Investigation of interferences in the determination of thallium in marine sediment reference materials using high-resolution continuum-source atomic absorption spectrometry and electrothermal atomization

A high-resolution continuum-source atomic absorption spectrometer with a xenon short-arc lamp as the radiation source, a compact double echelle monochromator with a focal length of 302 mm and a spectral resolution of λ/Δλ≈110 000, and a UV-sensitive charged-coupled device (CCD) array detector was used to investigate the spectral interferences found with a conventional line-source atomic absorption spectrometer in the determination of thallium in marine sediment reference materials. A transversely heated graphite furnace was used as the atomizer unit, and the samples were introduced in the form of slurries. A strong iron absorption line at 276.752 nm, which was observed at atomization temperatures >2000 °C in the vicinity of the thallium resonance line at 276.787 nm, could be responsible for some of the interferences observed with low-resolution continuum-source background correction. The outstanding feature at atomization temperatures <2000 °C was the electron excitation spectrum of the gaseous SO₂ molecule that exhibited a pronounced rotational fine structure, and is for sure the main reason for the observed spectral interferences. The molecular structures could be removed completely by subtracting a model spectrum recorded during the atomization of KHSO₄, using a least squares algorithm. The same results, within experimental error, were obtained for thallium in a variety of marine sediment reference materials using ammonium nitrate as a modifier, ruthenium as a permanent modifier in addition to ammonium nitrate, and without a modifier, using aqueous standards for calibration, demonstrating the ruggedness of the method. A characteristic mass of 15–16 pg Tl was obtained, and a limit of detection of 0.02 μg g⁻¹ Tl was calculated from the standard deviation of five repetitive determinations of HISS-1, the sediment with the lowest thallium content.     

Feasibility of eliminating interferences in graphite furnace atomic absorption spectrometry using analyte transfer to the permanently modified graphite tube surface

A procedure is proposed to avoid spectral and/or non-spectral interferences in graphite furnace atomic absorption spectrometry (GF AAS) by transferring the analyte during the pyrolysis stage from a solid sampling platform to the graphite tube wall that has been coated with a permanent modifier, e.g. by electrodeposition of a platinum-group metal. The direct determination of mercury in solid coal samples was chosen as a model to investigate the feasibility of this idea. The graphite tube surface was coated with palladium and the analyte was transferred from the solid sampling platform to the tube wall at a temperature of 500±50 °C. A characteristic mass of m₀=64 pg Hg was obtained for an atomization temperature of 1300 °C, proposing a quantitative transfer of the analyte to the tube wall. Calibration against aqueous mercury standards was not feasible as this element was lost in part already during the drying stage and could not be trapped quantitatively on the modified graphite tube surface. However, the results for all except one of the coal reference materials were within the 95% confidence interval of the certificate when the slope of a correlation curve between the integrated absorbance, normalized for 1 mg of sample, and the certified value for mercury was used for calibration. A detection limit of 0.025–0.05 μg g⁻¹ Hg in coal, calculated from three times the standard deviation of the investigated coal samples, could be obtained with the proposed method. The spectral interference due to excessive background absorption in the direct determination of mercury in coal could be eliminated completely. It is expected that this analyte transfer can be used in a similar way to eliminate other spectral and/or non-spectral interferences in the GF AAS determination of other volatile analytes.     

Trace Determination of Manganese in Urine by Graphite Furnace Atomic Absorption Spectrometry and Inductively Coupled Plasma–Mass Spectrometry

This paper describes a simple and sensitive method for the determination of manganese in human urine by graphite furnace atomic absorption spectroscopy (GFAAS), which includes sample preparation by microwave digestion. Matrix modifier combinations, the digestion power, pyrolysis, and atomization temperatures were optimized. A mixture of 5.0 µg Pd(NO₃)₂ and 3.2 µg Mg(NO₃)₂ modifier presented the best performance. The optimal temperatures for pyrolysis and atomization were 1500°C and 1950°C, respectively. The GFAAS method was compared to inductively coupled plasma–mass spectrometry (ICP–MS) for the determination of manganese in urine. Analytical figures of merit for GFAAS and ICP–MS were: accuracy (3.46%, 2.19%), precision (3.61%, 5.84%), LOD (0.109 µg · L^?1, 0.015 µg · L^?1), LOQ (0.327 µg · L^?1, 0.045 µg · L^?1), and recovery (80–100%, 74–89%). Both methods were employed for the determination of Mn in urine and the results were compared statistically.     

Spectral and non-spectral interferences in the determination of thallium in environmental materials using electrothermal atomization and vaporization techniques—a case study

The literature on the determination of Tl in environmental samples using electrothermal atomization (ETA) and vaporization (ETV) techniques has been reviewed with special attention devoted to potential interferences and their control. Chloride interference, which is due to the formation of the volatile monochloride in the condensed phase, is the most frequently observed problem. Due to its high dissociation energy (88 kcal/mol), TlCl is difficult to dissociate in the gas phase and is easily lost. The best means of controlling this interference in ETA is atomization under isothermal conditions according to the stabilized temperature platform furnace concept, and the use of reduced palladium as a modifier. An alternative approach appears to be the ‘fast furnace’ concept, wherein both the use of a modifier and the pyrolysis stage are omitted. This concept requires an efficient background correction system, and high-resolution continuum-source atomic absorption spectrometry (HR-CS AAS) appears to offer the best results. This chloride interference can also cause significant problems when ETV techniques are used. Among the spectral interferences found in the determination of thallium are those due to Pd, the most efficient modifier, and Fe, which is frequently found at high concentrations in environmental samples. Both interferences are due to nearby atomic lines, and are observed only when deuterium background correction and relatively high atomization temperatures are used. A more serious spectral interference is that due to the molecular absorption spectrum of SO₂, which has a maximum around the Tl line and exhibits a pronounced rotational fine structure. HR-CS AAS again showed the best performance in coping with this interference.     

Investigation of interference mechanism of cobalt chloride on the determination of bismuth by electrothermal atomic absorption spectrometry

The interferences of cobalt chloride on the determination of bismuth by electrothermal atomic absorption spectrometry (ETAAS) were examined using a dual cavity platform (DCP), which allows the gas-phase and condensed phase interferences to be distinguished. Effects of pyrolysis temperature, pyrolysis time, atomization temperature, heating rate in the atomization step, gas-flow rate in the pyrolysis and atomization steps, interferent mass and atomization from wall on sensitivity as well as atomization signals were studied to explain the interference mechanisms. The mechanism proposed for each experiment was verified with other subsequent sets of experiments. Finally, modifiers pipetted on the thermally treated sample+interferent mixture and pyrolyzed at different temperatures provided very useful information for the existence of volatilization losses of analyte before the atomization step. All experiments confirmed that when low pyrolysis temperatures are applied, the main interference mechanisms are the gas-phase reaction between bismuth and decomposition products of cobalt chloride in the atomization step. On the other hand, at elevated temperatures, the removal of a volatile compound formed between analyte and matrix constituents is responsible for some temperature-dependent interferences, although gas-phase interferences still continue. The experiments performed with colloidal palladium and nickel nitrate showed that the modifier behaves as both a matrix modifier and analyte modifier, possibly delaying the vaporization of either analyte or modifier or both of them.     

Spectrophotometric determination of etodolac in pure form and pharmaceutical formulations

Background

A routine method for the quantification of beryllium in biological fluids is essential for the development of a chelation therapy for Chronic Beryllium Disease (CBD). We describe a procedure for the direct determination of beryllium in undigested micro quantities of human blood and serum using graphite furnace atomic absorption spectrometry. Blood and serum samples are prepared respectively by a simple 8-fold and 5-fold dilution with a Nash Reagent. Three experimental setups are compared: using no modifier, using magnesium nitrate and using palladium/citric acid as chemical modifiers.

Results

In serum, both modifiers did not improve the method sensitivity, the optimal pyrolysis and atomization temperatures are 1000°C and 2900°C, respectively. In blood, 6 μg of magnesium nitrate was found to improve the method sensitivity. The optimal pyrolysis and atomization temperatures were 800°C and 2800°C respectively.

Conclusion

In serum, the method detection limit was 2 ng l^-1, the characteristic mass was 0.22 (± 0.07) pg and the accuracy ranged from 95 to 100%. In blood, the detection limit was 7 ng l^-1, the characteristic mass was 0.20 (± 0.02) pg and the accuracy ranged from 99 to 101%.     

Mechanism of vaporization of yttrium and rare earth elements in electrothermal vaporization inductively coupled plasma mass spectrometry

The mechanism of vaporization of yttrium and the rare earth elements (REEs) has been studied using graphite furnace atomic absorption spectrometry (GFAAS) and inductively-coupled plasma mass spectrometry (ICP-MS). The appearance temperatures for Y and the REEs obtained by GFAAS were generally identical to the appearance temperatures obtained using ETV-ICP-MS. At lower temperatures, Y and the REEs are predominantly vaporized in atomic form or as oxides, while at temperatures above 2500°C, the elements are vaporized as oxides and/or carbides. This accounts for the very high sensitivity of ETV-ICP-MS compared to GFAAS for the determination of these elements. Absolute limits of detection for Y and all of the REEs using ETV-ICP-MS ranged from 0.002 pg for Tm to 0.2 pg for Ce. The use of freon as a chemical modifier was effective in controlling analyte carbide formation and reducing memory effects.     

A critical evaluation of the graphite furnace conditions for the direct determination of chromium in urine

A critical study of the conditions for the direct determination of Cr in urine using GFAAS was carried out. A chemometric approach showed that the most important parameters that influence the efficiency of atomic Cr cloud formation were the atomization from the tube wall and the proper implementation of a pyrolysis step. The established procedure does not require any sample pre-treatment thus minimizing the risk of contamination. The Cr content in urine was determined using a calibration curve prepared with Cr spiked urine, easily correcting all potential matrix interferences. The heating program proposed took 68 s for a 30 μL urine sample. The procedure was applied for the determination of Cr in urine to investigate the absorption rate of Cr picolinate. The limit of detection and the characteristic mass for a 30 μL urine sample were 0.18 μg/L and 5.4 pg, respectively.     

Direct Determination of Arsenic in Beet Sugar Molasses Using Nickel as Chemical Modifier by Electrothermal Atomic Absorption Spectrommetry

A simple electrothermal atomic absorption spectrometric (ETAAS) method is described for direct determination of arsenic in sugar beet molasses samples. Pyrolytic graphite tubes were used as atomizers. The compression between modifiers such as nickel nitrate, palladium nitrate and the mixture of palladium and magnesium nitrate were performed and nickel nitrate selected as the best chemical modifier. The effects of pyrolysis and atomization temperature were also studied and the pyrolysis temperature of 900 °C and atomization temperature of 2300 °C have been chosen for temperature program. The detection limit of the method was 1 ng/mL As in sugar beet molasses samples. The relative standard deviation for ten determination of a spiked sample with concentration of 50 ng/mL As was 2.4%. The accuracy of the method was confirmed by the analysis of spiked samples. The linear rang of calibration is in the range of 1‐100 ng/mL of arsenic.     

Selenium determination in tissue samples of Nile tilapia using ultrasound-assisted extraction

This paper proposes a method to determine selenium in samples of fish muscle and liver tissue using ultrasound assisted extraction process, and analysed by graphite furnace atomic absorption spectrometry (GFAAS). The selenium content was extracted by 0.10 M HCl at the optimal extraction conditions which were established as follows: sample mass of 100 mg; granulometry of the sample <60 μm; sonication time of five 40 s cycles; and sonication power of 136 W. The selenium determinations were performed by GFAAS, at a drying temperature of 120°C/250°C, pyrolysis temperature of 1300°C, atomization temperature of 2300°C, and cleaning temperature of 2800°C. Palladium nitrate was used as a chemical modifier coinjected with the samples, and tungsten as a permanent modifier. The concentration of selenium determined in the pool of fish muscle and liver tissue were 280.4±4.2 e 592.3±6.7 μg kg⁻¹, respectively. The accuracy and precision of the proposed extraction method were evaluated using certified standard Bovine Muscle — NIST 8414. The results obtained by the ultrasonic extraction method were equivalent to those obtained by the method of acid mineralization of samples in a microwave oven     

A critical evaluation of the graphite furnace conditions for the direct determination of chromium in urine

A critical study of the conditions for the direct determination of Cr in urine using GFAAS was carried out. A chemometric approach showed that the most important parameters that influence the efficiency of atomic Cr cloud formation were the atomization from the tube wall and the proper implementation of a pyrolysis step. The established procedure does not require any sample pre-treatment thus minimizing the risk of contamination. The Cr content in urine was determined using a calibration curve prepared with Cr spiked urine, easily correcting all potential matrix interferences. The heating program proposed took 68 s for a 30 μL urine sample. The procedure was applied for the determination of Cr in urine to investigate the absorption rate of Cr picolinate. The limit of detection and the characteristic mass for a 30 μL urine sample were 0.18 μg/L and 5.4 pg, respectively. Received: 22 June 1998 / Revised: 13 January 1999 / Accepted: 18 January 1999     

Determination of cadmium in coal using solid sampling graphite furnace high-resolution continuum source atomic absorption spectrometry

This work describes the development of a method to determine cadmium in coal, in which iridium is used as a permanent chemical modifier and calibration is performed against aqueous standards by high-resolution continuum source atomic absorption spectrometry (HR-CS AAS). This new instrumental concept makes the whole spectral environment in the vicinity of the analytical line accessible, providing a lot more data than just the change in absorbance over time available from conventional instruments. The application of Ir (400 g) as a permanent chemical modifier, thermally deposited on the pyrolytic graphite platform surface, allowed pyrolysis temperatures of 700 °C to be used, which was sufficiently high to significantly reduce the continuous background that occurred before the analyte signal at pyrolysis temperatures <700 °C. Structured background absorption also occurred after the analyte signal when atomization temperatures of >1600 °C were used, which arose from the electron-excitation spectrum (with rotational fine structure) of a diatomic molecule. Under optimized conditions (pyrolysis at 700 °C and atomization at 1500 °C), interference-free determination of cadmium in seven certified coal reference materials and two real samples was achieved by direct solid sampling and calibrating against aqueous standards, resulting in good agreement with the certified values (where available) at the 95% confidence level. A characteristic mass of 0.4 pg and a detection limit of 2 ng g^–1, calculated for a sample mass of 1.0 mg coal, was obtained. A precision (expressed as the relative standard deviation, RSD) of <10% was typically obtained when coal samples in the mass range 0.6–1.2 mg were analyzed.Dedicated to the memory of Wilhelm Fresenius     

Direct determination of germanium in botanical samples by graphite furnace atomic absorption spectrometry with palladium-zirconium as chemical modifier

A method has been described for the direct determination of trace levels of germanium by graphite furnace atomic absorption spectrometry (GFAAS) using chemical matrix modification technique. The stabilization and the pyrolysis temperatures for germanium were investigated with various chemical modifiers including palladium, palladium–magnesium, palladium–strontium and palladium–zirconium. The highest pyrolysis temperature and highest integrated absorbance were obtained using palladium–zirconium modifier, and the severe matrix interference from sulfate can be eliminated. The characteristic mass and absolute detection limit (3σ) of germanium were found to be 16 and 12 pg, respectively. The proposed method was applied to the determination of trace levels of germanium in botanical samples with a recovery range of 92–106%. The hydride generation atomic fluorescence spectrometric (HGAFS) method was employed to analyze the samples and the results agree well with those obtained by GFAAS. The contents of germanium in standard reference materials were determined and the results were in good agreement with the reference values.     

Comparative study of conventional and multivariate methods for aluminum determination in soft drinks by graphite furnace atomic absorption spectrometry

In the present study, conventional and multivariate methods were used to optimize conditions for direct determination of aluminum in soft drinks by electrothermal atomic absorption spectrometry. For the conventional method, the optimized experimental parameters were: pyrolysis and atomization temperatures and chemical modifier. A multivariate study was performed using factorial design and the optimized parameters were the same employed in the univariate method including pyrolysis time. For the conventional method, the optimal conditions obtained were: pyrolysis temperature of 1600 °C, atomization temperature of 2700 °C, and Zr as permanent modifier. For the factorial design in the multivariate optimization, the Pareto´s chart showed that the atomization temperature, the modifier, and the pyrolysis temperature presented a significant effect on the integrated absorbance and the interaction between pyrolysis temperature and pyrolysis time also had a significant effect on the signal. Better results were obtained using Zr as modifier. The surface response indicates that the lowest pyrolysis (1100 °C) and atomization temperatures (2350 °C) provide higher absorbance for aluminum in soft drinks. Characteristic mass of 23.4 and 19.4 pg and LOD of 17.9 and 11.3 μg L^− 1 was obtained to conventional and multivariate methods, respectively. The calibration was accomplished with standard addition in a range of 60–200 μg L^− 1 for conventional method and of 38–200 μg L^− 1for multivariate method with R higher than 0.99 for both conditions. Recoveries in both studies were nearly 100% with adequate precision for GFAAS analysis. For the Al concentrations level found in soft drinks, both experimental conditions are adequate as good results were obtained in recovery studies. The Al concentrations in different soft drinks range from 147.9 to 599.5 μg L⁻¹. Higher concentrations were found in soft drinks sold in Al cans than in PET bottles, indicating that contamination can occur.     

Chemical modifiers for direct determination of cobalt in coal combustion residues by ultrasonic slurry-sampling-ETAAS

Five modifiers were tested for the direct determination of cobalt in coal fly ash and slag by ultrasonic slurry-sampling electrothermal atomic absorption spectrometry (USS-ETAAS).The furnace temperature programs and the appropriate amount for each modifier were optimized to get the highest signal and the best separation between the atomic and background signals. Nitric acid (0.5% v/v) was the most adequate chemical modifier for cobalt determination, selecting 1,450 degrees C and 2,100 degrees C as pyrolysis and atomization temperatures, respectively. This modifier also acts as liquid medium for the slurry simplifying the procedure. The remaining modifiers enhanced the background signal, totally overlapped with cobalt peak. The method optimized gave a limit of detection of 0.36 microg g(-1), a characteristic mass of 13 +/- 1 pg and an overall-method precision which is highly satisfactory (<7%, RSD). The method was validated by analyzing two certified coal fly ash materials, and satisfactory recoveries were obtained (83-90%) and no statistical differences were observed between the experimental and the certified cobalt concentrations. Additionally, certified sediment, soil and urban particulate matter were assayed; again good results were obtained. The developed methodology was used to determine cobalt in several coal combustion residues from five Spanish power plants.     

Heated Slurry Sampling for the Determination of Cadmium in Food by Electrothermal Atomic Absorption Spectrometry

A heating procedure is reported with slurry sampling electrothermal atomic absorption spectrometry to improve the accuracy of cadmium determination in food. In comparison to conventional slurry sampling, the heating significantly increased cadmium recovery and improved the precision. For the optimized procedure, 25–250 mg of food were treated with 2% HNO₃ and 1% H₂O₂ with heating at 120°C for 20 min, followed by the addition of 50 µL of 10% Triton X-100, and homogenization in an ultrasonic bath prior to analysis. Tungsten and rhodium were employed as a permanent modifier with optimum pyrolysis and atomization temperatures of 500°C and 1500°C. Calibration with aqueous standards resulted in good agreement between certified or information values and measured results at the 95% confidence level. A characteristic mass of 0.8 ± 0.1 pg and a detection limit of 0.7 ng g^?1 for a 2% slurry were obtained. The method was employed for the direct determination of cadmium in food certified reference materials.     

Determination of Bismuth in Sediment and Soil by Ultrasonic Slurry Sampling Electrothermal Atomic Absorption Spectrometry

The analytical conditions of the direct determination of bismuth in some certified reference material samples (soil and sediment) by slurry sampling Zeeman electrothermal atomic absorption spectrometry (ETAAS) with the use of automated ultrasonic slurry mixing are discussed. Palladium nitrate was used as a chemical modifier. With the use of this modifier it was possible to stabilize bismuth to the pyrolysis temperature of 1300 °C. Platform atomization was performed at 2050 °C. The results of determination are calculated from a simple, aqueous standards based calibration graph. Statistical evaluation of the results indicate that the slurry sampling method is reproducible and the accuracy of the proposed method is very good. This method is rather simple and its other advantages are good sensitivity and relatively short analysis time.     

Direct determination of parts-per-billion levels of germanium in botanical samples and coal fly ash by graphite furnace atomic absorption spectrometry

 Parts-per-billion levels of germanium can be determined directly by graphite furnace atomic absorption spectrometry (GFAAS) using palladium plus strontium as a mixed modifier resulting in pyrolysis temperatures up to 1400 °C without loss of germanium. At this temperature the matrix effect including the most troublesome sulfate interference can be eliminated. Palladium plus strontium nitrate is advantageous compared to palladium alone or palladium plus magnesium nitrate; an amount of 15 μg of sulfate does not show any interference on the determination of 1 ng of germanium. The method was successfully applied to the determination of ng/g levels of germanium in botanical samples and coal fly ash after thermal decomposition of the samples in a mixture of acids using a pressure bomb. The results were consistent with the reference values given for botanical samples and coal fly ash with a recovery range of 96.4∼103.4% Received: 16 September 1996/Revised: 10 December 1996/Accepted: 14 January 1997     

Investigation of chemical modifiers for phosphorus in a graphite furnace using high-resolution continuum source atomic absorption spectrometry

Phosphorus is not one of the elements that are typically determined by atomic absorption spectrometry, but this technique nevertheless offers several advantages that make it attractive, such as the relatively great freedom from interferences. As the main resonance lines for phosphorus are in the vacuum–ultraviolet, inaccessible by conventional atomic absorption spectrometry equipment, L´vov and Khartsyzov proposed to use the non-resonance doublet at 213.5 / 213.6 nm. Later it turned out that with conventional equipment it is necessary to use a chemical modifier in order to get reasonable sensitivity, and lanthanum was the first one suggested for that purpose. In the following years more than 30 modifiers have been proposed for the determination of this element, and there is no consensus about the best one. In this work high-resolution continuum source atomic absorption spectrometry has been used to investigate the determination of phosphorus without a modifier and with the addition of selected modifiers of very different nature, including the originally recommended lanthanum modifier, several palladium-based modifiers and sodium fluoride. As high-resolution continuum source atomic absorption spectrometry is revealing the spectral environment of the analytical line at high resolution, it became obvious that without the addition of a modifier essentially no atomic phosphorus is formed, even at 2700 °C. The absorption measured with line source atomic absorption spectrometry in this case is due to the PO molecule, the spectrum of which is overlapping with the atomic line. Palladium, with or without the addition of calcium or ascorbic acid, was found to be the only modifier to produce almost exclusively atomic phosphorus. Lanthanum and particularly sodium fluoride produced a mixture of P and PO, depending on the atomization temperature. This fact can explain at least some of the discrepancies found in the literature and some of the phenomena observed in the determination of phosphorus using line source atomic absorption spectrometry.     

Factorial and Doehlert Design Used as Optimization Procedures for the Direct Determination of Lead in Whole Blood Samples by Graphite Furnace Atomic Absorption Spectrometry

In this work, the direct determination of lead in whole blood samples by graphite furnace atomic absorption spectrometry is proposed. The samples were diluted 1:9 with HNO₃ and Triton® X-100, both 0.2% v/v. Multivariate optimization was made to evaluate the pyrolysis and atomization temperatures and the use of a chemical modifier. The method allowed lead determination with a curve ranging from 0 to 6.0 μg dL^?1. Recovery studies presented results from 88 to 109%. The LOD and the characteristic mass were 0.21 μg dL^?1 and 7.4 pg, respectively. Intra- and inter-assay studies showed respective coefficients of variation of 4.2 and 8.9%.