Effects of dopant on the electrochemical properties of Li<Subscript>4</Subscript>Ti<Subscript>5</Subscript>O<Subscript>12</Subscript> anode materials

The effects of dopant on the electrochemical properties of spinel-type Li_3.97M_0.1Ti_4.94O₁₂ (M = Mn, Ni, Co) and Li_(4-x/3)Cr_xTi_(5-2x/3)O₁₂(x = 0.1, 0.3, 0.6, 0.9, 1.5) were systematically investigated. Charge-discharge cycling were performed at a constant current density of 0.5 mA/cm² between the cut-off voltages of 3.0 and 1.0 V, the experimental results showed that Cr³⁺ dopant improved the reversible capacity and cycling stability over the pristine Li₄Ti₅O₁₂. The substitution of the Mn³⁺ and Ni³⁺ slightly decreased the capacity of the Li₄Ti₅O₁₂. Dopants such as Co³⁺ to some extent worsened the electrochemical performance of the Li₄Ti₅O₁₂.     

Synthesis and electrochemical performances of Li4Ti4.95Al0.05O12/C as anode material for lithium-ion batteries

Spinel compounds Li₄Ti_5−xAl_xO₁₂/C (x=0, 0.05) were synthesized via solid state reaction in an Ar atmosphere, and the electrochemical properties were investigated by means of electronic conductivity, cyclic voltammetry, and charge-discharge tests at different discharge voltage ranges (0-2.5 V and 1-2.5 V). The results indicated that Al³⁺ doping of the compound did not affect the spinel structure but considerably improved the initial capacity and cycling performance, implying the spinel structure of Li₄Ti₅O₁₂ was more stable when Ti⁴⁺ was substituted by Al³⁺, and Al³⁺ doping was beneficial to the reversible intercalation and deintercalation of Li⁺. Al³⁺ doping improved the reversible capacity and cycling performance effectively especially when it was discharged to 0 V.     

Electrospinning preparation of one-dimensional Co<Superscript>2+</Superscript>-doped Li<Subscript>4</Subscript>Ti<Subscript>5</Subscript>O<Subscript>12</Subscript> nanofibers for high-performance lithium ion battery

One-dimensional Co²⁺-doped Li₄Ti₅O₁₂ nanofibers with a diameter of approximately 500 nm have been synthesized via a one-step controllable electrospinning method. The Co²⁺-doped Li₄Ti₅O₁₂ nanofibers were systematically characterized by XRD, ICP, TEM, SEM, BET, EDS mapping, and XPS. Based on the cubic spinel structure and one-dimensional effect of Li₄Ti₅O₁₂, Co²⁺-doped Li₄Ti₅O₁₂ nanofibers exhibit the enlarged lattice volume, reduced particle size and enhanced electrical conductivity. More importantly, Co²⁺-doped Li₄Ti₅O₁₂ nanofibers as a lithium ion battery anode electrode performs superior electrochemical performance than undoped Li₄Ti₅O₁₂ electrode in terms of electrochemical measurements. Particularly, the reversible capacity of Co²⁺-doped Li₄Ti₅O₁₂ electrode reaches up to 140.1 mAh g^?1 and still maintains 136.5 mAh g^?1 after 200 cycles at a current rate of 5 C. Therefore, one-dimensional Co²⁺-doped Li₄Ti₅O₁₂ nanofiber electrodes, showing high reversible capacity and remarkable recycling property, could be a potential candidate as an anode material.     

Pr-modified Li<Subscript>4</Subscript>Ti<Subscript>5</Subscript>O<Subscript>12</Subscript> nanofibers as an anode material for lithium-ion batteries with outstanding cycling performance and rate performance

Pr-doped Li₄Ti₅O₁₂ in the form of Li_4?x/3Ti_5?2x/3Pr_xO₁₂ (x = 0, 0.01, 0.03, 0.05, and 0.07) was synthesized successfully by an electrospinning technique. ICP shows that the doped samples are closed to the targeted samples. XRD analysis demonstrates that traces of Pr³⁺ can enlarge the lattice parameter of Li₄Ti₅O₁₂ from 8.3403 to 8.3765 Å without changing the spinel structure. The increase of lattice parameter is beneficial to the intercalation and de-intercalation of lithium-ion. XPS results identify the existence form of Ti is mainly Ti⁴⁺ and Ti³⁺ in minor quantity in Li_4?x/3Ti_5?2x/3Pr_xO₁₂ (x = 0.05) samples due to the small amount of Pr³⁺. The transition from Ti⁴⁺ to Ti³⁺ is conducive to the electronic conductivity of Li₄Ti₅O₁₂. FESEM images show that all the nanofibers are well crystallized with a diameter of about 200 nm and distributed uniformly. The results of electrochemical measurement reveal that the 1D Li_4?x/3Ti_5?2x/3Pr_xO₁₂ (x = 0.05) nanofibers display enhanced high-rate capability and cycling stability compared with that of undoped nanofibers. The high-rate discharge capacity of the Li_4?x/3Ti_5?2x/3Pr_xO₁₂ (x = 0.05) samples is excellent (101.6 mAh g^?1 at 50 °C), which is about 58.48 % of the discharge capacity at 0.2 °C and 4.3 times than that of the bare Li₄Ti₅O₁₂ (23.5 mA g^?1). Even at 10 °C (1750 mA g^?1), the specific discharge capacity is still 112.8 mAh g^?1 after 1000 cycles (87.9 % of the initial discharge capacity). The results of cyclic voltammograms (CV) and electrochemical impedance spectroscopy (EIS) illustrate that the Pr-doped Li₄Ti₅O₁₂ electrodes possess better dynamic performance than the pure Li₄Ti₅O₁₂, further confirming the excellent electrochemical properties above.     

Synthesis and electrochemical performance of hole-rich Li4Ti5O12 anode material for lithium-ion secondary batteries

Hole-rich Li₄Ti₅O₁₂ composites are synthesized by spray drying using carbon nanotubes as additives in precursor solution, subsequently followed calcinated at high temperature in air. The structure, morphology, and texture of the as-prepared composites are characterized with XRD, Raman, BET and SEM techniques. The electrochemical properties of the as-prepared composites are investigated systematically by charge/discharge testing, cyclic voltammograms and AC impedance spectroscopy, respectively. In comparison with the pristine Li₄Ti₅O₁₂, the hole-rich Li₄Ti₅O₁₂ induced by carbon nanotubes exhibits superior electrochemical performance, especially at high rates. The obtained excellent electrochemical performances of should be attributed to the hole-rich structure of the materials, which offers more connection-area with the electrolyte, shorter diffusion-path length as well faster migration rate for both Li ions and electrons during the charge/discharge process.     

Preparation and characterization of spherical La-doped Li4Ti5O12 anode material for lithium ion batteries

The lithium secondary batteries with high power density need the electrode materials with both high specific capacity and high tap density. An “outer gel” method by TiCl₄ as the raw material has been developed to prepare spherical precursor. High tap density spherical Li₄Ti₅O₁₂ is synthesized by sintering the mixture of precursor and Li₂CO₃. La-doped Li₄Ti₅O₁₂ is also prepared by this method. X-ray diffraction, scanning electron microscopy, energy-dispersive spectrometry, tap density testing, and the determination of the electrochemical properties show that the Li₄Ti₅O₁₂ powders prepared by this method are spherical and exhibits high tap density. La³⁺ dopant improved the electrochemical performance over the pristine Li₄Ti₅O₁₂. It is tested that the tap density of the pristine and La³⁺-doped products is as high as 1.80 and 1.78 g•cm⁻³, respectively. Between 1.0 and 3.0 V versus Li, the initial discharge capacity of the La³⁺ dopant is as high as 161.5 mAh•g⁻¹ at 0.1C rate. After 50 cycles, the reversible capacity is still 135.4 mAh•g⁻¹.     

Li4Ti2.5Cr2.5O12 as anode material for lithium battery

Chromium-substituted Li₄Ti₅O₁₂ has been investigated as a negative electrode for future lithium batteries. It has been synthesized by a solid-state method followed by quenching leading to a micron-sized material. The minimum formation temperature of Li₄Ti_2.5Cr_2.5O₁₂ was found to be around 600 °C using thermogravimetric and differential thermal analysis. X-ray diffraction, scanning electron microscopy, cyclic voltammetry (CV), impedance spectroscopy, and charge–discharge cycling were used to evaluate the synthesized Li₄Ti_2.5Cr_2.5O₁₂. The particle size of the powder was around 2–4 μm. CV studies reveal a shift in the deintercalation potential by about 40 mV, i.e., from 1.54 V for Li₄Ti₅O₁₂ to 1.5 V for Li₄Ti_2.5Cr_2.5O₁₂. High-rate cyclability was exhibited by Li₄Ti_2.5Cr_2.5O₁₂ (up to 5  C) compared to the parent compound. The conduction mechanism of the compound was examined in terms of the dielectric constant and dissipation factor. The relaxation time has been evaluated and was found to be 0.07 ms. The mobility was found to be 5.133 × 10⁻⁶ cm² V⁻¹ s⁻¹.     

糠醇辅助的聚合凝胶法制备纳米Li4Ti5O12负极材料

以硝酸锂、钛酸正丁酯和糠醇为反应物,采用糠醇聚合凝胶法制备了纳米Li₄Ti₅O₁₂粉体．利用XRD、SEM和BET比表面测试对产物进行了表征,并研究了纳米Li₄Ti₅O₁₂粉体作为锂离子电池负极材料的电化学性能．在700℃或更高温度烧结时产物为纯相的尖晶石型．通过柠檬酸、聚乙烯吡咯烷酮、十六烷基三甲基溴化铵(CTAB)表面活性剂的加入能够减少产物颗粒的团聚程度,增大粉体的比表面积,提高其电化学性能．加入0.5 g CTAB、700℃烧结12 h的Li₄Ti₅O₁₂粉体展示出最高的比容量和最佳的循环性能,10 C下充电比容量高达156.7 mAh/g．     

The effects of Li2CO3 particle size on the properties of lithium titanate as anode material for lithium-ion batteries

Spinel structured Li₄Ti₅O₁₂ was synthesized by a solid-state method using TiO₂ and Li₂CO₃ as starting materials. High-energy ball milling was used to obtain the Li₂CO₃ samples with different particle size. Then, the effects of Li₂CO₃ particle size on the structure, morphology, and electrochemical performance of Li₄Ti₅O₁₂ samples were investigated in detail. The samples were characterized by TG/DTA analysis, X-ray diffraction, scanning electron microscopy and electrochemical tests, respectively. The results indicate that fine Li₂CO₃ particles will promote the interfacial reaction between Li₂CO₃ and TiO₂ in solid-state reaction. The crystallinity and particle size of Li₄Ti₅O₁₂ depend on the particle size of Li₂CO₃. Electrochemical tests show that Li₄Ti₅O₁₂ samples synthesized by fine Li₂CO₃ particles exhibit better rate capacity and cycle performance.     

Advanced electrochemical performances of Li4Ti5O12/Ag prepared by a facile synthesis route

Spinel Li₄Ti₅O₁₂ coated by highly dispersed nanosized Ag particles was synthesized via a facile and effective ultrasonic-assisted method in this paper. X-ray diffraction (XRD) results indicated that Ag was not doped into the lattice of spinel Li₄Ti₅O₁₂. The as-synthesized Li₄Ti₅O₁₂/Ag exhibited enhanced electronic conductivity and excellent electrochemical performances. Its electronic conductivity was increased about four times compared to that of the pristine Li₄Ti₅O₁₂. Even at 10 C rate, the as-synthesized Li₄Ti₅O₁₂/Ag could keep 86.5 % of the reversible capacity at 1 C rate and its reversible capacity was higher than 140 mAhg^?1 whereas those were 75.3 % and 118 mAhg^?1 for the pristine Li₄Ti₅O₁₂.     

Enhanced electrochemical performance of Cu<Subscript>2</Subscript>O-modified Li<Subscript>4</Subscript>Ti<Subscript>5</Subscript>O<Subscript>12</Subscript> anode material for lithium-ion batteries

Li₄Ti₅O₁₂/Cu₂O composite was prepared by ball milling Li₄Ti₅O₁₂ and Cu₂O with further heat treatment. The structure and electrochemical performance of the composite were investigated via X-ray diffraction, scanning electron microscopy, energy-dispersive spectroscopy, cyclic voltammetry, electrochemical impedance spectroscopy, and galvanostatic charge–discharge tests. Li₄Ti₅O₁₂/Cu₂O composite exhibited much better rate capability and capacity performance than pristine Li₄Ti₅O₁₂. The discharge capacity of the composite at 2 C rate reached up to 122.4 mAh g^?1 after 300 cycles with capacity retention of 91.3 %, which was significantly higher than that of the pristine Li₄Ti₅O₁₂ (89.6 mAh g^?1). The improvement can be ascribed to the Cu₂O modification. In addition, Cu₂O modification plays an important role in reducing the total resistance of the cell, which has been demonstrated by the electrochemical impedance spectroscopy analysis.     

1,2-丙二醇辅助溶胶凝胶法制备NASICON型Li1.3Al0.3Ti1.7(PO4)3固体电解质

通过1,2-丙二醇辅助的溶胶凝胶方法制备了具有NASICON结构的固体锂离子导体Li_1.3Al_0.3Ti_1.7(PO₄)₃,并且通过热重/差热分析、X射线衍射分析、比表面观测、电化学阻抗谱以及计时电流法等对其各方面性能进行了表征. 通过使用1,2-丙二醇辅助方法,未额外添加络合剂,也未对pH值进行调整得到均匀的溶胶前驱体,并且通过在850～950oC不同高温段烧结得到无杂相的具有NASICON结构     

Electrical and electrochemical properties of molten salt-synthesized Li4Ti5−xSnxO12 (x=0.0, 0.05 and 0.1) as anodes for Li-ion batteries

Submicron-sized polyhedral Li₄Ti_5−xSn_xO₁₂ (x=0.0, 0.05, and 0.1) materials were successfully prepared by a single-step molten salt method. The structural, morphological, transport and electrochemical properties of the Li₄Ti_5−xSn_xO₁₂ were studied. X-ray diffraction patterns showed the formation of a cubic structure with a lattice constant of 8.31 Å, and the addition of dopants follows Vegard's law. Furthermore, FT-IR spectra revealed symmetric stretching vibrations of octahedral groups of MO₆ lattice in Li₄Ti₅O₁₂. The formation of polyhedral submicron Li₄Ti_5−xSn_xO₁₂ particles was inferred from FE-SEM images, and a particle size reduction was observed for Sn-doped Li₄Ti₅O₁₂. The chemical composition of Ti, O and Sn was verified by EDAX. The DC electrical conductivity was found to increase with increasing temperature, and a maximum conductivity of 8.96×10⁻⁶ S cm⁻¹ was observed at 200 °C for Li₄Ti₅O₁₂. The galvanostatic charge–discharge behavior indicates that the Sn-doped Li₄Ti₅O₁₂ could be used as an anode for Li-ion batteries due to its enhanced electrochemical properties.     

Evolution of crystal structure and electrochemical performance of layered Li<Subscript>1.20</Subscript>Ti<Subscript>0.44</Subscript>Cr<Subscript>0.36</Subscript>O<Subscript>2</Subscript>/C cathode materials with cycling

Carbon-coated layered Li_1.20Ti_0.44Cr_0.36O₂/C and pristine Li_1.20Ti_0.44Cr_0.36O₂ cathode materials have been synthesized through a sol–gel method followed by high-temperature calcination. Their electrochemical performances have been evaluated, which indicate that the Li_1.20Ti_0.44Cr_0.36O₂/C exhibits much higher cyclic stability and capacity than the pristine one. The initial delithiation capacity of the Li_1.20Ti_0.44Cr_0.36O₂/C can reach 217.1 mAh g^?1. The reversible capacity retention is 94 % after 100 cycles at current density of 23 mA g^?1. Ex situ X-ray diffraction and electrochemistry impedance spectroscopy coupled with impedance fitting have been employed to reveal evolution of the crystal structure and the electrochemical kinetics of the Li_1.20Ti_0.44Cr_0.36O₂/C with delithiation/lithiation cycling. The results indicate that the cation layers of the Li_1.20Ti_0.44Cr_0.36O₂/C experience order to disorder transition. The abrupt delithiation capacity fading and potential drop after the initial cycle are resulted from the order to disorder transition accompanying with steep increase of the charge transfer resistance and decrease of the exchange current density and the Li-ion diffusion coefficient simultaneously.     

A new composite material Li<Subscript>4</Subscript>Ti<Subscript>5</Subscript>O<Subscript>12</Subscript>–SnO<Subscript>2</Subscript> for lithium-ion batteries

A new Li₄Ti₅O₁₂–SnO₂ composite anode material for lithium-ion batteries has been prepared by loading SnO₂ on Li₄Ti₅O₁₂ to obtain composite material with improved electrochemical performance relative to Li₄Ti₅O₁₂ and SnO₂. The composite material was characterized by X-ray diffraction and scanning electron microscopy. The results indicated that SnO₂ particles have encapsulated on the surface of the Li₄Ti₅O₁₂ uniformly and tightly. Electrochemical results indicated that the Li₄Ti₅O₁₂–SnO₂ composite material increases the reversible capacity of Li₄Ti₅O₁₂ and has good cycling reliability. At a current rate of 0.5 mA/cm², the material delivered a discharge capacity of 236 mAh/g after 16 cycles. It suggests the existence of synergistic interaction between Li₄Ti₅O₁₂ and SnO₂ and that the capacity of the composite is not a simple weighted sum of the capacities of the individual components. In the composite material, SnO₂ can act as a bridge between the spinel particles to reduce the interparticle resistance and as a good material for the Li intercalation/deintercalation. Thus, electrochemical performance of the Li₄Ti₅O₁₂ spinel can be improved by the surface modification with SnO₂, and the stability of Li₄Ti₅O₁₂ also serves to buffer the internal stress caused by the volume changes in lithium insertion and extraction reactions.     

Influence of post-calcination treatment on the spinel lithium titanium oxide anode material for lithium ion batteries

The influence of post-calcination treatment on spinel Li₄Ti₅O₁₂ anode material is extensively studied combining with a ball-milling-assisted rheological phase reaction method. The post-calcinated Li₄Ti₅O₁₂ shows a well distribution with expanded gaps between particles, which are beneficial for lithium ion mobility. Electrochemical results exhibit that the post-calcinated Li₄Ti₅O₁₂ delivers an improved specific capacity and rate capability. A high discharge capacity of 172.9 mAh g^?1 and a reversible charge capacity of 171.1 mAh g^?1 can be achieved at 1 C rate, which are very close to its theoretical capacity (175 mAh g^?1). Even at the rate of 20 C, the post-calcinated Li₄Ti₅O₁₂ still delivers a quite high charge capacity of 124.5 mAh g^?1 after 50 cycles, which is much improved over that (43.9 mAh g^?1) of the pure Li₄Ti₅O₁₂ without post-calcination treatment. This excellent electrochemical performance should be ascribed to the post-calcination process, which can greatly improve the lithium ion diffusion coefficient and further enhance the electrochemical kinetics significantly.     

Synthesis of Li<Subscript>4</Subscript>Ti<Subscript>5</Subscript>O<Subscript>12</Subscript>-reduced graphene oxide composite and its application for hybrid supercapacitors

We describe in this paper the synthesis and the characterization of Li₄Ti₅O₁₂-reduced graphene oxide (LTO-RGO) composite and demonstrate their use as hybrid supercapacitor, which is consist of an LTO negative electrode and activate carbon (AC) positive electrode. The LTO-RGO composites were synthesized using a simple, one-step process, in which lithium sources and titanium sources were dissolved in a graphene oxide (GO) suspension and then thermal treated in N₂. The lithium-ion battery with LTO-RGO composite anode electrode revealed higher discharge capacity (167 mAh g^?1 at 0.2 C) and better capacity retention (67%) than the one with pure LTO. Meanwhile, compared with the AC//LTO supercapacitor, the AC//LTO-RGO hybrid supercapacitor exhibits higher energy density and power density. Results show that the LTO-RGO composite is a very promising anode material for hybrid supercapacitor.     

Enhanced high-rate performance of sub-micro Li4Ti4.95Zn0.05O12 as anode material for lithium-ion batteries

Zn-doped Li₄Ti₅O₁₂ was prepared by a ball milling-assisted solid-state method, and the characters were determined by X-ray diffraction, Raman spectroscopy, scanning electron microscopy, cyclic voltammetry, and galvanostatic charge–discharge testing. The results show that Li₄Ti_5?x Zn _x O₁₂ (x?=?0, 0.05) exhibits the pure phase structure, and Zn doping does not change the electrochemical reaction process and basic spinel structure of Li₄Ti₅O₁₂. The particle size of both samples is about 300–500 nm. The prepared Li₄Ti_4.95Zn_0.05O₁₂ presents an excellent rate capability and capacity retention. At the charge–discharge rate of 1C, the initial discharge capacity of Li₄Ti_4.95Zn_0.05O₁₂ is 268 mAh g^?1. After 90 cycles at 5C, the discharge capacity of Li₄Ti_4.95Zn_0.05O₁₂ is obviously higher than that of Li₄Ti₅O₁₂. The excellent electrochemical performance of the Li₄Ti_4.95Zn_0.05O₁₂ electrode could be attributed to the improvement of reversibility by doping zinc and the sub-micro particle size.     

Research progress on the low-temperature electrochemical performance of Li<Subscript>4</Subscript>Ti<Subscript>5</Subscript>O<Subscript>12</Subscript> anode material

Li₄Ti₅O₁₂ is regarded as the ideal anode material for its stable structure, high charge/discharge platform, and safety performance. But low ionic and electronic conductivity of the Li₄Ti₅O₁₂ anode material under the condition of low temperature greatly limit its application in practical production. In this paper, some modified methods for improving the low-temperature electrochemical performance of Li₄Ti₅O₁₂ anode material were summarized. Meanwhile, we explored its influence mechanisms at low temperature, one is, with the subtle changes of lattice parameters and oxygen atom fraction coordinates of Li₄Ti₅O₁₂ at low temperature, the changes of the bond length influence the structural stability of Li₄Ti₅O₁₂ and the diffusion path of lithium ions; the other reason is that the charge transfer resistance increases obviously and the lithium ion diffusion coefficient reduces under low temperature. Finally, the research directions for improving the low-temperature electrochemical performance were proposed.     

Enhanced rate performance of lithium titanium oxide anode material by bromine doping

Br-doped lithium titanium oxide (Li₄Ti₅O₁₂) particles in the form of Li₄Ti₅Br _x O_12-x (x?=?0, 0.1, 0.2, 0.3, 0.4) are synthesized via a simple liquid deposition reaction, followed by a high-temperature treatment. The effects of bromine (Br) doping on the structures and electrochemical properties of Li₄Ti₅O₁₂ are extensively studied. It is found that Br atoms can enter the lattice structure and enlarge the lattice parameters of Li₄Ti₅O₁₂. Although Br doping has not changed the phase composition, obvious effects on the particle’s morphology and size have been observed. Electrochemical test results indicate that the rate capability of Li₄Ti₅O₁₂ has been evidently improved by Br doping at an appropriate concentration. The as-synthesized Li₄Ti₅O_11.8Br_0.2 electrode presents much higher discharge capacity and better cycle stability than that of the other electrodes. The greatly enhanced electrochemical performance of Li₄Ti₅O_11.8Br_0.2 may be attributed to the improved dispersion of nanoparticles and increased electrical conductivity.