Structure and magnetic properties of γ′-Fe4N films grown on MgO-buffered Si (0 0 1)

γ′-Fe₄N thin films were grown on MgO-buffered Si (1 0 0) by pulsed laser deposition technique. Different crystallographic orientations and in-plane magnetic anisotropies were achieved by varying the growth temperature of the MgO buffer layer. When the MgO buffer layer was grown at room temperature, the γ′-Fe₄N film shows isotropic in-plane magnetic properties without obvious texture; while in-plane magnetic anisotropy was recorded for the γ′-Fe₄N films deposited on a 600 °C-grown-MgO buffer due to the formation of a (1 0 0)-oriented biaxial texture. Such a difference in in-plane magnetic anisotropy is attributed to the epitaxial growth of γ′-Fe₄N film on an MgO buffer with relaxed strain when the MgO layer was grown at a high temperature of 600 °C.     

Thermal and irradiation induced interdiffusion in magnetite thin films grown on magnesium oxide (0 0 1) substrates

Epitaxial Fe₃O₄(0 0 1) thin films (with a thickness in the range of 10-20 nm) grown on MgO substrates were characterized using low-energy electron diffraction (LEED), conversion electron Mössbauer spectroscopy (CEMS) and investigated using Rutherford backscattering spectrometry (RBS), channeling (RBS-C) experiments and X-ray reflectometry (XRR). The Mg out-diffusion from the MgO substrate into the film was observed for the directly-deposited Fe₃O₄/MgO(0 0 1) films. For the Fe₃O₄/Fe/MgO(0 0 1) films, the Mg diffusion was prevented by the Fe layer and the surface layer is always a pure Fe₃O₄ layer. Annealing and ion beam mixing induced a very large interface zone having a spinel and/or wustite formula in the Fe₃O₄-on-Fe film system.     

Enhancement of L10 ordered FePt by Pt buffer layer

L₁₀-ordered FePt thin films prepared by molecular-beam epitaxy on MgO (0 0 1) substrate at 320 °C with different thickness of Pt buffer layer have been investigated. The out-of-plane coercivity increases with increasing thickness of Pt buffer. The maximum values of the long-range order parameter and uniaxial magnetic anisotropy energy are 0.72 and 1.78×10⁷ erg/cm³, respectively, for films with 12 nm thick Pt buffer layer, where the c/a ratio (0.976) shows the minimum value. The reason for the enhancement in ordering is due to the proper lattice strains Pt buffer bestows on FePt layer, these strains are equal to the contraction in lattice parameter c and the expansion in a. Studies of angular-dependent coercivity revealed that the magnetization reversal behaviour shifts from a domain-wall motion dominated case towards a near rotational mode with increasing thickness of Pt buffer layer.     

Microstructure and magnetic properties of nanocomposite FePt/MgO and FePt/Ag films

An in-plane magnetic anisotropy of FePt film is obtained in the MgO 5 nm/FePt t nm/MgO 5 nm films (where t=5, 10 and 20 nm). Both the in-plane coercivity (H_c∥) and the perpendicular magnetic anisotropy of FePt films are increased when introducing an Ag-capped layer instead of MgO-capped layer. An in-plane coercivity is 3154 Oe for the MgO 5 nm/FePt 10 nm/MgO 5 nm film, and it can be increased to 4846 Oe as a 5 nm Ag-capped layer instead of MgO-capped layer. The transmission electron microscopy (TEM)-energy disperse spectrum (EDS) analysis shows that the Ag mainly distributed at the grain boundary of FePt, that leads the increase of the grain boundary energy, which will enhance coercivity and perpendicular magnetic anisotropy of FePt film.     

Effect of microstructure of MgO buffer layer on BaTiO3 grown on silicon substrates

MgO ultrathin films were grown on Si(1 0 0) substrates as buffer layers for the growth of ferroelectric BaTiO₃ thin films by laser molecular beam epitaxy (L-MBE). The deposition process of MgO buffer layers grown on silicon was in situ monitored by reflection high-energy electron diffraction (RHEED). The structure of BaTiO₃ films fabricated on MgO buffers was investigated by X-ray diffraction. Biaxially textured MgO was obtained at high laser energy density, but when the laser energy was lowered, MgO buffer was transformed to the form of texture with angular dispersion with the increase of the film thickness. BaTiO₃ films grown on the former buffer were completely (0 0 1) textured, while those on the latter were (0 0 1) preferred orientated. Furthermore, the fabricated MgO buffers and BaTiO₃ films had atomically smooth surface and interface. All these can reveal that the quality of textured MgO buffer is a key factor for the growth of BaTiO₃ films on silicon.     

Growth of superconducting FeSe0.5Te0.5 thin films by pulsed-laser deposition

FeSe_0.5Te_0.5 thin films with PbO-type structure are successfully grown on MgO(1 0 0) and LaSrAlO₄(0 0 1) substrates from FeSe_0.5Te_0.5 or FeSe_0.5Te_0.75 polycrystalline targets by pulsed-laser deposition. The film deposited on the MgO substrate (film thickness ∼ 55 nm) shows superconductivity at 10.6 K (onset) and 9.2 K (zero resistivity). On the other hand, the film deposited on the LaSrAlO₄ substrate (film thickness ∼ 250 nm) exhibits superconductivity at 5.4 K (onset) and 2.7 K (zero resistivity). This suggests the strong influence of substrate materials and/or the c-axis length to superconducting properties of FeSe_0.5Te_0.5 thin films.     

Effect of nanoparticle size on magnetic damping parameter in Co92Zr8 soft magnetic films

Co₉₂Zr₈(50 nm)/Ag(x) soft magnetic films have been prepared on Si (111) substrates by oblique sputtering at 45°. Nanoparticle size of Co₉₂Zr₈ soft magnetic films can be tuned by thickening Ag buffer layer from 9 nm to 96 nm. The static and dynamic magnetic properties show great dependence on Ag buffer layer thickness. The coercivity and effective damping parameter of Co₉₂Zr₈ films increase with thickening Ag buffer layer. The intrinsic and extrinsic parts of damping were extracted from the effective damping parameter. For x=96 nm film, the extrinsic damping parameter is 0.028, which is significantly larger than 0.004 for x=9 nm film. The origin of the enhancement of extrinsic damping can be explained by increased inhomogeneity of anisotropy. Therefore, it is an effective method to tailor magnetic damping parameter of thin magnetic films, which is desirable for high frequency application.     

Enhanced ferroelectric property of (Pb0.95Ca0.05)(Nb0.02Zr0.80Ti0.20)O3 thin films prepared by RF magnetron sputtering

(Pb_0.95Ca_0.05)(Nb_0.02Zr_0.80Ti_0.20)O₃ [PCNZT] thin films were deposited on the Pt(1 1 1)/Ti/SiO₂/Si(1 0 0) substrates by RF magnetron sputtering with and without a LaNiO₃ [LNO] buffer layer. Ca and Nb elements in PZT films enhance the ferroelectric property, LaNiO₃ buffer layer improves the crystal quality of the PCNZT thin films. PCNZT thin films possess better ferroelectric property than that of PZT films for Ca and Nb ion substitution, moreover, PCNZT thin films with a LNO buffer layer possess (1 0 0) orientation and good ferroelectric properties with high remnant polarization (P_r = 38.1 μC/cm²), and low coercive field (E_c = 65 kV/cm), which is also better than that of PCNZT thin films without a LNO buffer layer (P_r = 27.9 μC/cm², E_c = 74 kV/cm). The result shows that enhanced ferroelectric property of PZT films can be obtained by ion substitution and buffer layer.     

The enhanced conductivity and stability of AZO thin films with a TiO2 buffer layer

Aluminum doped zinc oxide (AZO) films were substitutes of the SnO₂:F films on soda lime glass substrate in the amorphous thin-film solar cells due to good properties and low cost. In order to improve properties of AZO films, the TiO₂ buffer layer had been introduced. AZO films with and without TiO₂ buffer layer were deposited on soda lime glass substrates by r.f. magnetron sputtering. Subsequently, one group samples were annealed in vacuum (0.1 Pa) at 500 °C for 120 s using the RTA system, and the influence of TiO₂ thickness on the properties of AZO films had been discussed. The XRD measurement results showed that all the films had a preferentially oriented (0 0 2) peak, and the intensity of (0 0 2) peak had been enhanced for the AZO films with TiO₂ buffer layer. The resistivity of TiO₂ (3.0 nm)/AZO double-layer film is 4.76×10⁻⁴ Ω cm with the maximum figure merit of 1.92×10⁻² Ω⁻¹, and the resistivity has a remarkable 28.7% decrease comparing with that of the single AZO film. The carrier scattering mechanism of TiO₂ (3.0 nm)/AZO double-layer film had been described by Hall measurement in different temperatures. The average transmittance of all the films exceeded 92% in the visible spectrum. Another group samples were heat treated in the quartz tube in air atmosphere, and the effect of TiO₂ thickness on thermal stability of AZO films had been discussed.     

A study of the properties and microstructure of Ni81Fe19 ultrathin films with MgO

The anisotropic magnetoresistance (AMR) of a Ta (5 nm)/MgO (3 nm)/Ni₈₁Fe₁₉ (10 nm)/MgO (2 nm)/Ta (3 nm) film with MgO-Nano Oxide Layer (NOL) increases dramatically from 1.05% to 3.24% compared with a Ta (5 nm)/Ni₈₁Fe₁₉ (10 nm)/Ta (3 nm) film without the MgO-NOL layer after annealing at 380 °C for 2 h. Although the MgO destroys the NiFe (1 1 1) texture, it enhances the specular electron scattering of the conduction electrons at the NOL interface and suppresses the interface reactions and diffusion at the Ta/NiFe and NiFe/Ta interfaces. The NiFe (1 1 1) texture was formed after the annealing, resulting in a higher AMR ratio. X-ray photoelectron spectroscope results show that Mg and Mg²⁺ were present in the MgO_x films.     

Effect of buffer layers on the property of Pb(Zr,Ti)O3-Pb(Mn,W,Sb,Nb)O3 thin films grown by pulsed laser deposition

New ferroelectric Pb(Zr,Ti)O₃-Pb(Mn,W,Sb,Nb)O₃ (PZT-PMWSN) thin film has been deposited on a Pt/Ti/SiO₂/Si substrate by pulsed laser deposition. Buffer layer was adopted between film and substrate to improve the ferroelectric properties of PZT-PMWSN films. Effect of a Pb(Zr_0.52Ti_0.48)O₃ (PZT) and (Pb_0.72La_0.28)Ti_0.93O₃ (PLT) buffer layers on the stabilization of perovskite phase and the suppression of pyrochlore phase has been examined. Role of buffer layers was investigated depending on different types of buffer layer and thickness. The PZT-PMWSN thin films with buffer layer have higher remnant polarization and switching polarization values by suppressing pyrochlore phase formation. The remnant polarization, saturation polarization, coercive field and relative dielectric constant of 10-nm-thick PLT buffered PZT-PMWSN thin film with no pyrochlore phase were observed to be about 18.523 μC/cm², 47.538 μC/cm², 63.901 kV/cm and 854, respectively.     

Adhesion and stress of magnesium oxide thin films: Effect of thickness, oxidation temperature and duration

Nanoscale magnesium oxide thin films have been deposited on glass substrate by thermal oxidation (in air) of vacuum evaporated magnesium films. X-ray diffraction (XRD) showed orientation along (2 0 0) and (2 2 0) directions. The mechanical properties of the MgO thin films were found to be the function of thickness (300, 450 and 600 nm), oxidation temperature (573, 623 and 673 K) and oxidation duration (90 and 180 min). As oxidation temperature and oxidation duration increases, adhesion and intrinsic stress were found to increase. Intrinsic stress decreased whereas adhesion increased due to increase in thin film thickness. The value of intrinsic stress was in range 28.902-73.212 (×10⁷ N/m²) and that of adhesion was 12.1-27.4 (×10⁴ N/m²) for the thin film of thickness 300 nm.     

Improved surface morphology of flow-modulated MOVPE grown AIN on sapphire using thin medium-temperature AIN buffer layer

High-temperature (HT) AIN films were grown on (0 0 0 1) sapphire by low-pressure flow-modulated (FM) metal organic vapor phase epitaxy (MOVPE) with and without inserting a thin medium-temperature (MT) AIN layer. To suppress parasitic reactions between the sources of trimethylaluminum (TMA) and ammonia (NH₃), TMA and NH₃ was introduced to the reactor of MOVPE by alternating supply way. Surface morphology and crystalline quality were characterized by a scanning electronic microscopy (SEM), atomic force microscopy (AFM) and X-ray rocking curve (XRC) measurements of (0 0 0 2) and (10-12) diffractions. The AFM and SEM measurements indicated that the thin MT-AIN layer had a strong influence on the surface morphology of the HT-AIN films. The surface morphology became quite smooth by inserting the thin MT-AIN layer and surface RMS roughness values were 0.84 nm and 13.4 nm for the HT-AIN films with and without inserting the thin MT-AIN buffer layer, respectively. By etching the samples in aqueous KOH solution, it was found that the polarity of AIN films was different, the HT-AIN film with the thin MT-AIN layer could not be etched, indicating that the film had an Al-polar surface; however, the film without the MT-AIN layer was etched, which was explained that that film had a N- or mixed-polar surface. The mechanism for the origin of the different polarity of HT-AIN with and without the thin MT-AIN layer was proposed and discussed in detail.     

Long-length IBAD-MgO buffer layers for high performance RE-123 coated conductors by a large ion beam source

In Fujikura, a large-scale ion-beam-assisted deposition (IBAD) system with a large ion source has been employed to fabricate biaxially textured MgO films. The large-scale IBAD system has multiple deposition lanes where substrate tapes move, and therefore we have to optimize experimental conditions at each lane. We selected an appropriate deposition area and, finally, we successfully fabricated a 1 km-length IBAD-MgO film at a production rate of 1 km/h. We also studied pulsed-laser-deposited (PLD) CeO₂ films directly on the IBAD-MgO films in spite of a large lattice mismatch between CeO₂ and MgO. From transmission electron microscope (TEM) observations at an interface between MgO and CeO₂ films, it is revealed that there is domain-matching-epitaxy relationship between MgO and CeO₂ films. We also fabricated thin (1.0 μm) and thick (3.7 μm) PLD – GdBa₂Cu₃O_7−x (GdBCO) film on the long-length CeO₂/MgO substrate (over 150 m). Critical currents (I_c) and current density (J_c) were over 300 A and 3 MA/cm² respectively for the thin GdBCO film and were about 645 A and 1.7 MA/cm² for the thick GdBCO film at 77 K in self-field.     

The ferroelectric and ferromagnetic characterization of CoFe2O4/Pb(Mg1/3Nb2/3)O3-PbTiO3 multilayered thin films

The multiferroic (PMN-PT/CFO)_n (n = 1,2) multilayered thin films have been prepared on SiO₂/Si(1 0 0) substrate with LNO as buffer layer via a rf magnetron sputtering method. The structure and surface morphology of multilayered thin films were determined by X-ray diffraction (XRD) and atom force microscopy (AFM), respectively. The smooth, dense and crack-free surface shows the excellent crystal quality with root-mean-square (RMS) roughness only 2.9 nm, and average grain size of CFO thin films on the surface is about 44 nm. The influence of the thin films thickness size, periodicity n and crystallite orientation on their properties including ferroelectric, ferromagnetic properties in the (PMN-PT/CFO)_n multilayered thin films were investigated. For multilayered thin films with n = 1 and n = 2, the remanent polarization Pr are 17.9 μC/cm² and 9.9 μC/cm²; the coercivity H_c are 1044 Oe and 660 Oe, respectively. In addition, the relative mechanism are also discussed.     

Structural and magnetoresistive properties of half metallic Co2Mn1−xSi thin films

Polycrystalline Co₂Mn_1−xSi (CMS) thin films with Mn-deficiency can grow on different types of substrates such as MgO (1 0 0) single crystal, α-sapphire (0 0 0 1) and Si coated with SiO₂ either by using V or Ta/Cu as the seed layer. The magnetic property, especially the coercivity of the CMS thin films strongly depends on the crystalline structure and microstructure of the CMS thin film, hence it is affected by the substrate and also the seed layer. Very soft CMS thin film with coercivity of about 20 Oe has been obtained when MgO (1 0 0) is used as the substrate. Magnetic tunnel junctions (with MR ratio of about 9%–18%) by utilizing the CMS as one of ferromagnetic electrodes have been successfully fabricated. The degradation of the magnetoresistive effect of the MTJ after magnetic annealing is attributed to the diffusion of the Mn-atoms into the tunnel barrier during the annealing process.     

Comparison of the effect of PLT and PZT buffer layers on PZT thin films for ferroelectric materials applications

In order to study the effect of different buffer layers on the Pb(Zr_0.52Ti_0.48)O₃ (PZT) thin films, 10-nm thick (Pb_0.72La_0.28)Ti_0.93O₃ (PLT) and Pb(Zr_0.52Ti_0.48)O₃ buffer layers have been deposited on the Pt(1 1 1)/Ti/SiO₂/Si substrates by pulsed laser deposition, respectively. The top buffer layers were also deposited on PZT thin films with the same thickness of the seed layers in order to enhance the fatigue characteristics of PZT thin films. We compared the results of dielectric constant, hysteresis loops and fatigue resistance characteristics. It was found that the dielectric properties of PZT thin films with PLT buffer layers were improved by comparing with PZT thin films with PZT buffer layers. The polarization characteristics of PZT thin films with PLT buffer layers were observed to be superior to those of PZT thin films using PZT buffer layers. The remanent polarization of PZT thin films showed 36.3 μC/cm² and 2.6 μC/cm² each in the case of use PLT and PZT buffer layers. For the switching polarization endurance analysis, PZT thin films with PLT buffer layers showed more excellent result than that of PZT thin films with PZT buffer layers.     

Investigation on upconversion photoluminescence of Bi3TiNbO9:Er:Yb thin films

Bi₃TiNbO₉:Er³⁺:Yb³⁺ (BTNEY) thin films were fabricated on fused silica by pulsed laser deposition. It was demonstrated that different laser fluence and substrate temperature during growth of BTNEY upconversion photoluminescence (UC-PL) samples control the film’s grain size and hence influences the UC-PL properties. The average grain size of BTNEY thin films deposited on fused silica substrates with laser fluence 4, 5, 6, and 7 J/cm² are 30.8, 35.9, 40.6, and 43.4 nm, respectively. The 525 nm emission intensities increase with the deposition laser fluence and the emission intensities of BTNEY thin film deposited under 700 and 600 °C are almost 24 and 4 times, respectively, as strong as those of samples under 500 °C. The grain size of BTNEY thin film increases with the increasing temperature. UC-PL of BTNEY films is enhanced by increasing grain size of the films.     

Luminescence of ZnWO4 and CdWO4 thin films prepared by spray pyrolysis

Thin films of ZnWO₄ and CdWO₄ were prepared by spray pyrolysis and the structural, optical, and luminescence properties were investigated. Both ZnWO₄ and CdWO₄ thin films showed a broad blue-green emission band. The broad band of ZnWO₄ films was centered at 495 nm (2.51 eV) consisted of three bands at 444 nm (2.80 eV), 495 nm (2.51 eV) and 540 nm (2.30 eV). The broad band of CdWO₄ films at 495 nm (2.51 eV) could be decomposed to three bands at 444 nm (2.80 eV), 495 nm (2.51 eV) and 545 nm (2.28 eV). These results are consistent with emission from the WO₆⁶⁻ molecular complex. The luminance and efficiency for ZnWO₄ film at 5 kV and 57 μA/cm² were 48 cd/m² and 0.22 lm/w, respectively, and for CdWO₄ film the values were 420 cd/m² and 1.9 lm/w.     

Substrate effect on electronic sputtering yield in polycrystalline fluoride (LiF, CaF2 and BaF2) thin films

Influence of substrate on electronic sputtering of fluoride (LiF, CaF₂ and BaF₂) thin films, 10 and 100 nm thin, under dense electronic excitation of 120 MeV Ag²⁵⁺ ions irradiation is investigated. The sputtering yield of the films deposited on insulating (glass) and semiconducting (Si) substrates are determined by elastic recoil detection analysis technique. Results revealed that sputtering yield is higher, up to 7.4 × 10⁶ atoms/ion for LiF film on glass substrate, than that is reported for bulk materials/crystals (∼10⁴ atoms/ion), while a lower value of the yield (2.3 × 10⁶ atoms/ion) is observed for film deposited on Si substrate. The increase in the yield for thin films as compared to bulk material is a combined effect of the insulator substrate used for deposition and reduced film dimension. The results are explained in the framework of thermal spike model along with substrate and size effects in thin films. It is also observed that the material with higher band gap showed higher sputtering yield.