Effect of CaO on the surface morphology and strength of water soaked Na2O–B2O3–Al2O3–SiO2 vitrified bond

The surface morphology of Na₂O–B₂O₃–Al₂O₃–SiO₂ vitrified bond with and without calcium oxide was studied by soaking vitrified bonded microcrystalline alumina composites in water. The content of water introduced to the vitrified bond was determined by thermal gravity analysis, and the effects of water and calcium on the phase separation and nucleation of the vitrified bond were investigated using scanning electron microscope and energy-dispersive X-ray spectrometer. Soaked in water for 72 h, the Na₂O–B₂O₃–Al₂O₃–SiO₂ vitrified bond presented a porous surface, and its bending strength declined with increasing sintering temperature. However, the Na₂O–CaO–B₂O₃–Al₂O₃–SiO₂ vitrified bond was more durable against aqueous coolant even needle-shape crystals were found clustered on the surface of the vitrified bond. The crystals were enriched with aluminosilicate tested by energy-dispersive X-ray spectrums. The appearance of crystals lessened the dissolution of the vitrified bond and made the bending strength increase in the sintering temperature region between 870 °C and 930 °C.     

Flux growth of PbMg1/3Ta2/3O3 single crystals

Single crystals of PbMg_1/3Ta_2/3O₃ (PMT) were grown by the flux method. The PbO–Pb₃O₄–B₂O₃ system was used as a solvent. Transparent and light yellow PMT single crystals of rectangular shape and dimensions up to 10×6×4 mm³ were obtained. For the applied growth conditions only, the crystals of the perovskite structure were grown. X-ray diffraction tests showed that at room temperature PMT exhibits cubic symmetry with lattice parameter a=4.042(1) Å. Dielectric studies pointed to relaxor properties of PMT. The characteristic broad and frequency-dependent maximum of dielectric permittivity was observed at 179.7 K (1 kHz).     

Flux growth of BPO4 crystals

Single crystals of BPO₄ with sizes up to 15×10×12 mm³ were grown by top-seeded solution growth method using Li₂O–Li₄P₂O₇ as fluxes. The components volatilized from the melt were characterized by the method of X-ray powder diffraction. The defects of grown crystals have also been investigated. The measured ultraviolet cutoff edge of BPO₄ was about 130 nm. Its density was 2.82 g/cm³ determined using drainage method.     

Characteristics of ZnO–B2O3–CaO–Na2O–P2O5 glass powders prepared by spray pyrolysis

Fine-sized ZnO–B₂O₃–CaO–Na₂O–P₂O₅ glass powders with spherical shape were directly prepared by high temperature spray pyrolysis. The ZnO–B₂O₃–CaO–Na₂O–P₂O₅ powders prepared by spray pyrolysis at temperatures above 1200 °C had broad peaks at around 30° in the XRD patterns. The glass transition temperatures (T_g) of the glass powders obtained by spray pyrolysis at preparation temperatures between 900 °C and 1400 °C were near 480 °C regardless of the preparation temperatures. The dielectric layers formed from the glass powders prepared by spray pyrolysis at preparation temperatures above 1300 °C had clean surface and dense inner structure at the firing temperature of 580 °C. The transmittance of the dielectric layer formed from the glass powders obtained by spray pyrolysis at preparation temperature of 1400 °C was 90% at the firing temperature of 580 °C, in which the thickness of the dielectric layer was 13 μm. The UV cutoff edges gradually shift towards longer wavelength with increasing the preparation temperature of glass powders and the firing temperature of dielectric layers.     

Characteristic crystal growth from amorphous WO3 film by vacuum heating

Selective growth of WO₂, W and WO_3−x crystals from amorphous WO₃ film by vacuum heating at 400–900°C was clarified. The grown WO_3−x crystals were incommensurate structure based on crystallographic share structure. The growth process of WO₂ crystal in the amorphous film was directly observed at high temperature in the electron microscope. The growth front of the WO₂ crystal consumes WO₃ microcrystallites with various orientations. The growth speed of the WO₂ depended on WO₃ microcrystallites orientation. The origin of the wavy growth front of WO₂ was due to an orientation dependence of the WO₃ microcrystallites.     

Growth of Na modified potassium lithium niobate crystal by the Czochralski method

Transparent Na modified potassium lithium niobate (Na_0.23K_2.60Li_1.82Nb_5.35O_15.70; NKLN) crystal was successively grown by the Czochralski method using RF induction heating from melt composition Na₂O:K₂O : Li₂O:Nb₂O₅=2:30:25:43 mol%. NKLN crystal showed a tetragonal tungsten bronze structure with lattice constants a=12.5446±0.0010 Å and c=4.0129±0.0005 Å at room temperature. The dielectric constant along the c-axis ε₃₃ showed a sharp maximum around 480 °C. Optical transmission edge was 370 nm and optical transmission spectra showed no absorption at wavelengths ranging from 380 to 800 nm. The structural and optical properties of NKLN were similar to those of the near stoichiometric KLN crystals. We believe that the growth of NKLN by the Czochralski method has an advantage for a large size and high-quality crystal.     

Glass formation in the PbBr2–PbCl2–PbF2–PbO–P2O5 system

New glasses in the PbBr₂–PbCl₂–PbF₂–PbO–P₂O₅ system have been prepared and characterized. The glass-forming regions have been explored and the stability of the glasses against crystallization studied. Results show that the PbBr₂–PbCl₂–P₂O₅ ternary system has a broad glass-forming region which extends to 30 mol% P₂O₅. Most of the glasses in this system show strong stability against crystallization and some have glass transition temperatures as low as 146°C. When 5% PbO or 5% PbF₂ is introduced into the PbBr₂–PbCl₂–P₂O₅ system, the glass-forming region becomes smaller and the glass transition temperatures increase. However, the introduction of 2.5% PbF₂ and 2.5% PbO into the ternary system increases the glass transition temperature and broadens the glass-forming region. The introduction of PbF₂ alone improves the glass-forming ability of the system while the introduction of PbO alone lowers the glass-forming ability.     

Ambient-condition growth of superconducting YBa2Cu4O8 single crystals using KOH flux

YBa₂Cu₄O₈ is a stoichiometric oxide superconductor of T_c80 K. Unlike YBa₂Cu₃O_7−δ, this compound is free from oxygen vacancy or twin formation and does not have any microscopic disorder in the crystal. Doping with Ca raises its T_c to 90 K. The compound is a promising superconductor for technological application. Up to now, single crystals have not been grown without using specialized apparatus with extremely high oxygen pressure up to 3000 bar and at over 1100 °C due to the limited range of reaction kinetics of the compound. This fact has delayed the progress in the study of its physical properties and potential applications. We present here a simple growth method using KOH as flux that acts effectively for obtaining high-quality single crystals in air/oxygen at the temperature as low as 550 °C. As-grown crystals can readily be separated from the flux and exhibit a perfect orthorhombic morphology with sizes up to 0.7×0.4×0.2 mm³. Our results are reproducible and suggest that the crystals can be grown using a conventional flux method under ambient condition.     

A study of the chemical reactions involved in Li–Ca–N system

The chemical reactions and phases involved in the potential flux system of Li–Ca–N for the growth of bulk GaN crystals have been investigated under varying conditions. It is found that no preferential nitrification of Li or Ca by N₂ in Li–Ca melts at 500 °C. Only the ternary compound LiCaN is identified in the Li–Ca–N system under the present experimental conditions. Static N₂ pressures are found to enhance the formation of LiCaN compared to an N₂ stream. LiCaN forms from two possible pathways: one is a modified metathesis chemical reaction represented by Li₃N+Ca→LiCaN+2Li, and the other is a combination chemical reaction represented by Li₃N+Ca₃N₂→3LiCaN. The formation of LiCaN by the metathesis reaction is thermodynamically favored over the other pathway. In addition, the formation of LiCaN might benefit from a slightly larger initial amount of Li₃N compared with Ca or Ca₃N₂.     

Growth and properties of Pb[(Zn1/3Nb2/3)0.91Ti0.09]O3 single crystals directly from melt

Pb[(Zn_1/3Nb_2/3)_0.91Ti_0.09]O₃ (PZNT91/9) single crystals were grown by a modified Bridgman method directly from melt using an allomeric Pb[(Mg_1/3Nb_2/3)_0.69Ti_0.31]O₃ (PMNT69/31) single crystal as a seed. X-ray diffraction (XRD) measurement confirmed that the as-grown PZNT91/9 single crystals are of pure perovskite structure. Electrical properties and thermal stabilization of PZNT91/9 crystals grown directly from melt exhibit different characters from those of PZNT91/9 crystals grown from flux, although segregation and the variation of chemical composition are not seriously confirmed by X-ray fluorescence analysis (XPS). The [0 0 1]-oriented PZNT91/9 crystals cut from the middle part of the as-grown crystal boules exhibit broad dielectric-response peaks at around 105 °C, accompanied by apparent frequency dispersion. The values of piezoelectric constant d₃₃, remnant polarization P_r, and induced strain are about 1800–2200 pC/N, 38.8 μC/cm², and 0.3%, respectively, indicating that the quality of PZNT crystals grown directly from melt can be comparable to those of PZNT91/9 single crystals grown from flux. However, further work deserves attention to improve the dielectric properties of PZNT crystals grown directly from melt. Such unusual characterizations of dielectric properties of PZNT crystals grown directly from melt are considered as correlating with defects, microinhomogeneities, and polar regions.     

Determination of Na2O activities in silicate melts by EMF measurements

An EMF cell using a Na-β″-alumina electrolyte has been designed for the quantification of the thermodynamic activity of Na₂O (aNa₂O) in a series of sodium-bearing silicate liquids at high temperature. Initial experiments have been performed using Na₂O–0.663WO₃ and Na₂O–0.555MoO₃ as reference liquids. Values of aNa₂O derived for Na₂O–2SiO₂ binary melt are found to be in excellent agreement with data from the literature, confirming the validity of the method. To extend use of this experimental set-up to higher temperature, the aNa₂O of industrial C-glass has been calibrated as a reference liquid at temperatures up to 1263 °C. The influence of additions of CaO, Al₂O₃ and B₂O₃ on the Na₂O activity of binary sodium-silicates has been quantified. For each glass composition, measured values of aNa₂O are a function of temperature, log(aNa₂O) varying as a function of inverse absolute temperature. Activation energies derived from these data are all generally similar with the exception of industrial E-glass, which is rich in Al and poor in Na. At constant temperature, additions of network forming Al₂O₃ and B₂O₃ to a Na₂O–SiO₂ binary melt yield a decrease of the activity of Na₂O, while addition of network modifying CaO results in an increase in (aNa₂O). These changes are qualitatively consistent with predictions based upon expected modifications of melt structure. However, measured values of log(aNa₂O) do not correlate perfectly with theoretical models of glass basicity, suggesting that either sodium activity is decoupled from melt basicity, or that current models are insufficient to calculate that parameter, in particular for the case of liquids poor in Na and rich in Al.     

Growth and spectroscopic properties of Er single doped and Er–Yb co-doped YAl3(BO3)4 crystals

Er³⁺-doped and Er³⁺–Yb³⁺ co-doped yttrium aluminum borate (YAB) single crystals have been grown by the top-seeded solution growth method using a new flux system, namely NaF–MoO₃–B₂O₃. The Er³⁺ concentrations were 1.3 mol% for both single doped and co-doped crystals and the Yb³⁺ concentration in the Er³⁺–Yb³⁺ co-doped crystal was 20.0 mol% in the raw materials. The distribution coefficients of Er³⁺ single doped and Er³⁺–Yb³⁺ co-doped crystals were measured. The polarized absorption and fluorescence spectra of Er³⁺–Yb³⁺ co-doped crystal were recorded and compared with those of Er³⁺ single doped crystal. The results demonstrate that Er³⁺–Yb³⁺ co-doped YAB crystal is a potential candidate for 1.55 μm laser materials.     

Aurivillius结构Bi2MoxW1-xO6铁电功能晶体的生长与性质表征

本文采用固相反应法探索了Aurivillius结构Bi₂Mo_xW_1-xO₆体系的合成条件以及能够形成固溶体的成分范围,探索了Bi₂Mo_xW_1-xO₆晶体的助熔剂法生长体系,并对晶体的结构、变温介电性质和电阻率进行了测定和分析。Bi₂Mo_xW_1-xO₆体系中Mo的占比x可以在0~1的范围内连续变化,采用固相反应法可以在500~870 ℃范围内的不同温度合成纯的Bi₂Mo_xW_1-xO₆铁电相。采用Li₂B₄O₇-Bi₂O₃(摩尔比2∶1)作为助熔剂生长得到了厘米级Bi₂WO₆单畴晶体,厚度不小于2 mm,最大尺寸则达到了约40 mm。在n(Bi₂O₃)∶n(MoO₃)∶n(WO₃)∶n(Li₂B₄O₇)=1∶1∶1∶1(摩尔比)体系中生长得到了厚度约1 mm的Bi₂Mo_0.15W_0.85O₆厘米量级单畴晶体,结构解析表明Bi₂Mo_0.15W_0.85O₆属于正交晶系,Aba2(No.41)空间群。变温介电性质测试表明,Bi₂Mo_0.15W_0.85O₆晶体的介电常数ε₃₃由Bi₂WO₆晶体的70提高到了102,介电弛豫现象发生的温度由Bi₂WO₆晶体的430 ℃降到了330 ℃附近。变温电阻率测试表明,Bi₂WO₆与Bi₂Mo_0.15W_0.85O₆晶体的电阻率均随温度升高而降低,在100 ℃以下,Bi₂WO₆的电阻率高于Bi₂Mo_0.15W_0.85O₆晶体,且随温度升高,二者电阻率的差距在逐渐缩小。     

Bi20TiO32 nanocones prepared from Bi–Ti–O mixture by metalorganic decomposition method

Bi₂₀TiO₃₂ in the form of nanocones are reported for the first time, which have been found during the formation of Bi₂Ti₂O₇ nanocrystals. Bi₂₀TiO₃₂ nanocones were prepared by metalorganic decomposition technique. From X-ray patterns, it was found that Bi₂₀TiO₃₂ is a metastable phase, and can transform gradually into Bi₂Ti₂O₇ phase with the annealing time increasing at a temperature of 550°C. The image of field emission scanning electron microscopy shows that the lengths of the nanocones are up to several micrometers and the diameters of cusps range from 20 to 200 nm. The studies of transmission electron microscopy show that the nanocones are crystalline Bi₂₀TiO₃₂. The growth mechanism of Bi₂₀TiO₃₂ nanocones has been proposed, which is similar to the vapor–liquid–solid growth mechanism.     

Growth, dielectric, ferroelectric and optical properties of Ca0.28Ba0.72Nb2O6 single crystals

Calcium barium niobate Ca_0.28Ba_0.72Nb₂O₆ (CBN-28) crystals were grown by the Czochralski method. The effective segregation coefficients of Ca, Ba, Na elements in CBN-28 crystal growth were measured, and the rocking curve from 0 0 2 reflection of CBN-28 wafer was also measured by the high-resolution X-ray diffractometer D5005, and the full-width at half-maximum value was measured to be 70.6″. The measured dependence of dielectric constants on temperature showed the Curie temperature of the CBN-28 crystals is between 246.8 and 260 °C. Typical polarization–electric field (P–E) hysteresis loops were measured at room temperature. Ferroelectric 180° domains were observed by scanning electron microscopy (SEM) on the etched (0 0 1) surface of the CBN-28 crystals. The transmittance of [0 0 1]-oriented CBN-28 crystals was measured and the result shows that optical properties of CBN-28 crystal are almost the same as those of SBN for wavelengths between 2500 and 7500 nm.     

Densities of Li2O–B2O3 melts

The densities have been systematically measured in xLi₂O–(1−x)B₂O₃ melts of different compositions with Li₂O content varying from x=0 to 0.68 from their respective melting points up to about 1450 K with a modified Archimedean method. The density decreased with increasing temperature for all the melts measured in this work. When x<0.15, the plot of temperature versus density could be well fitted by a quadratic polynomial function, and when x0.15, density decreased linearly with increasing temperature. At a fixed temperature, the density of the melts increased rapidly with Li₂O content, went through a maximum at about x=0.333 (Li₂O–2B₂O₃), and then decreased slowly as Li₂O content was further increased. In addition, the volume expansion coefficient (β) was calculated based on the densities measured in this work, and it was found that a maximum value appeared in the dependence of β on the molar ratio of Li₂O at about x=0.333.     

Crystallization behavior and hydrophilic performances of V2O5–TiO2 films prepared by sol–gel dip-coating

Homogeneous and transparent V₂O₅–TiO₂ composite nanometer thin films were prepared on glass substrates by sol–gel processing and dip-coating technique. The films as well as the dried powder of bulk gel were characterized by different techniques like X-ray diffraction (XRD), high-resolution scanning electron microscopy (HRSEM), atomic force microscope (AFM) and thermogravimetry–differential thermal analysis (TG–DTA). The hydrophilicity of the films was determined by measuring the water contact angles on the films. The results showed that the dopant of V₂O₅ on TiO₂ thin films could produce a visible-light response to the films, and the introduction of V₂O₅ could suppress the structural phase transition and crystal growth of TiO₂ crystal. Finally, the relationship between crystalline size and hydrophilicity under sunlight was investigated in this article.     

The effect of MgO on the thermodynamics of the Fe/Fe-redox equilibrium and the incorporation of iron in soda-magnesia-aluminosilicate melts

Melts with the basic compositions 10Na₂O · 10MgO · xAl₂O₃ · (80−x)SiO₂ (x=0, 5, 10, 15 and 20), 10Na₂O · xMgO · 10Al₂O₃ · (80−x)SiO₂ (x=5, 10, 15 and 20) and xNa₂O · 10MgO · 10Al₂O₃ · (80−x)SiO₂ (x=5, 10 and 15) all doped with 0.25 mol% Fe₂O₃ were studied using square-wave voltammetry. The temperatures applied were in the range of 1000–1600 °C. The square-wave voltammograms recorded show peaks caused by the reduction of Fe³⁺ to Fe²⁺. The attributed peak potentials measured decreased linearly with decreasing temperatures. Increasing the MgO-concentration led to more negative peak potentials. Introducing alumina in the melt first resulted in less negative peak potentials. If the molar Al₂O₃-concentration is equal to that of Na₂O (=10 mol%) the peak potentials are least negative. Further increase of the Al₂O₃-concentration led to more negative peak potentials. The variation of the Na₂O-concentration led to a maximum in the peak potentials at an Na₂O-concentration of 10 mol%. An empirical formula which allows the calculation of standard potentials from the chemical composition is proposed. Furthermore, a structural explanation for the effect of the chemical composition is given. Especially, the incorporation of Al₂O₃ as AlO₄⁻-tetrahedra at [Al₂O₃] < [Na₂O] and as network modifier at larger concentrations was structurally explained by the similarities of Fe²⁺ and Mg²⁺, with respect to cation radii and metal–oxygen bond lengths.     

Phase relations around langasite (La3Ga5SiO14) in the system La2O3–Ga2O3–SiO2 in air

Phase relations around langasite (LGS, La₃Ga₅SiO₁₄) were studied on the basis of phase assemblage observed during calcination and crystallization process of samples of various compositions in the ternary system La₂O₃–Ga₂O₃–SiO₂. A ternary compound of apatite structure, La₁₄Ga_xSi_9–xO_39–x/2 was found for the first time. Crystallization of this compound was observed in the cooling process of molten samples of stoichiometric LGS as well as LGS single crystal, demonstrating that LGS is an incongruent-melting compound. A phase diagram was established primarily based on the crystallization sequence in the cooling process.     

Growth of NaBi(WO4)2 crystal by modified-Bridgman method

NaBi(WO₄)₂ (NBW) crystals have been grown for the first time by modified-Bridgman method. Influences of some factors on the crystal growth process are discussed. X-ray powder diffraction experiments show that the unit cell parameters of NBW crystal are a=b=0.5284 nm, c=1.1517 nm, and V=0.3215 nm³. The differential thermal analysis shows that the NBW crystal melts at 923°C.