Preparation of ZnFe<Subscript>2</Subscript>O<Subscript>4</Subscript> nanoparticles by mechanical alloying and annealing for sensitizing C-modified TiO<Subscript>2</Subscript> and acquirement of efficient photocatalyst

ZnFe₂O₄ nanoparticles sensitized by C-modified TiO₂ hybrids (ZnFe₂O₄–TiO₂/C) were successfully prepared by a feasible method. The ZnFe₂O₄ nanoparticles were prepared by mechanical alloying and annealing. The residual organic compounds in the synthetic process of TiO₂ were selected as the carbon source. The as-prepared composites were characterized by X-ray diffraction, Raman spectroscopy, X-ray fluorescence, transmission electron microscopy, X-ray photoelectron spectroscopy, ultraviolet–visible light diffuse reflectance spectroscopy (UV–Vis) and N₂ adsorption–desorption analysis. The photocatalytic activity of the photocatalysts was measured by degradation of methyl orange under ultraviolet (UV) light and simulated solar irradiation, respectively. The results show that the carbon did not enter the TiO₂ lattice but adhered to the surface of TiO₂. The photocatalytic activity of the as-prepared C-modified TiO₂ (TiO₂/C) improved both under UV and simulated solar light irradiation, but the improvement was not dramatic. Introduction of ZnFe₂O₄ into the TiO₂/C could enhance the absorption spectrum range. The ZnFe₂O₄–TiO₂/C hybrids exhibited a higher photocatalytic activity both than that of the pure TiO₂ and TiO₂/C under either UV or simulated solar light irradiation. The complex synergistic effect plays an important role in improving the photocatalytic performance of ZnFe₂O₄–TiO₂/C composites. The optimum photocatalytic performance was obtained from the ZnFe₂O₄(0.8 wt%)–TiO₂/C sample.     

Structural characterization and photocatalytic properties of novel Bi<Subscript>2</Subscript>FeVO<Subscript>7</Subscript>

Bi₂FeVO₇ was prepared by a solid-state reaction technique for the first time and the structural and photocatalytic properties of Bi₂FeVO₇ were studied. The results shows that this compound crystallized in the tetragonal crystal system with space group I4/mmm. Moreover, the band gap of Bi₂FeVO₇ was estimated to be about 2.22(6) eV. For the photocatalytic water splitting reaction, H₂ or O₂ evolution was observed from pure water with Bi₂FeVO₇ as the photocatalyst by ultraviolet light irradiation. Degradation of aqueous methylene blue (MB) dye by photocatalytic way over this compound was further studied under visible light irradiation. Bi₂FeVO₇ shows higher catalytic activity compared to TiO₂ (P-25) for MB photocatalytic degradation under visible light irradiation. Complete removal of aqueous MB was realized after visible light irradiation for 170 min with Bi₂FeVO₇ as the photocatalyst. The reduction of the total organic carbon (TOC) and the formation of inorganic products, SO ₄ ²⁻ and NO ₃ ⁻ revealed the continuous mineralization of aqueous MB during the photocatalytic course.     

Photocatalytic degradation of trichloroethylene on platinum ion-doped TiO<Subscript>2</Subscript> under visible light irradiation

Porous platinum ion-doped TiO₂ (Pt–TiO₂) was prepared by a sol–gel method and demonstrated to have superior photocatalytic activity for the photodegradation of gaseous trichloroethylene (TCE) under visible light (VL) irradiation from a xenon lamp equipped with 422-nm cut-off filter. Kinetic studies were performed to clarify the effect of the doping amounts, space times, VL intensity, and mole fractions of TCE, O₂, and H₂O on the degradation of TCE. Under ultraviolet (UV) irradiation, the photocatalytic activity of Pt–TiO₂ was the same as that of TiO₂, indicating that the doped Pt ion did not act as a recombination center for the photogenerated holes and electrons. Based on the kinetic data and reaction products, we conclude that the photocatalytic degradation of TCE on Pt–TiO₂ under VL irradiation proceeds similarly to TiO₂ under UV irradiation. We also performed the photocatalytic degradation of TCE at the space time of 7.5 × 10⁷ g s mol^?1 in a tubular reactor packed with the Pt–TiO₂ pellets which are more suitable than the Pt–TiO₂ powder for the practical remediation of the contaminated gas. TCE was completely degraded, i.e. 100% conversion was achieved under VL irradiation but only a small quantity of CO₂ was formed with the stoichiometric ratio of [CO₂]_formed/[TCE]_degraded of ca. 0.33. By switching the gas stream containing TCE to humid air, more CO₂ was formed, indicating that the dichloroacetates accumulated on the Pt–TiO₂ surface are photodegradable to CO₂ under VL irradiation.     

Microstructure of SiO<Subscript>2</Subscript>/TiO<Subscript>2</Subscript> hybrid electrospun nanofibers and their application in dye degradation

SiO₂/TiO₂ hybrid nanofibers were prepared by electrospinning and applied for photocatalytic degradation of methylene blue (MB). The phase structure, specific surface area, and surface morphologies of the SiO₂/TiO₂ hybrid nanofibers were characterized through thermogravimetry (TG), X-ray diffraction (XRD) analysis, Brunauer–Emmett–Teller (BET) analysis, scanning electron microscopy (SEM), etc. XRD measurements indicated that doping of silica into TiO₂ nanofibers can delay the phase transition from anatase to rutile and decrease the grain size. SEM and BET characterization proved that silica doping can remarkably enhance the porosity of the SiO₂/TiO₂ hybrid nanofibers. The MB adsorption capacity and photocatalytic activity of the SiO₂/TiO₂ hybrid nanofibers were distinguished experimentally. It was found that, although increased silica doping content could enhance the MB adsorption capacity, the intrinsic photocatalytic activity gradually dropped. The SiO₂ (10 %)/TiO₂ composite nanofibers exhibited the highest MB degradation rate, being superior to SiO₂ (20 %)/TiO₂ or pure TiO₂.     

Preparation and photocatalytic activity of TiO<Subscript>2</Subscript> films with Ni nanoparticles

Titania thin films were synthesized by sol–gel dip-coating method with metallic Ni nanoparticles synthesized separately from an organometallic precursor Ni(COD)₂ (COD = cycloocta-1,5-diene) in presence of 1,3-diaminopropane as a stabilizer. Titania was obtained from a titanium isopropoxide precursor solution in presence of acetic acid. A Ni/TiO₂ sol system was used to coat glass substrate spheres (6, 4 and 3 mm diameter sizes), and further heat treatment at 400 °C was carried out to promote the crystallization of titania. XRD analysis of the TiO₂ films revealed the crystallization of the anatase phase. Transmission Electron Microscopy (TEM) and High Resolution TEM studies of Ni nanoparticles before mixing with the TiO₂ solution revealed the formation of Ni nanostructures with an average size of 5–10 nm. High-angle annular dark-field images of the Ni/TiO₂ system revealed well-dispersed Ni nanoparticles supported on TiO₂ and confirmed by AFM analysis. The photocatalytic activity of the Ni/TiO₂ films was evaluated in hydrogen evolution from the decomposition of ethanol using a mercury lamp for UV light irradiation. Titania films in presence of Ni nanoparticles show higher efficiency in their photocatalytic properties in comparison with TiO₂.     

A P/N type compounded Cu<Subscript>2</Subscript>O/TiO<Subscript>2</Subscript> photo-catalytic membrane for organic pollutant degradation

A heterojunction thin film consisting of n-type titanium dioxide (TiO₂) and p-type cuprous oxide (Cu₂O) was fabricated on an FTO conducting glass. The TiO₂ films were grown on the FTO glass by sol–gel and spray pyrolysis methods, and Cu₂O was deposited on it via the hydrothermal method. The morphology, crystalline structure, and optical absorption characteristics were studied by scanning electron microscopy, X-ray diffraction, and ultraviolet–visible diffuse reflectance spectrum, respectively. The results show that the surface of the Cu₂O/TiO₂ film was composed of net and large grains, which contributed to a large specific surface area. The crystal phase of the TiO₂ in the Cu₂O/TiO₂ film remained anatase. The crystal phase of the Cu₂O could not be detected as it is found in traces. The Cu₂O/TiO₂ film had a stronger optical absorption ability than the pure TiO₂ film. To investigate catalytic activity, a photocatalytic degradation experiment of the Cu₂O/TiO₂ film was performed in a homemade thin-layer micro-reactor. The photocatalytic degradation of methylene blue increased with increasing amounts of deposited Cu₂O until a maximum limit was reached. The photocatalytic activity might have declined with an increase in Cu₂O content. The metallic oxide has the potential to screen other photocatalysts from the UV source.     

Synthesis,Characterization and Photocatalytic Application of TiO<Subscript>2</Subscript>/SnO<Subscript>2</Subscript> Nanocomposite Obtained Under Non-thermal Plasma Condition at Atmospheric Pressure

A plasma-assisted synthesis of TiO₂/SnO₂ nanocomposite is described. In this approach, a precursor containing a mixture of [TiCl₃ and SnCl₂] exposed to electric discharge was oxidized by plasma-generated reactive species (HO^·/H₂O = 2.85 eV/SHE). SnO₂ microstructures with a diameter of 10–40 µm were coated by thin layers TiO₂ nanorods with mean diameter of 6–8 nm. The obtained TiO₂/SnO₂ nanocomposite was characterized by transmission and scanning electron microscopy, X-ray diffraction and Fourier transform infrared. TiO₂/SnO₂ nanocomposite was found to be a promising new material for the photocatalytic discoloration of aqueous Remazol Brilliant Blue-R dye under daylight and UVA light sources, due to the combined effects of large specific surface area and heterojunction which efficiently separates the electron–hole pairs delaying the charge recombination. The leaching test indicated that the nanocomposite is stable easily reusable.     

Enhanced visible light photocatalytic H<Subscript>2</Subscript> evolution over CeO<Subscript>2</Subscript> loaded with Pt and CdS

CdS-Pt@CeO₂ ternary composites are successfully prepared by an in situ redox precipitation followed by a subsequent precipitation. The prepared CdS-Pt@CeO₂ sample exhibits high photocatalytic activity for hydrogen evolution from lactic acid aqueous solution under visible light irradiation, with a H₂-evolation rate of 20.09 mmol h^?1g^?1 and apparent quantum yield (AQY) of 15.32%. With techniques such as XRD, TEM, DRS, XPS, N₂ adsorption/desorption and electrochemistry measurements, the physicochemical properties of the CdS-Pt@CeO₂ ternary composites are discussed, and a possible mechanism for the hydrogen evolution is proposed.     

Ce(4+) doped TiO<Subscript>2</Subscript> thin films: Characterization and photocatalysis

Undoped and Ce(4+) doped TiO₂ thin films were prepared by sol-gel method. The samples were characterized using scanning electron microscopy, the photocatalytic reactivity was evaluated by degradation of methylene blue in the aqueous solution. 0.5 wt. % Ce(4+) doped TiO₂ thin films calcined at 400°C show the highest photocatalytic activity. The text was submitted by the authors in English.     

Dielectric properties and I-V characteristics of (Pb<Subscript>0.4</Subscript>Sr<Subscript>0.6</Subscript>)TiO<Subscript>3</Subscript> thin films improved by TiO<Subscript>2</Subscript> buffer layers

A TiO₂ thin buffer layer was introduced between the (Pb_0.4Sr_0.6)TiO₃ (PST) film and the Pt/Ti/SiO₂/Si substrate in an attempt to improve their electrical properties. Both TiO₂ and PST layers were prepared by a chemical solution deposition method. It was found that the TiO₂ buffer layer increased the (100)/(001) preferred orientation of PST and decreased the surface roughness of the films, leading to an enhancement in electrical properties including an increase in dielectric constant and in its tunability by DC voltage, as well as a decrease in dielectric loss and leakage current density. At an optimized thickness of the TiO₂ buffer layer deposited using 0.02 mol/l TiO₂ sol, the 330-nm-thick PST films had a dielectric constant, loss and tunability of 1126, 0.044 and 60.7% at 10 kHz, respectively, while the leakage current density was 1.95 × 10⁻⁶ A/cm² at 100 kV/cm.     

Catalytic Properties of TiO<Subscript>2</Subscript>/Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> Nanoparticles in Plasma Chemical Treatment

We proposed here a new process coupling dielectric barrier discharge (DBD) plasma with magnetic photocatalytic material nanoparticles for improving yield in DBD degradation of methyl orange (MO). TiO₂ doped Fe₃O₄ (TiO₂/Fe₃O₄) was prepared by the sol-gel method and used as a new type of magnetic photocatalyst in DBD system. It was found that the introduction of TiO₂/Fe₃O₄ in DBD system could effectively make use of the energy generated in DBD process and improve hydroxyl radical contributed by the main surface Fenton reaction, photocatalytic reaction and catalytic decomposition of dissolved ozone. Most part of MO (88%) was degraded during 30 min at peak voltage of 13 kV and TiO₂/Fe₃O₄ load of 100 mg/L, with a rate constant of 0.0731 min^?1 and a degradation yield of 7.23 g/(kW h). The coupled system showed higher degradation efficiency for MO removal.     

Synthesis,characterization of B-doped TiO<Subscript>2</Subscript> nanotubes with high photocatalytic activity

B-doped TiO₂ nanotubes (B/TiO₂ NTs) were prepared by the combination of sol–gel process with hydrothermal treatment. The prepared catalysts were characterized by XRD, TEM and XPS. The photocatalytic activity of B/TiO₂ NTs was evaluated through the photodegradation of aqueous methyl orange. The results demonstrated that the 1.5% B/TiO₂ NTs calcined at 300 °C possessed the best photocatalytic activity. Compared with pure TiO₂ nanotubes, the doping with B significantly enhanced the photocatalytic efficiency.     

Direct fabrication of anatase TiO<Subscript>2</Subscript> hollow microspheres for applications in photocatalytic hydrogen evolution and lithium storage

Hollow titanium dioxide (TiO₂) microspheres were synthesized in one step by employing tetrabutyl orthotitanate (TBOT) as a precursor through a facile solvothermal method in the presence of NH₄HCO₃. XRD analysis indicated that anatase TiO₂ can be obtained directly without further annealing. TiO₂ hollow microspheres with diameters in the range of 1.0–4.0 μm were confirmed through SEM and TEM measurements. The specific surface area was measured to be 180 m² g^?1 according to the nitrogen adsorption–desorption isotherms. Superior photocatalytic performance and good lithium storage properties were achieved for resultant TiO₂ samples. The H₂ evolution rate of the optimal sample is about 0.66 mmol h^?1 after loaded with 1 wt.% Pt (20 mg samples). The reversible capacity remained 143 mAh g^?1 at a specific current of 300 mA g^?1 after 100 charge–discharge cycles. This work provides a facile strategy for the preparation of hollow titanium dioxide microspheres and demonstrates their promising photocatalytic H₂ evolution and the lithium storage properties.

Open image in new window

Graphical abstract Hollow titanium dioxide spheres are directly synthesized via a facile template-free solvothermal method with the presence of NH₄HCO₃ based on inside-out Ostwald ripening (see picture), and demonstrated both as a photocatalyst for water splitting and a promising anode material for lithium-ion batteries. Superior photocatalytic performance and excellent lithium storage properties are achieved for resultant TiO₂ hollow microspheres.

     

Photocatalysis enhancement of CaAl<Subscript>2</Subscript>O<Subscript>4</Subscript>:Eu<Superscript>2+</Superscript>, Nd<Superscript>3+</Superscript>@TiO<Subscript>2</Subscript> composite powders

CaAl₂O₄:Eu²⁺, Nd³⁺@TiO₂ composite powders were synthesized by a sol–gel method under mild conditions (i.e. low temperature and ambient pressure). The as-prepared powders were characterized by transmission electron microscopy (TEM) and analyzed by X-ray diffraction (XRD). The photocatalytic behavior of the TiO₂-base surfaces was evaluated by the degradation of nitrogen monoxide gas. It suggested that CaAl₂O₄:Eu²⁺, Nd³⁺@TiO₂ composite powders were composed of anatase titania and that CaAl₂O₄:Eu²⁺, Nd³⁺. TiO₂ particles were deposited on the surface of CaAl₂O₄:Eu²⁺, Nd³⁺ to form uniform film. CaAl₂O₄:Eu²⁺, Nd³⁺@TiO₂ composite powders exhibited higher photocatalytic activity compared with pure TiO₂ under visible light. And the result also clearly indicated that the long afterglow phosphor absorbed and stored lights for the TiO₂ to remain photocatalytic activity in the dark.     

Influence of ThO<Subscript>2</Subscript> on the photocatalytic activity of TiO<Subscript>2</Subscript>

Microcomposites consisting of TiO₂ (or Ce-doped TiO₂) and ThO₂ (0.5–2% of the TiO₂ mass) are produced by sol-gel synthesis of TiO₂ in presence of ThO₂. X-ray diffraction study reveals the effects of ThO₂ (compared to the ThO₂-free TiO₂, obtained by the same method) on the anatase interplanar distances, crystallites size and phase composition. The photocatalytic tests in presence of the composites under UV irradiation reveal an increase of the Malachite Green degradation rate constant. The effect depends on the Th relative content, temperature of annealing of the catalyst and addition of other doping agent. The highest photocatalytic activity is observed for TiO₂ obtained at 550°C and containing 1% ThO₂. The composite exhibits activity in dark, also. The presence of Ce⁴⁺ ions is not an obligatory requirement for the realization of the ThO₂ effect. The reported results suggest that the radioactivity of the Th and/or its decay products is one of the main factors responsible for the increased photocatalytic activity of TiO₂.      

Degradation of ofloxacin by UVA-LED/TiO<Subscript>2</Subscript> nanotube arrays photocatalytic fuel cells

The degradation of ofloxacin (OFX) at low concentration in aqueous solution by UVA-LED/TiO₂ nanotube arrays photocatalytic fuel cells (UVA-LED/TiO₂ NTs PFCs) was investigated. TiO₂ nanotube arrays (TiO₂ NTs) photoanode prepared by anodization-constituted anatase–rutile bicrystalline framework. The results indicated that the degradation efficiency of OFX by UVA-LED/TiO₂ NTs PFC was significantly enhanced by 14.3% compared with UVA-LED/TiO₂ NTs photocatalysis. The pH affected the degradation efficiency markedly; the highest degradation efficiency (95.0%) and the pseudo-first-order reaction rate constant k value (0.049 min^?1) were achieved in neutral condition (pH 7.0). The degradation efficiency increased with the increasing concentration of dissolved oxygen (DO) in the UVA-LED/TiO₂ NTs PFC. The main reactive species of OFX degradation are positive holes (h⁺) and superoxide ion radicals (O ₂ ^·? ) in a DO sufficient condition. Furthermore, the possible pathways of OFX degradation were proposed.     

TiO<Subscript>2</Subscript>/SiO<Subscript>2</Subscript> hybrid nanomaterials: synthesis and variable UV-blocking properties

Silica and core–shell structured titania/silica (TiO₂/SiO₂) nanoparticles with particles size ranging from tens to hundreds of nanometers were prepared and deposited onto cotton fabric substrates by sol–gel process. The morphologies of the nanoparticles were characterized by field-emission scanning electron microscope (FE-SEM). The photocatalytic decomposition properties as well as UV-blocking properties of the fabrics treated with SiO₂ and TiO₂/SiO₂ nanoparticles were investigated.     

Study of Fe-doped V<Subscript>2</Subscript>O<Subscript>5</Subscript>/TiO<Subscript>2</Subscript> catalyst for an enhanced NH<Subscript>3</Subscript>-SCR in diesel exhaust aftertreatment

Selective catalytic reduction (SCR) with ammonia has been considered as the most promising technology, as its effect deals with the NO_X. Novel Fe-doped V₂O₅/TiO₂ catalysts were prepared by sol–gel and impregnation methods. The effects of iron content and reaction temperature on the catalyst SCR reaction activity were explored by a test device, the results of which revealed that catalysts could exhibit the best catalytic activity when the iron mass ratio was 0.05%. It further proved that the VTiFe (0.05%) catalyst performed the best in denitration and its NO_X conversion reached 99.5% at 270 °C. The outcome of experimental procedures: Brunauer–Emmett–Teller surface area, X-ray powder diffraction, transmission electron microscopy, X-ray photoelectron spectroscopy, temperature-programmed reduction and adsorption (H₂-TPR, NH₃-TPD) techniques showed that the iron existed in the form of Fe³⁺ and Fe²⁺ and the superior catalytic performance was attributed to the highly dispersed active species, lots of surface acid sites and absorbed oxygen. The modified Fe-doped catalysts do not only have terrific SCR activities, but also a rather broad range of active temperature which also enhances the resistance to SO₂ and H₂O.     

Influence of NH<Subscript>3</Subscript>-treating temperature on visible light photocatalytic activity of N-doped P<Subscript>25</Subscript>-TiO<Subscript>2</Subscript>

The influence of NH₃-treating temperature on the visible light photocatalytic activity of N-doped P₂₅-TiO₂ as well as the relationship between the surface composition structure of TiO₂ and its visible light photocatalytic activity were investigated. The results showed that N-doped P₂₅-TiO₂ treated at 600°C had the highest activity. The structure of P₂₅-TiO₂ was converted from anatase to rutile at 700°C. Moreover, no N-doping was detected at the surface of P₂₅-TiO₂. There was no simply linear relationship between the visible light photocatalytic activity and the concentration of doped nitrogen, and visible light absorption. The visible light photocatalytic activity of N-doped P₂₅-TiO₂ was mainly influenced by the synergistic action of the following factors: (i) the formation of the single-electron-trapped oxygen vacancies (denoted as V_o^·); (ii) the doped nitrogen on the surface of TiO₂; (iii) the anatase TiO₂ structure.     

Preparation of nanocrystalline Fe-doped TiO<Subscript>2</Subscript> powders as a visible-light-responsive photocatalyst

Nanocrystalline Fe-doped TiO₂ powders were prepared using TiOSO₄, urea, and Fe(NO₃)₃ · 9H₂O as precursors through a hydrothermal method. The as-synthesized yellowish-colored powders are composed of anatase TiO₂, identified by X-ray diffraction (XRD). The grain size ranged from 9.7 to 12.1 nm, calculated by Scherrer’s method. The specific surface area ranged from 141 to 170 m²/g, obtained by the Brunauer–Emmett–Teller (BET) method. The transmission electron microscopy (TEM) micrograph of the sample shows that the diameter of the grains is uniformly distributed at about 10 nm, which is consistent with that calculated by Scherrer’s method. Fe³⁺ and Fe²⁺ have been detected on the surface of TiO₂ powders by X-ray photoelectron spectroscopy (XPS). The UV–Vis diffuse reflection spectra indicate that the light absorption thresholds of the Fe-doped TiO₂ powders have been red-shifted into the visible light region. The photocatalytic activity of the Fe-doped TiO₂ was evaluated through the degradation of methylene blue (MB) under visible light irradiation. The Fe-doped TiO₂ powders have shown good visible-light photocatalytic activities and the maximum degradation ratio is achieved within 4.5 h.