites increases strongly upon changing temperature between room temperature and 333 K, at which point the size of individual crystallites typically exceeds 100 nm. In this temperature region, three different polymorphs are identified. The vast majority of crystallites have a fiber texture with the (001) net planes parallel to the substrate. In this geometry, the molecules are oriented standing up on the substrate (end-on arrangement). This alignment is remarkably different from that on single-crystalline metal surfaces, indicating that the growth is not epitaxial. Additionally, TM-SFM images show needlelike structures which suggest the presence of at least one additional orientation of crystallites (flat-on or edge-on). These results indicate that properties of thin crystalline pentacene films prepared on technologically relevant polycrystalline metal substrates for fast electronic applications may be compromised by the simultaneous presence of different local molecular aggregation states at all temperatures.     

Self-assembly of ABC star triblock copolymer thin films confined with a preferential surface: a self-consistent mean field theory

The microphase separation and morphology of a nearly symmetric A(0.3)B(0.3)C(0.4) star triblock copolymer thin film confined between two parallel, homogeneous hard walls have been investigated by self-consistent mean field theory (SCMFT) with a pseudospectral method. Our simulation experiments reveal that under surface confinement, in addition to the typically parallel, perpendicular, and tilted cylinders, other phases such as lamellae, perforated lamellae, and complex hybrid phases have been found to be stable, which is attributed to block-substrate interactions, especially for those hybrid phases in which A and B blocks disperse as spheres and alternately arrange as cubic CsCl structures, with a network preferred structure of C block. The results show that these hybrid phases are also stable within a broad hybrid region (H region) under a suitable film thickness and a broad field strength of substrates because their free energies are too similar to being distinguished. Phase diagrams have been evaluated by purposefully and systematically varying the film thickness and field strength for three different cases of Flory-Huggins interaction parameters between species in the star polymer. We also compare the phase diagrams for weak and strong preferential substrates, each with a couple of opposite quality, and discuss the influence of confinement, substrate preference, and the nature of the star polymer on the stability of relatively thinner and thick film phases in this work.     

Influence of substrate nature and growth conditions on the morphology of thin DMOAP films

We report some preliminary results on the morphology of thin N,N -dimethyl- n -octadecyl-3-aminopropyltrimethoxysilyl chloride (DMOAP) films. When deposited on a glass substrate, DMOAP forms a mono- or multi-layer structure parallel to the substrate. The surface topography of the film is probed by atomic force microscopy. In general, the free surface of such a film is not flat and smooth. Islands and holes are formed on the free surface of the films when a sufficiently flat substrate is used. The thin film surface topography depends strongly on the nature of the bare substrate, the curing conditions, and the immersion time of the substrate in the DMOAP solution. The film is always rougher than the bare substrate used. Annealing roughens the surface of the alkoxysilane thin films deposited on a glass substrate. For films on glass plates covered with an indium tin oxide layer, annealing has minor effects. The surface topography affects the microstructure of homeotropic smectic samples.     

Structure of thin block copolymer films studied by X-ray reflectivity

Summary X-ray reflectivity may be used to determine the internal structure of thin polymer films. An electron density difference of 10% for polystyrene and polyisoprene is sufficient to distinguish between a random distribution of lamellae, complete orientation parallel to the substrate surface and a surface induced formation of lamellae. The disappearance of the lamellar Bragg-peaks, with heating of the film, shows the transition into the disordered state.     

WHAT ARE THE DIFFERENCES OF POLYMER SURFACE RELAXATION FROM THE BULK?

The polymer surface relaxation in thin films has been a long debating issue.We report a new method on studying surface relaxation behaviors of polymer thin films on a solid substrate.This method involved utilizing a rubbed polyimide surface with a pretilting angle in a liquid crystalline cell.Due to the surface alignment,the liquid crystals were aligned along the rubbing direction.During heating the liquid crystalline cell,we continuously monitored the change of orientation of the liquid crystals.It is u...