Determination of tellurium at ultra-trace levels in drinking water by on-line solid phase extraction coupled to graphite furnace atomic absorption spectrometer

In this paper, two time-based flow injection (FI) separation pre-concentration systems coupled to graphite furnace atomic absorption spectrometry (GFAAS) for tellurium determination are studied and compared. The first alternative involves the pre-concentration of the analyte onto Dowex 1X8 employed as packaging material of a micro-column inserted in the flow system. The second set-up is based on the co-precipitation of tellurium with La(OH)₃ followed by retention onto XAD resins. Both systems are compared in terms of limit of detection, linear range, RSD%, sample throughput, micro-columns lifetime and aptitude for fully automatic operation.     

On-line sample-pre-treatment schemes for trace-level determinations of metals by coupling flow injection or sequential injection with ICP-MS

Within the last decade, the first generation of flow injection (FI) has been supplemented by sequential injection (SI), also termed the second generation, and, recently, by the third generation, i.e., SI-Lab-on-Valve (SI-LOV). As apparent from the literature, FI and/or SI have become dominant as substitutes for labor-intensive, manual, sample-pre-treatment and/or solution-handling procedures prior to analyte detection by inductively coupled plasma mass spectrometry (ICP-MS). The present review presents and discusses the progress of the state of the art in implementing miniaturized FI/SI systems for on-line matrix separation and pre-concentration of trace levels of metals with detection by ICP-MS. It highlights some of the frequently applied on-line, sample-pre-treatment schemes, including solid phase extraction (SPE), on-wall molecular sorption and precipitate/(co)-precipitate retention using a polytetrafluoroethylene (PTFE) knotted reactor (KR), solvent extraction-back extraction and hydride/vapor generation. It also addresses a novel, robust approach, whereby the protocol of SI-LOV-bead injection (BI) on-line separation and pre-concentration of ultra-trace levels of metals by a renewable microcolumn is interfaced to ICP-MS, as conducted in the present authors' group. It discusses the future outlook in this field.     

Multi‐Walled Carbon Nanotubes as Sorbent for Flow Injection On‐Line Microcolumn Preconcentration Coupled with Flame Atomic Absorption Spectrometry for Determination of Cadmium and Copper

Abstract

Multi‐walled carbon nanotubes (MWNTs) were used as sorbent for flow injection (FI) on‐line microcolumn preconcentration coupled with flame atomic absorption spectrometry (FAAS) for determination of trace cadmium and copper in environmental and biological samples. Effective preconcentration of trace cadmium and copper was achieved in a pH range of 4.5–6.5 and 5.0–7.5, respectively. The retained cadmium and copper were efficiently eluted with 0.5 mol L^?1 HCl for on‐line FAAS determination. The MWNTs packed microcolumn exhibited fairly fast kinetics for the adsorption of cadmium and copper, permitting the use of high sample flow rates up to at least 7.8 mL min^?1 for the FI on‐line microcolumn preconcentration system without loss of the retention efficiency. With a preconcentration time of 60 sec at a sample loading flow rate of 4.3 mL min^?1, the enhancement factor was 24 for cadmium and 25 for copper at a sample throughput of 45 h^?1. The detection limits (3σ) were 0.30 and 0.11 µg L^?1 for Cd and Cu, respectively. The precision (RSD) for 11 replicate measurements was 2.1% at the 10‐µg L^?1 Cd level and 2.4% at the 10‐µg L^?1 Cu level. The developed method was successfully applied to the determination of trace Cd and Cu in a variety of environmental and biological samples.     

On-line flow injection solvent extraction for electrothermal atomic absorption spectrometry: Determination of nickel in biological samples

A flow injection (FI) on-line solvent extraction system for electrothermal atomic absorption spectrometry (ETAAS) was developed with nickel as a model trace element. The nickel pyrrolidine-dithiocarbamate chelate was extracted on line into isobutyl methyl ketone, which was delivered into the FI system by a peristaltic pump equipped with poly(tetrafluoroethylene) tubing. The organic phase was separated from the aqueous phase by a novel gravity phase separator with a small conical cavity, and stored in a collector tube, from which 50 μl organic concentrate was introduced into the graphite tube by an air flow. ETAAS determination of the analyte was performed in parallel with the extraction process. An enrichment factor of 25 was obtained in comparison with 50 μl direct introduction while achieving a detection limit of 4 ng l⁻¹ (3σ), and a precision of 1.5% relative standard deviation for 1.0 μg l⁻¹ nickel (n = 11). The proposed method was successfully applied to the determination of nickel in body fluids and other biological samples.     

Simultaneous determination of seven metal ions in water samples by solid-phase extraction on polyacrylonitrile activated carbon fibres

A new solid-phase extraction method utilising polyacrylonitrile activated carbon fibres (PAN-ACFs) as adsorbent was developed for the preconcentration of trace metal ions prior to their determination by inductively coupled plasma optical emission spectrometry (ICP-OES). The PAN-ACFs oxidised with nitric acid were characterised by FT-IR, XRD, SEM and BET analysis. Then the resulting PAN-ACFs were used as solid-phase adsorbent for simultaneously determination of trace Al(III), Be(II), Bi(III), Cr(III), Cu(II), Fe(III) and Pb(II) ions in aqueous solutions. The influences of the analytical parameters on the recoveries of the studied ions were investigated. The optimum experimental conditions of the proposed method were pH: 6.0; eluent concentration and volume: 3.0 mL of 1.5 mol L^?1 nitric acid; flow rates of sample and eluent solution: 1.5 mL min^?1. The preconcentration factors were found to be 67 for Al(III), Bi(III); 83 for Cr(III), Cu(II), Fe(III) and 50 for Be(II), Pb(II). The precision of this method was in range of 1.5%~3.5% and the detection limit of this metal ions was between 0.06~1.50 μg L^?1. The developed method was validated by the analysis of a certified reference sample and successfully applied to the determination of trace metal ions in water samples with satisfactory results.     

Electrothermal Vaporization of Trace Gallium via In SITU Alkylation for Inductively Coupled Plasma Atomic Emission Spectrometry

Abstract

A sample introduction method based on alkylation of the analyte was proposed for introducing trace gallium into inductively coupled plasma for atomic emission spectrometry. By using 10 μl of a sample solution with 15 μl of a 0.9 mol 1^-1 solution of ethylmagnesium bromide in tetrahydrofuran as alkylating reagent, a detection limit of 1.9 ng of gallium was obtained and the calibration graph was linear with the amount of gallium up to 100 ng. The relative standard deviation (n = 10) was 2.0% when 10 ng of gallium was present in the sample.     

纳流液相分离与电感耦合等离子体质谱联用技术研究新进展

高效微纳液相分离技术如纳流液相色谱、毛细管电泳、微芯片色谱/电泳等与电感耦合等离子体质谱（ICP-MS）检测技术联用，既具有前端分离技术高选择性、高灵敏度、快速、低样品消耗的特点，又结合了后端ICP-MS检测分辨率高、动态范围宽、可绝对定量等优势，正在发展成为一种重要的高内涵联用分析手段。该文对近年来纳流液相分离与ICP-MS联用装置的发展作一系统介绍，对其在化学与生物化学分析等领域的应用予以综述，并展望了该联用技术的发展前景。     

高压微波消解-电感耦合等离子体原子发射光谱同时测定进口奶粉中Fe、Zn、Ca、Mg、Cu含量

通过优化试验确定仪器的最佳工作参数,硝酸-过氧化氢微波消解样品,采用电感耦合等离子体原子发射光谱同时测定进口奶粉中的Fe、Zn、Ca、Mg、Cu多种金属元素含量．试验过程方便快捷,多种元素同时测定节约测定时间．方法的准确度、精密度均符合日常检验的需要．     

Determination of trace elements in human serum by inductively coupled plasma atomic emission spectrometry with flow injection

An analytical method for the simultaneous determination of some trace elements (Au, Fe, Mg, Li, Sr, Zn) in human serum by inductively coupled plasma atomic emission spectrometry (ICP-AES) with flow injection is described. Physical interference caused by the change of sample viscosity is discussed. When 100 μl of serum was injected, the relevant recoveries of > 99% for Li, > 98% for Cu and Mg, > 95% for Fe were obtained for an NIST SRM with R.S.D. > 1.3% using optimized flow injection parameters. The prepared lyophilized control serum for routine analysis in clinical laboratories was analyzed and verified for the validity of the technique employed in this experiment using NIST SRM 909 as a primary reference material.     

Determination of Hg(II) in Environmental Water Samples by Dispersive Liquid Phase Microextraction Combined with Flame Atomic Absorption Spectrometry

In this study, a method of dispersive liquid phase microextraction combined with the flame atomic absorption spectrometry was proposed for the determination of trace Hg using diphenylthiocarbazone as chelating reagent. Several factors which have effect on the microextraction efficiency of Hg, such as pH, extraction and dispersive solvent type and their volume, concentration of the chelating agent, extraction time were investigated, and the optimized experimental conditions were established. After extraction, the enrichment factor was 68. The detection limit of the method was 45 ng mL^?1, and the relative standard deviation for eight determinations of 2 μg mL^?1 Hg was 1.7%. The results for the determination of Hg in environmental water samples (tap water, well water, mineral water and Caspian sea water) have demonstrated the applicability of the proposed method.     

Elemental Analysis of Biodiesel by Inductively Coupled Plasma Optical Emission and Flame Atomic Absorption Spectrometries

The extraction of 21 elements from biodiesel using aqueous acid and alkaline solutions was investigated as pretreatment to permit their determination by inductively coupled plasma optical emission spectrometry and flame atomic absorption spectrometry. Al, Ca, Cd, Cu, K, Mg, Mn, Na, V, and Zn were completely extracted from the biodiesel fuel with aqueous acid solution, and Na was completely extracted with alkaline solution. Extraction characteristics varied from element to element; however, 100?±?5% recoveries were obtained with a 30-s extraction procedure. Therefore, although biodiesel is an organic lipophilic material, these elements were determined in aqueous solution. The extracted elements were determined based on traceable Japan calibration service system standards. Accurate analysis of biodiesel was performed using the reported protocol.     

Liquid-phase microextraction combined with graphite furnace atomic absorption spectrometry: A review

An overview of the combination of liquid-phase microextraction (LPME) techniques with graphite furnace atomic absorption spectrometry (GFAAS) is reported herein. The high sensitivity of GFAAS is significantly enhanced by its association with a variety of miniaturized solvent extraction approaches. LPME-GFAAS thus represents a powerful combination for determination of metals, metalloids and organometallic compounds at (ultra)trace level. Different LPME modes used with GFAAS are briefly described, and the experimental parameters that show an impact in those microextraction processes are discussed. Special attention is paid to those parameters affecting GFAAS analysis. Main issues found when coupling LPME and GFAAS, as well as those strategies reported in the literature to solve them, are summarized. Relevant applications published on the topic so far are included.     

流动注射在线富集-FAAS测定合金钢中微量镍

提出了流动注射在线离子交换富集-火焰原子吸收光谱法测定合金钢中微量镍的分析方法.在线离子交换采用双柱正向富集和反向洗脱流路方式,使用80目732强酸型阳离子交换树脂在酸度为0.10mol/L HCl中富集样品中的Ni2+,并用2.0mol/L HCl洗脱.设计了流动注射在线离子交换富集双柱流路的操作程序,优化了各项仪器...     

Ionic liquid-based dispersive liquid–liquid microextraction for the separation and preconcentration of lead in water samples prior to FAAS determination without chelating agent

In the present study, an environment-friendly sample preparation method termed ionic liquid-based dispersive liquid–liquid microextraction combined with flame atomic absorption spectrometry has been developed for the determination of Pb(II) ion in water samples prior to flame atomic absorption spectrometry determination. In this method, ionic liquid was used as an extraction solvent instead of the organic solvent used in the conventional dispersive liquid–liquid microextraction (DLLME) assay, and there is no need for a chelating agent. Several variables that may affect extraction efficiencies, including pH, the volume of ionic liquid, the type and volume of disperser solvent, salt addition, and the time for centrifugation and extraction were studied and optimised. Under the optimised conditions, the calibration curve exhibited linearity over the range of 20.0–1000.0 μg L^?1. The enrichment factor and the limit of detection based on 3S_b/m were 35.0 and 5.9 μg L^?1, respectively. Seven replicate determination of a solution containing of 100.0 μg L^?1 Pb(II) ions gave a relative standard deviation of ±2.1%. Finally, the feasibility of the proposed method for Pb(II) determination was assessed by the analysis of certi?ed reference material and various water samples and the satisfactory results were obtained.     

Hollow fiber supported liquid membrane microextraction of Cu2+ followed by flame atomic absorption spectroscopy determination

Hollow fiber supported liquid membrane microextraction, a relatively new sample preparation technique, has attracted much interest in the field of environmental analysis. In the current study, a novel method based on hollow-fiber liquid-phase microextraction and flame atomic absorption spectrometry (FAAS) for the measurement of copper ion in aqueous samples is described. Hollow-fiber liquid-phase microextraction conditions such as the type of extraction solvent, pH, the stirring rate, and the amounts of chelating agents, sample volume, and the extraction time were investigated. Under the optimized conditions, the linear range was found to be 0.01–15 μg ml^?1 for copper ion, and the limit of detection to be 0.004 μg ml^?1. Tap water and surface water samples collected from Mashhad, Iran and Dorongar river; Khorasan, Iran, respectively, were successfully analyzed using the proposed method. The recoveries from the spiked water samples were 72.4% and 105%, respectively; and the relative standard deviation (RSD) at the 2 μg ml^?1 level was 6%.     

基于吸力洗脱的流动注射在线富集与火焰原子吸收联用测定水样中的镉

建立了一种基于吸力洗脱的流动注射(FI)在线富集与火焰原子吸收光谱法(FAAS)联用测定水样中痕量镉的新方法.洗脱过程依靠蠕动泵的吸力而不是推力实现洗脱剂的输送,明显降低了被分析物在洗脱过程中的分散,提高了原子吸收信号峰值(A),同时提高了富集系数(EF).进样流速6.0 mL/min;进样时间60 s,测定20 μg/L Cd2+,EF由传统方法的15提高到38;检出限为0.29 μg/L;测样频率为40个/h;相对标准偏差(RSD,n=11)为2.5%.以01‰ (V/V)的三乙醇胺(TEA)为掩蔽剂,Cd2+在水样中的回收率为93.8%～98.5%.     

流动注射-电感耦合等离子体质谱法的基体效应

研究了流动注射小体积进样,电感耦合等离子体质谱法的在体效应,并与连续进样作了比较,流动注射小体积（１００μＬ）进样时,电离电位较高的Ａｓ和Ａｕ基体对分析元素的信号表现为增强效应,分析元素的质量数越大,所受增强效应越小。了电位较低的Ｃｕ、Ｉｎ、Ｌｉ、Ｎａ和Ｐｂ基体对分析元素的信号则表为抑制效应,基体元素的质量数越大,对分析元素的抑制效应也越大;质量数较大的分析元素,所受的抑制效应较;对质量数相近的分析元素,电离电位较高者受的抑制较大,与连续进样相比,流动注射小体积进样时,基体元素对分析元素的抑制效应较弱,而增强效应较强。     

Cloud point extraction of aluminum (III) in water samples and determination by electrothermal atomic absorption spectrometry,flame atomic absorption spectrometry and UV-visible spectrophotometry

Cloud point extraction was applied as a preconcentration step for the determination of trace level of Al(III) in water samples with electrothermal atomic absorption spectrometry (ETAAS), flame atomic absorption spectrometry (FAAS) and UV-visible spectrophotometry. The aluminum was extracted as aluminum-Eriochrome Cyanine R (ECR) complex, at pH 6 by micelles of the non-ionic surfactant octylphenoxypolyethoxyethanol (Triton X-114). The investigations showed that the same CPE procedure can be used for different detection techniques. The results obtained from these techniques were evaluated. Under the optimal conditions, limit of detection obtained with ETAAS, FAAS and UV-visible spectrophotometry were 0.03 ng mL^?1, 0.06 µg mL^?1 and 0.01 µg mL^?1, respectively. The accuracy of the procedure was tested by analysing certified reference material. The method was successfully applied to determination of aluminum in water samples and dialysis fluid.     

Evaluation of ammonium fluoride for quantitative microwave-assisted extraction of silicon and boron from different solid samples

A novel, simple, efficient and environmentally friendly closed-microwave-assisted extraction (MAE) method of silicon and boron from a variety of industrial and environmental samples using ammonium fluoride as an extractant was developed. This method avoids handling the corrosive and toxic HF and prevents the potential risk of analyte loss due to the creation of volatile SiF₄ and BF₃ in the presence of HF. Atomic absorption spectrometry and inductively coupled plasma optical emission spectrometry were employed for the subsequent analysis of the resulting supernatant for determination of Si and B, respectively. Certified reference material BCR^®-032 Natural Moroccan Phosphate Rock (phosphate fertiliser) was taken to optimise the extraction parameters such as the sample amount, extraction temperature and time and the volume of the extractant. The optimum extraction parameters evaluated using a fractional factorial design were as follows: 50 mg of the sample extracted with 5 mL of 100 g L^?1 NH₄ F for 15 min at 180°C. The optimised MAE procedure was successfully applied to nine different matrix reference materials intended primarily for validation of methods for determination of components in fertilisers, sludge, plants and fly ash. The obtained results were in a good agreement with the certified or comparative values with an overall precision better than 10% in all cases. The proposed method is recommended for fast and reliable preparation of samples with silicon content <8.2% (w/w). However, further decreasing the sample mass to 10 mg enabled the quantitative extraction of silicon from fly ashes at levels of 23% (w/w).     

Ligandless,Task-Specific Ionic Liquid-Based Ultrasound-Assisted Dispersive Liquid–Liquid Microextraction for the Determination of Cobalt Ions by Electrothermal Atomic Absorption Spectrometry

Ligandless, task-specific ionic liquid based ultrasound-assisted dispersive liquid–liquid microextraction (TSIL-USA-DLLME) was used for preconcentration of cobalt ions in food and water samples and in vitamin supplements before analysis by electrothermal atomic absorption spectrometry. The reported method is free of toxic volatile organic solvents and does not require the use of a back-extraction step. The dispersion of extractant was achieved with the use of ultrasound. A TSIL, trioctylmethylammonium thiosalicylate (TOMATS), was served as both the extraction and complexing agent. After microextraction, the TOMATS phase was separated by centrifugation and dissolved in ethanol before analysis. Selected parameters affecting the microextraction including the pH of the sample, the volume of the ionic liquid, the ultrasonication time, centrifugation parameters, and the influence of ionic strength were optimized. The limit of detection was 0.011?ng?mL^?1 for cobalt ions. The achieved preconcentration factor was 24. The relative standard deviations for the determination of analyte in the real samples were 3–24%. The accuracy of this method was evaluated by the extraction and determination of the analyte in several certified reference materials including INCT-SBF-4 (soya bean flour), INCT-TL-1 (tea leaves), ERM-CAO11b (hard drinking water), INCT-MPH-2 (mixed Polish herbs), TMDA-54.5 (Lake Ontario Water), and NIST 1643e. The measured cobalt contents were in satisfactory agreement with the certified concentrations based on Student’s t-test at the 95% confidence level. The presented method has been successfully applied for the determination of analyte in real samples that include tea, lake water, and vitamin supplements.