Ni/Al2O3 catalysts for CO methanation: Effect of Al2O3 supports calcined at different temperatures

The correlation between phase structures and surface acidity of Al2O3 supports calcined at different temperatures and the catalytic performance of Ni/Al2O3 catalysts in the production of synthetic natural gas(SNG) via CO methanation was systematically investigated. A series of 10 wt% NiO/Al2O3 catalysts were prepared by the conventional impregnation method, and the phase structures and surface acidity of Al2O3 supports were adjusted by calcining the commercial γ-Al2O3 at different temperatures(600–1200 C). CO methanation reaction was carried out in the temperature range of 300–600 C at different weight hourly space velocities(WHSV = 30000 and 120000 mL·g-1h-1) and pressures(0.1 and 3.0 MPa). It was found that high calcination temperature not only led to the growth in Ni particle size, but also weakened the interaction between Ni nanoparticles and Al2O3 supports due to the rapid decrease of the specific surface area and acidity of Al2O3 supports. Interestingly, Ni catalysts supported on Al2O3 calcined at 1200 C(Ni/Al2O3-1200) exhibited the best catalytic activity for CO methanation under different reaction conditions. Lifetime reaction tests also indicated that Ni/Al2O3-1200 was the most active and stable catalyst compared with the other three catalysts, whose supports were calcined at lower temperatures(600, 800 and 1000 C). These findings would therefore be helpful to develop Ni/Al2O3 methanation catalyst for SNG production.     

Removal of carbonyl sulfide from CO2 stream using AgNO3-modified NaZSM-5

Removal of carbonyl sulfide(COS) from CO2 stream is significant for the production and utilization of food grade CO2. This study investigates the adsorption performance of Ag/NaZSM-5 as adsorbent prepared by incipient wetness impregnation for the removal of COS from a CO2 stream in a fixed-bed adsorption apparatus. Effects of various conditions on the preparation of adsorbent, adsorption and desorption were intensively examined. The results revealed that COS can be removed to below 1×10-9from a CO2stream(1000 ppm COS/CO2) using Ag/NaZSM-5(10 wt% AgNO3) with an adsorption capacity of 12.86 mg·g-1. The adsorbent can be fully regenerated using hot air at 450 C. The adsorption ability remained stable even after eight cycles of regeneration.     

Kinetic study of propane dehydrogenation and catalyst deactivation over Pt-Sn/Al2O3 catalyst

The kinetics of propane dehydrogenation and catalyst deactivation over Pt-Sn/Al2O3 catalyst were studied.Performance test runs were carried out in a fixed-bed integral reactor.Using a power-law rate expression for the surface reaction kinetics and independent law for deactivation kinetics,the experimental data were analyzed both by integral and a novel differential method of analysis and the results were compared.To avoid fluctuation of time-derivatives of conversion required for differential analysis,the conversion-time data were first fitted with appropriate functions.While the time-zero and rate constant of reaction were largely insensitive to the function employed,the rate constant of deactivation was much more sensitive to the function form.The advantage of the proposed differential method,however,is that the integration of the rate expression is not necessary which otherwise could be complicated or impossible.It was also found that the reaction is not limited by external and internal mass transfer limitations,implying that the employed kinetics could be considered as intrinsic ones.     

Comparative study of fluidized-bed and fixed-bed reactor for syngas methanation over Ni-W/TiO₂-SiO₂catalyst

In this work,syngas methanation over Ni-W/TiO2-SiO2catalyst was studied in a fluidized-bed reactor(FBR)and its performance was compared with a fixed-bed reactor(FIXBR).The effects of main operating variables including feedstock gases space velocity,coke content,bed temperature and sulfur-tolerant stability of 100 h life were investigated.The structure of the catalysts was characterized by XRD,N2adsorptiondesorption and TEM.It is found that under same space velocity from 5000 h 1to 25000 h 1FBR gave a higher CH4yield,lower coke content,and lower bed temperature than those obtained in FIXBR.Ni-W/TiO2-SiO2catalyst possessed excellent sulfur-tolerant stability on the feedstock gases less than 500 ppm H2S in FBR.The carbon deposits formed on the spent catalyst were in the form of carbon fibers in FBR,while in the form of dense accumulation distribution appearance in FIXBR.     

Effect of Sr loading on oxydehydrogenation of propane to propylene over Al₂O₃-supported V-Mo catalysts

Incorporation of strontium into V-Mo alumina-supported catalyst enhanced its performance (increased conversion and selectivity,decreased reducibility and improved stability) in propane oxydehydrogenation to propylene.12.5% Sr loading was shown to be the optimum content to the V-Mo catalyst.The results were supported by various characterization techniques,namely,BET,XRD,SEM,FTIR and TPD.     

Investigation of CO and formaldehyde oxidation over mesoporous Ag/Co3O4 catalysts

CO and formaldehyde(HCHO)oxidation reactions were investigated over mesoporous Ag/Co3O4 catalysts prepared by one-pot(OP)and impregnation(IM)methods.It was found that the one-pot method was superior to the impregnation method for synthesizing Ag/Co3O4 catalysts with high activity for both reactions.It was also found that the catalytic behavior of mesoporous Co3O4 and Ag/Co3O4 catalysts for the both reactions was different.And the addition of silver on mesoporous Co3O4 did not always enhance the catalytic activity of final catalyst for CO oxidation at room temperature(20 C),but could significantly improve the catalytic activity of final catalyst for HCHO oxidation at low temperature(90 C).The high surface area,uniform pore structure and the pretty good dispersion degree of the silver particle should be responsible for the excellent low-temperature CO oxidation activity.However,for HCHO oxidation,the addition of silver played an important role in the activity enhancement.And the silver particle size and the reducibility of Co3O4 should be indispensable for the high activity of HCHO oxidation at low temperature.     

Improvement in the Water Retention Characteristics of Sandy Loam Soil Using a Newly Synthesized Poly(acrylamide-<em>co</em>-acrylic Acid)/AlZnFe₂O₄ Superabsorbent Hydrogel Nanocomposite Material

The use of some novel and efficient crop nutrient-based superabsorbent hydrogel nanocomposites (SHNCs), is currently becoming increasingly important to improve the crop yield and productivity, due to their water retention properties. In the present study a poly(Acrylamide-co-acrylic acid)/AlZnFe₂O₄ superabsorbent hydrogel nanocomposite was synthesized and its physical properties characterized using Energy Dispersive X-ray (EDX), FE-SEM and FTIR spectroscopic techniques. The effects of different levels of SHNC were studied to evaluate the moisture retention properties of sandy loam soil (sand 59%, silt 21%, clay 19%, pH 7.4, EC 1.92 dS/m). The soil amendment with 0.1, 0.2, 0.3 and 0.4 w/w% of SHNC enhanced the moisture retention significantly at field capacity compared to the untreated soil. Besides, in a separate experiment, seed germination and seedling growth of wheat was found to be notably improved with the application of SHNC. A delay in wilting of seedlings by 5-8 days was observed for SHNC-amended soil, thereby improving wheat plant growth and establishment.     

Nano Si preparation by constant cell voltage electrolysis of FFC-Cambridge Process in molten CaCl₂

Using FFC-Cambridge Process to prepare Si from SiO2 is a promising method to prepare nanostructured and highly pure silicon for solar cells.However,the method still has many problems unsolved and the controlling effect of the cell voltage on silicon product is not clear.Here we report in this article that nano cluster-like silicon product with purity of 99.95%has been prepared by complete conversion of raw material SiO2,quartz glass plate,using constant cell voltage electrolysis FFC-Cambridge Process.By analysis of XRD,EDS,TEM,HRTEM and ICP-AES as well as the discussion from the thermodynamics calculation,the morphology and components of the product based on the change of cell voltage are clarified.It is clear that pure silicon could be prepared at the cell voltage of 1.7 2.1 V in this reaction system.The silicon material have cluster-like structure which are made of silicon nanoparticles in 20 100 nm size.Interestingly,the cluster-like nano structure of the silicon can be tuned by the used cell voltage.The purity,yield and the energy cost of silicon product prepared at the optimized cell voltage are discussed.The purity of the silicon product could be further improved,hence this method is promising for the preparation of solar grade silicon in future.     

Low CO content hydrogen production from oxidative steam reforming of ethanol over CuO-CeO₂ catalysts at low-temperature

CuO-CeO2 catalysts were prepared by a urea precipitation method for the oxidative steam reforming of ethanol at low-temperature.The catalytic performance was evaluated and the catalysts were characterized by inductively coupled plasma atomic emission spectroscopy,X-ray diffraction,temperature-programmed reduction,field emission scanning electron microscopy and thermo-gravimetric analysis.Over CuOCeO2 catalysts,H2 with low CO content was produced in the whole tested temperature range of 250–450 C.The non-noble metal catalyst 20CuCe showed higher H2production rate than 1%Rh/CeO2 catalyst at 300–400 C and the advantage was more obvious after 20 h testing at400 C.These results further confirmed that CuO-CeO2 catalysts may be suitable candidates for low temperature hydrogen production from ethanol.     

Photoelectrode Characteristics of Partially Hydrolyzed Aluminum Phthalocyanine Chloride/Fullerene C₆₀ Composite Nanoparticles Working in a Water Phase

Photoelectrochemical measurements were used to study the photoelectrode characteristics of composite nanoparticles composed of fullerene C₆₀ and partially hydrolyzed aluminum phthalocyanine chloride (AlPc). In cyclic voltammetry measurements, the electrodes coated with the composite nanoparticles were found to have photoanodic [electron donor: 2-mercaptoethanol (ME)] and photocathodic (electron acceptor: O₂) characteristics similar to those of the vapor-deposited p/n junction electrode. Their photoanodic features were further investigated with respect to the transient photocurrent response to light irradiation and the dependence on ME concentration (under potentiostatic conditions), from which it was noted that there was a decrease in the initial spiky photocathodic current and saturation of the steady-state photoanodic current at a higher ME concentration. Thus, the reaction kinetics was probably dominated by charge transport process. Moreover, external and internal quantum efficiency spectrum measurements indicated that the composite nanoparticles responded to the full spectrum of visible light ( < 880 nm) for both the photoanodic and photocathodic current. The present research will assist comprehension of photocatalytic behavior of the composite nanoparticles.     

Synthesis and structure of [UO<Subscript>2</Subscript>(C<Subscript>2</Subscript>O<Subscript>4</Subscript>){CONH<Subscript>2</Subscript>N(CH<Subscript>3</Subscript>)<Subscript>2</Subscript>}<Subscript>2</Subscript>]

The single crystals of [UO₂(C₂O₄){CONH₂N(CH₃)₂}₂] were synthesized and studied by X-ray diffraction. The crystals are monoclinic, a = 7.461(2) Å, b = 8.828(2) Å, c = 11.756(2) Å, β = 107.21(3)°, space group Pc, Z = 2, R = 2.94%. The structure comprises infinite chains [UO₂(C₂O₄){CONH₂N(CH₃)₂}₂] extended along [001] and corresponding to the AT¹¹M ₂ ¹ crystallochemical group (A = UO ₂ ²⁺ , T¹¹ = C₂O ₄ ^2? , M¹ = N,N-CONH₂N(CH₃)₂) of uranyl complexes. The chains are connected into a three-dimensional framework by hydrogen bonds involving the oxygen atoms of oxalate and uranyl ions and the N,N-dimethylcarbamide methyl groups.     

Supramolecular 2D structure of [Co(2-Me-Pyz)<Subscript>2</Subscript>(H<Subscript>2</Subscript>O)<Subscript>4</Subscript>](NO<Subscript>3</Subscript>)<Subscript>2</Subscript>

The complex [Co(2-Me-Pyz)₂(H₂O)₄](NO₃)₂ is synthesized and its structure is determined. The crystals are monoclinic: space group P2₁/n, a = 10.685(2) Å, b = 6.837(1), c = 12.515(3) Å, β = 91.84(3)°, V = 913.8(3) ų, ρ_calcd = 1.042 g/cm ³, Z = 2. The Co²⁺ ion (in the inversion center) is coordinated at the vertices of the distorted octahedron by two nitrogen atoms of methylpyrazine and four oxygen atoms of the water molecules (Co(1)–N(1) 2.180(3), average Co(1)–O(w) 2.079(3) Å, angles at the Co atom 87.9(1)–92.1(1)°). Supramolecular pseudometallocycles are formed in the structure through the O(w)–H…N(1) hydrogen bonds between the coordinated H₂O molecules and the terminal nitrogen atoms of the 2-methylpyrazine molecules. Their interaction results in the formation of supramolecular layers joined by the NO₃ groups into a three-dimensional framework.     

ESR Study of the Formation of O<Stack><Subscript>2</Subscript><Superscript>−</Superscript></Stack> Radical Anions on Oxidized CeO<Subscript>2</Subscript> and CeO<Subscript>2</Subscript>/ZrO<Subscript>2</Subscript> Adsorbing a CO + O<Subscript>2</Subscript> Mixture

It is demonstrated by ESR measurements that O ₂ ⁻ (CO + O₂) radical anions result from CO + O₂ adsorption on the oxidized surface of CeO₂. These radical anions are stabilized in the coordination sphere of Ce⁴⁺ cations located in isolated and associated anionic vacancies. This reaction shows an activation behavior determined by CO adsorption. The variation of O ₂ ⁻ (CO + O₂) concentration with CO adsorption temperature suggests that surface carbonates and carboxylates participate in this reaction. In the (0.5– 10.0)%CeO₂/ZrO₂ system, O ₂ ⁻ forms on supported CeO₂ and is stabilized on Ce⁴⁺ and Zr⁴⁺ cations. The stability of O ₂ ⁻ -Ce⁴⁺ complexes is lower on supported CeO₂ than on unsupported CeO₂, indicating a strong interaction between the cerium cations and the support.__________Translated from Kinetika i Kataliz, Vol. 46, No. 3, 2005, pp. 423–429.Original Russian Text Copyright © 2005 by Il’ichev, Kuli-zade, Korchak.     

Specific heat on Sr<Subscript>2</Subscript>Nb<Subscript>2</Subscript>O<Subscript>7</Subscript> and Sr<Subscript>2</Subscript>Ta<Subscript>2</Subscript>O<Subscript>7</Subscript>

Summary Specific heats on the single crystals of Sr₂Nb₂O₇, Sr₂Ta₂O₇ and (Sr_1-xBa_x)₂Nb₂O₇ were measured in a wide temperature range of 2-600 K. Heat anomalies of a λ-type were observed at the incommensurate phase transition of T_INC (=495 K) on Sr₂Nb₂O₇ and at the super-lattice phase transition of T_SL (=443 K) on Sr₂Ta₂O₇; the transition enthalpies and the transition entropies were estimated. Furthermore, a small heat anomaly was observed at the low temperature ferroelectric phase transition of T_LOW (=95 K) on Sr₂Nb₂O₇. The transition temperature T_LOW decreases with increasing Ba content x and it vanishes for samples of x>2%.     

NaBO<Subscript>2</Subscript>-Na<Subscript>2</Subscript>CO<Subscript>3</Subscript>-Na<Subscript>2</Subscript>MoO<Subscript>4</Subscript>-Na<Subscript>2</Subscript>WO<Subscript>4</Subscript> quaternary system

This is the first study of the NaBO₂-Na₂CO₃-Na₂MoO₄-Na₂WO₄ quaternary system by differential thermal analysis. Na₂[MoO_4(x)WO_{4(1 − x)}] solid solutions in the quaternary system are found to not decompose.     

Structure and some properties of [UO<Subscript>2</Subscript>CrO<Subscript>4</Subscript>{CH<Subscript>3</Subscript>CON(CH<Subscript>3</Subscript>)<Subscript>2</Subscript>}<Subscript>2</Subscript>]

A new complex [UO₂CrO₄{CH₃CON(CH₃)₂}₂] (I) was studied by thermal analysis, IR spectroscopy, and X-ray crystallography. The crystals are monoclinic: a = 13.8108(11) Å, b = 8.6804(7) Å, c = 13.0989(10) Å, β = 104.777(1)°, V = 1518.4(2) ų, space group P2₁/c, Z = 4, R = 2.39%. The structure of I contains infinite chains of the [UO₂CrO₄{CH₃CON(CH₃)₂}₂] composition running along [001]; the complex belongs to the AT¹¹M¹ ₂ crystal-chemical group (A = UO ₂ ²⁺ , T¹¹ = CrO ₄ ^2? , M¹ = CH₃CON(CH₃)₂) of uranyl complexes. The chains are linked into a three-dimensional framework due to hydrogen bonds between oxygen atoms of chromate ions and hydrogen atoms of methyl groups of the dimethylacetamide.     

Controllable synthesis of high loading LiFePO₄/C nanocomposites using bimodal mesoporous carbon as support for high power Li-ion battery cathodes

Mesoporous LiFePO4/C composites containing 80 wt% of highly dispersed LiFePO4 nanoparticles(4-6 nm) were fabricated using bimodal mesoporous carbon(BMC) as continuous conductive networks. The unique pore structure of BMC not only promises good particle connectivity for LiFePO4, but also acts as a rigid nano-confinement support that controls the particle size. Furthermore, the capacities were investigated respectively based on the weight of LiFePO4 and the whole composite. When calculated based on the weight of the whole composite, it is 120 mAh·g-1at 0.1 C of the high loading electrode and 42 mAh·g-1at 10 C of the low loading electrode. The electrochemical performance shows that high LiFePO4 loading benefits large tap density and contributes to the energy storage at low rates, while the electrode with low content of LiFePO4 displays superior high rate performance, which can mainly be due to the small particle size, good dispersion and high utilization of the active material, thus leading to a fast ion and electron diffusion.     

Synthesis and study of sodium triuranate Na<Subscript>2</Subscript>(UO<Subscript>2</Subscript>)<Subscript>3</Subscript>O<Subscript>3</Subscript>(OH)<Subscript>2</Subscript>

Sodium triuranate Na₂(UO₂)₃O₃(OH)₂ was synthesized by the reaction between aqueous uranyl acetate solution and aqueous sodium nitrate solution under hydrothermal conditions at 200°C. The composition and structure of the synthesized compound were determined, and its dehydration and thermal decomposition were studied, by chemical analysis, X-ray diffraction, IR spectroscopy, and thermal analysis.     

Thermal synthesis of the CeO<Subscript>2</Subscript>-PrO<Subscript>2</Subscript>-Nd<Subscript>2</Subscript>O<Subscript>3</Subscript>pigments

Summary The synthesis of new compounds based on the CeO₂-PrO₂-Nd₂O₃system, which can be used as pigments for colouring of ceramic glazes, is investigated in our laboratory. The optimum conditions for the syntheses of these compounds have been estimated. The methods of thermal analysis provided first information about the temperature region of the formation of the pigments investigated. The synthesis of these compounds was followed by thermal analysis using STA 449/C Jupiter (Netzsch, Germany).