Photo‐oxidation of poly(2,6‐dimethyl‐1,4‐phenylene oxide): A reinvestigation

Reinvestigation of poly(2,6‐dimethyl‐1,4‐phenylene oxide) photodegradation at wavelengths > 290 nm shows that both methyl groups and aromatic rings are sites of oxidation with their relative rates dependent on exposure conditions, based on infrared spectroscopy. The methyl group loss is linear with exposure and apparently proceeds by direct abstraction of a benzylic hydrogen by oxygen. The aromatic ring loss and carbonyl growth in the IR spectra appear to be auto‐accelerating and seem to proceed by electron transfer to oxygen, either sensitized or through a direct reaction with oxygen, and recombination of the polymer radical cation and superoxide to result in oxygen addition to the ring. Molecular weight loss in solution occurs to a significant degree only in the presence of oxygen, even in the presence of a hydrogen‐donating solvent, indicating that aryl ether photolysis is not a major pathway. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 2318–2331     

Fluorescent oligo(N‐phenylmaleimide)s via aerobic radical telomerization initiated by benzylic hydrocarbons: Catalytic effect of CoII/N‐hydroxyphthalimide pair

Radical oligomerization of N‐phenylmaleimide (NPMI) was performed in benzylic hydrocarbons as the solvent. The thermally induced oligomerization occurred only above 130 °C, with the initiation attributed to autoxidation of benzylic hydrocarbons as well as formation and dissociation of charge‐transfer complexes between benzylic hydrocarbons and maleimides. The end‐group analysis on oligo(N‐ethylmaleimide) prepared under similar conditions confirmed that the chain transfer to benzylic hydrocarbons was the primary fashion in forming oligomeric chains, and radical telomerization underlaid the oligomerization with benzylic hydrocarbons as both the solvent, the initiator and the telogen. Co^II/N‐hydroxyphthalimide (NHPI) pairs could catalyze the telomerization at 110 °C. In such a catalytic process, Co^II‐based oxidative complexes oxidized benzylic hydrocarbons and NHPI into benzylic radicals and phthalimide N‐oxyl (PINO), and benzylic hydrocarbons underwent hydrogen atom transfer (HAT) to PINO. Oligo(NPMI)s were formed via HAT with benzylic hydrocarbons and NHPI. These oligo(NPMI)s exhibited fluorescent properties with excitation at 270–350 nm and 400–550 nm and emission at 530–750 nm. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 3846–3857     

Synthesis of new thermosetting poly(2,6‐dimethyl‐1,4‐phenylene oxide)s containing epoxide pendant groups

A new class of thermosetting poly(2,6‐dimethyl‐1,4‐phenylene oxide)s containing pendant epoxide groups were synthesized and characterized. These new epoxy polymers were prepared through the bromination of poly(2,6‐dimethyl‐1,4‐phenylene oxide) in halogenated aromatic hydrocarbons followed by a Wittig reaction to yield vinyl‐substituted polymer derivatives. The treatment of the vinyl‐substituted polymers with m‐chloroperbenzoic acid led to the formation of epoxidized poly(2,6‐dimethyl‐1,4‐phenylene oxide) with variable pendant ratios, and the structures and properties were studied with nuclear magnetic resonance spectroscopy, Fourier transform infrared spectroscopy, differential scanning calorimetry, thermogravimetric analysis, and gel permeation chromatography. The ratios of pendant functional groups were tailored for the polymer properties, and the results showed that the glass‐transition temperatures increased as the benzylic protons were replaced by bromo‐, vinyl‐, or epoxide‐functional groups, whereas the thermal stability decreased in comparison with the original polymer. Within a molar fraction of 20–50%, the degree of functionalization had little effect on the glass‐transition temperature; however, it correlated inversely with the thermal stability of each functionalized polymer. The thermal curing behavior of the epoxide‐functionalized polymer was enhanced by the increment of the pendant functionality, which resulted in a significant increase in the glass‐transition temperature as well as the thermal stability after the curing reaction. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 5875–5886, 2006     

Asymmetric anionic polymerizations of 7‐(o‐substituted phenyl)‐2,6‐dimethyl‐1,4‐benzoquinone methides: Electrostatic interaction and steric,inductive, and resonance effects of the ortho‐substituent on the optical activity

7‐(o‐Substituted phenyl)‐2,6‐dimethyl‐1,4‐benzoquinone methides which have an electron‐donating methoxy‐(o‐OMe, 2a ) and methyl‐ (o‐Me, 2b ) substituents or an electron‐withdrawing cyano‐ (o‐CN, 2c ) and trifluoromethyl‐ (o‐CF₃, 2d ) substituents at the ortho‐position of the aromatic ring and 7‐(m‐substituted phenyl)‐2,6‐dimethyl‐1,4‐benzoquinone methide with an electron‐withdrawing trifluoromethyl‐ (m‐CF₃, 2e ) substituent at the meta‐position of the aromatic ring were synthesized, and their asymmetric anionic polymerizations using the complex of lithium 4‐isopropylphenoxide with (?)‐sparteine were carried out in toluene at 0 °C. The polymers with negative optical activity were obtained for all of five monomers, and their specific rotation values largely changed depending upon the substituents of the monomers. On the basis of the comparison of various substituents effects, it was found that the specific rotation of obtained polymers is significantly affected by the electronic effects such as inductive and resonance effects rather than the steric and electrostatic effects of the substituent. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55 , 1048–1058     

Pd (II)‐catalyzed vinyl addition polymerization of novel functionalized norbornene bearing dimethyl carboxylate groups

Three novel functionalized polynorbornenes (PNB) with pendant dimethyl carboxylate group (carboxylates—acetate, propionate, and butyrate) are synthesized as a vinyl‐type with a palladium (II) catalyst in high yield. The effects of size of substitutents, molar ratio of monomer to catalyst, solvent polarity, reaction time, and temperature on the polymerization of exo‐norbornene dimethyl propionate were systematically investigated. The low molar ratio and temperature, as well as high polarity of solvent, and long reaction time, are favorable for the enhancement of the monomer conversion, especially, the solvent have an obvious effect on the catalyst activity. The resulting poly(cis‐norbornene‐exo‐2,3‐dimethyl carboxylates) (PNB‐dimethyl carboxylates) show good solubility in common organic solvent and high thermal stability up to 360 °C. The glass transition temperature was detected by DMA at 331, 324, and 318 °C for acetate, propionate, and butyrate, respectively. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 3391–3399, 2007     

Aromatic poly(1,3,4‐oxadiazole)s and poly(amide‐1,3,4‐oxadiazole)s containing ether sulfone linkages

Polyhydrazides and poly(amide‐hydrazide)s were prepared from two ether‐sulfone‐dicarboxylic acids, 4,4′‐[sulfonylbis(1,4‐phenylene)dioxy]dibenzoic acid and 4,4′‐[sulfonylbis(2,6‐dimethyl‐1,4‐phenylene)dioxy]dibenzoic acid, or their diacyl chlorides with terephthalic dihydrazide, isophthalic dihydrazide, and p‐aminobenzhydrazide via a phosphorylation reaction or a low‐temperature solution polycondensation. All the hydrazide polymers were found to be amorphous according to X‐ray diffraction analysis. They were readily soluble in polar organic solvents such as N‐methyl‐2‐pyrrolidone and N,N‐dimethylacetamide and could afford colorless, flexible, and tough films with good mechanical strengths via solvent casting. These hydrazide polymers exhibited glass‐transition temperatures of 149–207 °C and could be thermally cyclodehydrated into the corresponding oxadiazole polymers in the solid state at elevated temperatures. Although the oxadiazole polymers showed a significantly decreased solubility with respect to their hydrazide prepolymers, some oxadiazole polymers were still organosoluble. The thermally converted oxadiazole polymers had glass‐transition temperatures of 217–255 °C and softening temperatures of 215–268 °C and did not show significant weight loss before 400 °C in nitrogen or air. For a comparative study, related sulfonyl polymers without the ether groups were also synthesized from 4,4′‐sulfonyldibenzoic acid and the hydrazide monomers by the same synthetic routes. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 2271–2286, 2001     

Synthesis and properties of alternating copolyamide‐imides based on 2,6‐bis(4‐aminophenoxy)naphthalene and comparison with its related isomeric polymers

A series of novel polyamide‐imides III containing 2,6‐bis(phenoxy)naphthalene units were synthesized by 2,6‐bis(4‐aminophenoxy)naphthalene and various bis(trimellitimide)s in N‐methyl‐2‐pyrrolidone (NMP) using triphenyl phosphite and pyridine as condensing agents through direct polycondensation. The polymers were obtained in quantitative yield with inherent viscosities up to 1.53 dL/g. Most of the polymers showed good solubility in NMP, N,N‐dimethylacetamide, N,N‐dimethylformamide, and dimethyl sulfoxide and could be solution‐cast into transparent, flexible, and tough films. The films had tensile strengths of 84–111 MPa, elongations at break of 8–33%, and initial moduli of 2.2–2.8 GPa. Wide‐angle X‐ray diffraction revealed that most polymers III were amorphous. The glass‐transition temperatures of some of the polymers could be determined by differential scanning calorimetry traces, recorded at 247–290 °C. The polyamide‐imides exhibited excellent thermal stabilities and had 10% weight loss at temperatures in the range of 501–575 °C under nitrogen atmosphere. They left more than 57% residue even at 800 °C in nitrogen. A comparative study of some corresponding polyamide‐imides is also presented. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 2591–2601, 2001     

Synthesis and crystallization behavior of rigid copolyesters with biphenyl‐4,4′‐dicarboxylate and 2,6‐naphthalenedicarboxylate in the main chain

Structurally rigid copolyester thermoplastics were synthesized from 1,4‐cyclohexanedimethanol and the diesters dimethyl biphenyl‐4,4′‐dicarboxylate and dimethyl 2,6‐naphthalenedicarboxylate (DMN) via conventional melt transesterification. Conventional differential scanning calorimetry (CDSC) showed all compositions to exhibit multiple endotherms upon heating. Wide‐angle X‐ray diffraction analysis showed copolyester compositions to exhibit the crystalline structure of either the homopolyester Poly(1,4‐cyclohexylenedimethylene 2,6‐naphthalate) (PCN) or the homopolyester Poly(1,4‐cyclohexylenedimethylene 4,4′‐bibenzoate) (PCB), but not both simultaneously. Further thermal analysis using CDSC and fast DSC investigated the origin of the multiple endotherm behavior. While three endotherms are observed for low heating rates, the upper two endotherms appear to merge at heating rates about 1–5 °C s^?1 and a single endotherm remains above heating rates about 10–50 °C s^?1. While the behavior of the upper two endotherms is undeniably consistent with the mechanism of melting–recrystallization–remelting (MRR), we suggest that the low endotherm is likely associated with the melting of constrained secondary crystals, although MRR effects cannot be ruled out. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 973–980     

Synthesis of photosensitive and thermosetting poly(phenylene ether) based on poly[2,6‐di(3‐methyl‐2‐butenyl)phenol‐co‐2,6‐dimethyl‐phenol] and a photoacid generator

A chemically amplified photosensitive and thermosetting polymer based on poly[2,6‐di(3‐methyl‐2‐butenyl)phenol (15 mol %)‐co‐2,6‐dimethylphenol (85 mol %)] ( 3c ) and a photoacid generator [(5‐propylsulfonyloxyimino‐5H‐thiophen‐2‐ylidene)‐(2‐methylphenyl)acetonitrile] was developed. Poly[2,6‐bis(3‐methyl‐2‐butenyl)phenol]‐co‐2,6‐dimethylphenol)] ( 3 ) with high molecular weights (number‐average molecular weight ～ 24,000) was prepared by the oxidative coupling copolymerization of 2,6‐di(3‐methyl‐2‐butenyl)phenol with 2,6‐dimethylphenol in the presence of copper(I) chloride and pyridine as the catalyst under a stream of oxygen. The structures of 3 were characterized with IR, ¹H NMR, and ¹³C NMR spectroscopy. 3 was crosslinked by a thermal treatment at 300 °C for 1 h under N₂. The 5% weight loss temperatures and glass‐transition temperatures of the cured copolymers reached around 420 °C in nitrogen and 300 °C, respectively. The average refractive index of the cured copolymer ( 3c ) film was 1.5452, from which the dielectric constant at 1 MHz was estimated to be 2.6. The resist showed a sensitivity of 35 mJ cm^?2 and a contrast of 1.6 when it was exposed to 436‐nm light, postexposure‐baked at 145 °C for 5 min, and developed with toluene at 25 °C. A fine negative image featuring 8‐μm line‐and‐space patterns was obtained on a film exposed to 100 mJ cm^?2 with 436‐nm light in the contact‐printed mode. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 149–156, 2005     

Synthesis and characterization of novel polyamide‐imides containing noncoplanar 2,2′‐dimethyl‐4,4′‐biphenylene unit

A new diimide‐dicarboxylic acid, 2,2′‐dimethyl‐4,4′‐bis(4‐trimellitimidophenoxy)biphenyl (DBTPB), containing a noncoplanar 2,2′‐dimethyl‐4,4′‐biphenylene unit was synthesized by the condensation reaction of 2,2′‐dimethyl‐4,4′‐bis(4‐minophenoxy)biphenyl (DBAPB) with trimellitic anhydride in glacial acetic acid. A series of new polyamide‐imides were prepared by direct polycondensation of DBAPB and various aromatic diamines in N‐methyl‐2‐pyrrolidinone (NMP), using triphenyl phosphite and pyridine as condensing agents. The polymers were produced with high yield and moderate to high inherent viscosities of 0.86–1.33 dL · g⁻¹. Wide‐angle X‐ray diffractograms revealed that the polymers were amorphous. Most of the polymers exhibited good solubility and could be readily dissolved in various solvents such as NMP, N,N‐dimethylacetamide (DMAc), N,N‐dimethylformamide (DMF), dimethyl sulfoxide, pyridine, cyclohexanone, and tetrahydrofuran. These polyamide‐imides had glass‐transition temperatures between 224–302 °C and 10% weight loss temperatures in the range of 501–563 °C in nitrogen atmosphere. The tough polymer films, obtained by casting from DMAc solution, had a tensile strength range of 93–115 MPa and a tensile modulus range of 2.0–2.3 GPa. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 63–70, 2001     

End‐group modification of poly(2,6‐dimethyl‐1,4‐phenylene ether) and in situ synthesis of poly(2,6‐dimethyl‐1,4‐phenylene ether)‐b‐poly(ethylene terephthalate) block copolymer

The preparation of poly(2,6‐dimethyl‐1,4‐phenylene ether)‐b‐poly(ethylene terephthalate) block copolymer was performed by the reaction of the 2‐hydroxyethyl modified poly(2,6‐dimethyl‐1,4‐phenylene ether) (PPE‐EtOH) with poly(ethylene terephthalate) (PET) by an in situ process, during the synthesis of the polyester. The yield of the reaction of the 2‐hydroxyethyl functionalized PPE‐EtOH with PET was close to 100%. A significant proportion of the PET‐b‐PPE‐EtOH block copolymer was found to have short PET block. Nevertheless, the copolymer structured in the shape of micelles (20 nm diameter) and very small domains with 50–200 nm diameter, whereas unmodified PPE formed much larger domains (1.5 μm) containing copolymer. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 3985–3991, 2008     

Radical heterogeneous polymerization behavior of N‐methyl‐α‐fluoroacrylamide in benzene

The polymerization of N‐methyl‐α‐fluoroacrylamide (NMFAm) initiated with dimethyl 2,2′‐azobisisobutyrate (MAIB) in benzene was studied kinetically and with electron spin resonance. The polymerization proceeded heterogeneously with the highly efficient formation of long‐lived poly(NMFAm) radicals. The overall activation energy of the polymerization was 111 kJ/mol. The polymerization rate (R_p) at 50 °C is given by R_p = k[MAIB]^0.75±0.05 [NMFAm]^0.44±0.05. The concentration of the long‐lived polymer radical increased linearly with time. The formation rate (R_p?) of the long‐lived polymer radical at 50 °C is expressed by R_p? = k[MAIB]^1.0±0.1 [NMFAm]^0±0.1. The overall activation energy of the long‐lived radical formation was 128 kJ/mol, which agreed with the energy of initiation (129 kJ/mol), which was separately estimated. A comparison of R_p? with the initiation rate led to the conclusion that 1‐methoxycarbonyl‐1‐methylethyl radicals (primary radicals from MAIB), escaping from the solvent cage, were quantitatively converted into the long‐lived poly(NMFAm) radicals. Thus, this polymerization involves completely unimolecular termination due to polymer radical occlusion. ¹H NMR‐determined tacticities of resulting poly(NMFAm) were estimated to be rr = 0.34, mr = 0.48, and mm = 0.18. The copolymerization of NMFAm(M₁) and St(M₂) with MAIB at 50 °C in benzene gave monomer reactivity ratios of r₁ = 0.61 and r₂ = 1.79. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 2196–2205, 2001     

Low dielectric thermoset. II. Synthesis and properties of novel 2,6‐dimethyl phenol–dipentene epoxy

A 2,6‐dimethyl phenol–dipentene adduct was synthesized from dipentene (DP) and 2,6‐dimethyl phenol, and then a 2,6‐dimethyl phenol–DP epoxy was synthesized from the reaction of the resultant 2,6‐dimethyl phenol–DP adduct and epichlorohydrin. The proposed structures were confirmed by Fourier transform infrared, elemental analysis, mass spectra, NMR spectra, and epoxy equivalent weight titration. The synthesized 2,6‐dimethyl phenol–DP adduct was cured with 4,4‐diamino diphenyl methane, phenol novolac, 4,4‐diamino diphenyl sulfone, and 4,4‐diamino diphenyl ether. The thermal properties of the cured epoxy resins were studied with differential scanning calorimetry, dynamic mechanical analysis, dielectric analysis, and thermogravimetric analysis. These data were compared with those for the bisphenol A epoxy system. The cured 2,6‐dimethyl phenol–DP epoxy exhibited a lower dielectric constant (ca. 3.1), a lower dissipation factor (ca. 0.065), a lower modulus, lower thermal stability (5% degradation temperature = 366–424 °C), and lower moisture absorption (1.21–2.18%) than the bisphenol A system but a higher glass‐transition temperature (ca. 173–222 °C) than that of bisphenol A system. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 4084–4097, 2002     

Scalable ambient synthesis of water‐soluble poly(β‐hydroxythio‐ether)s

Proton transfer polymerization through thiol‐epoxy “click” reaction between commercially available and hydrophilic di‐thiol and di‐epoxide monomers is carried out under ambient conditions to furnish water‐soluble polymers. The hydrophilicity of monomers permitted use of aqueous tetrahydrofuran as the reaction medium. A high polarity of this solvent system in turn allowed for using a mild catalyst such as triethylamine for a successful polymerization process. The overall simplicity of the system translated into a simple mixing of monomers and isolation of the reactive polymers in an effortless manner and on any scale required. The structure of the resulting polymers and the extent of di‐sulfide defects are studied with the help of 13C‐ and ¹H‐NMR spectroscopy. Finally, reactivity of the synthesized polymers is examined through post‐polymerization modification reaction at the backbone sulfur atoms through oxidation reaction. The practicality, modularity, further functionalizability, and water solubility aspects of the described family of new poly(β‐hydroxythio‐ether)s is anticipated to accelerate investigations into their potential utility in bio‐relevant applications. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 3381–3386     

Effect of ortho‐methylation on a bis(4‐cyanatocumyl)benezene low‐dielectric resin

A synthesis procedure for and characterization of a tetra‐ortho‐methyl substituted three‐ringed cyanate ester monomer, 4,4′‐[1,3‐phenylenebis(1‐methylethylidene)]bis[2,6‐dimethyl]phenylcyanato, and the corresponding cured resin are described with comparative characterization of the resin analogue without the ortho‐methyl substitutents. The othro‐methylation lowered the dielectric from 2.64 to 2.59 at 1 GHz and from 2.64 to 2.48 GHz at 15 GHz, whereas the tan δ was not significantly affected. Other physical properties also affected included a 40 °C decrease in the glass‐transition temperature, an increase in the thermal‐expansion coefficients, and a reduction in thermogravimetric stability. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 60–67, 2003     

Synthesis and properties of aromatic polyimides derived from 2,2,′3,3′‐biphenyltetracarboxylic dianhydride

2,2,′3,3′‐Biphenyltetracarboxylic dianhydride (2,2,′3,3′‐BPDA) was prepared by a coupling reaction of dimethyl 3‐iodophthalate. The X‐ray single‐crystal structure determination showed that this dianhydride had a bent and noncopolanar structure, presenting a striking contrast to its isomer, 3,3,′4,4′‐BPDA. This dianhydride was reacted with aromatic diamines in a polar aprotic solvent such as N,N‐dimethylacetamide (DMAc) to form polyamic acid intermediates, which imidized chemically to polyimides with inherent viscosities of 0.34–0.55 dL/g, depending on the diamine used. The polyimides from 2,2,′3,3′‐BPDA exhibited a good solubility and were dissolved in polar aprotic solvents and polychlorocarbons. These polyimides have high glass transition temperatures above 283°C. Thermogravimetric analyses indicated that these polyimides were fairly stable up to 500°C, and the 5% weight loss temperatures were recorded in the range of 534–583°C in nitrogen atmosphere and 537–561°C in air atmosphere. All polyimides were amorphous according to X‐ray determination. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 1425–1433, 1999     

Oxidative polymerization of 2,6‐dimethylphenol to form poly(2,6‐dimethyl‐1,4‐phenylene oxide) in water through one water‐soluble copper(II) complex of a zwitterionic calix[4]arene

In the presence of excess NaOH, reaction of Cu(OAc)₂·H₂O with equimolar ammonium calix[4]arene [H₄L]I₄ ( 1 , H₄L = [5,11,17,23‐tetrakis(trimethylammonium)‐25,26,27,28‐tetrahydroxycalix[4]arene]) resulted in the formation of a mononuclear cationic Cu(II) complex [Cu(II)L(H₂O)]I₂ ( 2 ) in 43% yield. Complex 2 was characterized by elemental analysis, infrared (IR), and single crystal X‐ray diffraction. The Cu(II) atom in 2 is coordinated by four oxygen atoms of one L^4? ligand and one O atom from one water molecule, forming a square pyramidal geometry. Complex 2 exhibited high catalytic activity in the oxidative polymerization of 2,6‐dimethylphenol using O₂ as oxidizing agent in water under mild conditions. The selective polymerization produced poly(2,6‐dimethyl‐1,4‐phenylene oxide) in high yields with almost no diphenoquinone. The influence of the polymerization temperature, the time interval, the molar ratio of 2,6‐dimethylphenol/ 2 , the concentrations of sodium hydroxide, and sodium n‐dodecyl sulfate were examined. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Catalytic oxidative reactions of organic compounds by nitrogen‐containing copper complexes

The dimeric copper(II) complex di‐µ‐chloro‐bis[chloro(di‐3,5‐dimethylpyrazole)copper(II)] (A) in the presence of co‐oxidant hydrogen peroxide acts as a catalyst for the oxidation of benzylic alcohols to give the corresponding aldehydes. In the presence of hydrogen peroxide it also catalyses the oxidation reaction of 2,6‐dimethylphenol to 4,4′‐dihydroxy‐3,5,3′,5′‐tetramethylbiphenyl. The oxidative reactions by bis‐pyridinium tetrachlorocopper(II) (B) in the presence of hydrogen peroxide were compared for similar catalytic reactions of A, and it is observed that B can catalyse the oxidation of aromatic diols, 2,6‐dimethylphenol and thiophenol, but is not suitable for oxidation of benzylic alcohols. Bis‐(N‐phenyl‐3,5‐dimethylpyrazole)copper(II) nitrate monohydrate (C) has a suitable redox potential for one‐electron oxidation. It can oxidize ferrocene to the ferricinium cation, and it can liberate bromine from tetra‐alkylammonium bromides. The complex is catalytically effective for the oxidation of different aromatic and aliphatic aldehydes to the corresponding carboxylic acids. The compound is also effective in transforming benzylic amine to benzylalcohol and benzaldehyde. It can also oxidize diphenylmethane to give benzophenone and diphenylmethanol. It is observed that in each of these complexes a quasi‐reversible Cu(I)–Cu(II) species is present and facilitates the single‐electron oxidation process. Copyright © 2004 John Wiley & Sons, Ltd.     

Synthesis and characterization of fluorinated poly(amide imide)s derived from 1,4‐bis(2′‐trifluoromethyl‐4′‐trimellitimidophenoxy)benzene and aromatic diamines

A series of fluorinated poly(amide imide)s were prepared from 1,4‐bis(2′‐trifluoromethyl‐4′‐trimellitimidophenoxy)benzene and various aromatic diamines [3,3′,5,5′‐tetramethyl‐4,4′‐diaminediphenylmethane, α,α‐bis(4‐amino‐3,5‐dimethyl phenyl)‐3′‐trifluoromethylphenylmethane, 1,4‐bis(4′‐amino‐2′‐trifluoromethylphenoxy)benzene, 4‐(3′‐trifluoromethylphenyl)‐2,6‐bis(3′‐aminophenyl)pyridine, and 1,1‐bis(4′‐aminophenyl)‐1‐(3′‐trifluoromethylphenyl)‐2,2,2‐trifluoroethane]. The fluorinated poly(amide imide)s, prepared by a one‐step polycondensation procedure, had good solubility both in strong aprotic solvents, such as N‐methyl‐2‐pyrrolidinone, dimethylacetamide, dimethylformamide, dimethyl sulfoxide, and cyclopentanone, and in common organic solvents, such as tetrahydrofuran and m‐cresol. Strong and flexible polymer films with tensile strengths of 84–99 MPa and ultimate elongation values of 6–9% were prepared by the casting of polymer solutions onto glass substrates, followed by thermal baking. The poly(amide imide) films exhibited high thermal stability, with glass‐transition temperatures of 257–266 °C and initial thermal decomposition temperatures of greater than 540 °C. The polymer films also had good dielectric properties, with dielectric constants of 3.26–3.52 and dissipation factors of 3.0–7.7 × 10^?3, and acceptable electrical insulating properties. The balance of excellent solubility and thermal stability associated with good mechanical and electrical properties made the poly(amide imide)s potential candidates for practical applications in the microelectronics industry and other related fields. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 1831–1840, 2003     

Negative‐type photosensitive poly(phenylene ether) based on poly(2,6‐dimethyl‐1,4‐phenylene ether), a crosslinker,and a photoacid generator

A negative‐type photosensitive poly(phenylene ether) (PSPPE) based on poly(2,6‐dimethyl‐1,4‐phenylene ether) (PPE), a novel crosslinker 4,4′‐methylene‐bis [2,6‐bis(methoxymethyl)phenol] (MBMP) having good compatibility with PPE, and diphenylidonium 9,10‐dimethoxy anthracene‐2‐sulfonate (DIAS) as a photoacid generator (PAG) has been developed. This resist consisting of PPE (73 wt %), MBMP (20 wt %) and DIAS (7 wt %) showed a high sensitivity (D_0.5) of 58 mJ/cm² and a contrast (γ_0.5) of 9.5 when it was exposed to i‐line (365 nm wavelength light), postexposure baked at 145 °C for 10 min, and developed with toluene at 25 °C. A fine negative image featuring 6 μm line‐and‐space pattern was obtained on the film exposed to 300 mJ/cm² of i‐line by a contact‐printed mode. The resulting polymer film cured at 300 °C for 1 h under nitrogen had a low dielectric constant (ε = 2.46) comparable to that of PPE and a higher T_g than that of PPE. In addition, the cured PSPPE film was pretty low water absorption (<0.05%) as same as PPE. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 4949–4958, 2008