Determination of Hg in biological samples by substoichiometric neutron activation analysis

The method described here involves the irradiation of biological samples and a g quantity of standard with thermal neutrons at the self-serve position in the CIRUS reactor, followed by dissolution of the sample and standard in the presence of milligram amounts of carrier. Both the sample and the standard are subjected to substoichiometric extraction under controlled experimental conditions with ethyl thioacetoacetate into chloroform. An aliquot of the organic phase is counted on a -spectrometer. The concentration of Hg in various biological samples and the accuracy, precision, and sensitivity of the method are discussed.     

Determination of trace amounts of gold in acid-attacked environmental samples by atomic absorption spectrometry with electrothermal atomization after preconcentration

A method for determination of trace amounts of gold in environmental samples (rocks, soils, sediments, and waters) by atomic absorption spectrometry with electrothermal atomization (ETAAS) after preconcentration using a chelating sorbent Spheron Thiol 1000 is described. The method accurately determines gold between 0.001 and several tens of grams per ton in samples having complex variations in mineralogy. Pulverized samples are roasted at 650°C to oxidize any sulfide and/or carbonaceous material. Samples are then subjected to a series of acid treatments to eliminate any silica matrix and to dissolve the sample. The Spheron Thiol 1000 is added to the sample solution, and then with sorbed gold is filtered out, washed, and ignited at 550°C. The residue is dissolved in aqua regia, evaporated, dissolved in distilled water, transferred to a volumetric flask, and analyzed by ETAAS.The limits of detection of gold, based on the 3 definition, were 0.5 ng g^–1 for 10-g samples (rocks, sediments, soils) and 0.05 ng mL^–1 for 1-L water samples. Precision of determination expressed by the relative standard deviation varied from 2.9% to 16.4%. The accuracy of the method is verified by analysis of certified reference materials. The obtained analytical results are in good agreement with attested values. The developed method was applied for gold determination in environmental samples affected by the acidification (acid mine drainage which is mainly a product of pyrite oxidation) from an open quartzite mine in the obov region situated NE of the city of Banská tiavnica (Slovakia).     

Efficient radiochemical separation for the determination of plutonium in environmental samples,using a supported,highly specific extractant

A radiochemical separation procedure has been developed for a very efficient isolation of plutonium from environmental samples. Essentially, the method involves the following steps: ashing of the sample and preparation of the load solution; separation of plutonium by a column containing a commercially available, highly specific, supported extractant; electrodeposition of Pu and subsequent -spectrometry. Detailed procedures are reported for liver samples and for soil. The modifications necessary for sample sizes above 5 g dry weight and up to 200 g are also given. Recoveries of added tracers are 60–70%. The precision of the method is <10% (RSD). The accuracy was examined by analyzing also certified standard reference materials. Due to the very efficient isolation of Pu, the resulting -spectrum is virtually free of interfering -emitters of Th and U.     

Substoichiometric determination of Cd by neutron activation analysis

A rapid method has been developed for the determination of cadmium in environmental samples by thermal neutron activation analysis involving substoichiometric extraction with 1,2,3-benzotriazole /1,2,3-BT/. Cd was radiochemically separated as CdS using 1-amidino-2-thiourea. The time required for radiochemical purification containing two samples and a standard was about 2 h. 4.63 g of Cd can be determined with an accuracy of 6.69% and precision of 6.25%. Mash potatoes, animal bones, raw sludge and cattle manure have been analyzed by this method.     

Prediction of FCC gasoline octane numbers using FT-MIR and PLS

A method for predicting octane numbers (RON and MON) in fluid catalytic cracking (FCC) gasolines is proposed. Using FT-MIR and PLS, improvements have been obtained in sample throughput, reduced delay times, accuracy (repeatability and reproducibility), amounts of samples and reagents and environmental working conditions when compared with current standard methods. A total number of 140 daily production samples were taken; and from there, a learning group was prepared (44 samples); a validation set (96 samples) was prepared, as well. Sample spectra were recorded from 4000 to 600 cm^-1 at 4 cm^-1 intervals (traditional sealed NaCl cells). The PLS technique was used in its two variants (1 and 2-block). Both provided similar results. Their predictive characteristics are very good: SEP_RON=0.38; SEP_MON=0.40; repeatability <0.1 O.N.; reproducibility <0.3 O.N. (SEP=Standard Error of Prediction).     

Rapid determination of fluorine in coral skeletons by non-destructive neutron activation analysis using 20F

A rapid non-destructive technique has been proposed for the determination of fluorine in coral skeletons by thermal neutron activation analysis, using the short half-life ²⁰F nuclide (11.0 s). About 0.2-0.5 g samples were irradiated for 10 seconds in a Triga Mark II Reactor. Soon after the irradiation (25-35 s), measurements of -rays were performed with each sample and standard. The method has the drawback of low sensitivity (20 ppm of F), and the manual operation employed in the cooling step could lead to less precise measurements. We determined fluorine in coral standards within ~8% of analytical precision. The result obtained for the dolomite standard was fairly consistent with literature values, but those for the limestone standard showed to be considerably higher than the reported values. The present method was applied for the determination of fluorine in modern corals from Khang Khao Island, Thailand and Okinawa, Japan. Two core samples of an ancient reef from Funafuti Atoll were measured for fluorine to compare with modern samples. In order to understand the environmental media in which coral grew, the partition of fluorine between seawater and coral skeletons is also discussed.     

Microwave assisted extraction for mercury speciation analysis

The application of microwave-assisted extraction (MAE) to the work-up of environmental and biological samples in the study of mercury speciation analysis has increased in recent years and is now increasingly accepted as a standard approach. The review provides a brief theoretical background of microwave heating and the basic principles of microwave energy used for extraction. The advantages and disadvantages of (a) MAE techniques, (b) the influence of the main parameters affecting the extraction, (c) statistical optimization approaches, and (d) strategies for method validation also are highlighted. Recent applications of MAE to mercury species analyses in biological samples, soils, sediments, and crude oil samples are surveyed and critically reviewed. In addition, comparisons of its use with other well-established extraction procedures are discussed.

Optimizing the results in alpha-spectrometry of very low-level activity samples when the spike used is present in the sample

Determination of very low-level activity in samples using -spectrometry is possible due to the low background. In order to determine the chemical yield in the separation of the element of interest, a spike must be added to the sample. In many practical cases there is no adequate spike or it is not available in the laboratory. In these cases a spike of the radionuclide already pesent in the sample can be used as the so-called inner standard method. In order to achieve the best results the optimal quantity and the spike to choose must be determined to reduce the uncertainties associated with the activities. The present work is a systematic study of these problems. These considerations were used to the determination of thorium in environmental samples.     

PROZA and CALIBRATION CURVES for Quantitative X-Ray Microanalysis of Biological Samples

The main scope of our work was to investigate the usefulness of the PROZA correction method and CALIBRATION CURVE construction for quantitative X-ray microanalysis of biological soft, freeze-dried tissues. The test samples with a known elemental concentration of NaCl, MgCl₂, KH₂PO₄ and Na₂SO₄ were prepared on the basis of 20% porcine skin gelatine. A control sample containing 20% gelatine was used for sulphur subtraction. Dissolved gelatine solutions were cooled with liquid nitrogen and then cut in cryomicrotome into 16µm thick slices. The sections were lyophilised, coated with carbon and analysed by means of a scanning electron microscope combined with an energy dispersive (ED) spectrometer. The homogeneity of the prepared samples was verified using the Fishers test. Only homogenous samples were used for calibration. The significance of the (z) (PROZA) correction method for biological sample analysis was verified by comparing the prepared standard and entering it into the Voyager computer program memory with the remaining samples of a known elemental content. The differences between the standard and the samples were noted for all elements analysed. There was no sample matching the standard after the PROZA correction procedure. A high correlation r factor (above 0.99) for all analysed elements indicates that CALIBRATION CURVES construction could be suitable for quantitative X-ray microanalysis of biological samples.     

On-line sample preparation and determination of phenols with a Flow-Analysis method

Summary A Flow-Analysis system has been developed to automate the phenol determination according to the German standard method DIN 38409-H16-2. The automation leads to a significant acceleration of the procedure. One analysis only lasts 3 min while the complete manual determination requires 3 h. Also the sample, solvent and reagent volumes are reduced to a tenth of the volumes demanded by the standard method. The described phenol determination is based on the integration of an airsegmented (Airsegmented-Flow-Analysis SFA) part in a Flow-Injection-Analysis (FIA) system. The main steps of the analytical procedure are: Reproducible inserting of the sample in a carrierstream, sample pretreatment and sample measuring. In the first step the sample is injected into the carrierstream. It transports the sample in the reactioncoil and than through the distillation unit. The steam distillation represents the sample preparation step; therefore an airsegmented stream is necessary. Afterwards the different phases (liquid and gas) were singled again and the distilled solution is fed into the FIA manifold. The determination itself takes place inside the FIA system. The limit of determination amounts to 0.01 mg l^–1 with a standard deviation of 1.5%. Different waste, surface and drinking water samples have been analyzed without any problems. The results correspond very well to those obtained by manual procedure.     

Adsorption voltammetric techniques for the determination of uranium(VI) with 2,5-dichloro-3,6-dihydroxy-1,4-benzoquinone as complex forming reagent

Uranium (VI) can be determined by adsorptive voltammetric techniques, as its chloranilic acid complex, over a wide concentration range. Differential pulse polarography is useful for quantification of uranium between 0.1 and 1.5 mg/l; for the range from 10 to 500 g/l differential pulse voltammetry and for ultra-trace analysis between 0.024 and 40 g/l adsorptive stripping voltammetry are preferred. The standard deviation for the 3-detection limit of 24 ng/l uranium was found to be 8%. In the trace analysis of metals in aquatic environmental systems by adsorptive stripping voltammetry it is normally necessary to decompose polluted water samples by UV irradiation or microwave digestion. The advantage of the developed method is the fact that no sample pretreatment is necessary.Dedicated to Professor R. Geyer on the occasion of his 80th birthday     

Uranium in coral skeletons determined by epithermal neutron activation analysis

A simple and non-destructive method has been proposed for the routine determination of uranium by epithermal neutron activation analysis in coral skeletons. Using a cadmium capsule, about 0.1-0.2 g samples were irradiated for 6 hours in the Triga Mark II Reactor. Measurements of -ray (²³⁹Np via ²³⁹U) were performed with each sample and standard after cooling for about three days. Compared with a non-destructive thermal NAA, the present method was found to improve the sensitivity because it reduced the intense Compton background induced by ²⁴Na. We determined uranium in coral standards within 2% of analytical precision. The data obtained for the carbonate standards are mostly consistent with reported values. The present method could be usefully applied to determine uranium contents in fossil corals from the Funafuti Atoll in the Pacific. The distribution of uranium between seawater and coral skeletons is also discussed in order to understand the environmental media in which the coral grew.     

Determination of pyridine in soil and water samples of a polluted area

A method for the analyses of pyridine in environmental samples is described. For soil samples a distillation procedure followed by an extraction, an acidic extraction or a Soxhlet extraction can be used. For water samples a distillation procedure followed by extraction can be employed. Deuterated pyridine is used as an internal standard and the extracts are analyzed by GC-MS. The recoveries of the methods are higher than 80%; the detection limits for pyridine are 0.01 mg/kg for soil samples and 0.2 g/l for water samples.     

Hemimicelle capped functionalized carbon nanotubes-based nanosized solid-phase extraction of arsenic from environmental water samples

The end functionalization of CNTs can introduce oxygen-containing negatively functional groups such as -COOH, -OH, or -CO on their surface site. If cationic surfactant such as cetyltrimethylammonium chloride (CTAC) was added to the functionalized CNTs, then interactions such as hydrophobic and ionic may lead to formation of hemimicelle/admicelle aggregates on the CNTs, a new kind of adsorbents, namely, the hemimicelle capped CMMWCNTs, is obtained. The application of the hemimicelle capped carbon nanotubes-based nanosized solid-phase extraction (SPE) adsorbents in environmental analysis is reported for the first time using arsenic as model target. The effect of adsorption and desorption conditions for arsenic including the amount of surfactant, initial pH of sample solution, the ultrasonic time of sample solution, the amount of electrolyte, flow rate, eluent and its amount were investigated and optimized prior to its determination by atomic fluorescence spectrophotometry (AFS). Arsenic can be quantitatively retained on the hemimicelle capped CMMWCNTs at pH 5-6 from sample volume up to 500 mL and then eluted completely with 2 mol L⁻¹ HNO₃ in the presence of 10 mg L⁻¹ CTAC. The method detection limit for arsenic determination with AFS detection was 2 ng L⁻¹, and the relative standard deviation (RSD, n = 11) was 5.3% at the 0.5 μg L⁻¹ level. The recoveries of arsenic in the spiked environmental water samples ranged from 94% to 104.29% with 500 mL of water sample. The proposed method has been applied successfully to the analysis of arsenic in aqueous environmental samples, which demonstrates the hemimicelle capped CMMWCNTs can be an excellent SPE adsorbents for arsenic pretreatment and enrichment from real water samples.     

Continuous-flow determination of reducing sugars in serum by reaction with periodate ions,with use of a flow-through periodate-sensitive electrode

A continuous-flow method for the determination of reducing sugars in serum is described. The sample reacts with an excess of periodate in a flow system and the decrease in periodate

activity is monitored with a periodate-sensitive flow-through electrode. The recorded potential peak heights are indirectly linearly related to the reducing sugar concentration expressed as glucose, in the range 50–290 mg/100 ml. The analysis is completely automated and requires no sample pretreatment, and samples can be analyzed at the rate of 30 per hour with average errors and relative standard deviation of about 1–2%. Comparison with an enzymatic method for serum gave satisfactory results.     

High-Throughput Analysis of Sofalcone in Human Plasma by Use of Automated 96-Well Protein Precipitation and LC-MS-MS

A sensitive and selective method for the determination of sofalcone in human plasma was established by use of protein precipitation and liquid chromatography-tandem mass spectrometry. Plasma samples were transferred into 96-well plate using an automated sample handling system and spiked with 10 L of 2 g mL^–1 internal standard solution (d₃-sofalcone). 0.5 mL of acetonitrile was added to the 96-well plate and the plasma samples were then vortexed for 30 sec. After centrifugation, the supernatant was transferred into another 96-well plate and completely evaporated at 40 °C under a stream of nitrogen. The dry residue was reconstituted with mobile phase. All sample transfer and protein precipitation was automated through the application of both the PerkinElmer MultiPROBE II HT and TOMTEC Quadra 96 workstation. The limit of quantitation of sofalcone was 2 ng mL^–1 using a sample volume of 0.2 mL for the analysis. The reproducibility of the method was evaluated by analyzing five samples at nine quality control (QC) levels over the nominal concentration range from 2 ng mL^–1 to 1000 ng mL^–1. Validation of the method showed that the assay has good precision and accuracy. Sofalcone and internal standard produced a protonated precursor ion ([M+H]⁺) at m/z 451 and 454, and both gave a corresponding product ion at m/z 315. The high sample throughput of the method has been successfully applied to a pharmacokinetic study of sofalcone in human plasma.     

On-line column preconcentration for the determination of cobalt in sea water by flow-injection chemiluminescence detection

A flow-injection method for the determination of dissolved cobalt(II) in sea water has been studied based on a combination of column preconcentration using 8-quinolinol immobilized on silica gel, fluoride containing metal alkoxide glass (8HQ-MAF) and chemiluminescence detection with a gallic acid-hydrogen peroxide system. Co(II) is selectively recovered from an acidified sample with 8-quinolinol immobilized on silica gel. After elution with dilute hydrochloric acid the resultant eluent is mixed with the reagent solutions, heated to 60^°C and then introduced into the CL cell. The analysis time including the 2-min sample load was 8 min per sea water sample with a corresponding detection limit of 0.62 ngl^-1 (3). The average standard deviation calculated for 10 replicate measurements of artificial sea water samples with a concentration of 10 ngl^-1 cobalt was ±2.1%. The method has been tested with the standard reference sea waters NASS and CASS.     

Determining urea levels in dialysis human serum by means of headspace solid phase microextraction coupled with ion mobility spectrometry and on the basis of nanostructured polypyrrole film

A simple and sensitive headspace (HS) solid phase microextraction (SPME) coupled with ion mobility spectrometry (IMS) method is presented for analysis of urea in dialysis human serum samples. A dodecylbenzenesulfonate-doped polypyrrole coating was used as a fiber for SPME. The HS-SPME–IMS method exhibits good repeatability (relative standard deviation of 3 % or less), simplicity, and good sensitivity. The influence of various analytical parameters such as pH, ionic strength, extraction time and temperature was investigated and the parameters were optimized. The calibration graph was linear in the range from 5 to 50 μg mL^?1, and the detection limit was 2 μg mL^?1. The method was applied successfully for determination of urea in human serum and with acceptable recovery (more than 98 %). Finally, a standard addition calibration method was applied to the HS-SPME-IMS method for the analysis of human serum samples before and at the end of dialysis. The proposed method appears to be suitable for the analysis of urea in serum samples as it is not time-consuming and requires only small quantities of the sample without any derivatization process.