Determination of pharmaceuticals in biosolids using accelerated solvent extraction and liquid chromatography/tandem mass spectrometry

An analytical method was developed to quantitatively determine pharmaceuticals in biosolid (treated sewage sludge) from wastewater treatment plants (WWTPs). The collected biosolid samples were initially freeze dried, and grounded to obtain relatively homogenized powders. Pharmaceuticals were extracted using accelerated solvent extraction (ASE) under the optimized conditions. The optimal operation parameters, including extraction solvent, temperature, pressure, extraction time and cycles, were identified to be acetonitrile/water mixture (v/v 7:3) as extraction solvent with 3 extraction cycles (15 min for each cycle) at 100 °C and 100 bars. The extracts were cleaned up using solid-phase extraction followed by determination by liquid chromatography coupled with tandem mass spectrometry. For the 15 target pharmaceuticals commonly found in the environment, the overall method recoveries ranged from 49% to 68% for tetracyclines, 64% to 95% for sulfonamides, and 77% to 88% for other pharmaceuticals (i.e. acetaminophen, caffeine, carbamazepine, erythromycin, lincomycin and tylosin). The developed method was successfully validated and applied to the biosolid samples collected from WWTPs located in six cities in Michigan. Among the 15 target pharmaceuticals, 14 pharmaceuticals were detected in the collected biosolid samples. The average concentrations ranged from 2.6 μg/kg for lincomycin to 743.6 μg/kg for oxytetracycline. These results indicated that pharmaceuticals could survive wastewater treatment processes, and accumulate in sewage sludge and biosolids. Subsequent land application of the contaminated biosolids could lead to the dissemination of pharmaceuticals in soil and water environment, which poses potential threats to at-risk populations in the receiving ecosystems.     

Determination of commonly used azole antifungals in various waters and sewage sludge using ultra-high performance liquid chromatography–tandem mass spectrometry

Sensitive and reliable methods have been developed and validated for determination of commonly consumed azole antifungal pharmaceuticals (clotrimazole, econazole, ketoconazole, and miconazole) and biocides (propiconazole and tebuconazole) in various waters and sewage sludge. Solid phase extraction (SPE) combined with ultra-high performance liquid chromatography–tandem mass spectrometry (UHPLC–MS/MS) was used to determine the azole antifungals in waters. Azole antifungals in sewage sludge were extracted with ultrasonic-assisted extraction, followed by SPE cleanup and UHPLC–MS/MS detection. Quantification was performed by internal standard calibration in multiple reaction monitoring mode. Recoveries were mostly in the range of 52–110% with relative standard deviations generally within 20%. Method quantification limits were 0.5–6 ng L⁻¹ in waters and 3–9 ng g⁻¹ dry weight (dw) in sewage sludge, respectively. The methods were applied to determine the azole antifungals in wastewater, river water, sediment, and sewage sludge sampled from the Pearl River Delta, China. Clotrimazole, ketoconazole, and miconazole were widely detected at low ng L⁻¹ in waters, low ng g⁻¹ dw in river sediment, and low μg g⁻¹ dw in sewage sludge. The methods can provide valuable tools for investigating occurrence and fate of the azole antifungals in the environment.     

Enantiomeric determination of azole antifungals in wastewater and sludge by liquid chromatography–tandem mass spectrometry

A sensitive and reliable liquid chromatographic-tandem mass spectrometric method for enantiomeric determination of five chiral azole antifungals (econazole, ketoconazole, miconazole, tebuconazole, and propiconazole) in wastewater and sludge has been established and validated. An isotope-labeled internal standard was used for quantification. Recovery of the individual enantiomers was usually in the range of 77-102 % for wastewater and 71-95 % for sludge, with relative standard deviations within 20 %. No significant difference (p>0.05) was observed between recovery of pairs of enantiomers of the chiral azole antifungals except for those of tebuconazole. Method quantification limits for individual enantiomers were 0.3-10 ng L(-1) and 3-29 ng g(-1) dry weight for wastewater and sludge, respectively. The method was used to investigate the enantiomeric composition of the azole pharmaceuticals in wastewater and sludge samples from a sewage treatment plant in China. Enantiomers of miconazole, ketoconazole, and econazole were widely detected. The results showed that the azole antifungals in wastewater and sludge were generally racemic or marginally non-racemic. The method is a useful tool for investigation of the enantiomeric occurrence, behavior, and fate of the chiral azole antifungals in the environment.     

Pressurized liquid extraction of pharmaceuticals from sewage-sludge

A method for the quantitative determination of ten pharmaceuticals in sewage sludge was developed by using pressurized liquid extraction (PLE) and HPLC-MS with ESI (HPLC-(ESI)MS). The PLE was optimized with regard to solvents and operational parameters, such as temperature, pressure, extraction time, and purge time. The optimum conditions were: 50 mM phosphoric acid/methanol (1:1 v/v) as the extraction solvent, temperature of 100 degrees C, pressure of 100 bar, extraction time 15 min, 2 cycles, flush volume 150% and purge time 300 s. All recoveries for pharmaceuticals were over 68% except for salicylic acid. The repetitivity and reproducibility between days expressed as RSD was lower than 8% for repetitivity and 10% for reproducibility. The LOD of all compounds was lower than 10 microg/kg of dry weight of sewage sludge. The method was applied to determine the pharmaceuticals in sewage sludge from two domestic sewage treatment plants (STPs). The samples were collected every three months between February 2004 and June 2005. Some pharmaceuticals were determined in the samples and naproxen showed the highest value (242 microg/kg of dry weight).     

Determination of hexabromocyclododecane isomers in sewage sludge by LC‐MS/MS

A method has been developed to determine α, β and γ diastereoisomers of hexabromocyclododecane (HBCD), a brominated flame retardant, in sewage sludge, based on the ultrasonic‐assisted extraction (UAE) of samples with dichloromethane–ACN (1:1) and the subsequent clean‐up of extracts by dispersive solid phase extraction with primary–secondary amine. Levels of HBCD diastereoisomers were determined by LC coupled with ESI MS/MS. Evaluation of the matrix effect showed a high ion suppression for all the diastereoisomers studied, which was counteracted by using a mixture of labelled HBCD diastereoisomers as internal standards. This method yielded recoveries in the range of 79.6–112.5% with SDs equal or lower than 9.1 The limits of detection were 0.3 ng/g for α‐ and β‐HBCD and 0.2 ng/g for γ‐HBCD. The developed method was successfully applied to 19 sludge samples collected from the province of Madrid (Spain). In most of the samples, β‐HBCD was below the method detection limit, whereas α‐ and γ‐HBCD were quantified in all of the sludge samples, and γ‐HBCD was the predominant diastereoisomer in 63% of the analyzed samples and α‐HBCD predominated in the rest.     

Determination of pharmaceuticals from various therapeutic classes in dewatered sludge by pressurized liquid extraction and high performance liquid chromatography and tandem mass spectrometry (HPLC-MS/MS)

Pharmaceuticals are released to the environment after human and animal consumption, which partly comes from accumulation in sewage sludge during wastewater treatment. This paper developed a method for the determination of N,N-diethyl-meta-toluamide (DEET) and 14 pharmaceuticals belonging to multiple therapeutic classes such as antibiotic, anti-inflammatory, antilipidemic, anti-hypertensive, and anticonvulsant in dewatered sludge. Pressurized liquid extraction using methanol/McIlvaine buffer (volume ratio, 1?:?1), associated with HPLC-MS/MS was proven to be effective for extraction and quantification of pharmaceuticals and DEET in dewatered sludge. Optimization procedures, including extraction method, extraction solvents and clean-up treatment, were carried out by simulating naturally aged samples to provide a more realistic extraction than previous methods, which were often done by spiking the standard solution before extraction without any aging procedures. The internal standard quantification method using six isotopically labelled compounds was applied to improve the poor absolute recoveries induced by severe matrix effects to obtain better relative recoveries (70–120%). Good relative standard deviations (lower than 19.0% for 7 repeats) and the limit of quantification (0.6–19.4?µg/kg) indicated that the developed method was reliable and sensitive to extract and quantify the studied pharmaceuticals in dewatered sludge. For samples collected from eight sewage treatment plants in Beijing, China, it was found that trimethoprim, caffeine, ketoprofen and ibuprofen were the most prominent contaminants, with the median concentrations reaching 97.6, 179.4, 268.0 and 153.0?µg/kg, respectively. The level of ketoprofen, ibuprofen, mefenamic acid, cabamazepine and diclofenac were similar to results reported from Spain, whilst the levels of other compounds were similar to those found in Germany, Canada and the US.     

Automated on-fiber derivatization with headspace SPME-GC-MS-MS for the determination of primary amines in sewage sludge using pressurized hot water extraction

An automated, environmentally friendly, simple, selective, and sensitive method was developed for the determination of ten primary aliphatic amines in sewage sludge at μg/kg dry weight (d.w.). The procedure involves a pressurized hot water extraction (PHWE) of the analytes from the solid matrix, followed by a fully automated on‐fiber derivatization with 2,3,4,5‐pentafluorobenzaldehyde (PFBAY) and headspace solid‐phase microextraction (HS‐SPME) and subsequent gas chromatography ion‐trap tandem mass spectrometry (GC‐IT‐MS‐MS) analysis. The limits of detection (LODs) of the method were between 0.5 and 45 μg/kg (d.w.) for all compounds except for ethyl‐, isopropyl‐, and amylamine, whose LODs were 70, 109, and 116 μg/kg (d.w.), respectively. The limits of quantification (LOQs) were between 10 and 350 μg/kg (d.w.). Repeatability and intermediate precision, expressed as RSD(%) (n=3), were lower than 18 and 21%, respectively. The method developed enabled to determine primary aliphatic amines in sludge from various urban and industrial sewage treatment plants as well as from a potable treatment plant. Most of the primary aliphatic amines were found in the sewage sludge samples analyzed corresponding to the maximum concentrations to the samples from the urban plant: for instance, isobutylamine and methylamine were found at 7728 and 12 536 μg/kg (d.w.), respectively. Amylamine was detected only in few samples but always at concentrations lower than its LOQ.     

Pharmaceutical determination in surface and wastewaters using high-performance liquid chromatography-(electrospray)-mass spectrometry

A method was developed to determine 11 pharmaceutical compounds in water samples. The method uses SPE and HPLC coupled to MS (LC/MS) using ESI in both positive and negative modes. Three different sorbents were compared for the extraction of analytes from river and sewage treatment plant (STP) waters and OASIS HLB provided the best results. For the solid-phase extraction of 500 mL of river water samples, the recoveries were between 41 and 101% with the exception of acetaminophen, salicylic acid and naproxen. The LODs were between 3 and 5 ng/L for all the compounds, except naproxen which had an LOD of 15 ng/L. Acetaminophen, caffeine, carbamazepine, bezafibrate and ibuprofen were found in three of the tested river samples at ng/L levels and among them, the highest values were for caffeine and bezafibrate with 305 and 363 ng/L, respectively. For the influent and effluent water samples of the STP, volumes of 100 and 250 mL were used, respectively, to obtain acceptable recoveries. All the compounds showed recoveries between 33 and 91% for effluent samples and 33-72% for influent samples, with the exception of acetaminophen, salicylic acid and bezafibrate, which had lower recoveries. The method developed enabled pharmaceuticals in the influent and effluent sewage waters to be determined in five campaigns carried out between February 2004 and June 2005. Several pharmaceuticals were found in the influent samples: for instance, maximum concentrations of ibuprofen and caffeine were 6 and 40 microg/L, respectively.     

Determination of musk fragrances in sewage sludge by pressurized liquid extraction coupled to automated ionic liquid‐based headspace single‐drop microextraction followed by GC‐MS/MS

A method for the quantitative determination of ten musk fragrances extensively used in personal care products from sewage sludge was developed by using a pressurized liquid extraction (PLE) followed by an automated ionic liquid‐based headspace single‐drop microextraction and gas chromatography‐tandem mass spectrometry. The influence of main factors on the efficiency of PLE was studied. For all musks, the highest recovery values were achieved using 1 g of pretreated sewage sludge, H₂O/methanol (1:1) as an extraction solvent, a temperature of 80°C, a pressure of 1500 psi, an extraction time of 5 min, 2 cycles, a 100% flush volume, a purge time of 120 s, and 1 g Florisil as in‐cell clean‐up extraction sorbent. The use and optimization of an in‐cell clean‐up sorbent was necessary to remove fatty interferents of the PLE extract that make the subsequent ionic liquid‐based headspace single‐drop microextraction difficult. Validation parameters, namely LODs and LOQs, ranged from 0.5–1.5 to 2.5–5 ng/g, respectively. Good levels of intra‐ and interday repeatabilities were obtained analyzing sewage sludge samples spiked at 10 ng/g (n = 3, RSDs < 10%). The method applicability was tested with sewage sludge from different wastewater treatment plants. The analysis revealed the presence of all the polycyclic musks studied at concentrations higher than the LOQs, ranging from 6 to 530 ng/g. However, the nitro musk concentrations were below the LOQs or, in the case of musk xylene, was not detected.     

Determination of pharmaceuticals,steroid hormones,and endocrine-disrupting personal care products in sewage sludge by ultra-high-performance liquid chromatography–tandem mass spectrometry

A sensitive method has been developed and validated for the determination of diverse groups of pharmaceuticals, steroid hormones, and hormone-like personal care products in sewage sludge. Samples were extracted by ultrasonic-assisted extraction followed by solid-phase extraction cleanup. For determination of estrogens and hormone-like phenolic compounds, sample extracts were further derivatized with dansyl chloride and purified with silica gel column chromatography to improve the analytical sensitivity. The chemicals were determined by ultra-high-performance liquid chromatography–tandem mass spectrometry (UHPLC-MS/MS) in multiple-reaction monitoring mode. Recoveries ranged mostly from 63% to 119% with relative standard deviations within 15%. Method quantification limits were 0.1–3 ng g⁻¹ dry weight (dw) for sewage sludge. The method was applied to a preliminary investigation of pharmaceuticals and personal care products (PPCPs) in sewage sludge and sediment in the Pearl River Delta, South China. Triclosan, triclocarban, 2-phenylphenol, bisphenol A, and parabens were ubiquitously detected at 3.6–5088.2 ng g⁻¹ dw in sludge and 0.29–113.1 ng g⁻¹ dw in sediment samples, respectively. Estrone, carbamazepine, metoprolol, and propranolol were also frequently quantified in the sludge and sediment samples. The dewatering process caused no significant losses of these PPCPs in sewage sludge.     

A multiresidue analytical method using solid-phase extraction and high-pressure liquid chromatography tandem mass spectrometry to measure pharmaceuticals of different therapeutic classes in urban wastewaters

An analytical method with two extraction steps has been developed and validated for the simultaneous determination of 30 pharmaceuticals belonging to various therapeutic categories in urban wastewater. The aim was to boost the little available information on drugs' fates in sewage treatment plants (STPs) and in the receiving surface water. Aqueous samples were divided into two aliquots, each extracted by a different solid-phase extraction (SPE) method and analysed by reversed-phase liquid chromatography tandem mass spectrometry (HPLC-MS-MS). Recoveries of the pharmaceuticals were mostly greater than 70% and the overall variability of the method was below 8%. The instrumental quantification limit (IQL) varied between 30 and 400 pg injected, and the limits of quantification (LOQ) were in the low ng/L range. Nineteen pharmaceuticals were detected in concentrations between 0.5 and 2000 ng/L in effluents collected from several STPs in Italy. Atenolol, ciprofloxacin, furosemide, hydrochlorothiazide, ofloxacin, ranitidine and sulphamethoxazole were the most abundant compounds. The present analytical method was useful to check for pharmaceuticals in various Italian STPs and to identify the most abundant compounds.     

Selective extraction of sulfonamides, macrolides and other pharmaceuticals from sewage sludge by pressurized liquid extraction

A method for the quantitative determination of three macrolides, five sulfonamides, ranitidine, omeprazole and trimethoprim in sewage sludge samples was developed by using pressurized liquid extraction and high-performance liquid chromatography-electrospray ionization mass spectrometry. The extraction solvent and such operational parameters as temperature, pressure, extraction time and purge time were optimized in pressurized liquid extraction. The experimental conditions were: an extraction solvent of water (pH 3):methanol (1:1, v/v), a temperature of 80 degrees C, a pressure of 1500 psi, a sample weight of 5 g, an extraction time of 5 min, one cycle, a flush volume of 60% and a purge time of 120 s. All recoveries were over 74%, except those for ranitidine whose value was 54%. The repeatability and reproducibility between days expressed as relative standard deviation (n = 3) were lower than 11% and 15%, respectively. The limit of detection values ranged from 2 to 11 microg/kg dry weight (d.w.). The method was applied to determine the pharmaceuticals in sewage sludge from two domestic sewage treatment plants. Roxithromycin and tylosin were determined in the samples and tylosin showed the highest value (4.0 mg/kg d.w.).     

A new sample preparation method for determination of acidic drugs in sewage sludge applying microwave assisted solvent extraction followed by gas chromatography-mass spectrometry

This paper presents a new sample preparation procedure for determination of selected acidic pharmaceuticals (ibuprofen, naproxen, ketoprofen, and diclofenac) in sewage sludge using microwave assisted solvent extraction, dispersive matrix extraction (DME) followed by the conventionally applied solid phase extraction (SPE), derivatization, and gas chromatography-mass spectrometry. The recoveries calculated from analytical data of spiked sludge samples changed in the range of 80-105% ± 15% for the four pharmaceuticals in mixed and activated sludge depending on the efficiency of the clean-up procedure. The measured concentration values of ibuprofen and naproxen were identical in the mixed and the activated sludge samples. However, ketoprofen and diclofenac showed about twice as high concentration in activated sludge than in the mixed one independently of the applied extraction method. The typical concentration ranges of ibuprofen, naproxen, ketoprofen and diclofenac in sewage sludge were 10-30 ng/g, 30-50 ng/g, 50-130 ng/g, and 50-140 ng/g respectively.     

Determination of organochlorine pesticides in sewage sludge by matrix solid-phase dispersion and gas chromatography-mass spectrometry

A method based on matrix solid-phase dispersion (MSPD) has been developed for the determination of 16 organochlorine pesticides (OCs) in sludge from municipal sewage plants. Samples of lyophilized sludge were blended with alumina, placed in small columns and OCs extracted with dichloromethane assisted by sonication. Purification of the extracts was accomplished by solid-phase extraction on C₁₈ columns and OCs were eluted with acetonitrile. Analyses were performed by gas chromatography with electron impact mass spectrometric detection in the selected ion monitoring mode (GC–MS-SIM) using deuterated OCs as internal standards. The limits of detection were between 0.03 ng/g for 4,4′-DDE and 0.7 ng/g for endrin aldehyde.

Levels of OCs were determined in sewage sludge collected from 19 water treatment plants located in the province of Madrid (Spain). In all of the analyzed samples, aldrin was the compound most often found with a mean concentration of 76 ng/g. Endosulfan-I, -BHC, 4,4′-DDE and 4,4′-DDT were also present at high concentrations, with average values ranging from 32.3 to 74.3 ng/g. OCs were detected in all of the samples, with a total concentration ranging from 52 to 528 ng/g dry weight.     

Analysis of perfluorinated compounds in sewage sludge by pressurized solvent extraction followed by liquid chromatography-mass spectrometry

Perfluorinated compounds (PFCs) are widely used in everyday life and one of the main recipients of these compounds is waste water treatment plants (WWTPs). Due to the structure and physicochemical properties of PFCs, these compounds could be redistributed from influent water to sludge. This work reports a new validated protocol for the analysis of 13 perfluorinated acids, 4 perfluorosulfonates and the perfluorooctanesulfonamide. The present work has been focused to develop a sensitive and robust method for the analysis of 18 PFCs in sewage sludge, based on pressurized solvent extraction (PSE) followed by solid phase extraction (SPE) clean-up, analytes separation by liquid chromatography and analysis in a hybrid quadrupole-linear ion trap mass spectrometer (LC-QLiT-MS/MS) working in single reaction monitoring (SRM) mode. The final methodology was validated using a blank sewage sludge fortified at different concentration levels. The method limits of detection were ranging in general from 15 to 79 ng/kg. These values were comparable to the decision limit (CCα) and the detection capability (CCβ), which were 17-1134 ng/kg and 18-1347 ng/kg, respectively. The percentage of recovery was from 79 to 111% in the most cases at different spiked levels. Finally, the repeatability of the method was in the range 4% (PFOS and PFOA) to 25% (RSD %). In order to evaluate the applicability of the method, 5 sludge samples were analyzed. The results showed that the 18 PFCs were present in all samples. However, the concentrations for most of them were below the limits of quantification. The compound present at higher concentrations was perfluorooctanesulfonate (PFOS), which was in concentrations from 53.0 to 121.1 μg/kg. The other PFCs were at concentrations between 0.3 and 30.3 μg/kg.     

Determination of biocides in different environmental matrices by use of ultra-high-performance liquid chromatography–tandem mass spectrometry

A sensitive and robust method using solid-phase extraction and ultrasonic extraction for preconcentration followed by ultra-high-performance liquid chromatography–tandem mass spectrometry (UHPLC–MS–MS) has been developed for determination of 19 biocides: eight azole fungicides (climbazole, clotrimazole, ketoconazole, miconazole, fluconazole, itraconazole, thiabendazole, and carbendazim), two insect repellents (N,N-diethyl-3-methylbenzamide (DEET), and icaridin (also known as picaridin)), three isothiazolinone antifouling agents (1,2-benzisothiazolinone (BIT), 2-n-octyl-4-isothiazolinone (OIT), and 4,5-dichloro-2-n-octyl-isothiazolinone (DCOIT)), four paraben preservatives (methylparaben, ethylparaben, propylparaben, and butylparaben), and two disinfectants (triclosan and triclocarban) in surface water, wastewater, sediment, sludge, and soil. Recovery of the target compounds from surface water, influent, effluent, sediment, sludge, and soil was mostly in the range 70–120?%, with corresponding method quantification limits ranging from 0.01 to 0.31?ng?L^?1, 0.07 to 7.48?ng?L^?1, 0.01 to 3.90?ng?L^?1, 0.01 to 0.45?ng?g^?1, 0.01 to 6.37?ng?g^?1, and 0.01 to 0.73?ng?g^?1, respectively. Carbendazim, climbazole, clotrimazole, methylparaben, miconazole, triclocarban, and triclosan were detected at low ng?L^?1 (or ng?g^?1) levels in surface water, sediment, and sludge-amended soil. Fifteen target compounds were found in influent samples, at concentrations ranging between 0.4 (thiabendazole) and 372?ng?L^?1 (methylparaben). Fifteen target compounds were found in effluent samples, at concentrations ranging between 0.4 (thiabendazole) and 114?ng?L^?1 (carbendazim). Ten target compounds were found in dewatered sludge samples, at concentrations ranging between 1.1 (DEET) and 887?ng?g^?1 (triclocarban).     

Ultrasound-enhanced surfactant-assisted dispersive liquid–liquid microextraction and high-performance liquid chromatography for determination of ketoconazole and econazole nitrate in human blood

A simple and efficient method, based on ultrasound-enhanced surfactant-assisted dispersive liquid–liquid microextraction (UESA-DLLME) followed by high-performance liquid chromatography (HPLC) has been developed for extraction and determination of ketoconazole and econazole nitrate in human blood samples. In this method, a common cationic surfactant, cetyltrimethylammonium bromide (CTAB), was used as dispersant. Chloroform (40 μL) as extraction solvent was added rapidly to 5 mL blood containing 0.068 mg mL⁻¹ CTAB. The mixture was then sonicated for 2 min to disperse the organic chloroform phase. After the extraction procedure, the mixture was centrifuged to sediment the organic chloroform phase, which was collected for HPLC analysis. Several conditions, including type and volume of extraction solvent, type and concentration of the surfactant, ultrasound time, extraction temperature, pH, and ionic strength were studied and optimized. Under the optimum conditions, linear calibration curves were obtained in the ranges 4–5000 μg L⁻¹ for ketoconazole and 8–5000 μg L⁻¹ for econazole nitrate, with linear correlation coefficients for both >0.99. The limits of detection (LODs, S/N = 3) and enrichment factors (EFs) were 1.1 and 2.3 μg L⁻¹, and 129 and 140 for ketoconazole and econazole nitrate, respectively. Reproducibility and recovery were good. The method was successfully applied to the determination of ketoconazole and econazole nitrate in human blood samples.     

Multi-residue method for trace level determination of pharmaceuticals in solid samples using pressurized liquid extraction followed by liquid chromatography/quadrupole-linear ion trap mass spectrometry

A simple and sensitive method for simultaneous analysis of 43 pharmaceutical compounds in sewage sludge and sediment samples was developed and validated. The target compounds were extracted using pressurized liquid extraction (PLE) and then purified and pre-concentrated by solid phase extraction (SPE) using a hydrophilic-lipophilic balanced polymer. PLE extraction was performed on temperature of 100 °C, with methanol/water mixture (1/2, v/v) as extraction solvent. The quantitative analysis was performed by liquid chromatography tandem mass spectrometry using a hybrid triple quadrupole-linear ion trap mass spectrometer (LC-QqLIT-MS). Data acquisition was carried out in selected reaction monitoring (SRM) mode, monitoring two SRM transitions to ensure an accurate identification of target compounds in the samples. Additional identification and confirmation of target compounds were performed using the Information Dependent Acquisition (IDA) function. The method was validated through the estimation of the linearity, sensitivity, repeatability, reproducibility and matrix effects. The internal standard approach was used for quantification because it efficiently corrected matrix effects. Despite the strong matrix interferences, the recoveries were generally higher of 50% in both matrixes and the detection and quantification limits were very low. Beside the very good sensitivity provided by LC-QqLIT-MS, an important characteristic of the method is that all the target compounds can be simultaneously extracted, treated and analysed. Hence, it can be used for routine analysis of pharmaceuticals providing large amount of data. The method was applied for the analysis of pharmaceuticals in river sediment and wastewater sludge from three treatment plants with different treatment properties (i.e. capacity, secondary treatment, quality of influent waters). The analysis showed a widespread occurrence of pharmaceuticals in the sludge matrices.     

Determination of Chlorophenols in Sewage Sludge and Soil by High-Performance Liquid Chromatography–Tandem Mass Spectrometry with Ultrasonic-Assisted and Solid-Phase Extraction

Chlorophenols are a category of toxic pollutants that are ubiquitously present in the environment. This paper presents a reliable and feasible method for the determination of five chlorophenols in sewage sludge and soil using liquid chromatography–tandem mass spectrometry (LC-MS/MS). The pretreatment involved ultrasonic-assisted extraction and solid-phase extraction purification with hydrophilic–lipophilic balance cartridges. LC-MS/MS equipped with an electrospray ionization source operated in negative mode was used for detection, and multitude reaction monitoring mode was applied for data acquisition. The pretreatment and working conditions of LC-MS/MS were optimized to achieve satisfactory results. The intra-batch accuracies were 100.5–113.4% with relative standard deviations?≤?15.6% for the chlorophenols in sewage sludge and 71.3–102.7% with relative standard deviations?≤?14.0% for those in soil. The inter-batch accuracies were 86.1–100.5% (relative standard deviations?≤?33.6%) for sewage sludge samples and 70.5–112.5% (relative standard deviations?≤?28.2%) for soil samples, respectively. This method has been applied to the determination of chlorophenols in sewage sludge of wastewater treatment plants and soil collected from Guangzhou, China. Parachlorophenol, 2,4,6-trichlorophenol, 2,3,4,6-tetrachlorophenol, and pentachlorophenol were detected in some sewage sludge samples, with concentrations from 0.51 to 13.20?ng/g. In addition, parachlorophenol, 2,3,4,6-tetrachlorophenol, and pentachlorophenol were found in all the soil samples with concentrations from 0.33 to 5.21?ng/g. The chromatographic behavior, on-filter adsorption behavior, and the relationship between optimal collision energies and degree of chlorination of the chlorophenols was investigated. This method will be conducive to environmental research focusing on pollution investigation of chlorophenols in the environment.     

Fully automated determination of 74 pharmaceuticals in environmental and waste waters by online solid phase extraction-liquid chromatography-electrospray-tandem mass spectrometry

The present work describes the development of a fully automated method, based on on-line solid-phase extraction (SPE)-liquid chromatography-electrospray-tandem mass spectrometry (LC-MS-MS), for the determination of 74 pharmaceuticals in environmental waters (superficial water and groundwater) as well as sewage waters. On-line SPE is performed by passing 2.5 mL of the water sample through a HySphere Resin GP cartridge. For unequivocal identification and confirmation two selected reaction monitoring (SRM) transitions are monitored per compound, thus four identification points are achieved. Quantification is performed by the internal standard approach, indispensable to correct the losses during the solid phase extraction, as well as the matrix effects. The main advantages of the method developed are high sensitivity (limits of detection in the low ng L⁻¹ range), selectivity due the use of tandem mass spectrometry and reliability due the use of 51 surrogates and minimum sample manipulation. As a part of the validation procedure, the method developed has been applied to the analysis of various environmental and sewage samples from a Spanish river and a sewage treatment plant.