The meaning of ‘concentration’

Terminology within a small laboratory community can be informal without danger of misunderstanding, but communication with a wider audience and not least in publications, needs unequivocal terms for defined concepts. As an example, the many meanings of “concentration” are explored to present a systematic nomenclature, including a concept diagram.

Influence of valence and concentration of electrolytes on the ζ-potential of polyacrylic lattices

The -potential of copolymer particles of acrylic amide, acrylic acid, acrylic butyl ester, and styrene were measured in different electrolyte solutions. In an isotonic solution of sodium chloride, they vary with the content of acrylic acid between –36 mV and –49 mV. In the presence of 21-electrolytes, the -potential could be correlated with the logarithm of the electrolyte concentration. The 21-electrolytes predominantly determine the -potential of the particles not only in the solutions of these electrolytes, but also in mixed electrolyte solutions. In the presence of human serum, the electrophoretic mobility increases with increasing acrylic acid content of the polymer.     

Production of biosurfactants through biodesulfurization of spent engine oil – an experimental study

Spent engine oil, a mixture of aliphatic and aromatic compounds, is one of the frequent environmental pollutants. In this paper, biodesulfurization of spent oil using Rhodococcus sp. was studied. Batch studies were conducted varying the oil to aqueous medium ratio of 10:90 to 90:10. The results demonstrated that maximum desulfurization of 80% was obtained at the oil to aqueous phase ratio of 70:30. Kinetic parameters of Monod type growth model, namely, µ_max, maximum specific growth rate and K_s, the half saturation constant were determined by varying the initial sulfur content of spent oil in the range of 0.16–1.05% (w/v). Gas chromatography–mass spectrometry was done to identify the compounds present in treated and untreated spent engine oil. The surface tension and emulsification indices of both oil and aqueous phases were also determined at different reaction times.     

Influence of base fluid,temperature, and concentration on the thermophysical properties of hybrid nanofluids of alumina–ferrofluid: experimental data,modeling through enhanced ANN,ANFIS, and curve fitting

Journal of Thermal Analysis and Calorimetry - Recently, the suspension of hybrid nanoparticles in conventional fluids has been investigated as a technique for improving the thermophysical...     

Influence of Fe concentration on the properties of the electrodeposited Zn–Fe coatings

Electrodeposition of Zn–Fe alloys on a copper substrate from a sulfate bath with different Fe²⁺ concentration (0.05, 0.10 and 0.20 mol L^?1) at room temperature was investigated using cyclic voltammetry. The influence of the Fe²⁺ content in the plating bath on the surface morphology, structural and magnetic properties of the coatings were characterized using scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), X-ray diffraction (XRD) and Vibrating Sample Magnetometer (VSM). The results show that the morphology of Zn–Fe films changes with different Fe²⁺ concentration. The EDS analysis demonstrated that the Fe content of the coatings increased with increasing the Fe concentration in the bath. XRD measurements shows the presence of ?Zn (hcp), δ1ZnFe (hcp) and the ΓZnFe (bcc) phases with a (101) preferential orientation in all the electrodeposited films. The magnetic analysis of Zn–Fe films indicated that the saturation magnetization was largely enhanced in comparison to pure Zn, especially with 0.2 at. % Fe, while the coercivity decreased.     

Study of the surface properties and surface concentration of ionic liquid–alcohol mixtures

Surface properties for three binary mixtures containing a 1-butyl-3-methylimidazolium thiocyanate ([BMIM][SCN]) and a long-chain alcohol (1-butanol, 1-pentanol and 1-hexanol) were determined by surface tension data at the following temperatures: (298.15, 308.15, 318.15, 328.15 and 338.15) K. The surface tension data over the entire mole fraction range are correlated by the Fu et al.(FLW) and Myers-Scott (MS) models. There is good agreement between the experimental data and the results of correlations for 15 binary systems (the three systems at five temperatures) with an average relative error below 1.5%. In addition, the UNIFAC group contribution method is applied for calculation of activity coefficients of components in solution. Moreover, the relative adsorptions of alcohol at the air/liquid interface are determined using Gibbs adsorption isotherm. The obtained results show that the values of adsorption for mixtures of alcohols/[BMIM][SCN] increase with increasing the alkyl chain length of alcohol and decreasing temperature.     

Comparative theoretical and experimental analysis of hydrocarbon σ-radical cations

The structures of σ-radical cations formed by ionization of adamantane, twistane, noradamantane, cubane, 2,4-dehydroadamantane, and protoadamantane were optimized at the B3LYP, B3LYP-D, M06-2X, B3PW91, and MP2 levels of theory using 6-31G(d), 6-311+G(d,p), 6-311+G(3df,2p), cc-PVDZ, and cc-PVTZ basis sets. On the whole, single-configuration approximations consistently describe the structure and transformations of the examined σ-radical cations. The best correlations (r = 0.97–0.98) between the calculated adiabatic ionization potentials and experimental oxidation (anodic) potentials of hydrocarbons were obtained in terms of B3PW91 approximation.     

Response of peptide intensity to concentration in ESI–MS-based proteome

High-throughput quantification with label-free methods has received considerable attention in electrospray ionization(ESI)-mass spectrometry(MS),but the manner by which MS signals respond to peptide concentration remains unclear in proteomics.We developed a new mathematical formula to describe the intrinsic log-log relationship between the MS intensity response and peptide concentration in an analytical ESI process.Experimental results showed that the calibration curve is fairly fit to the log-log formula with a linear dynamic range of approximate four to five orders of magnitude.However,we found that the ionization of analytical peptides can be severely suppressed by coexisting matrix peptides,such that the calibration curve can be poorly leveled off on both ends.Our study suggests that the interferences from coexisting matrix peptides should be reduced in the ESI process to use the log-log calibration curve successfully for the high-throughput quantification.     

Features of charge carrier concentration and mobility in π-conjugated polymers

We show the possibilities of experimental investigation of charge carrier mobility and concentration features by extraction methods of equilibrium, photoexcited and injected charge carriers in π-conjugated polymers, where, due to relatively high conductivity, the classic time-of-flight method is inappropriate.     

Influence of phosphorus concentration on the state of the surface layer of Pd–P hydrogenation catalysts

Phase composition and surface layer state of the Pd–P hydrogenation catalyst formed at various P/Pd ratios from Pd(acac)₂ and white phosphorus in a hydrogen atmosphere were determined. Palladium on the catalyst surface is mainly in two chemical states: as Pd(0) clusters and as palladium phosphides. As the P/Pd ratio increases, the fraction and size of palladium clusters decrease, and also the phase composition of formed palladium phosphides changes: Pd₃P_0.8 → Pd₅P₂ → PdP₂. The causes of the modifying action of phosphorus on the properties of palladium catalysts for hydrogenation of unsaturated compounds were considered.     

Influence of dose and ion concentration on formation of binary Al–Ni alloy nanoclusters

Colloidal Al–Ni nanoclusters were prepared in an aqueous polyvinyl alcohol solution containing aluminum chloride and nickel chloride as metal precursors, polyvinyl alcohol as a capping agent, isopropanol as a scavenger of hydroxyl radicals, and distilled water as a solvent. Gamma irradiations were carried out in a ⁶⁰Co gamma source chamber at doses up to 100 kGy. The nanocluster properties were characterized by transmission electron microscopy (TEM), UV–visible spectrophotometry, and X-ray diffraction (XRD). By controlling the dose and precursor concentration, nanoclusters with different particle sizes were obtained. The average particle diameter increased with increase of precursor concentration and decreased with increase of dose. This is owing to the competition between nucleation, growth, and aggregation processes in the formation of nanoclusters during irradiation.     

Preparation of spherical silica particles by Stöber process with high concentration of tetra-ethyl-orthosilicate

In this paper, Stöber process with high concentration of tetra-ethyl-orthosilicate (TEOS) up to 1.24 M is used to prepare monodisperse and uniform-size silica particles. The reactions are carried out at [TEOS] = 0.22–1.24 M, low concentrations of ammonia ([NH₃] = 0.81[TEOS]), and [H₂O] = 6.25[TEOS] in isopropanol. The solids content in the resulting suspension achieves a maximum value of 7.45% at 1.24 M TEOS. Various-sized particles in the range of 30–1000 nm are synthesized. The influences of TEOS, NH₃, and H₂O on the size and size distribution of the particles are discussed. A modified monomer addition model combined with aggregation model is proposed to analyze the formation mechanism of silica particles.     

Theoretical and experimental investigations of the enantioselective epoxidation of olefins catalyzed by manganese complexes

The enantioselective epoxidation of olefin by Mn^II（R,R-PMCP）(OTf)2, H₂O₂ and H₂SO₄ was explored by DFT calculations and experiments. Theoretical results suggest that [MnV（O）(R,R-PMCP)（SO4）]+species with a triplet ground spin state serves as the active species for the olefin epoxidation. It can be generated by the H₂SO₄ assisted O-O heterolysis of Mn^III（OOH） species. Mn^III-persulfate is also involve...     

Influence of cerium concentration on the structure and properties of silica-methacrylate sol–gel coatings

The aim of this work was to study the effect of the incorporation of cerium nitrate in a silica-methacrylate sol–gel hybrid matrix reinforced with silica nanoparticles. Sols, coatings and powders have been studied, focusing specially in the determination of the redox ratio Ce³⁺/Ce⁴⁺ and films structure. Sols have been characterised using viscosity measurements and FT-IR spectroscopy, and powders and coatings obtained with different Ce contents through UV–Vis and FT-IR spectroscopy, TGA, TEM, AFM and FE-SEM. The goal was to reach the best compromise between maximum cerium concentration and coating stability to better understand the mechanisms acting in active anti-corrosive processes.     

Towards a consistent mechanism of emulsion polymerization—new experimental details

The application of atypical experimental methods such as conductivity measurements, optical microscopy, and nonstirred polymerizations to investigations of the ‘classical’ batch ab initio emulsion polymerization of styrene revealed astonishing facts. The most important result is the discovery of spontaneous emulsification leading to monomer droplets even in the quiescent styrene in water system. These monomer droplets with a size between a few and some hundreds of nanometers, which are formed by spontaneous emulsification as soon as styrene and water are brought into contact, have a strong influence on the particle nucleation, the particle morphology, and the swelling of the particles. Experimental results confirm that micelles of low-molecular-weight surfactants are not a major locus of particle nucleation. Brownian dynamics simulations show that the capture of matter by the particles strongly depends on the polymer volume fraction and the size of the captured species (primary free radicals, oligomers, single monomer molecules, or clusters).     

Direct experimental detection of hydrogen radicals in non-oxidative methane catalytic reaction

Non-oxidative conversion of methane to olefins,aromatics and hydrogen(MTOAH) has been reported recently over metal single sites such as iron and platinum.The reaction was proposed to involve catalytic activation of methane followed by gas phase C-C coupling of methyl radicals.This study using H atom Rydberg Tagging time-of-flight technique provides direct experimental evidence for the formation of hydrogen radicals during MTOAH reaction over a catalytic quartz wall reactor containing embedded iron species(denoted as Fe-reactor).Fe-reactor gives 7.3% methane conversion at 1273 K with 41.2% selectivity toward C2(ethane,ethylene and acetylene) and 31.8% toward BTX(benzene,toluene and xylene),respectively.The enhancing effects of hydrogen radicals on overall MTOAH performance are validated by cofeeding hydrogen donor benzene,which provides an additional route of methane activation apart from catalytic activation.     

The low concentration aggregation of sodium oleate–sodium linoleate aqueous mixtures

Sodium oleate (NaOL, C₁₈H₃₃O₂Na)–sodium linoleate (NaLin, C₁₈H₃₁O₂Na) mixtures were studied in the micellar and in the air/water interface states at 298.15 K. Three aggregation steps were found: a premicellar aggregation, the critical micelle concentration (CMC), and a structural change of micelles. Micelles, both at the CMC and at the structural change concentration, are richer in oleate than the overall mixture composition. Micelles are strongly non-ideal and the interaction is repulsive. The non-ideal behavior and the dependence of the micelle ionization degree with micelle composition are explained on the basis of the interaction of the π electrons of the surfactants’ chains with water at the hydrocarbon/water micellar interface. The air/solution adsorbed monolayer is also non-ideal, but the interaction is attractive and there is a preferential composition with a mole fraction of sodium oleate of about 0.7. The surface pseudophase behaves as if oleate were the solvent and linoleate a strongly soluble solute. This behavior and the dependence of the average area per adsorbed molecule were explained on the basis of the interaction of the double bonds with water. At the air/solution interface, the linoleate molecule area was similar to that of a heterogemini surfactant having a spacer with seven carbon atoms.     

Effect of concentration on surfactant micelle shapes —A molecular dynamics study

Many aspects of the behavior of surfactants have not been well understood due to the coupling of many different mechanisms. Computer simulation is, therefore, attractive in the sense that it can explore the effect of different mechanisms separately. In this paper, the shapes, structures and sizes of sodium dodecylbenzenesulfonate (SDBS) micelles under different concentrations in an oil/water mixture were studied via molecular dynamics (MD) simulations using a simplified atomistic model which basically maintains the hydrophile and lipophile properties of the surfactant molecules. Above the critical micellar concentration (cmc), surfactant molecules aggregate spontaneously to form a wide variety of assemblies, from spherical to rodlike, wormlike and bilayer micelles. Changes in their ratios of the principle moments of inertia (g₁/g₃, g₂/g₃) indicated the transition of micelle shapes at different concentrations. The aggregation number of micelle is found to have a power-law dependence on surfactant concentration.     

Molecular interpretation of the main relaxations found ID dielectric spectra of cellulose – experimental arguments

ID dielectric spectra of cellulose two relaxation processes dominate ID the low temperature range (–120 °C–0 °C). For application of the dielectric method as a diagnostic tool, these relaxations must be assigned to molecular motions of the polymeric system. This paper summarizes and discusses all experimental facts found by dielectric spectroscopy, which can help to solve this interpretation problem. ID ID necessary to include two other relaxation processes ID this discussion: the _wet- relaxation found ID all wet materials and the -relaxation evidently found ID all derivatives. The main result of our investigations ID that the dominant process ID the dielectric spectra at low temperatures (called -relaxation) ID the segmental motion of the chain and not methylol side-group reorientation. Additionally, for the first time, the dielectric spectra of Valonia (and also of bacterial cellulose) clearly indicate that the methylol side-group relaxation ID represented ID the dielectric spectra of pure polysaccharides. This -process ID only masked by the -process for the most pure celluloses. For low molecular weight saccharides and derivatives of cellulose both processes are simultaneously found ID the dielectric spectra. For the first time a correlation ID presented between the intensity of the local motion mode (-relaxation) and the degree of crystallinity for various cellulosic materials.     

An experimental study of the stability of TiO2 particles in organic–water mixtures

The stability of TiO₂ (Anatase) particles in various organic-water mixtures is examined experimentally. The results obtained reveal that the addition of AlCl₃ to a methanol–water dispersion leads to charge reversal on particle surface. If the concentration of methanol is high, CaCl₂ also leads to charge reversal, but NaCl does not have this effect. This implies that if the concentration of methanol is low, the coagulation between TiO₂ particles is due to double-layer compression for Na⁺ and Ca²⁺, and due to charge adsorption and neutralization for Al³⁺. A methanol dispersion is unstable without the addition of electrolyte, and the addition of both CaCl₂ and AlCl₃ has the effect of stabilizing the dispersion; the addition of NaCl does not have this effect. The qualitative behaviors of an acetone–water dispersion are similar to those of a methanol–water dispersion. It is interesting to observe, however, that the absolute mobility of a pure acetone dispersion has a maximum as the concentrations of both CaCl₂ and AlCl₃ vary, but charge reversal does not occur. Among the dispersions without the addition of electrolyte, a 50% organic–water mixture is most stable. Also, a methanol–water dispersion is more stable than an acetone–water dispersion, which can be explained based on the degree of dissociation of an electrolyte.