Monte Carlo simulation of density dependence of molecular motion and radical decay in solid polymers

It was found experimentally that after increasing pressure, the decay of free-radicals in solid polymers is slowed down (Szöcs F, Rostašová O, Tiňo J, Plac̆ek J, European Polym J, 1974;10:725). Since the mechanism for decay is associated with molecular mobility, a Monte Carlo method has been used for studying the effect of the polymer density on molecular mobility and free-radical decay in a model system with the parameters close to those of polyethylene. Increased pressure is correlated with higher density of the polymer system. Rotational motions were found to be considerably limited at increased density (ρ=0.85 g cm⁻³ versus 0.81 g cm⁻³). Consequently, free-radical decay is slowed down at the higher density in accord with the experimental results.     

Electronic structure and Raman spectroscopy study of dibarium magnesium orthoborate,Ba2Mg(BO3)2

The samples of dibarium magnesium orthoborate Ba₂Mg(BO₃)₂ were synthesized by solid-state reaction. The X-ray diffraction (XRD) patterns and Raman spectra of the samples were collected. Electronic structure and vibrational spectroscopy of Ba₂Mg(BO₃)₂ were systematically investigated by first principle calculation. A direct band gap of 4.4 eV was obtained from the calculated electronic structure results. The top valence band is constructed from O 2p states and the low conduction band mainly consists of Ba 5d states. Raman spectra for Ba₂Mg(BO₃)₂ polycrystalline were obtained at ambient temperature. The factor group analysis results show the total lattice modes are 5E_u + 4A_2u + 5E_g + 4A_1g + 1A_2g + 1A_1u, of which 5E_g + 4A_1g are Raman-active. Furthermore, we obtained the Raman active vibrational modes as well as their eigenfrequencies using first-principle calculation. With the assistance of the first-principle calculation and factor group analysis results, Raman bands of Ba₂Mg(BO₃)₂ were assigned as E_g (42 cm⁻¹), A_1g (85 cm⁻¹), E_g (156 cm⁻¹), E_g (237 cm⁻¹), A_1g (286 cm⁻¹), E_g (564 cm⁻¹), A_1g (761 cm⁻¹), A_1g (909 cm⁻¹), E_g (1165 cm⁻¹). The strongest band at 928 cm⁻¹ in the experimental spectrum is assigned to totally symmetric stretching mode of the BO₃ units.     

In-plane chemical pressure in (U1−yCey)O2 studied by Raman spectroscopy

We investigate the nature of bonding and charge states in (U_1−yCe_y)O₂ (y = 0.0, 0.2, 0.4, 0.6, 0.8 and 1.0) by Raman spectroscopy. Raman spectrum of UO₂ exhibits two prominent bands below 1000 cm⁻¹, a F_2g mode at 446 cm⁻¹ and a F_1u LO mode at 578 cm⁻¹. As y is increased from 0 to 0.6, the F_1u exhibits a large blue shift of 90 cm⁻¹, and from y = 0.6 to 1.0, a red shift of 54 cm⁻¹. We show that our results can be interpreted as arising from anisotropic compression/relaxation of the lattice under Ce substitution and this can give an indication of its charge states. Alternate interpretations have been given in the literature on the effect of substituents and dopants to the Raman spectra of UO₂ and CeO₂. The present interpretation of chemical stress effects can be taken as another plausible explanation.     

Investigation of anharmonicity in rotational phonon mode for BaWO4 crystal

Spontaneous Raman spectra in the BaWO₄ were measured in the temperature range from 4 K to 280 K, and the temperature dependence of the linewidth of the A_g (191 cm⁻¹) Raman mode was analyzed using the lattice dynamical perturbative approach and one-phonon density of states (PDOS). The linewidth slope for the 191 cm⁻¹ peak for an external mode is 7.2 times larger than that for the 926 cm⁻¹ peak for a breathing mode. The different behaviors of these two modes in the case of temperature broadening could be attributed to the large energy band gap in the one-phonon density of states (PDOS) resulting in different anharmonic interactions. The origin may be that the ratio of up-conversion TDOS to down-conversion TDOS for Eg mode (191 cm⁻¹) is more than that for A_g (926 cm⁻¹). The peak of the Eg mode (191 cm⁻¹) is attributed to the coupling mode both a rotation of the Barium and an out-of-phase rotation of the oxygen in x–y plane as a librational mode.     

Vibrational and electronic properties of single-walled and double-walled boron nitride nanotubes

We calculated IR, nonresonance Raman spectra and vertical electronic transitions of the zigzag single-walled and double-walled boron nitride nanotubes ((0,n)-SWBNNTs and (0,n)@(0,2n)-DWBNNTs). In the low frequency range below 600 cm⁻¹, the calculated Raman spectra of the nanotubes showed that RBMs (radial breathing modes) are strongly diameter-dependent, and in addition the RBMs of the DWBNNTs are blue-shifted reference to their corresponding one in the Raman spectra of the isolated (0,n)-SWBNNTs. In the high frequency range above ∼1200 cm⁻¹, two proximate Raman features with symmetries of the A_1g (∼1355 ± 10 cm⁻¹) and E_2g (∼1330 ± 25 cm⁻¹) first increase in frequency then approach a constant value of ∼1365 and ∼1356 cm⁻¹, respectively, with increasing tubes’ diameter, which is in excellent agreement with experimental observations. The calculated IR spectra exhibited IR features in the range of 1200–1550 cm⁻¹ and in mid-frequency region are consistent with experiments. The calculated dipole allowed singlet–singlet and triplet–triplet electronic transitions suggesting a charge transfer process between the outer- and inner-shells of the DWBNNTs as well as, upon irradiation, the possibility of a system that can undergo internal conversion (IC) and intersystem crossing (ISC) processes, besides the photochemical and other photophysical processes.     

Excess molar enthalpies and excess molar volumes of (1,3-dimethyl-2-imidazolidinone + an aromatic hydrocarbon) atT = 298.15 K

Excess molar enthalpies H_m^Eand excess molar volumesV_m^E of (1,3-dimethyl-2-imidazolidinone  +  benzene, or methylbenzene, or 1,2-dimethylbenzene, or 1,3-dimethylbenzene, or 1,4-dimethylbenzene, or 1,3,5-trimethylbenzene, or ethylbenzene) over the whole range of compositions have been measured at T =  298.15 K. The excess molar enthalpy values were positive for five of the seven systems studied and the excess molar volume values were negative for six of the seven systems studied. The excess enthalpy ranged from a maximum of 435 J · mol ^− 1for (1,3-dimethyl-2-imidazoline  +  1,3,5-trimethylbenzene) to a minimum of  − 308 J · mol ^− 1for (1,3-dimethyl-2-imidazoline  +  benzene). The excess molar volume values ranged from a maximum of 0.95cm³mol ^− 1 for (1,3-dimethyl-2-imidazoline  +  ethylbenzene) and a minimum of  − 1.41 cm³mol ^− 1for (1,3-dimethyl-2-imidazoline  +  methylbenzene). The Redlich–Kister polynomial was used to correlate both the excess molar enthalpy and the excess molar volume data and the NRTL and UNIQUAC models were used to correlate the enthalpy of mixing data. The NRTL equation was found to be more suitable than the UNIQUAC equation for these systems. The results are discussed in terms of the polarizability of the aromatic compound and the effect of methyl substituents on the benzene ring.     

Preparation of monodisperse carbon nanospheres for electrochemical capacitors

The efficiently hydrothermal route using sucrose without any catalysts is employed to prepare the uniform carbon spheres. The monodisperse 100–150 nm carbon spheres are obtained with the activation treatment in molten KOH. The carbon spheres are characterized by transmission electron microscope, X-ray diffraction, N₂ adsorption, Raman spectroscopy and electrochemical techniques. The relationships of specific capacitance and surface properties of carbon spheres are investigated. A single electrode of carbon nanosphere materials performs excellent specific capacitance (328 F g⁻¹), area capacitance (19.2 μF cm⁻²) and volumetric capacitance (383 F cm⁻³).     

Diffusion of ferrocene methanol in super-cooled aqueous solutions using cylindrical microelectrodes

The diffusion of ferrocene methanol in super-cooled aqueous solutions containing sucrose has been studied, using disk and cylindrical microelectrodes, over a wide viscosity range. The solution viscosity and the reduced temperature T/T_g (T_g being the glass transition temperature) were varied by changing the sucrose concentration and the temperature of the system. The voltammetric limiting current obtained with a disk microelectrode and the i(t) response on a cylindrical microelectrode after a potential step were used to determine diffusion coefficients from 7 × 10⁻⁶ cm² s⁻¹ down to 2 × 10⁻¹¹ cm² s⁻¹. The electrochemical procedure described in this work allows a simple and accurate measurement of the dynamics of electroactive solutes in glass-forming liquids.     

Investigation of the phonon band gap effect on Raman-active optical phonons in SrMoO4 crystal

The phonon dispersions of SrMoO₄ crystal are calculated using the lattice dynamical calculations approach. Spontaneous Raman spectra in the SrMoO₄ were measured in the temperature range from 10 K to 295 K, and the temperature dependence of the linewidth of the B_g (95 cm⁻¹) and A_g (888 cm⁻¹) Raman modes was analyzed using the lattice dynamical perturbative approach. We found that different behaviors of these two modes in the case of temperature broadening could be attributed to the large energy band gap in the phonon spectrum resulting in different anharmonic interactions. The calculated temperature dependence of the linewidth of A_g (888 cm⁻¹) mode was well accounted for the experimental one by including both down-conversion by the cubic term and the dephasing by quartic term. The dephasing processes are increased only at high temperatures and the effect of dephasing is related to the size of a large phonon band gap.     

The state energy and the displacements of the potential minima of the 2Ag− state in all-trans-β-carotene as determined by fluorescence spectroscopy

The fluorescence spectrum of all-trans-β-carotene was recorded at 170 K. The 1B_u⁺ → 1A_g⁻ fluorescence exhibited clear vibrational structures constituting a mirror image with those of the 1B_u⁺ ← 1A_g⁻ absorption, and the deconvolution of the entire spectrum identified the 2A_g⁻(0) → 1A_g⁻(0) transition at 14 500 cm⁻¹. The displacements of the 1B_u⁺ and 2A_g⁻ potential minima along ν₁ and ν₂ (the CC stretching and C–C stretching normal coordinates, respectively) were determined to be 1.2 and 0.9, and 1.6 and 1.5, respectively. Thus, much larger potential displacements in the 2A_g⁻ state than in the 1Bu⁺ state have been shown.     

Excess molar volumes of binary mixtures of 2,2,2-trifluoroethanol with water,or acetone,or 1,4-difluorobenzene,or 4-fluorotoluene,or α,α,α, trifluorotoluene or 1-alcohols at a temperature of 298.15 K and pressure of 101 kPa

Excess molar volumes V_m^E of binary mixtures of 2,2,2-trifluoroethanol with water, or acetone, or methanol, or ethanol, or 1-alcholos, or 1,4-difluorobenzene, or 4-fluorotoluene or α,α,α-trifluorotoluene were measured in a vibrating tube densimeter at temperature 298.15 K and pressure of 101 kPa. The V_m^E extrema are: 1.540 cm³ · mol⁻¹ for (2,2,2-trifluoroethanol + 1-heptanol); 1.452 cm³ · mol⁻¹ for (2,2,2-trifluoroethanol + 1-hexanol); 1.238 cm³ · mol⁻¹ for (2,2,2-trifluoroethanol + 1-butanol); 0.821 cm³ · mol⁻¹ for (2,2,2-trifluoroethanol + 4-fluorotoluene); 0.817 cm³ · mol⁻¹ for (2,2,2-trifluoroethanol + ethanol); 0.647 cm³ · mol⁻¹ for (2,2,2-trifluoroethanol + methanol); 0.618 cm³ · mol⁻¹ for (2,2,2-trifluoroethanol + acetone); 0.605 cm³ · mol⁻¹ for (2,2,2-trifluoroethanol + α,α,α-trifluorotoluene); 0.485 cm³ · mol⁻¹ for (2,2,2-trifluoroethanol + 1,4-difluorobenzene); and −0.656 cm³ · mol⁻¹ for (2,2,2-trifluoroethanol + water). The limiting excess partial molar volumes are estimated.     

Effective bioelectrocatalysis of bilirubin oxidase on electrochemically reduced graphene oxide

Graphene oxide (GO) was applied for construction of an effective biocathode based on bilirubin oxidase (BOD). Separation of small-sized GO sheets together with the BOD immobilisation protocol has detrimental effects on the bioelectrocatalytic reduction of oxygen. When BOD was deposited on electrochemically reduced GO (ErGO) only a negligible current density j = 2.6 μA cm^− 2 was observed. Current density dramatically increased to a value of 46 μA cm^− 2 once BOD was in-situ mixed with as-received GO directly on a glassy carbon electrode (GCE) with subsequent electrochemical reduction of the BOD/GO composite. When this protocol was tested with small-sized GO flakes separated simply using centrifugation, the fabricated biocathode exhibited j = 120 μA cm^− 2. A current density further increased to j = 280 μA cm^− 2 when BOD and purified GO were incubated ex-situ for 4 h, followed by the BOD/GO composite collection by centrifugation, its deposition on the GCE and electrochemical reduction. Moreover, oxygen reduction current increased steeply with a steady-state current density achieved at high potential (≈ 500 mV), close to the onset potential of oxygen reduction (≈ 580 mV).     

Development of micro-tubular SOFCs with an improved performance via nano-Ag impregnation for intermediate temperature operation

Micro-tubular solid-oxide fuel cell consisting of a 10-μm thick (ZrO₂)_0.89(Sc₂O₃)_0.1(CeO₂)_0.01 (ScSZ) electrolyte on a support NiO/(ScSZ) anode (1.8 mm diameter, 200 μm wall thickness) with a Ce_0.8Gd_0.2O_1.9 (GDC) buffer-layer and a La_0.6Sr_0.4Co_0.2Fe_0.8O_3−δ (LSCF)/GDC functional cathode has been developed for intermediate temperature operation. The functional cathode was in situ formed by impregnating the well-dispersed nano-Ag particles into the porous LSCF/GDC layer using a citrate method. The cells yielded maximum power densities of 1.06 W cm⁻² (1.43 A cm⁻², 0.74 V), 0.98 W cm⁻² (1.78 A cm⁻², 0.55 V) and 0.49 W cm⁻² (1.44 A cm⁻², 0.34 V), at 650, 600 and 550 °C, respectively.     

Vibrational spectroscopic study of syngenite formed during the treatment of liquid manure with sulphuric acid

Syngenite (K₂Ca(SO₄)₂·H₂O), formed during treatment of manure with sulphuric acid, was studied by infrared, near-infrared (NIR) and Raman spectroscopy. C_s site symmetry was determined for the two sulphate groups in syngenite (P2₁/m), so all bands are both infrared and Raman active. The split ν₁ (two Raman+two infrared bands) was observed at 981 and 1000 cm⁻¹. The split ν₂ (four Raman+four infrared bands) was observed in the Raman spectrum at 424, 441, 471 and 491 cm⁻¹. In the infrared spectrum, only one band was observed at 439 cm⁻¹. From the split ν₃ (six Raman+six infrared) bands three 298 K Raman bands were observed at 1117, 1138 and 1166 cm⁻¹. Cooling to 77 K resulted in four bands at 1119, 1136, 1144 and 1167 cm⁻¹. In the infrared spectrum, five bands were observed at 1110, 1125, 1136, 1148 and 1193 cm⁻¹. From the split ν₄ (six infrared+six Raman bands) four bands were observed in the infrared spectrum at 604, 617, 644 and 657 cm⁻¹. The 298 K Raman spectrum showed one band at 641 cm⁻¹, while at 77 K four bands were observed at 607, 621, 634 and 643 cm⁻¹. Crystal water is observed in the infrared spectrum by the OH-liberation mode at 754 cm⁻¹, OH-bending mode at 1631 cm⁻¹, OH-stretching modes at 3248 (symmetric) and 3377 cm⁻¹ (antisymmetric) and a combination band at 3510 cm⁻¹ of the H-bonded OH-mode plus the OH-stretching mode. The near-infrared spectrum gave information about the crystal water resulting in overtone and combination bands of OH-liberation, OH-bending and OH-stretching modes.     

Achieving high electrode specific capacitance with materials of low mass specific capacitance: Potentiostatically grown thick micro-nanoporous PEDOT films

Electrode materials for supercapacitors are at present commonly evaluated and selected by their mass specific capacitance (C_M, F g⁻¹). However, using only this parameter may be a misleading practice because the electrode capacitance also depends on kinetics, and may not increase simply by increasing material mass. It is therefore important to complement C_M by the practically accessible electrode specific capacitance (C_E, F cm⁻²) in material selection. Poly[3,4-ethylene-dioxythiophene] (PEDOT) has a mass specific capacitance lower than other common conducting polymers, e.g. polyaniline. However, as demonstrated in this communication, this polymer can be potentiostatically grown to very thick films (up to 0.5 mm) that were porous at both micro- and nanometer scales. Measured by both cyclic voltammetry and electrochemical impedance spectrometry, these thick PEDOT films exhibited electrode specific capacitance (C_E, F cm⁻²) increasing linearly with the film deposition charge, approaching 5 F cm⁻², which is currently the highest amongst all reported materials.     

VO2 nano-sheet negative electrodes for lithium-ion batteries

Vanadium dioxide (VO₂) nano-sheets were directly synthesized via a continuous hydrothermal process and were investigated as electrodes in a wide potential range of 0.05–3 V vs. Li/Li⁺. The nano-sheets showed excellent capacity retention, with a specific capacity of 350 mAh g^− 1 at an applied current of 0.1 A g^− 1 and 95 mAh g^− 1 at 10 A g^− 1. Further electrochemical testing suggested that a significant proportion of the charge storage in the cells was due to pseudocapacitive processes.     

Construction,calibration and testing of a micro-combustion calorimeter

An isoperibolic micro-combustion calorimeter was designed, built and set up in our laboratory, taking as base a 1107 Parr combustion bomb of 22 cm³ of volume. Taken into account the geometrical form of the bomb, it was designed and constructed a vessel and a submarine chamber in brass. All of the pieces of the calorimeter were chromium-plated to reduce heat loss by radiation. The calorimeter was calibrated by using pellets of standard benzoic acid (mass approximate of 40 mg) leading to the energy equivalent of ε(calor) = (1283.8 ± 0.6) J · K⁻¹. In order to test the calorimeter, combustion experiments of salicylic acid were performed leading to a value of combustion energy of Δ_cu^∘ = −(21,888.8 ± 10.9) J · g⁻¹, which agrees with the reported literature values. The combustion of piperonylic acid was carried out as a further test leading to a value of combustion energy of Δ_cu^∘ = −(20,215.9 ± 10.4) J · g⁻¹ in accordance with the reported literature value. The uncertainty of the calibration and the combustion of salicylic acid and piperonylic acid was 0.05%.     

Outstanding room-temperature capacitance of biomass-derived microporous carbons in ionic liquid electrolyte

A remarkable capacitance of 180 F·g^− 1 (at 5 mV·s^− 1) in solvent-free room-temperature ionic liquid electrolyte, 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide, was achieved in symmetric supercapacitors using microporous carbons with a specific surface area of ca. 2000 m²·g^− 1 calculated from gas sorption by the 2D-NLDFT method. The efficient capacitive charge storage was ascribed to textural properties: unlike most activated carbons, high specific surface area was made accessible to the bulky ions of the ionic liquid electrolyte thanks to micropores (1–2 nm) enabled by fine-tuning chemical activation. From the industrial perspective, a high volumetric capacitance of ca. 80 F·cm^− 3 was reached in neat ionic liquid due to the absence of mesopores. The use of microporous carbons from biomass waste represents an important advantage for large-scale production of high energy density supercapacitors.     

Standard molar volumes and expansibilities of 1,3-alkyl-N-substituted achiral glycolurils in water at T = (278.15 to 318.15) K and p = 0.1 MPa: A comparative analysis

Densities of aqueous solutions of achiral 1,3-dimethylglycoluril (1,3-DMGU) and 1,3-diethylglycoluril (1,3-DEGU) were measured using a hermetically sealed vibrating-tube densimeter, with an uncertainty of 1 · 10⁻⁵ g · cm⁻³, at T = (278.15, 288.15, 298.15, 308.15, and 318.15) K and p = (99.6 ± 0.8) kPa. The solute molality was ranged from (0.06 to 0.39) and from (0.01 to 0.07) mol · kg⁻¹ for the aqueous 1,3-DMGU and 1,3-DEGU, respectively. The standard (at infinite dilution) molar volumes and isobaric expansibilities for the 1,3-dialkyl-N-substituted glycolurils compared in water were calculated and discussed in comparison with the previously derived molar enthalpies and heat capacities of their dissolution (hydration). The temperature-dependent behavior of packing-related hydration effects was described taking into account the structural features of a solute molecule.     

Densities of {poly(ethylene glycol) + water} over the temperature range (283.15 to 363.15) K

Densities of {poly(ethylene glycol) [PEG] + water} prepared with PEG average molar mass (200, 400, 600, and 1500) g · mol^?1 have been measured over the entire composition range over the temperature range (283.15 to 363.15) K at 10 K intervals using a density meter based on electromagnetically-induced oscillations of a U-shaped glass tube and an inbuilt Peltier thermostat. The density versus temperature data of (PEG + water) at each composition for all PEGs were fit to a simple quadratic equation: ρ/(g · cm^?3) = ρ₀/(g · cm^?3) + a(T/K) + b(T/K)². Fits were observed to be satisfactory at each composition for all four (PEG + water). The excess molar volumes of (PEG + water) are observed to be negative and significant over the entire composition range for all four (PEG + water). Irrespective of the temperature, the maximum absolute excess molar volumes are observed in the water-rich region of the mixture and are found to decrease with increasing temperature. This is attributed to the presence of strong interactions within the (PEG + water). Specifically, it is proposed to be due to the H-bonding interactions between the PEG and the water molecules within the mixtures.