Online solid-phase extraction–liquid chromatography–electrospray–tandem mass spectrometry determination of multiple classes of antibiotics in environmental and treated waters

An online solid-phase extraction and liquid chromatography in combination with tandem mass spectrometry method was developed for the simultaneous determination of 31 antibiotics in drinking water, surface water and reclaimed waters. The developed methodology requires small sample volume (10 mL), very little sample preparation and total sample run time was 20 min. An Ion Max API heated electrospray ionization source operated in the positive mode with two selected reaction monitoring transitions was used per antibiotic for positive identity and quantification performed by the internal standard approach, to correct for matrix effects and any losses in the online extraction step. Method detection limits were in the range of 1.2–9.7, 2.2–15, 5.5–63 ng/L in drinking water, surface water and reclaimed waters, respectively. The method accuracy in matrix spiked samples ranged from 50–150 % for the studied antibiotics. The applicability of the method was demonstrated using various environmental and reclaimed water matrices. Erythromycin was detected in more than 85 % of the samples in all matrices (28–414, n.d.–199, n.d.–66 ng/L in reclaimed, river and drinking waters respectively). The other frequently detected antibiotics in reclaimed waters were nalidixic acid, clarithromycin, azithromycin, trimethoprim, and sulfamethoxazole.     

Highly sensitive simultaneous determination of sulfonamide antibiotics and one metabolite in environmental waters by liquid chromatography-quadrupole linear ion trap-mass spectrometry

The present work describes the development of a highly sensitive analytical method based on liquid chromatography-quadrupole linear ion trap-mass spectrometry (LC-QqLIT-MS) for the determination of nine sulfonamide antibiotics and one N4-acetylated metabolite in environmental waters (wastewater, surface water and groundwater) and bottled mineral water. Special emphasis was devoted to the elimination of matrix components during solid-phase extraction (SPE) by the evaluation of three different extraction/purification strategies: single cartridges (Oasis HLB and Oasis MCX) and tandem (TD) extraction (combination of both). The method developed proved to be suitable for sulfonamide determination in all kinds of waters tested. The method was shown to be linear in a wide concentration range, with correlation coefficients higher than 0.999 for all compounds except for sulfadimethoxine (R2 0.997). The overall instrumental repeatability was satisfactory, with the exception of the metabolite (RSD 34%). Method limits of detection achieved for sulfonamides were in the range 0.01-1.13 ng L(-1) and for the metabolite 0.08-461 ng L(-1). Recovery rates were estimated at 500 ng L(-1) spike level in the four water matrices selected. The highest recovery achieved in all matrices was that corresponding to the Oasis HLB cartridge. In environmental waters, recovery values obtained were higher than 61% for the surface water and, in general, higher than 90% for groundwater and wastewater. Bottled mineral water exhibited recovery rates higher than 92%, with the exception of sulfamethoxypiridazine (82%) and sulfapyridine (86%) In order to demonstrate the applicability of the developed method, several water samples were analyzed. Results evidenced the requirement for consideration of N4-acetylated metabolites of sulfonamides in environmental residue analysis to avoid the underestimation of removal rates of such pharmaceutical compounds during wastewater treatments.     

Improved analysis of volatile halogenated hydrocarbons in water by purge-and-trap with gas chromatography and mass spectrometric detection

An analytical system composed of a purge-and-trap injection system coupled to gas chromatography with mass spectrometric detection (PTI-GC-MS) specific for the analysis of volatile chlorinated hydrocarbons (VCHCs) (chloroform; 1,1,1-trichloroethane; tetrachloromethane; 1,1,2-trichloroethylene; tetrachloroethylene) and trihalomethanes (THMs) (chloroform; bromodichloromethane; dibromochloromethane; bromoform) in water was optimised. Samples were purged and trapped in a cold trap (-100 degrees C) fed with liquid nitrogen (cryo-concentration). In order to make this method suitable also for only slightly contaminated waters, some modifications were made to PTI sample introduction, in order to avoid any air intake into the system. PTI, GC and MS conditions were optimised for halogenated compound analysis and limits of detection (LOD) were evaluated. The proposed method allows analysis of samples whose concentrations range from microg/L to ng/L. It is, therefore, applicable to drinking waters, in analyses required by law, and to slightly contaminated aqueous matrices, such as those found in remote areas, in environmental monitoring. Moreover, by changing cold trap temperature, even sparkling mineral waters can be analysed, thus avoiding CO2 interference during the cryo-concentration phase. Our method has been successfully used on real samples: tap water, mineral water and Antarctic snow.     

Automated analysis of geosmin, 2-methyl-isoborneol, 2-isopropyl-3-methoxypyrazine, 2-isobutyl-3-methoxypyrazine and 2,4,6-trichloroanisole in water by SPME-GC-ITDMS/MS

This paper describes a method of determining the following compounds in water characterised by complex matrices (raw waters and drinking waters): geosmin, 2-methylisoborneol (2-MIB), 2-isobutyl-3-methoxypyrazine (IBM), 2-isopropyl-3-methoxypyrazine (IPM) and 2,4,6-trichloroanisole (TCA). The method is carried out using headspace solid-phase microextraction (HS-SPME) combined with gas chromatography (GC) and ion trap mass spectrometry (ITMS). Several parameters of extraction and desorption were optimised through the use of a Combi PAL autosampler to automate various tasks (temperature extraction, extraction time, stir speed). Quantities of NaCl and the liquid volume/total volume ratio were also optimised. Double fragmentation (tandem MS/MS) was optimised on the target compounds. The method resulted in good linearity obtained for concentrations of 1 to 100?ng?L^?1 and provided detection limits of approximately below 1?ng?L^?1. Good precision (1–8%) was obtained. This method was successfully applied to the analysis of earthy and musty odours in municipal raw source waters with high concentrations of natural organic matter and in the corresponding treated waters. This is the first time MS/MS has been used to analyse odorous compounds in waters destined for human consumption. In addition, the method as developed is simple to use and lends itself to easy interpretation of chromatograms.     

New developments in the analysis of fragrances and earthy-musty compounds in water by solid-phase microextraction (metal alloy fibre) coupled with gas chromatography-(tandem) mass spectrometry

Fragrances are widespread aquatic contaminants due to their presence in many personal care products used daily in developed countries. Levels of galaxolide and tonalide are commonly found in surface waters, urban wastewaters and river sediments. On the other hand, earthy-musty compounds confer bad odour to drinking water at levels that challenge the analytical capabilities. The combined determination of earthy-musty compounds and fragrances in water would be a breakthrough to make the traditional organoleptic evaluation of the water quality stricter and safer for the analyst. Two approaches were attempted to improve the analytical capabilities: analyte pre-concentration with a newly developed PDMS-DVB solid-phase microextraction fibre on metal alloy core and sensitive detection by tandem mass spectrometry (MS/MS). The optimization of SPME parameters was carried out using a central composite design and desirability functions. The final optimum extraction conditions were: headspace extraction at 70 °C during 40 min adding 200 g L⁻¹ of NaCl. The detection limits in tandem MS (0.02-20 ng L⁻¹) were marginally lower compared to full scan except for geosmin and trichloroanisol which go down to 0.1 and 0.02 ng L⁻¹, respectively.The analysis of different water matrices revealed that fragrances and earthy-musty compounds were absent from ground- and drinking waters. Surface waters of river Leça contained levels of galaxolide around 250 ng L⁻¹ in the 4 terminal sampling stations, which are downstream of WWTPs and polluted tributaries. Geosmine was ubiquitously distributed in natural waters similarly in rivers Leça and Douro at concentrations <7 ng L⁻¹.     

Determination of Ethylenethiourea (ETU) at Trace Levels in Water Samples by Cathodic Stripping Voltammetry

A stripping voltammetric method for the determination of ethylenethiourea in water samples is described based on its adsorptive deposition at the hanging mercury drop electrode (HMDE). In a borate buffer (pH 9.0) as supporting electrolyte, ETU is deposited at +100 mV (vs. Ag/AgCl) and stripped during the cathodic scan. The linear range for the measurements was from 2.0 to 100 μg L^?1, with a detection limit calculated as 1.4 μg L^?1 after a deposition time of 300 s and a RSD of 1.9% (n=5) for 50 μg L^?1 of ETU measured. The interferences of some organic compounds and metallic ions were tested. Recoveries between 93 and 110% were obtained using the standard addition method for spiked samples of natural and drinking waters. The method is rapid and applicable in the monitoring of ETU residues in water samples.     

Analysis of UV filters in tap water and other clean waters in Spain

The present paper describes the development of a method for the simultaneous determination of five hormonally active UV filters namely benzophenone-3 (BP3), 3-(4-methylbenzylidene) camphor (4MBC), 2-ethylhexyl 4-(dimethylamino) benzoate (OD-PABA), 2-ethylhexyl 4-methoxycinnamate (EHMC) and octocrylene (OC) by means of solid-phase extraction and gas chromatography–electron impact ionization–mass spectrometry. Under optimized conditions, this methodology achieved low method limits of detection (needed for clean waters, especially drinking water analysis), between 0.02 and 8.42 ng/L, and quantitative recovery rates higher than 73% in all cases. Inter- and intraday precision for all compounds were lower than 7% and 11%, respectively. The optimized methodology was applied to perform the first survey of UV absorbing compounds in tap water from the metropolitan area and the city of Barcelona (Catalonia, Spain). In addition, other types of clean water matrices (mineral bottled water, well water and tap water treated with an ion-exchange resin) were investigated as well. Results evidenced that all the UV filters investigated were detected in the water samples analyzed. The compounds most frequently found were EHMC and OC. Maximum concentrations reached in tap water were 290 (BP3), 35 (4MBC), 110 (OD-PABA), 260 (EHMC), and 170 ng/L (OC). This study constitutes the first evidence of the presence of UV filter residues in tap water in Europe.     

Isolation of Chromium(VI) from Aqueous Solution by Electromembrane Extraction

Electromembrane extraction (EME) is a powerful extraction and preconcentration technique for ionizable species. However, the ionic contents in the sample can influence the extraction efficiency and system stability due to electrolysis. In this work, the electromembrane extraction of chromium(VI) was developed using various levels of ionic samples. 2-Nitrophenyl octyl ether was the most suitable supported liquid membrane that delayed the electrolytic occurrence of air bubbles at the electrodes due to its high viscosity and high dielectric constant properties. The electromembrane extraction method was optimized using 5?mM NaCl (630?µS?cm^?1); the applied potential was 100?V and the extraction time was 15?min. The enrichment factor of 80 was obtained over a linear working range of 10.0–80.0?µg?L^?1. The method performance was tested using mineral water, drinking water, tap water, and surface water. The method recoveries based on matrix-matched calibration were 95–125% with standard deviations within 15%.     

Analysis of 32 priority substances from EU water framework directive in wastewaters,surface and drinking waters with a fast sample treatment methodology

A simple, fast, and sensitive method is proposed for the analysis of 32 priority substances (PS) from EU Water Framework Directive (WFD) and the first Watch List in effluents of wastewater treatment plants (EWW), surface waters (SW) and drinking waters (DW). Dispersive liquid-liquid microextraction (DLLME) and gas chromatography coupled to tandem mass spectrometry (GC-MS/MS) is used. For DLLME, a mixture of 1,1,2-trichloroethane as extraction solvent (75 µL) and acetonitrile as disperser solvent (3.2 mL) is proposed. The method was validated in EWW, SW and DW, showing satisfactory accuracy values ranging from 90% to 104%, good precision (relative standard deviation, RSD%, lower than 13%) and uncertainty values between 7% and 34%. Regarding sensitivity, method limits of quantification (MLOQs) of 4.8, 5.2 and 8.8 ng L^?1 for DW, SW and EWW, respectively, were obtained. The developed method was applied to analyze PS in water from effluents of waste water treatment plants (WWTPs), surface water of the Llobregat River and its main tributaries (Catalonia, NE Spain) and drinking water from a Drinking Water Treatment Plant (DWTP). Moreover, the efficiency of treatment plants (DWTP, WWTP) on the elimination of PS was evaluated. Only 3 PS (lindane, terbutryn and dicofol) were detected, being terbutryn the compound found at the highest levels (up to 493 ng L^?1 in EWW samples). Regarding environmental quality standard (WFD) for terbutryn in surface waters, only one sample, the Rubí stream (431 ng L^?1), showed levels of terbutryn higher than maximum allowable concentration (340 ng L^?1).     

Multi-residue analysis of pharmaceutical compounds in aqueous samples

Pharmaceutical compounds are nowadays an emerging group of organic pollutants in aquatic systems. Several methodologies have already been published to measure these pollutants in the environment, showing the difficulties to take into account the various compounds belonging to numerous therapeutical and chemical groups. In order to develop environmental monitoring, there is a need for a less costly and time-consuming multi-component procedure. The work presented here deals with the development of an extraction procedure which enables the measurement of a wide spectrum of pharmaceuticals at trace levels (ng 1(-1)) with quite simple equipment (i.e. GC-MS with single quadruple as analyzer). The analyzed compounds comprise anti-inflammatories, antidepressants and hypolipidic drugs. The reliability and sensitivity have been tested on 18 different compounds (7 basic compounds and 11 acidic drugs) extracted simultaneously and analyzed by GC-MS. The optimized procedure has been successfully applied to the analysis of wastewaters, surface waters and drinking waters from the following areas: first the Cortiou rocky inlet, in the Mediterranean Sea (South coast of France), highly impacted by the Marseilles wastewater treatment plant effluent and secondly the Hérault watershed by studying drinking water, surface water and wastewater. In both cases, the level of pharmaceuticals was totally unknown. Results obtained have demonstrated the suitability of the method for multi-residue analysis of different types of water matrices.     

Development and application of methods using SPE,HPLC-DAD,LC-ESI-MS/MS and GFAAS for the determination of herbicides and metals in surface and drinking water

A preliminary study of the pollution in surface and drinking waters caused by herbicides and metals in the Municipal Water Supply System (CORSAN) in Rio Grande city, RS, Brazil, is reported. The occurrence of 5 herbicides and 9 metals was studied in surface and drinking water through the analysis of 2 sampling spots at CORSAN. The analytical determination was performed by solid-phase extraction (SPE), high performance liquid chromatography-photodiode array detection (HPLC-DAD) and liquid chromatography coupled to electrospray ionisation tandem mass spectrometry (LC-ESI-MS/MS) for herbicides, and graphite furnace atomic absorption spectrometry (GFAAS) for metals. The concentrations of herbicides in the surface water were very low; however, the herbicide clomazone was detected in more than 50% of the samples analysed in concentration exceeding 1.0?µg L^?1. The concentration of metals was below the Maximum Contaminant Level (MCL) set by the Brazilian regulation.     

Novel chromatographic separation and carbon solid-phase extraction of acetanilide herbicide degradation products

One acetamide and 5 acetanilide herbicides are currently registered for use in the United States. Over the past several years, ethanesulfonic acid (ESA) and oxanilic acid (OA) degradation products of these acetanilide/acetamide herbicides have been found in U.S. ground waters and surface waters. Alachlor ESA and other acetanilide degradation products are listed on the U.S. Environmental Protection Agency's (EPA) 1998 Drinking Water Contaminant Candidate List. Consequently, EPA is interested in obtaining national occurrence data for these contaminants in drinking water. EPA currently does not have a method for determining these acetanilide degradation products in drinking water; therefore, a research method is being developed using liquid chromatography/negative ion electrospray/mass spectrometry with solid-phase extraction (SPE). A novel chromatographic separation of the acetochlor/alachlor ESA and OA structural isomers was developed which uses an ammonium acetate-methanol gradient combined with heating the analytical column to 70 degrees C. Twelve acetanilide degradates were extracted by SPE from 100 mL water samples using carbon cartridges with mean recoveries >90% and relative standard deviations < or =16%.     

Trace determination of beta-lactam antibiotics in surface water and urban wastewater using liquid chromatography combined with electrospray tandem mass spectrometry

A sensitive and reliable method using liquid chromatography-electrospray tandem mass spectrometry has been developed and validated for the trace determination of beta-lactam antibiotics in natural and wastewater matrices. Water samples were enriched by solid-phase extraction. The analytes included amoxicillin (AMOX), ampicillin (AMP), oxacillin (OXA), cloxacillin (CLOX) and cephapirin (CEP). Average recoveries of beta-lactams (BLs) in fortified samples were generally above 75% (except amoxicillin) with the standard deviations lower than 10% in water matrices. Amoxicillin was not quantified due to poor recovery (less than 40%) in the investigated water matrices. Matrix effects were found to be minimal when measuring these compounds in water matrices. The accuracy, within- and between-run precision of the assay fell within acceptable ranges of 15% absolute. The method detection limit (MDL) was estimated to range between 8 and 10 ng/L in surface water, 13 and 18 ng/L in the influent and 8 and 15 ng/L in the effluent from a wastewater treatment plant. A large number of actual water samples were analyzed using this method in order to evaluate the occurrence of the beta-lactams in a river and a wastewater treatment plant in northern Colorado. Most of the samples were negative for all analytes. These compounds were found at 15-17 ng/L in the three influent samples and at 9-11 ng/L in three surface water samples out of a total of 200 samples. This indicates that contamination by beta-lactam antibiotics is of minor importance to the small mixed-watershed.     

Solid‐phase extraction coupled with ultra high performance liquid chromatography and electrospray tandem mass spectrometry for the highly sensitive determination of five iodinated X‐ray contrast media in environmental water samples

A highly sensitive method based on solid‐phase extraction and ultra high performance liquid chromatography with electrospray tandem mass spectrometry has been developed for simultaneous determination of five iodinated X‐ray contrast media in environmental water samples. Various solid‐phase extraction cartridges have been evaluated and a combination of LiChrolute EN and ENVI‐Carb solid phase extraction cartridges was selected for sample enrichment. The method was comprehensively validated on ground water, tap water, surface water, drinking water, and waste water by the conventional procedures: linearity, method detection limits, accuracy and precision, matrix effects. Good linearity (R² > 0.999), low detection limits (0.4–8.1 ng/L), satisfactory recoveries (55.1–109.5%) and precision (0.8–10.0% for intra‐day precisions and 0.6–16.5% for inter‐day precisions) were obtained for all the target compounds. Iopamidol, iohexol, and diatrizoate in some matrices were affected by matrix effects, which were slightly eased by using the isotope‐labeled internal standard. The developed method was successfully applied for real samples collected in Shanghai, China, with detected concentrations up to 2200 ± 200 and 9000 ± 1000 ng/L for iohexol and iopamidol, respectively.     

Development,validation, and application of a novel LC-MS/MS trace analysis method for the simultaneous quantification of seven iodinated X-ray contrast media and three artificial sweeteners in surface,ground, and drinking water

A new method for the simultaneous determination of iodated X-ray contrast media (ICM) and artificial sweeteners (AS) by liquid chromatography-tandem mass spectrometry (LC-MS/MS) operated in positive and negative ionization switching mode was developed. The method was validated for surface, ground, and drinking water samples. In order to gain higher sensitivities, a 10-fold sample enrichment step using a Genevac EZ-2 plus centrifugal vacuum evaporator that provided excellent recoveries (90?±?6 %) was selected for sample preparation. Limits of quantification below 10 ng/L were obtained for all compounds. Furthermore, sample preparation recoveries and matrix effects were investigated thoroughly for all matrix types. Considerable matrix effects were observed in surface water and could be compensated by the use of four stable isotope-labeled internal standards. Due to their persistence, fractions of diatrizoic acid, iopamidol, and acesulfame could pass the whole drinking water production process and were observed also in drinking water. To monitor the fate and occurrence of these compounds, the validated method was applied to samples from different stages of the drinking water production process of the Industrial Works of Basel (IWB). Diatrizoic acid was found as the most persistent compound which was eliminated by just 40 % during the whole drinking water treatment process, followed by iopamidol (80 % elimination) and acesulfame (85 % elimination). All other compounds were completely restrained and/or degraded by the soil and thus were not detected in groundwater. Additionally, a direct injection method without sample preparation achieving 3–20 ng/L limits of quantification was compared to the developed method.     

Simultaneous determination of base/neutral and acid herbicides in natural water at the part per trillion level

Summary A new method for the simultaneous identification and quantification of base/neutral and acidic pesticides at a low nanogram per liter concentration level in natural waters is presented. The method includes enrichment of the compounds by solid phase extraction on graphitized carbon black, followed by sequential elution of the base/neutral and acidic pesticides. Identification and quantification of the compounds is performed with HPLC-ESI-MS. This procedure involves passing 1 L of ground water and 2 L of drinking water samples through a 0.5 g graphitized carbon black (GCB) extraction cartridge. A conventional 4.6-mm-i.d. reversed phase LC C-18 operating with a 1 mL min⁻¹ flow of the mobile phase was used to chromatograph the analytes. A flow of 100 μL min⁻¹ of the column effluent was diverted to the ESI source. The ESI source was operated in positive ion mode for base/neutral pesticides and in negative-ion mode for acid pesticides. For the analyte considered, the response of the mass detector was linearly related to the amount of the analytes injected between 5 and 250 ng. In all cases, recoveries of the analytes were better than 90%. The limit of detection (signal-to-noise ratio=3) of the method for the pesticides considered in drinking water samples was estimated to be about 3–10 ng L⁻¹.     

Trace analysis of isothiazolinones in water samples by large-volume direct injection liquid chromatography tandem mass spectrometry

Isothiazolinones are used as preservatives, biocides and disinfectants in a variety of industrial and domestic applications. Some of the isothiazolinones are difficult to isolate from water due their high polarity. A sensitive and selective analytical method was developed and optimized for the determination of sub-μg/L levels of three isothiazolinones in water samples. Three isothiazolinones are described in this paper: 2-methyl-3-isothiazolinone, 5-chloro-2-methyl-3-isothiazolinone and 4,5-dichloro-2-methyl-3-isothiazolinone. The analytical method involves a robust large-volume direct on-column loop injection of 2 mL on an Aqua ODS HPLC column and tandem MS detection (HPLC–MS/MS). After filtration, samples are directly injected without further pretreatment. Detection limits of the individual target compounds were between 0.03 and 0.1 μg/L employing Multi-Reaction Monitoring (MRM) mass spectrometry. Based on the constant ratio of two selected product-ions together with the retention time, the identification is very selective and quantification is reliable. The method was successfully applied to real samples of membrane flushings, drinking water, surface waters and waste water. Additional investigations showed the instability of the isothiazolinones in river- and waste water. Preservation of river water and waste water samples with sodium azide (NaN₃) promotes the stability of the isothiazolines in solution. In membrane flushings, waste water, surface waters and drinking water, levels of the three isothiazolinones were all below the limit of detection. In effluents of households containing washings from normal shampoo use, isothiazolinones could be detected.     

Determination of tritium in water using electrolytic enrichment: methodology improvements

The quality control of the method for tritium (³H) determination in water after electrolytic concentration by liquid scintillation counting measurements was improved considering more parameters in the uncertainty budget, besides the control charts to evaluate the electrolytic enrichment factor, the enrichment parameter and blank samples. The quality control upgrade of the method and the participation in proficiency tests allow its optimization. This methodology was applied to the determination of ³H activity concentrations in waters from different origins: surface, rain and drinking waters.     

Determination of phenylurea herbicides in natural waters at concentrations below 1 ng l using solid-phase extraction, derivatization, and solid-phase microextraction–gas chromatography–mass spectrometry

A procedure is presented which allows the ultratrace level determination of phenylurea herbicides (PUHs) in natural waters. Samples were enriched by solid-phase extraction (SPE) on Carbopack B and alkylated with iodoethane and sodium hydride to yield thermostable products. After derivatization, the aqueous samples were extracted and injected by SPME. The use of iodoethane instead of iodomethane allowed the differentiation between parent compounds and the N-demethylated metabolites. Limits of detection were between 0.3 and 1.0 ng/l for the parent compounds. Standard deviations below 10% were achieved for samples containing more than 4 ng/l in very different matrices including Nanopure water, lake water, and waste water treatment plant (WWTP) effluent. Moreover, the para-hydroxylated metabolite of diuron could be quantified with the same procedure. The presence of further metabolites was assessed qualitatively. Chromatography was stable over a large number of measurements even with dirty samples from WWTP effluent. The precision and sensitivity of the developed analytical method allowed the investigation of the fate of PUHs in lakes, their degradation during drinking water treatment and their transport within the North Sea.