In vitro study of magnetic particle seeding for implant assisted-magnetic drug targeting

The concept of using magnetic particles (seeds) as the implant for implant assisted-magnetic drug targeting (IA-MDT) was analyzed in vitro. Since this MDT system is being explored for use in capillaries, a highly porous (ε∼70%), highly tortuous, cylindrical, polyethylene polymer was prepared to mimic capillary tissue, and the seeds (magnetite nanoparticles) were already fixed within. The well-dispersed seeds were used to enhance the capture of 0.87 μm diameter magnetic drug carrier particles (MDCPs) (polydivinylbenzene embedded with 24.8 wt% magnetite) under flow conditions typically found in capillary networks. The effects of the fluid velocity (0.015–0.15 cm/s), magnetic field strength (0.0–250 mT), porous polymer magnetite content (0–7 wt%) and MDCP concentration (C=5 and 50 mg/L) on the capture efficiency (CE) of the MDCPs were studied. In all cases, when the magnetic field was applied, compared to when it was not, large increases in CE resulted; the CE increased even further when the magnetite seeds were present. The CE increased with increases in the magnetic field strength, porous polymer magnetite content and MDCP concentration. It decreased only with increases in the fluid velocity. Large magnetic field strengths were not necessary to induce MDCP capture by the seeds. A few hundred mT was sufficient. Overall, this first in vitro study of the magnetic seeding concept for IA-MDT was very encouraging, because it proved that magnetic particle seeds could serve as an effective implant for MDT systems, especially under conditions found in capillaries.     

In vitro study of magnetic nanoparticles as the implant for implant assisted magnetic drug targeting

Magnetic nanoparticle (MNP) seeds were studied in vitro for use as an implant in implant assisted-magnetic drug targeting (IA-MDT). The magnetite seeds were captured in a porous polymer, mimicking capillary tissue, with an external magnetic field (70 mT) and then used subsequently to capture magnetic drug carrier particles (MDCPs) (0.87 μm diameter) with the same magnetic field. The effects of the MNP seed diameter (10, 50 and 100 nm), MNP seed concentration (0.25-2.0 mg/mL), and fluid velocity (0.03-0.15 cm/s) on the capture efficiency (CE) of both the MNP seeds and the MDCPs were studied. The CE of the 10 nm MNP seeds was never more than 30%, while those of the 50 and 100 nm MNP seeds was always greater than 80% and in many cases exceeded 90%. Only the MNP seed concentration affected its CE. The 10 nm MNP seeds did not increase the MDCP CE over that obtained in the absence of the MNP seeds, while the 50 and 100 nm MNP seeds increased significantly, typically by more than a factor of two. The 50 and 100 nm MNP seeds also exhibited similar abilities to capture the MDCPs, with the MDCP CE always increasing with decreasing fluid velocity and generally increasing with increasing MNP seed concentration. The MNP seed size, magnetic properties, and capacity to self-agglomerate and form clusters were key properties that make them a viable implant in IA-MDT.     

Synthesis of α-Fe2O3 nanobelts and nanoflakes by thermal oxidation and study to their magnetic properties

α-Fe₂O₃ nanobelts and nanoflakes have been successfully synthesized by oxidation of iron-coated ITO glass in air. The X-ray diffraction, Raman spectrum and scanning electron microscopy are carried out to characterize the nanobelts and nanoflakes. The formation mechanism has been presented. Significantly, the magnetic investigations show that the magnetic properties are strongly shape-dependent. The magnetization measurements of belt-like and flake-like α-Fe₂O₃ in perpendicular exhibit ferromagnetic feature with the coercivity (H_c) and saturation magnetization (M_s) of 334.5 Oe and 1.35 emu/g, 239.5 Oe and 0.12 emu/g, respectively. For the parallel, belt-like and flake-like α-Fe₂O₃ also exhibit ferromagnetic feature with the H_c and M_s of 205.5 Oe and 1.44 emu/g, 159.6 Oe and 0.15 emu/g, respectively.     

Large magnetic entropy change and refrigerant capacity in rare-earth intermetallic RCuAl (R=Ho and Er) compounds

The magnetic properties and the magnetocaloric effects of RCuAl (R=Ho and Er) compounds have been investigated. Both HoCuAl and ErCuAl just undergo a second-order ferromagnetic–paramagnetic phase transition at T_C. Large reversible magnetic entropy changes (ΔS_M) are observed around their respective Curie temperatures due to the ferromagnetic–paramagnetic phase transition. For a field change of 0–5 T, the peak values of −ΔS_M of RCuAl (R=Ho and Er) compounds are 23.9 and 22.9 J kg⁻¹ K⁻¹ at T_C, with the values of refrigerant capacity of 393 and 321 J kg⁻¹, respectively. These properties suggest that RCuAl (R=Ho and Er) compounds could be considered as attractive magnetic refrigerants working in low temperature range.     

Magnetic structure of the Mn5Si3-type Er5Ge3 compound

The Er₅Ge₃ compound (Mn₅Si₃-type, hP16, P6₃/mcm) at 4 K shows magnetic ordering of the antiferromagnetic type. Its magnetic structure consists of sine modulated collinear magnetic moments of Er that are parallel to the c axis (with a propagation vector k=[0 0 ±0.3]). This corresponds to the magnetic unit cell (a a 10c), the values of the magnetic moment of the Er atoms being, as a general formula, M_z≈M₀ cos [2π(Z–1/4)(1–kZ)], with M₀=9.2(2) μ_B at 4 K.     

Four-fold magnetic anisotropy in a Co film on MgO(0 0 1)

The development of devices based on magnetic tunnel junctions has raised new interests on the structural and magnetic properties of the interface Co/MgO. In this context, we have grown ultrathin Co films (≤30 Å) by molecular-beam epitaxy on MgO(0 0 1) substrates kept at different temperatures (T_S). Their structural and magnetic properties were correlated and discussed in the context of distinct magnetic anisotropies for Co phases reported in the literature. The sample characterization has been done by reflection high energy electron diffraction, magneto-optical Kerr effect and ferromagnetic resonance. The main focus of the work is on a sample deposited at T_S=25 °C, as its particular way of growth has enabled a bct Co structure to settle on the substrate, where it is not normally obtained without specific seed layers. This sample presented the best crystallinity, softer magnetic properties and a four-fold in-plane magnetic anisotropy with Co〈1 1 0〉 easy directions. Concerning the samples prepared at T_S=200 and 500° C, they show fcc and polycrystalline structures, respectively and more intricate magnetic anisotropy patterns.     

Heat treatment effects on microstructure and magnetic properties of Mn-Zn ferrite powders

Mn-Zn ferrite powders (Mn_0.5Zn_0.5Fe₂O₄) were prepared by the nitrate-citrate auto-combustion method and subsequently annealed in air or argon. The effects of heat treatment temperature on crystalline phases formation, microstructure and magnetic properties of Mn-Zn ferrite were investigated by X-ray diffraction, thermogravimetric and differential thermal analysis, scanning electron microscopy and vibrating sample magnetometer. Ferrites decomposed to Fe₂O₃ and Mn₂O₃ after annealing above 550 °C in air, and had poor magnetic properties. However, Fe₂O₃ and Mn₂O₃ were dissolved after ferrites annealing above 1100 °C. Moreover, the 1200 °C annealed sample showed pure ferrite phase, larger saturation magnetization (M_s=48.15 emu g⁻¹) and lower coercivity (H_c=51 Oe) compared with the auto-combusted ferrite powder (M_s=44.32 emu g⁻¹, H_c=70 Oe). The 600 °C air annealed sample had the largest saturation magnetization (M_s=56.37 emu g⁻¹) and the lowest coercivity (H_c=32 Oe) due to the presence of pure ferrite spinel phase, its microstructure and crystalline size.     

Synthesis and surface modified hard magnetic properties in Co0.5Pt0.5 nanocrystallites from a rheological liquid precursor

Small crystallites of a metastable phase Co_0.5Pt_0.5 are precipitated by heating a rheological liquid precursor of cobalt–hydrazine complex and platinum chloride H₂PtCl₆·xH₂O in polymer molecules of poly(vinylpyrrolidone) (PVP) in ethylene glycol. The hydrazine co-reduces nascent atoms from the Co²⁺ and Pt⁴⁺ that recombine and grow as Co_0.5Pt_0.5. The PVP molecules cap a growing Co_0.5Pt_0.5 as it achieves a critical size so that it stops growing further in given conditions. X-ray diffraction pattern of a recovered powder reveals a crystalline Co_0.5Pt_0.5 phase (average crystallite size D∼8 nm) of a well-known Fm3m-fcc crystal structure with the lattice parameter a=0.3916 nm (density ρ=14.09 g/cm³). A more ordered L1₀ phase (ρ=15.91 g/cm³) transforms (D≥25 nm) upon annealing the powder at temperature lesser than 700 °C (in vacuum). At room temperature, the virgin crystallites bear only a small saturation magnetization M_s=5.54 emu/g (D=8 nm) of a soft magnet and it hardly grows on bigger sizes (D≤31 nm) in a canted ferromagnetic structure. A rectangular hysteresis loop is markedly expanded on an optimally annealed L1₀ phase at 800 °C for 60 min, showing a surface modified coercivity H_c=7.781 kOe with remnant ratio M_r/M_s=0.5564, and M_s=39.75 emu/g. Crystallites self-assembled in an acicular shape tailor large H_c from ideal single domains and high magnetocrystalline anisotropy of a hard magnet L1₀ phase.     

Influence of Nb substitution for Fe on the magnetic and magneto-impedance properties of amorphous and annealed Fe76.5−xSi13.5B9Cu1Nbx (x=0–7) ribbons

We report a systematic study of the influence of Nb substitution for Fe on the magnetic properties and magneto-impedance (MI) effect in amorphous and annealed Fe_76.5−xSi_13.5B₉Cu₁Nb_x (x=0, 1, 2, 3, 4, 5, 6, and 7) ribbons. The amorphous ribbons were annealed at different temperatures ranging from 530 to 560 °C in vacuum for different annealing times between 5 and 20 min. We have found that for the as-quenched amorphous ribbons, the substitution of Nb for Fe first increases the saturation magnetization (M_s) and decreases the coercivity (H_c) until x=3, for which the largest M_s∼152 emu/g and the smallest H_c∼1.3 Oe are obtained, then an opposite trend is found for x>3. The largest MI ratio (ΔZ/Z∼38% at f=6 MHz) is achieved in the amorphous ribbon with x=3. A similar trend has been observed for the annealed ribbons. The most desirable magnetic properties (M_s∼156 emu/g and H_c∼1.8 Oe) and the largest MI ratio (ΔZ/Z∼221% at f=6 MHz) are achieved for the x=3 sample annealed at 540 °C for 15 min. A correlation between the microstructure, magnetic properties, and MI effect in the annealed ribbons has been established.     

Perpendicular anisotropy and magneto-optical Kerr effect of (Ni/Pd) multilayers

Nickel film, with total thickness t_Ni in the range 1000-2000 Å, is known to exhibit perpendicular magnetic anisotropy (PMA), if the film has been deposited at room temperature. This phenomenon is due to the magneto-elastic (ME) effect. The same is also true for the (Ni/Pd)_n multilayers, where n is the period (n≥3). In this paper, we have made two kinds of multilayers: one, which does not have a Pd cap layer, belongs to the A-group, and the other, which has, belongs to the B-group. The polar Kerr rotation θ_k, the polar Kerr ellipticity ε_k, and the figure of merit (θ_k)²R, where R is the reflectance, were measured for the two wavelengths, i.e. λ=633 and 442 nm, respectively. The effective PMA energy K_⊥ was measured from the vibrating sample magnetometer. It was found that the most favorable multilayer for the magneto-optical (MO) application exists among the A-group samples: i.e. the t_Ni=1300 Å, t_Pd=50 Å (seed layer), and n=1 sample. We obtained θ_k=−9.76 min, ε_k=−9.13 min, (θ_k)²R=1.51 (rad)² at λ=442 nm, and K_⊥=3.21×10⁶ erg/cc for this optimal multilayer. Finally, the effects of the Pd seed layer on PMA and MO are also studied.     

Theoretic 3-D study of the high-frequency magnetic moment dynamics in thin ferromagnetic films with in-plane uniaxial anisotropy by considering eddy-current generation

In the present paper, theoretic investigations of polarisation vector precession trajectories represented by a macro spin in ferromagnetic films with in-plane uniaxial anisotropy were realised. For this purpose, the Landau–Lifschitz–Gilbert differential equation (LLG) in combination with the Maxwell equations were solved for three dimensions by considering a linear progression of the magnetisation or polarisation with an external field. The frequency and time dependent polarisation trajectories illustrate how a magnetic moment precesses if effective damping and eddy-currents impacts its motion. For computation, typical parameter values like the saturation polarisation J_s=μ₀·M_s=1.4 T and in-plane uniaxial anisotropy μ₀·H_u=4.5 mT were employed. The main focus of simulation was on the variation of the effective damping parameter α_eff between 0.01 and 0.05 and ferromagnetic film thickness t_m between 200 nm and 1200 nm. The frequency-dependent calculations were carried out between 50 MHz and 6 GHz. The time-dependent simulations were done for a duration between 5 and 30 ns.     

Structural,electronic and magnetic properties of the double perovskite Pb2FeReO6

The structural, electronic and magnetic properties of the double perovskite Pb₂FeReO₆ have been studied by using the first-principles projector augmented wave (PAW) potential within the generalized gradient approximation (GGA) as well as taking into account the on-site Coulomb repulsive and exchange coupling interactions (GGA+U). The optimized crystal structure of the Pb₂FeReO₆ is a body-centered tetragonal (BCT) with a space group of I4/m and the lattice constants of a=b=5.59 Å and c=7.93 Å, consistent with the experimental results. The two axial transition metal and oxygen (TM–O) distances are slightly larger than the four equatorial TM–O distances and shows the existence of the Jahn–Teller structural distortion in FeO₆ and ReO₆ octahedra. The Fe³⁺ and Re⁵⁺ ions are in the states (3d⁵, S=5/2) and (5d², S=1) with magnetic moments 3.929 and −0.831μ_B respectively and thus antiferromagnetic (AFM) coupling via oxygen between them. The half-metallic (HM) ferromagnetic (FM) nature implies a potential application of this new compound in magnetoelectronic and spintronics devices.     

Magnetic properties of strontium hexaferrite films prepared by pulsed laser deposition

The magnetic properties of strontium hexaferrite (SrFe₁₂O₁₉) films fabricated by pulsed laser deposition on the Si(100) substrate with Pt(111) underlayer have been studied as a function of film thickness (50–700 nm). X-ray diffraction patterns confirm that the films have c-axis perpendicular orientation. The coercivities in perpendicular direction are higher than those for in-plane direction which indicates the films have perpendicular magnetic anisotropy. The coercivity was found to decrease with increasing of thickness, due to the increasing of the grain size and relaxation in lattice strain. The 200 nm thick film exhibits hexagonal shape grains of 150 nm and optimum magnetic properties of M_s=298 emu/cm³ and H_c=2540 Oe.     

Microstructure and magnetic properties of Ni-rich Ni54Mn25.7Ga20.3 ferromagnetic shape memory alloy thin film

A Ni₅₄Mn_25.7Ga_20.3 ferromagnetic shape memory alloy thin film has been fabricated by using the RF magnetron-sputtering technique. The structure and magnetic properties of the film were systematically investigated. The results show that the film is in ferromagnetic martensite state at room temperature with the Curie temperature (T_c) of about 370 K. The saturation magnetization (M_s) of the film reaches 45 emu/g at 300 K, which is about 80% as large as that of Ni–Mn–Ga bulk material. The magnetization hysteresis loops significantly depend on temperatures. The residual magnetization (M_r) and the coercive force (H_c) increase with decreasing temperatures. The grains homogeneously distribute in the film. The microstructure of the film consists of martensite plates. The interface between the martensite variants is clear and straight, indicating a good mobility.     

I–V characteristics and critical currents in superconducting/ferromagnetic bilayers

Current–voltage (I–V) characteristics and critical current density, J_c, for the onset of vortex motion were measured at different magnetic fields, H, and temperatures, T, in a superconducting (S)/ferromagnetic (F) bilayer and in a single Nb film. We choose Nb as a superconductor and a weak ferromagnetic alloy, Pd_1−xNi_x with x = 16, as F. We found that J_c was smaller for the S/F bilayer with respect to the single Nb film. The result was related to the reduced value of the superconducting order parameter in the bilayer.     

In vitro study of ferromagnetic stents for implant assisted-magnetic drug targeting

Implant-assisted-magnetic drug targeting (IA-MDT) was studied in vitro using a coiled ferromagnetic wire stent made from stainless steel 430 or 304, and magnetic drug carrier particle (MDCP) surrogates composed of poly(styrene/divinylbenzene) embedded with 20 wt% magnetite. The fluid velocity, particle concentration, magnetic field strength, and stent material all proved to be important for capturing the MDCP surrogates. Overall, this in vitro study further confirmed the important role of the ferromagnetic implant for attracting and retaining MDCPs at the target zone.     

Critical behavior and magnetic entropy change in the La0.6Sr0.4Mn0.8Fe0.1Cr0.1O3 perovskite

Critical behavior in the La_0.6Sr_0.4Mn_0.8Fe_0.1Cr_0.1O₃ ceramics was studied using magnetization methods. Results show that the paramagnetic–ferromagnetic transition is of second order. Based on the critical behavior analysis using the Banerjee criterion and the Kouvel–Fisher method, we find the critical exponents: β=0.395±0.010, γ=1.402±0.010, and δ=5.208±0.007, for which the magnetic interaction is satisfied within the three-dimensional Heisenberg model. Results indicate the presence of short-range interactions. The magnetic entropy change (−ΔS_M) reached maximum values of 1.75, 1.45, 1.15, 0.8 and 0.43 J Kg⁻¹ K⁻¹ under a magnetic field variation of 5, 4, 3, 2 and 1 T, respectively. Nevertheless, these (−ΔS_M) values are much low for any potential application at this moment. The nature of this phenomenon is discussed in relation to the characteristics of the magnetic phase transition and critical exponents.     

Synthesis,characterization and magnetic properties of MFe2O4 (M=Co,Mg, Mn,Ni) nanoparticles using ricin oil as capping agent

We focused on obtaining MFe₂O₄ nanoparticles using ricin oil solution as surfactant and on their structural characterization and magnetic properties. The annealed samples at 500 °C in air for 6 h were analyzed for the crystal phase identification by powder X-ray diffraction using CuKα radiation. The particle size, the chemical composition and the morphology of the calcinated powders were characterized by scanning electron microscopy. All sintered samples contain only one phase, which has a cubic structure with crystallite sizes of 12–21 nm. From the infrared spectra of all samples were observed two strong bands around 600 and 400 cm⁻¹, which correspond to the intrinsic lattice vibrations of octahedral and tetrahedral sites of the spinel structure, respectively, and characteristic vibration for capping agent. The magnetic properties of fine powders were investigated at room temperature by using a vibrating sample magnetometer. The room temperature M–H hysteresis loops show ferromagnetic behavior of the calcined samples, with specific saturation magnetization (M_s) values ranging between 11 and 53 emu/g.     

Study on magnetic properties of nanocrystalline La-, Nd-, or Gd-substituted Ni–Mn ferrite at low temperatures

The effects of rare-earth ions with different radii and magnetic moments on the magnetic properties of Ni–Mn ferrite are investigated. X-ray diffraction pattern has shown the presence of cubic structure of spinel ferrite for all samples. The values of M_s and H_c are decreasing with increasing of testing temperatures for all samples. The H_c value of Ni_0.7Mn_0.3La_0.1Fe_1.9O₄ reaches 1082 Oe at 2 K. Mössbauer spectra tested at 273 K indicate the presence of superparamagnetism for samples calcined at 873 K.     

The dc magnetic field,temperature and film thickness dependence of microwave surface resistance of YBCO and DyBCO thin films

We investigated the dc magnetic field and temperature dependences of the microwave surface resistance (R_s) of YBa₂Cu₃O_y (YBCO) and DyBa₂Cu₃O_y (DyBCO) superconducting thin films. The YBCO and DyBCO thin films, each with a thickness of 300, 500, or 700 nm, were deposited on MgO (1 0 0) substrates by the thermal co-evaporation method. The R_s was measured using the dielectric resonator method. A dc magnetic field of up to 5.0 T was applied parallel to the c-axis of the superconducting thin films. The results showed that the R_s value had almost the same temperature dependence at various thicknesses in a zero-external field. The R_s of the YBCO and DyBCO thin films increased with the applied dc magnetic field. The DyBCO thin films showed weaker magnetic field dependence of R_s than the YBCO thin films. The R_s ratio (defined as R_s(5 T)/R_s(0 T)) linearly increased with the film thickness. These results show that pinning strength decreased with an increasing film thickness.