紫外光辐照下以PAMAM树形分子为模板制备Ag纳米簇及光致发光性能研究

以G5.0-OH PAMAM树形分子为模板,用紫外光辐照法制备银纳米簇.用透射电子显微镜、紫外-可见吸收光谱和共振散射光谱等对所制备的银纳米簇进行了表征.结果表明:用紫外光辐照法可以制备尺寸分布均匀、稳定的银纳米簇;且辐照时间、PAMAM树形分子的浓度及Ag⁺/PAMAM树形分子的摩尔比都会对所制备的银纳米簇产生较大的影响.由于所制备的银纳米簇的粒径小于树形分子的流体力学半径,表明树形分子起到了“内模板”作用.同时研究了银纳米簇的尺寸对其光致发光性能的影响,发现通过调节银纳米簇的尺寸可实现其光致发光的可调性.     

PAMAM树形分子与Cd2＋的配位作用研究及CdS/PAMAM纳米复合材料的制备与表征

CdS半导体纳米簇具有独特的光、电性能, 如何制备均匀分散的、能够稳定存在的CdS纳米簇是目前的研究热点之一. 以聚酰胺-胺(PAMAM)树形分子为模板, 原位合成了CdS纳米簇. 首先用UV-Vis分光光度法研究了与树形分子的配位机理, 得出G4.5和G5.0的平均饱和配位数分别为16和34, 并发现在G4.5PAMAM树形分子中Cd^2＋主要与最外层叔胺基配位, 在G5.0PAMAM树形分子中Cd^2＋主要与最外层伯胺基配位. 酯端基的G4.5的模板作用要明显优于胺端基的G5.0. 通过改变Cd^2＋与G4.5树形分子的摩尔比可以得到不同粒径的CdS纳米簇. 溶液的pH值对CdS纳米簇影响很大, pH在7.0左右制备的CdS纳米簇粒径小而均匀, 且溶液稳定性高. 用UV-Vis分光光度计和TEM对CdS纳米簇的大小和形貌进行了表征. 结果表明TEM观测CdS纳米簇的粒径要大于用Brus公式的估算值.     

PAMAM树形分子与Cd2＋的配位作用研究及CdS/PAMAM纳米复合材料的制备与表征

CdS半导体纳米簇具有独特的光、电性能, 如何制备均匀分散的、能够稳定存在的CdS纳米簇是目前的研究热点之一. 以聚酰胺-胺(PAMAM)树形分子为模板, 原位合成了CdS纳米簇. 首先用UV-Vis分光光度法研究了与树形分子的配位机理, 得出G4.5和G5.0的平均饱和配位数分别为16和34, 并发现在G4.5PAMAM树形分子中Cd^2＋主要与最外层叔胺基配位, 在G5.0PAMAM树形分子中Cd^2＋主要与最外层伯胺基配位. 酯端基的G4.5的模板作用要明显优于胺端基的G5.0. 通过改变Cd^2＋与G4.5树形分子的摩尔比可以得到不同粒径的CdS纳米簇. 溶液的pH值对CdS纳米簇影响很大, pH在7.0左右制备的CdS纳米簇粒径小而均匀, 且溶液稳定性高. 用UV-Vis分光光度计和TEM对CdS纳米簇的大小和形貌进行了表征. 结果表明TEM观测CdS纳米簇的粒径要大于用Brus公式的估算值.     

以PAMAM树形分子为模板制备Pd纳米簇合物

以酯端基聚酰胺-胺树形分子(PAMAM)为模板在甲醇溶剂中制备了Pd纳米簇合物. 采用紫外-可见分光光度法和红外光谱法研究了Pd²⁺与树形分子的作用机理, 结果表明, Pd²⁺与树形分子内部胺基基团(主要为叔胺基)产生了络合作用. 采用硼氢化钠还原法制备了树形分子包裹的、粒径为2 nm的球形面心立方Pd纳米簇合物. 紫外-可见吸收光谱研究结果表明, Pd²⁺与树形分子的摩尔比越小, 生成的纳米簇合物尺寸越小; 由于高代数树形分子具有封闭结构, 且其内部配体数目较多, 采用较高代数的树形分子(5.5代)比低代数(3.5代)更有利于得到尺寸小、分散性较好的Pd纳米簇合物.     

AgBr纳米簇：PAMAM树形分子模板法制备及光催化性能研究

以酯端基聚酰胺-胺(PAMAM)树形分子为模板，原位制备了AgBr纳米簇。由于酯端基的半代PAMAM树形分子起到“内模板”作用，制得的AgBr纳米簇粒径小、尺寸分布窄、稳定性好，并通过改变Ag⁺∶PAMAM树形分子的物质的量的比可以精确控制纳米簇的尺寸。AgBr纳米簇/树形分子纳米复合材料在光催化降解甲基橙方面具有很好的催化能力，且随纳米簇的尺寸减小，其催化能力增强。     

聚酰胺-胺型树形分子模板法制备Pt纳米簇

利用紫外-可见吸收光谱和红外光谱对Pt2＋与G5.5-COOCH3聚酰胺-胺型树形分子的络合机理进行了研究, 结果表明Pt2＋与G5.5-COOCH3 PAMAM的最外层叔胺基发生络合作用, 但两者之间达到络合平衡需要较长时间, 且平衡时间随Pt2＋与树形分子物质的量比增大而增长; Pt2＋与G5.5-COOCH3树形分子的最大络合数为50～55; 采用硼氢化钠还原法原位制备了G5.5-COOCH3 PAMAM包裹、平均粒径小于2 nm、多晶的球形Pt纳米簇, 并研究了Pt2＋与PAMAM物质的量比对Pt纳米簇形貌的影响, 实验结果表明, Pt2＋与PAMAM物质的量比为10时, 生成尺寸较小分布较窄的内型Pt纳米簇/树形分子复合材料, 而物质的量比为50时, 会生成部分尺寸较大、分布较宽的外型Pt纳米簇/树形分子纳米复合材料.     

温度对聚酰胺-胺树形分子模板法制备CdS量子点的影响

为了研究温度对聚酰胺-胺(PAMAM)树形分子的模板法制备硫化镉(CdS)量子点的影响, 以4.5代(G4.5, 64个甲酯端基)PAMAM树形分子为模板, 在－10～30 ℃的温度范围内制备了分散良好的CdS量子点. 用透射电子显微镜(TEM)表征了CdS量子点的形貌、尺寸; 用紫外-可见光谱(UV-Vis)和光致发光光谱(PL)表征了CdS量子点的光学性能. 发现在相同条件下, 制备温度从－10 ℃升高到30 ℃, CdS量子点粒径从1.8 nm增大到3.4 nm, 其中在10 ℃时制备的量子点的尺寸分布最窄; CdS量子点的吸收和发射光谱均随温度增大而红移, 其中10 ℃时制备的量子点的室温光致发光效率最高. 这表明制备温度决定了树形分子的配位基团与Cd^2＋的分离速度, 并影响了CdS量子点的成核和生长过程, 从而最终决定了CdS量子点的尺寸及尺寸分布、光致发光颜色和发光效率.     

高分子模板对CdS量子点制备及其光催化性能的影响

分别以球形聚酰胺-胺(PAMAM)树形分子和线形聚乙烯吡咯烷酮(PVP)两种结构不同的高分子为模板, 原位制备了分散良好的CdS量子点(CdS QDs), 并以甲基橙为降解对象, 研究了高分子模板结构对CdS量子点的制备和光催化性能的影响. 结果表明, 以PAMAM 树形分子为模板制备的CdS量子点(CdS QDs/PAMAM)比以PVP为模板制备的CdS量子点(CdS QDs/PVP)的尺寸分布更窄, 激子吸收峰更明显, 光致发光(PL)强度更高|并且在量子点尺寸接近的情况下, CdS QDs/PAMAM的催化效率明显高于CdS QDs/PVP. 这是由于PAMAM树形分子独特的结构有利于生成尺寸均匀的CdS量子点, 且不易钝化量子点表面的活性位点|而线性的PVP分子量分布较宽, 使制备的量子点的尺寸分布较宽, 且PVP分子链缠绕在CdS量子点表面, 钝化了部分活性位点, 降低催化效率. 此外, CdS QDs/PAMAM的催化能力随粒径减小而增大.     

Ag+/Ag/ZnO多孔纳米结构纤维材料的制备及可见光催化性能

借助棉花纤维模板, 采用两步法制备了Ag⁺/Ag/ZnO多孔纳米结构纤维材料, 并利用X射线衍射(XRD)、 X射线光电子能谱(XPS)、 扫描电子显微镜(SEM)和紫外-可见光谱(UV-Vis)等对其进行了表征. 以亚甲基蓝(MB)的脱色降解为模型反应, 考察了银修饰量(摩尔分数, 0~1.50%)对ZnO纳米结构纤维材料光催化性能的影响. 结果表明, 利用模板辅助的两步法制备了Ag⁺-Ag共修饰的ZnO多孔纳米结构纤维材料Ag⁺/Ag/ZnO, Ag⁺和Ag通过改变ZnO的晶胞结构、 光吸收特性及形貌等影响其光催化性能; 在可见光条件下, Ag⁺/Ag/ZnO的催化性能优于纯ZnO, 且与修饰量有关.     

DNA银纳米簇在功能核酸荧光生物传感器中的应用

DNA银纳米簇(DNA-AgNCs)是以DNA为模板, 通过碱基杂环上的N原子与Ag⁺结合, 用NaBH₄将Ag⁺还原得到的具有荧光性质的新兴纳米探针. 由于DNA-AgNCs具有合成方法简单、 生物相容性好和荧光发射波长可调等优点, 使其在分析检测等领域具有广泛的应用. 本文对DNA-AgNCs的合成和荧光性质两个方面进行了综述, 分类总结了以DNA-AgNCs为无标记荧光探针在功能核酸荧光生物传感器方面的应用, 对其不足与应用潜力进行展望, 以期为未来的研究与应用提供借鉴.     

Morphological change of gold-dendrimer nanocomposites by laser irradiation

Gold-dendrimer nanocomposites are prepared in aqueous solutions in the presence of poly(amidoamine)dendrimers (PAMAM) (generation 3 and 5) or poly(propyleneimine)dendrimers (PPI) (generation 3 and 4) by wet chemical NaBH(4) method. Thus prepared gold-dendrimer nanocomposites are irradiated by laser at 532 nm. UV-vis absorption spectroscopy and transmission electron microscopy reveal that the gold nanoparticles grow with the laser irradiation time as well as the fluence of the laser; in particular, the gold nanoparticles prepared at lower concentrations of PAMAM dendrimer as well as lower generations of PAMAM grow significantly. On the other hand, in the case of PPI dendrimers, the gold nanoparticles hardly grow by irradiation. In addition, dynamic light-scattering measurements show that the laser irradiation markedly promotes the association of the gold-PAMAM G3 dendrimer nanocomposites compared to that of the gold-PAMAM G5 dendrimer nanocomposites, while the sizes of association for the gold-PPI G3, G4 dendrimer nanocomposites hardly change by laser irradiation.     

Comparison of PAMAM-Au and PPI-Au nanocomposites and their catalytic activity for reduction of 4-nitrophenol

Dendrimer-Au nanocomposites are prepared in aqueous solutions using poly(amidoammine)dendrimers (PAMAM) (generation 2, 3, and 5) and poly(propyleneimine)dendrimers (PPI)(generation 2, 3, and 4) by wet chemical NaBH(4) method. The Au nanoparticles thus obtained are 2-4 nm in diameter for both dendrimers and no generation dependence on the particle size is observed, whereas the generations of the dendrimers are increased as stabilization of Au-nanoparticles is achieved with lower dendrimer concentrations. Studies of the reduction reaction of 4-nitrophenol using these nanocomposites show that the rate constants for the PAMAM dendrimers (generations 2 and 3) are higher than those for the PPI dendrimers (generations 2 and 3), while a distinct difference in the rate constants is not seen for the PAMAM dendrimer (generation 5) or the PPI dendrimer (generation 4). In addition, the rate constants for the reduction of 4-nitrophenol involving all the dendrimers decrease with increases in dendrimer concentrations.     

Preparation of PAMAM- and PPI-metal (silver, platinum, and palladium) nanocomposites and their catalytic activities for reduction of 4-nitrophenol

Dendrimer-metal (silver, platinum, and palladium) nanocomposites are prepared in aqueous solutions containing poly(amidoamine) (PAMAM) dendrimers with surface amino groups (generations 3, 4, and 5) or poly(propyleneimine) (PPI) dendrimers with surface amino groups (generations 2, 3, and 4). The particle sizes of the metal nanoparticles obtained are almost independent of the generation as well as the concentration of the dendrimer for both the PAMAM and the PPI dendrimers; the average sizes of silver, platinum, and palladium nanoparticles are 5.6-7.5, 1.2-1.6, and 1.6-2.0 nm, respectively. It is suggested that the dendrimer-metal nanocomposites are formed by adsorbing the dendrimers on the metal nanoparticles. Studies of the reduction reaction of 4-nitrophenol by these nanocomposites show that the rate constants are very similar between PAMAM and PPI dendrimer-silver nanocomposites, whereas the rate constants for the PPI dendrimer-platinum and -palladium nanocomposites are greater than those for the corresponding PAMAM dendrimer nanocomposites. In addition, it is found that the rate constants for the reduction of 4-nitrophenol involving all the dendrimer-metal nanocomposites decrease with an increase in the dendrimer concentrations, and the catalytic activity of dendrimer-palladium nanocomposites is highest.     

磁性Fe_3O_4@PS@PAMAM-Ag复合催化粒子的制备及其可再生催化性能(英文)

采用聚苯乙烯(PS)包裹Fe3O4磁性纳米粒子,制得Fe3O4@PS复合微球,以此作为磁性载体,通过微球表面的羧基将聚酰胺-胺类树形大分子(PAMAM)连接到磁性载体上,然后使Ag纳米粒子镶嵌在树形分子层中,制得可再生的金属复合催化粒子Fe3O4@PS@PAMAM-Ag.并采用红外光谱、扫描电镜、电感耦合等离子体质谱(ICP-MS)和X射线光电子能谱等方法对复合催化粒子进行了表征,结果表明,树形分子可以较好地分散和稳定金属Ag纳米粒子,所制复合催化粒子表面Ag含量为1.64%,具有较高的催化还原对硝基苯酚的活性.同时,利用外加磁场可以方便快捷地从反应体系中分离出来,继续用于下一次反应中,复合催化粒子循环使用6次后,仍保持完全的催化性能.     

低代端酯基PAMAM树形分子存在下银纳米颗粒的制备

在低代端酯基PAMAM树形分子(G1.5-COOCH₃)存在时，用氢气还原AgNO₃制备出银纳米颗粒。用透射电子显微镜(TEM)，电子衍射(ED)，紫外-可见吸收光谱(UV-Vis)和红外光谱(FT-IR)对所制备的银纳米颗粒进行了表征。实验结果表明，当用氢气作为还原剂时，以低代树形分子为保护剂，通过优化还原条件，可成功制备尺寸稳定、均一的银纳米颗粒，其粒径为2.9±0.5 nm，且所制备的银纳米颗粒的粒径分布较窄。根据树形分子的理论尺寸与制备的银纳米颗粒的粒径关系，可推断出大多数的银纳米颗粒是由多个树形分子所包围而稳定存在。     

Scavenging DPPH radicals catalyzed by binary noble metal-dendrimer nanocomposites

Catalytic activity of gold-platinum, gold-palladium, and platinum-palladium dendrimer nanocomposites for scavenging 1,1-diphenyl-2-picrylhydrazyl (DPPH) radicals was investigated. The gold-platinum and gold-palladium dendrimer nanocomposites were prepared via simultaneous reduction by sodium borohydride in the presence of poly(amidoamine) (PAMAM) dendrimers with amine or carboxyl terminal groups. The particles were not mixtures of monometallic particles but alloyed bimetallic particles. Bimetallic particles exhibited higher catalytic activity than monometallic ones.     

Investigation of thermal behaviour of hybrid nanostructures based on Fe2O3 and PAMAM dendrimers

Dendrimers or biofunctionalized dendrimers can be assembled onto magnetic iron oxide nanoparticles to stabilize or functionalize inorganic nanoparticles. Carboxylated poly(amidoamine) PAMAM dendrimers (generation 4.5) have been used for the synthesis of iron oxide nanoparticles, resulting nanocomposites with potential biomedical applications. The present paper aims to systematically investigate the thermal behaviour of nanostructured hybrids based on ferric oxide and PAMAM dendrimers, by differential scanning calorimetry (DSC) technique. The novelty consists both in synthesis procedure of hybrid nanostructures as well as in DSC approach of these nanocomposites. For the first time, we propose a new method to prepare Fe₂O₃??dendrimer nanocomposite, using soft chemical process at high pressure. Commercial PAMAM dendrimers with carboxylic groups on its surface were used. When high pressure is applied, polymeric structures suffer morphological changes leading to hybrid nanostructures' formation. In the same time, crystallinity of inorganic nanoparticles is provided. DSC results showed an increase in thermal stability of composites as compared to commercial dendrimers. This could be due to the formation of strong interactions between ferric oxide and carboxyl groups, as confirmed by Fourier transform infrared spectroscopy. Electron microscopy analysis (SEM/EDX) and size measurements were performed to demonstrate the existence of nanosized particles.