Electrical conduction and magnetoelectric effect of (x) BaTiO3 + (1−x) Ni0.92Co0.03Cu0.05Fe2O4 composites in ferroelectric rich region

Particulate composites with composition (x)BaTiO₃+(1−x)Ni_0.92Co_0.03Cu_0.05Fe₂O₄ in which x varies as 1, 0.85, 0.70, 0.55 and 0 (in mol%) were prepared by the conventional double sintering ceramic technique. The presence of two phases viz. ferromagnetic (Ni_0.92Co_0.03Cu_0.05Fe₂O₄) and ferroelectric (BaTiO₃) was confirmed by X-ray diffraction analysis. The dc resistivity and thermo-emf measurements were carried out with variation of temperature. The ac conductivity (σ_ac) measurements investigated in the frequency range 100 Hz to 1 MHz conclude that the conduction in these composites is due to small polarons. The variation of dielectric constant and loss tangent with frequency (20 Hz to 1 MHz) was studied. The static magnetoelectric conversion factor, i.e. dc (dE/dH)_H was measured as a function of intensity of applied magnetic field. The changes were observed in electrical properties as well as in magnetoelectric voltage coefficient as the molar ratio of the constituent phases was varied. A maximum value of magnetoelectric conversion factor of 536.06 μV/cm Oe was observed for the composite with 70% BaTiO₃+30% Ni_0.92Co_0.03Cu_0.05Fe₂O₄ at a dc magnetic field of 2.3 K Oe. The maximum magnetoelectric conversion output has been explained in terms of ferrite-ferroelectric content, applied static magnetic field and resistivity.     

DC conductivity and magnetic properties of piezoelectric–piezomagnetic composite system

A series of composites (1−x) (Ni_0.8Zn_0.2Fe₂O₄)+x (BaTiO₃), where x=0%, 20%, 40%, 60%, 80% and 100% BT content, have been prepared by the standard ceramic technique, then sintered at 1200 °C for 8 h. X-ray diffraction analysis shows that the prepared composites consist of two phases, ferrimagnetic and ferroelectric. DC electrical resistivity, thermoelectric power, charge carriers concentration and charge carrier mobility have been studied at different temperatures. It was found that the DC electrical conductivity increases with increasing BT content. The values of the thermoelectric power were positive and negative for the composites indicating that there are two conduction mechanisms, hopping and band conduction, respectively. Using the values of DC electrical conductivity and thermoelectric power, the values of charge carrier mobility and the charge carrier concentration were calculated. Magnetic measurements (hysteresis loop and magnetic permeability) show that the magnetization decreases by increasing BT content. M–H loop of pure Ni_0.6 Zn_0.4 Fe₂O₄ composite indicates that it is paramagnetic at room temperature and that the magnetization is diluted by increasing the BT content in the composite system. The value of magnetoelectric coefficient for the composites decreases by increasing BT content for all the compositions except for 40% BT content, which may be due to the low resistivity of magnetic phase compared with the BT phase that causes a leakage of induced charges on the piezoelectric phase. Since both ferroelectric and magnetic phases preserve their basic properties in the bulk composite, the present BT–NZF composite are potential candidates for applications as pollution sensors and electromagnetic waves.     

Magnetoelectric properties of particulate and bi-layer PMN-PT/CoFe2O4 composites

Our studies comprise electrical dielectric and magnetoelectric properties of CoFe₂O₄ (CFO) and Pb(Mg_1/3Nb_2/3)_0.67Ti_0.33O₃ [PMN-PT] magnetoelectric composites. The individual phases were prepared by conventional ceramic method. The particulate composites of ferrite and ferroelectric phases were prepared in ferroelectric rich region. Presence of both the phases in the composites was confirmed using X-ray diffraction techniques. The scanning electron microscopic images recorded in backscattered mode were used to study the microstructure of composites. Lattice constant, dielectric constant, electrical resistivity, ferroelectric, and magnetic properties of individual as well as particulate composites were studied. Further the bi-layer composites were made using the discs obtained from the powders of individual phases where hot press technique was employed to obtain disc of individual phases. CFO phase used in bi-layer composites was obtained using chemical co-precipitation technique. Magnetoelectric (ME) measurements were carried out on both, particulate and layered magnetoelectric composites. Comparison of ME signal obtained from particulate and layered composites revealed that the layered composites gives superior magnetoelectric signal. ME data obtained for layered composites show good agreement with the theoretical model.     

Magnetic and dielectric properties of Ni0.8Co0.1Cu0.1Fe2O4+PZT composites

Magnetoelectric composites of Ni_0.8Co_0.1Cu_0.1Fe₂O₄ and Lead Zirconate Titanate (PZT) were prepared by using conventional ceramic method. The measured values of saturation magnetization (M_s) and magnetic moments (μ_B) are in accordance with the volume fraction of ferrite content in the composite. The dielectric constant of the composites decreases with frequency. The plots of dielectric constant () against temperature (T) show a peak at their respective transition temperatures. The ME output was measured by varying dc bias magnetic field. A large ME output signal of 776 mV/cm was observed for 35% ferrite +65% ferroelectric composite. The magnetoelectric (ME) response is found to be dependent on the content of ferrite phase.     

Magnetic, ferroelectric, elastic, and inelastic properties of xNi0.4Zn0.6Fe2O4-(1 ? x)Pb0.95Sr0.05Zr0.53Ti0.47O3 composites

The magnetoelectric composites xNi_0.4Zn_0.6Fe₂O₄-(1 − x)Pb_0.95Sr_0.05Zr_0.53Ti_0.47O₃ (x = 0, 0.2, 0.4, 0.6, 0.8, 1.0) were prepared by ceramic technology. It is established that these composites have a two-phase structure. The magnetic and ferroelectric properties of the composites were studied by measuring the hysteresis loops and the temperature dependences of corresponding quantities on the composite composition. It is revealed that the phase content in the composite strongly affects the properties studied. Original Russian Text ? S.A. Gridnev, A.G. Gorshkov, O.N. Korolevskaya, 2009, published in Fizika Tverdogo Tela, 2009, Vol. 51, No. 8, pp. 1464–1467.     

Studies on lead-free multiferroic magnetoelectric composites

Lead-free multiferroic magnetoelectric composites consisting of ferrimagnetic Ni_0.93Co_0.02Mn_0.05Fe_1.95O₄ (NMF) and ferroelectric Na_0.5Bi_0.5TiO₃ (NBT) phases were synthesized by the solid-state sintering method. The presence of constituent phases in composites was confirmed by X-ray diffraction (XRD) and scanning electron microscopy (SEM). A systematic study of dc conductivity as a function of temperature (RT −450 °C) revealed that the conduction is due to small polarons. The effect of constituent phase variation on the dielectric constant and piezoelectric strength (d₃₃) was examined. The composites exhibited typical magnetic hysteresis (M–H) loops at room temperature. Furthermore, magnetoelectric (ME) output was evaluated as a function of applied magnetic field, which is a product property of the constituent phases. The compound 50% NMF–50%NBT is a new lead-free magnetoelectric composite with 155 μV/cm ME output, which may have potential applications.     

Magnetic,magnetoelectric and dielectric behavior of CoFe2O4–Pb(Fe1/2Nb1/2)O3 particulate and layered composites

Magnetic, magnetoelectric and dielectric properties of multiferroic CoFe₂O₄–Pb(Fe_1/2Nb_1/2)O₃ composites prepared as bulk ceramics were compared with those of tape cast and cofired laminates consisting of alternate ferrite and relaxor layers. X-ray diffraction analysis and Scanning Electron Microscope observations of ceramic samples revealed two-phase composition and fine grained microstructure with uniformly distributed ferrite and relaxor phases. High and broad maxima of dielectric permittivity attributed to dielectric relaxation were found for ceramic samples measured in a temperature range from −55 to 500 °C at frequencies 10 Hz–2 MHz. Magnetic hysteresis, zero-field cooled (ZFC) and field cooled (FC) curves, and dependencies of magnetization on temperature for both magnetoelectric composites were measured with a vibrating sample magnetometer in an applied magnetic field up to 80 kOe at 4–400 K. The hysteresis loops obtained for composites are typical of a mixture of the hard magnetic material with a significant amount of the paramagnet. The bifurcation of ZFC–FC magnetizations observed for both composites implies spin-glass behavior. Magnetoelectric properties at room temperature were investigated as a function of dc magnetic field (0.3–7.2 kOe) and frequency (10 Hz–10 kHz) of ac magnetic field. Both types of composites exhibit a distinct magnetoelectric effect. Maximum values of magnetoelectric coefficient attained for the layered composites exceed 200 mV/(cm Oe) and are almost three times higher than those for particulate composites.     

Structure,Ferroelectric, and Magnetoelectric Properties of Bulk PZT–NiFe<Subscript>1.9</Subscript>Co<Subscript>0.02</Subscript>О<Subscript>4 – δ</Subscript> Composites

The phase composition, microstructure, and dielectric, ferroelectric, magnetic, and magnetoelectric properties of bulk ceramic (1 – x)PZT–xNiFe_1.9Co_0.02О_{4 – δ} composites with 3–0 connectivity have been studied. Using X-ray diffraction and electron microscopy, it has been established that the ferrimagnetic (spinel- like) and ferroelectric (tetragonal perovskite-like) phases separately exist in the composites of all compositions. The simultaneous existence of ferroelectric and ferrimagnetic properties in the composites is confirmed by measuring their P(E) and σ(B) hysteresis loops and studying the temperature dependences of dielectric and magnetic properties. The synthesized composites have high magnetoelectric characteristics: their voltage coefficient at x = 0.4 is 215 mV/A at a frequency of 1 kHz and 130 V/A at an electromechanical resonance frequency of 380 kHz.     

Piezoelectric, dielectric and magnetic properties of (1-x)Pb[Zr, Ti, (Mg1/2W1/2), (Ni1/3Nb2/3)]O3+x(Ni, Co, Cu)FeO4 composites

The phase structure, microstructure, piezoelectric properties, dielectric characteristic and the ME effect of magnetoelectric Pb[Zr_0.23Ti_0.36+0.02(Mg_1/2W_1/2)+0.39(Ni_1/3Nb_2/3)]O₃ (PZT)+xNi_0.8Co_0.1Cu_0.1Fe₂O₄ (NCCF) composite ceramics were prepared by the conventional solid state reaction method. The structural analysis of both the constituent phases and their composites was carried out by X-ray diffraction, energy dispersive spectrometry and scanning electron microscopy. The results showed cubic spinel structure for ferrite phase and tetragonal perovskite structure for ferroelectric phase. The piezoelectric constant, dielectric constant, Curie temperature, remanent polarization and coercive electric field decreased with increase of ferrite content. The coercive field strength, saturation magnetization and remanent magnetization increased with increasing ferrite content.     

Dielectric and magnetoelectric properties of BaTiO3–CoMn0.2Fe1.8O4 particulate (0-3) multiferroic composites

Multiferroic properties of (x) CoMn_0.2Fe_1.8O₄–(1-x) BaTiO₃ particulate magnetoelectric (ME) composites with x = 0.1, 0.2, 0.3 M percentage was investigated. The CoMn_0.2Fe_1.8O₄ (CMFO) phase was synthesized by solution combustion route and BaTiO₃ (BT) phase was synthesized by wet chemical method. X-ray diffraction studies revealed the purity of constitute phases; confirmed the manifestation of CMFO and BT within the ME composite structure. The microstructural aspects were observed by using Fe-SEM; revealed the effect of constituent phases on the average grain size of the composites. The temperature dependent dielectric properties for BT exhibited the three anomalies associated to its crystallographic lattice structure change with temperature. Dielectric constant of the composite was found to be decreased with CMFO content. All the composite structures exhibited typical magnetic hysteresis nature at room temperature and showed linear effect on the saturation magnetization of the composite with CMFO content. The ME response was examined at room temperature with an ac magnetic field at 1 kHz, all the composite showed a sharp decreasing behavior of the ME voltage coefficient (α_ME) to an applied dc bias in low field region. The maximum α_ME factor of ～8.51 mV/cm Oe was observed for 10% CMFO–90% BT composition.     

Microstructure-property relationship in magnetoelectric bulk composites

We present systematic studies that comprise phase connectivity and dielectric, multiferroic (MF) and magnetoelectric (ME) properties of (x) Ni_0.8Co_0.2Fe₂O₄+(1−x) Pb(Mg_1/3Nb_2/3)_0.67Ti_0.33O₃ [where x=0.15, 0.30 and 0.45] ME composites prepared by conventional solid-state reaction method. Scanning electron microscopic images of the composites predict different types of connectivity schemes viz 3-0, 3-1 and 3-3. The phase transition temperature of PMN-PT is independent of Ni_0.8Co_0.2Fe₂O₄ content. Room temperature P-E and M-H loops indicate the simultaneous existence of ferroelectric/magnetic ordering. In order to study the possibility of monitoring electrical ordering by means of a magnetic field, ME measurements were carried out. The composition-dependent phase connectivity was well co-related to formation of percolation path and inturn magnetoelectric output.     

Phase transitions in xPbZr0.53Ti0.47O3-(1 − x)Mn0.4Zn0.6Fe2O4 magnetoelectric composites

The elastic, inelastic, and dielectric properties of the magnetoelectric composite xPbZr_0.53Ti_0.47O₃-(1 ? x)Mn_0.4Zn_0.6Fe₂O₄ (PZT-MZF) are studied in the temperature range from room temperature to 673 K. The influence of the ferroelectric PZT phase on the magnetic phase transition and the magnetic MZF phase on the ferroelectric phase transition is revealed. It is established that, as the PZT content increases, the degree of diffuseness of the phase transition decreases and a gradual crossover from a pronounced relaxor behavior to a more ordered ferroelectric behavior occurs.     

Magnetoelectric characterization of xNi0.75Co0.25Fe2O4-(1−x)BiFeO3 nanocomposites

Magnetoelectric (ME) nanocomposites containing Ni_0.75Co_0.25Fe₂O₄-BiFeO₃ phases were prepared by citrate sol-gel process. X-ray diffraction (XRD) analysis showed phase formation of xNi_0.75Co_0.25Fe₂O₄-(1−x)BiFeO₃ (x=0.1, 0.2, 0.3 and 0.4) composites on heating at 700 °C. Transmission electron microscopy revealed the formation of powders of nano order size and the crystal size was found to vary from 30 to 85 nm. Dispersion in dielectric constant (ε) and dielectric loss (tan δ) in the low-frequency range have been observed. It is seen that nanocomposites exhibit strong magnetic properties and a large ME effect. On increasing Ni_0.75Co_0.25Fe₂O₄ contents in the nanocomposites, the saturation magnetization (M_S) and coercivity (H_C) increased after annealing at 700 °C. The large ME output in the nanocomposites exhibits strong dependence on magnetic bias and magnetic field frequency. The large value of ME output can be attributed to small grain size of ferrite phase of nanocomposite being prepared by citrate precursor process.     

Multiferroic and magnetoelectric properties of MnFe2O4/(Pb0.8Sr0.2)TiO3 composite films

Abstract

MnFe₂O₄/(Pb_0.8Sr_0.2)TiO₃ (MFO/PST20) heterostructured composite films with three different structures have been grown on Pt/TiO₂/SiO₂/Si substrates by metal–organic decomposition processing via spin coating technique. The structural analysis revealed that the crystal axes of the MnFe₂O₄ are aligned with those of the PST20 ferroelectric matrix with obvious interfaces and no diffusions exist in all the three composite films. These composite films exhibit simultaneously multiferroic and magnetoelectric responses at room temperature. The growth structure of MFO and PST20 layers has an effect on multiferroic and magnetoelectric coupling behaviours of the composite films. The bi- and four-layered MFO/PST20 composite films exhibit superior ferroelectric properties compared to the tri-layered film. The increasing MFO and PST20 layers in the composite films enhance ferromagnetic properties and are closely related to the strain release in MnFe₂O₄ phase. The MFO/PST20 bi-layered composite film shows a high magnetoelectric voltage co-efficient α_E ~ 194 mVcm^?1Oe^?1 at a dc magnetic field H_dc ~ 2.5 kOe. A significant decrease in α_E value has been observed for tri- and four- layered composite films. A close correlation between phase selective residual stress and magnetoelectric properties has been emerged. The results are reasonably encouraging for employing MnFe₂O₄ for growing multiferroic–magnetoelectric composite films.     

Study of magnetic properties and magnetoelectric effect in (x) Ni0.5Zn0.5Fe2O4+(1−x)PZT composites

Magnetoelectric (ME) composites consisting of ferrite phase (x) Ni_0.5Zn_0.5Fe₂O₄+ferroelectric phase (1−x)Pb Zr_0.8Ti_0.2O₃ (Lead Zirconate Titanate—PZT) in which x (mol%) varies between 0 and 1 (0.0≤x≤1.0) was synthesized by double sintering ceramic method. The presence of constituent phases of ferrite, ferroelectric and their composites was confirmed by X-ray diffraction studies. The hysteresis measurement was used to study magnetic properties such as saturation magnetization (M_S) and magnetic moment (μ_B). The existence of single domain (SD) particle in the ferrite phase and mixed (SD+MD) particle in the composites was studied from AC susceptibility measurements. ME voltage coefficient for each mol% of ferrite phase was measured as a function of applied DC magnetic field and at the same time influence of magnetic field on ME response and resistivity of composites was studied. The maximum ME voltage coefficient of 0.84 mV/cm Oe was observed for 15% of ferrite phase and 85% of ferroelectric phase in the composites.     

Phase transition, structural and electrical properties of Pb(Zn1/3Nb2/3)O3-doped Pb(Ni1/3Nb2/3)O3-PbTiO3 ceramics prepared by solid-state reaction method

Phase pure perovskite (1−x−y)Pb(Ni_1/3Nb_2/3)O₃-xPb(Zn_1/3Nb_2/3)O₃-yPbTiO₃ (PNN-PZN-PT) ferroelectric ceramics were prepared by conventional solid-state reaction method via a B-site oxide mixing route. The PNN-PZN-PT ceramics sintered at the optimized condition of 1185 °C for 2 h exhibit high relative density and rather homogenous microstructure. With the increase of PbTiO₃ (PT) content, crystal structure and electrical properties of the synthesized PNN-PZN-PT ceramics exhibit successive phase transformation. A morphotropic phase boundary (MPB) is supposed to form in (0.9−x)PNN-0.1PZN-xPT at a region of x=32-36 mol% confirmed by X-ray diffraction (XRD) measurement and dielectric measurement. The MPB composition can be pictured as providing a “bridge” connecting rhombohedral ferroelectric (FE) phase and tetragonal one since crystal structure of the MPB composition is similar to both the rhombohedral and tetragonal lattices. Dielectric response of the sintered PNN-PZN-PT ceramics also exhibits successive phase-transition character. 0.64PNN-0.1PZN-0.26PT exhibits broad, diffused and frequency dependent dielectric peaks indicating a character of diffused FE-paraelectric (PE) phase transition of relaxor ferroelectrics and 0.40PNN-0.1PZN-0.50PT exhibits narrow, sharp and frequency independent dielectric peaks indicating a character of first-order FE-PE phase transition of normal ferroelectrics. The FE-PE phase transition of 0.56PNN-0.1PZN-0.34PT is nearly first-order with some diffused character, which also exhibits the largest value of piezoelectric constant d₃₃ of 462pC/N.     

Enhanced mangnetoelectric voltage in multiferroic particulate Ni0.83Co0.15Cu0.02Fe1.9O4−δ/PbZr0.52Ti0.48O3 composites – dielectric,piezoelectric and magnetic properties

Multiferroic particulate composites of Ni_0.83Co_0.15Cu_0.02Fe_1.9O_4−δ– NCCF and lead zirconate titanate (PZT) were prepared conventional ceramic method. The generic formulae x NCCF + (1−x) PZT where x = 0.1, 0.2, 0.3, 0.4, 0.5 and 0.6 mole fractions. The presence of two phases in multiferroic was confirmed with XRD technique. The dielectric constant and loss tangent were studied as a function of frequency (100 Hz to 1 M Hz) and temperature (30–500 °C). The piezoelectric coefficient d₃₃ were also studied on these particulate composites. The hysteresis behaviour was studied to understand the magnetic properties such as saturation magnetization (Ms) and magnetic moment (μ_B). The static magnetoelectric (ME) voltage coefficient was measured as a function of dc magnetic bias field. A high value of ME output (3151 mV/Oe.cm) was obtained in the composite containing 50% highly magnetostrictive ferrite component NCCF – 50% highly piezoelectric ferroelectric component PZT. These multiferroic particulate composites are used as phase shifters, magnetic sensors, cables etc.     

Magnetic properties of xNi0.53Cu0.12Zn0.35Fe1.88O4+(1−x)BaTiO3 nanocomposites

The nanocrystalline Ni_0.53Cu_0.12Zn_0.35Fe_1.88O₄ and BaTiO₃ powders were prepared using Microwave-Hydrothermal (M-H) method at 160 °C/45 min. The as synthesized powders were characterized using the X-ray diffraction (XRD) and Transmission Electron Microscope (TEM). The size of the powders that were synthesized using M-H system was found to be ∼30 and ∼50 nm for ferrite phase and ferroelectric phases, respectively. The powders were densified using microwave sintering method at 900 °C/30 min. The ferrite and ferroelectric phases were observed from XRD and morphology of the composites was observed with the Scanning Electron Microscope (SEM).The magnetic hysteresis loops were recorded using the Vibrating Sample Magnetometer (VSM).The frequency dependence of real (μ′) and imaginary (μ″) parts of permeability was measured in the range of 1 MHz-1.8 GHz. The permeability decreases with an increase of BaTiO₃ content at 1 MHz. The transition temperature (T_C) of ferrite was found to be 245 °C. The T_C of composite materials decreases with an increase in BaTiO₃ content.     

Effect of Cr substitution on the multiferroic properties of BiFe1 − xCrxO3 compounds

Single-phase BiFe_1 − xCr_xO₃ (x=0, 0.05 and 0.1) compounds are synthesized by a sol-gel process. The lattice parameters decrease and the magnetizations increase with the Cr content. Moreover, the magnetoelectric coupling between magnetic order and ferroelectric order at room temperature was enhanced.     

Fe掺杂量对双层复合结构BaTi1-zFezO3+δ-Tb1-xDyxFe2-y中磁电耦合的影响

采用溶胶凝胶方法制备了Fe掺杂钛酸钡多晶系列陶瓷BaTi_1-zFe_zO_3+δ(0.005≤z≤0.02) (BTFO).X射线衍射实验显示,所制备的BTFO的结构仍然为四方相钙钛矿.差热分析表明,该BTFO样品的铁电-顺电转变温度及相变潜热随掺杂量z的增加而下降.将该BTFO极化后与Tb_1-xDy_xF 关键词： 磁电耦合 掺杂效应 掺杂钛酸钡