Negative‐pressure‐induced collector for a self‐balance free‐flow electrophoresis device

Uneven flow in free‐flow electrophoresis (FFE) with a gravity‐induced fraction collector caused by air bubbles in outlets and/or imbalance of the surface tension of collecting tubes would result in a poor separation. To solve these issues, this work describes a novel collector for FFE. The collector is composed of a self‐balance unit, multisoft pipe flow controller, fraction collector, and vacuum pump. A negative pressure induced continuous air flow rapidly flowed through the self‐balance unit, taking the background electrolyte and samples into the fraction collector. The developed collector has the following advantages: (i) supplying a stable and harmonious hydrodynamic environment in the separation chamber for FFE separation, (ii) effectively preventing background electrolyte and sample flow‐back at the outlet of the chamber and improving the resolution, (iii) increasing the preparative scale of the separation, and (iv) simplifying the operation. In addition, the cost of the FFE device was reduced without using a multichannel peristaltic pump for sample collection. Finally, comparative FFE experiments on dyes, proteins, and cells were carried out. It is evident that the new developed collector could overcome the problems inherent in the previous gravity‐induced self‐balance collector.     

Preliminary laser sampling in the microspectral analysis of metals and alloys

A new form of collector for laser erosion products in the microspectral analysis of metals and alloys has been suggested and investigated. The collector is in the form of a thin graphite disc with an axial aperture for a laser beam to pass. This collector makes the best use of laser erosion products both in the stage of sampling and in that of excitation. To obtain low detection limits the collector is introduced into a d.c. are discharge using a carrier or into a hollow cathode discharge in the presence of a magnetic field.     

Electrochemical Detection of Protons Produced in an Electrode Reaction Using Interdigitated Microarray Electrodes

This work describes the use of interdigitated array electrodes (IDAE) for proton detection. Methanol electrooxidation in sulfuric acid solution was exemplified. Reduction currents originating in the reaction product generated by methanol electrooxidation on a Pt generator electrode were observed at the Pt collector electrode, the potential of which was fixed in the hydrogen evolution region. In order to reduce the background current of hydrogen evolution, an Hg‐plated Pt collector electrode was fabricated. Compared to the Pt collector electrode, the reduction current observed at the Hg collector electrode was extremely small. The product detected was found to be a proton from the current responses observed at Pt and Hg collector electrodes.     

Development of orientation during electrospinning of fibres of poly(ε-caprolactone)

We explore the influence of a rotating collector on the internal structure of poly(ε-caprolactone) fibres electrospun from a solution in dichloroethane. We find that above a threshold collector speed, the mean fibre diameter reduces as the speed increases and the fibres are further extended. Small-angle and wide-angle X-ray scattering techniques show a preferred orientation of the lamellar crystals normal to the fibre axis which increases with collector speed to a maximum and then reduces. We have separated out the processes of fibre alignment on the collector and the orientation of crystals within the fibres. There are several stages to this behaviour which correspond to the situations (a) where the collector speed is slower than the fibre spinning rate, (b) the fibre is mechanically extended by the rotating collector and (c) where the deformation leads to fibre fracture. The mechanical deformation leads to a development of preferred orientation with extension which is similar to the prediction of the pseudo-affine deformation model and suggests that the deformation takes place during the spinning process after the crystals have formed.     

Adsorption of N-tallow 1,3-propanediamine-dioleate collector on albite and quartz minerals, and selective flotation of albite from greek stefania feldspar ore

The adsorption behavior of tallow 1,3-propanediamine-dioleate (Duomeen TDO) collector on albite and quartz minerals is assessed through Hallimond flotation, zeta potential, and diffuse reflectance FTIR investigations, together with the species distribution of the collector. The collector performance on albite separation from a natural feldspar material is evaluated in bench scale flotation tests. The Hallimond flotation responses of the minerals as a function of pH and collector concentration indicate that albite can be selectively floated from quartz at pH 2 where the doubly positively charged collector species adsorb on albite but not on quartz. However, the zeta potential and infrared spectra reveal that the adsorption behavior of the collector is similar on both minerals. The discrepancy in the flotation and adsorption results is attributed to the coarse and fine particle size fractions, and the shorter and longer equilibration periods employed in these studies respectively. The comparable adsorption on fine particles of albite and quartz at pH 2 is explained by the interaction of ammonium ions on silanol groups by hydrogen bonding as well as electrostatic interactions. The changes in zeta potentials are in good agreement with the formation of ionic species and free molecular forms of the collector. The IR spectra show the coexistence of neutral oleic acid together with charged amine species at low pH values in accordance with the species distribution diagram. Selective flotation of albite is accomplished from a natural feldspar material with tallow diamine-dioleate collector at pH 2 using sulfuric acid, only when the feed is deslimed prior to the bench scale flotation tests. An albite recovery exceeding 85% is achieved from a feed material containing about 50% albite.     

Resolving the coupled effects of hydrodynamics and DLVO forces on colloid attachment in porous media

Transport of colloidal particles in porous media is governed by the rate at which the colloids strike and stick to collector surfaces. Classic filtration theory has considered the influence of system hydrodynamics on determining the rate at which colloids strike collector surfaces, but has neglected the influence of hydrodynamic forces in the calculation of the collision efficiency. Computational simulations based on the sphere-in-cell model were conducted that considered the influence of hydrodynamic and Derjaguin-Landau-Verwey-Overbeek (DLVO) forces on colloid attachment to collectors of various shape and size. Our analysis indicated that hydrodynamic and DLVO forces and collector shape and size significantly influenced the colloid collision efficiency. Colloid attachment was only possible on regions of the collector where the torque from hydrodynamic shear acting on colloids adjacent to collector surfaces was less than the adhesive (DLVO) torque that resists detachment. The fraction of the collector surface area on which attachment was possible increased with solution ionic strength, collector size, and decreasing flow velocity. Simulations demonstrated that quantitative evaluation of colloid transport through porous media will require nontraditional approaches that account for hydrodynamic and DLVO forces as well as collector shape and size.     

捕收剂ADTB对一水硬铝石和铝硅矿物的捕收性能

研究了自制新型螯合捕收剂ADTB对一水硬铝石、高岭石和伊利石的浮选行为。单矿物浮选试验表明,该捕收剂对一水硬铝石、铝硅矿物的捕收能力差别较大,能有效分离一水硬铝石与铝硅矿物。通过动电位测试实验研究了捕收剂对矿物的吸附机理。结果表明:捕收剂在一水硬铝石表面可能是通过-COOH、-NHOH与Al-O形成双环螯合物的化学吸附,而在高岭石、伊利石表面主要是物理吸附。通过与捕收剂油酸进行比较,证明ADTB是一种较好的铝土矿正浮选捕收药剂。     

Electrochemical deposition of Ni on F-doped SnO<Subscript>2</Subscript> substrate and its post-annealing for use as current collector of dye-sensitized solar cell

Current collector is an important part of nanostructured dye-sensitized solar cells (DSSCs), which reduces ohmic loss. In the present work, Ni current collector was electrochemically deposited on fluorine-doped tin oxide (FTO) for use as current collector of DSSC. The adhesion of Ni to FTO was improved by post-annealing in ambient atmosphere. A new method was proposed to prevent Ni coating from oxidation during annealing. According to this method, a carbon over-layer was applied on Ni coating, which protected Ni from oxidation. Visual inspection and X-ray diffraction (XRD) results showed the effectiveness of this method in protection of Ni coating from oxidation. Furthermore, the effect of current collector on photovoltaic performance of DSSCs was investigated using current density-voltage curve measurement and electrochemical impedance spectroscopy methods. It was observed that post-annealing in ambient atmosphere, under protection of carbon over-layer, improves both the adhesion of Ni current collector to FTO and the photovoltaic performance of DSSC. However, Ni oxidation during post-annealing of Ni current collector, without carbon over-layer, significantly decreased the photovoltaic parameters of DSSC. The above observations were explained by considering the series resistance of DSSC.     

涂碳铝箔对磷酸铁锂电池性能影响研究

本文研究了使用涂碳铝箔作为正极集流体磷酸铁锂电池的性能。研究对比了使用普通铝箔和涂层铝箔的10 Ah软包磷酸铁锂电池的主要性能。研究表明：使用涂层铝箔不但可以提高磷酸铁锂材料的粘结性,而且使用导电涂层可以有效降低正极材料和集流体的接触内阻,从而减小电池内阻,提高电池倍率性能。与使用普通铝箔作为集流体相比,通过使用涂碳铝箔可以使得电池的内阻降低65%左右,但是,磷酸铁锂正极材料的克容量却偏低约5~10 mAh·g^-1,首次效率也偏低4%左右;在快速放电15C倍率下,使用涂碳铝箔的电芯比使用普通铝箔容量提高约15%左右,10C放电倍率下,平台增加0.3~0.4 V;使用涂碳铝箔电芯的常温自放电率较高,但容量恢复率也较高;550周循环下,使用涂碳铝箔可以使得电池的循环性能提高约1%。而在电池低温性能方面,使用涂碳铝箔对低温性能并无改善。     

涂碳铝箔对磷酸铁锂电池性能影响研究

本文研究了使用涂碳铝箔作为正极集流体磷酸铁锂电池的性能。研究对比了使用普通铝箔和涂层铝箔的10 Ah软包磷酸铁锂电池的主要性能。研究表明:使用涂层铝箔不但可以提高磷酸铁锂材料的粘结性,而且使用导电涂层可以有效降低正极材料和集流体的接触内阻,从而减小电池内阻,提高电池倍率性能。与使用普通铝箔作为集流体相比,通过使用涂碳铝箔可以使得电池的内阻降低65%左右,但是,磷酸铁锂正极材料的克容量却偏低约5~10 mAh·g-1,首次效率也偏低4%左右;在快速放电15C倍率下,使用涂碳铝箔的电芯比使用普通铝箔容量提高约15%左右,10C放电倍率下,平台增加0.3~0.4 V;使用涂碳铝箔电芯的常温自放电率较高,但容量恢复率也较高;550周循环下,使用涂碳铝箔可以使得电池的循环性能提高约1%。而在电池低温性能方面,使用涂碳铝箔对低温性能并无改善。     

Particle deposition onto Janus and patchy spherical collectors

An Eulerian model (convection-diffusion-migration equation) is presented to study colloid deposition behavior on Janus and patchy spherical collectors using Happel cell geometry. The model aims to capture the effect of the collector surface charge heterogeneity on the particle deposition rate. Two separate cases of surface charge distribution are presented. In the first case, the surface heterogeneity is modeled as half the collector favoring deposition and the other half hindering it (Janus collectors). For the second case, the surface heterogeneity is modeled as alternate stripes of attractive and repulsive regions on the collector (patchy collectors). The model also considers fluid flow approaching the collector at different angles in addition to the standard gravity assisted and gravity hindered flow conditions to analyze the effect of the collector orientation on the deposition. It was observed that particles tend to deposit at the edges of the favorable stripes and the extent of this preferential accumulation varies along the tangential position of the collector due to the nonuniform nature of the collector. The predicted deposition behavior is compared to the patchwise heterogeneity model. The study brings to fore how recent developments in synthesis of chemically heterogeneous particles and beads can be used for improved particle capture in porous media and for designing filter beds with enhanced life.     

Removal of Co(II) from dilute aqueous solutions by adsorption on charcoal and subsequent macroflotation of the sorbent

As a part of a research program on the treatment of radioactive process waste waters, sorbent macroflotation was tested to remove Co(II) from dilute aqueous solutions. Activated charcoal was used as the sorbent, and gelatin, cetylpyridinium chloride, dodecylamine or N-dodecylpyridinium chloride (NDPC) as the collector. In addition to the effect of the collector type on the percent removal, the effects of the pH, the charcoal and collector doses, the metal ion concentration, the ionic strength and the use of combinations of NDPC with other reagents have been investigated. At the optimum conditions removals better then 97% could be achieved in the pH range of 7.5–10.0 with NDPC plus a low concentration of a low-molecular-weight polyacrylamide. The results obtained are discussed in terms of hydrolysis of the metal ion and the electric state of both the charcoal and collector.     

Effect of carbon foams as negative current collectors on partial-state-of-charge performance of lead acid batteries

Flooded lead acid batteries were assembled by using a pitch-based carbon foam and a punched lead sheet as the negative current collectors, respectively. Comparative galvanostatic charge–discharge experiments were performed on the batteries to evaluate the effect of the carbon foam as a negative current collector material on the performance of lead acid batteries under partial-state-of-charge operation. The results indicate that the carbon foam negative current collector can significantly improve the cyclability of lead acid batteries under partial-state-of-charge operation. This is mainly attributed to the high specific surface area and three-dimensional, interconnected carbon ligaments of the carbon foam negative current collector.     

Increase in flotation activity of salts of higher aliphatic amines, potassium chloride collectors

For increasing the flotation activity of potassium chloride collector, salts of higher aliphatic amines, effects of a temperature of collector solutions, mixtures of homologues of different chain length, a solubilization of organic oleophilic compounds in the colloidal solutions of amine salts were examined on their micellar structure and ion-molecular composition.     

Fraction collector for capillary zone electrophoresis

An instrument is described which is capable of collecting fractions from a capillary zone electrophoresis apparatus. The fraction collector is characterized in terms of discretely collecting the separated components of a multi-component sample. In addition, the fraction collector permits the study of the effect of capillary zone electrophoresis on the biological activity of alpha-chymotrypsin.     

Theory and practice of electrochemical titrations with dual microband electrodes

Dual parallel microband electrodes, operated as a generator–collector pair and made by a simple, inexpensive mass-production method, have been used to implement a ‘titration’ method. The solution contains the electro-inactive analyte and a reagent from which the titrant can be generated electrochemically. The galvanostatically generated titrant is detected at the collector amperometrically. The collection efficiency is affected by the reaction between the titrant and the analyte. Determination of ascorbic acid by titration against ferricyanide is given as an example. The measurement is performed as follows: After application of the collector potential, the boundary conditions between measurements are renewed by a quick pulsed motion of the electrode assembly. Then the generator current is applied. Following an initial delay, the collector current increases as t^1/2, with slope and collection efficiency dependent on analyte concentration. This results in a fast and effective method for implementing some standard titration methods without the need for accurate volume measurement and reagent preparation. The accuracy is determined by the reproducibility of electrodes. The present work shows concentration measurements in the mM scale to ≈±10%, in a time of a few seconds. The highly stable extrapolation method used for numerical simulation of the generator–collector experiment, which takes into account the non-uniform current distribution over a microband electrode with a galvanostatic boundary condition, is developed using a conformal map. A good agreement between simulations and experimental results was obtained in voltammetric, potential step and generator–collector measurements. It is shown that a useful approximate calculation can be made rather easily by representing the problem in terms of a reaction layer in the conformal space.     

Selective separation of pyrite and chalcopyrite by biomodulation

Selective separation of pyrite from other associated ferrous sulphides at acidic and neutral pH has been a challenging problem. This paper discusses the utility of Acidithiobacillus ferrooxidans for the selective flotation of chalcopyrite from pyrite. Consequent to interaction with bacterial cells, pyrite remained depressed even in the presence of potassium isopropyl xanthate collector while chalcopyrite exhibited significant flotability. However, when the minerals were conditioned together, the selectivity achieved was poor due to the activation of pyrite surface by the copper ions in solution. The selectivity was improved when the sequence of conditioning with bacterial cells and collector was reversed, since the bacterial cells were able to depress collector interacted pyrite effectively, while having negligible effect on chalcopyrite. The observed behaviour is analysed and discussed in detail. The separation obtained was significant both at acidic and alkaline pH. This selectivity achieved was retained when the minerals were interacted with both bacterial cells and collector simultaneously.     

Effect of particle size distribution on the collection efficiency of Brownian particles

The main purpose of the present paper is to investigate the effect of the normal Gaussian size distribution on the deposition of Brownian particles onto a spherical collector, by applying the Brownian dynamic simulation method and the Kuwabara flow field model with different types of DLVO interaction energy curves and the shadow effect. The simulation results show that the collection efficiency of Brownian particles always increases with a wider particle size distribution region. The same increased tendencies are also observed for the case of increasing Reynolds number and for the case of increasing the particle size to the collector size ratio. When compared to the available experimental data, the present simulation method fits well with the experimental data when the specific deposit per collector is not large.     

A new variable dispersion double-focusing plasma mass spectrometer with performance illustrated for Pb isotopes

A new generation multiple collector plasma source mass spectrometer (PSMS) produced by Nu Instruments Ltd is evaluated. The instrument has a double-focusing Nier–Johnson analyser with laminated magnet and a novel variable dispersion ion optical arrangement, enabling all masses to be located in the centre of the Faraday collectors of a fixed static array. mThe performance of the instrument has been assessed through the analysis of NBS-981 Pb using a Tl doping technique with Faraday collector efficiencies and amplifier gains determined independently. A second method of analysis involves comparison of interspersed standard and sample Pb measurements with effective gains for each collector determined from the standards. In both cases the repetition of Pb isotope measurement is competetive with the thermal ionization mass spectrometry (TIMS) double-spike method.     

Reduced graphene oxide as a protective layer of the current collector of a lithium-ion battery

The possibility of protecting the current collector of the cathode of a lithium-ion battery from the corrosive agents of electrolyte by creating a protective shell of reduced graphene oxide on the collector surface was studied. The positive effect was found to be a decrease in the degree of Faraday processes. The results of scanning electron microscopy, XRD analysis, Raman spectroscopy, and cyclic voltammetry were presented.