Miscibility and surface segregation in PVC/polyester blends—The influence of chain architecture and composition

Four poly(butylene adipate) (PBA) polyesters, the structure ranging from linear to highly branched, were synthesized and solution casted with poly(vinyl chloride) (PVC) in 20 or 40 wt % concentrations to evaluate the influence of polyester chain architecture on miscibility, surface segregation, and mechanical properties. The miscibility of PVC and polyesters is based on specific interactions between the carbonyl group in the polyester and PVC. These interactions cause a shift in the carbonyl absorption band in the FTIR spectra. The shifting of the carbonyl absorption band was more significant for all the 40 wt % blends compared with the blends containing 20 wt % of the same polyester. In the 20 wt % blends surface segregation and enrichment of polyester at the blend surface increased as a function of branching. However, all the films containing 40 wt % of polyester had similar surface composition. This is explained by better miscibility and stronger intermolecular interactions in the 40 wt % blends, which counteract the effect of branching on the surface segregation. High degree of branching resulted in poor miscibility with PVC and poor mechanical properties. A linear or slightly branched polyester structure, however, resulted in good miscibility and desirable blend properties. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1552–1563, 2007     

Analyse de la relations structure-proprietes des melanges PVC-PMMA

Analysis of Structure-Properties Relationship of PVC-PMMA Blends. This paper presents a study of the structure-properties relationship of PVC-PMMA blends. For that purpose, blends of variable compositions from 0 to 100 wt % were prepared. Their physico-chemical characterization was carried out by differential scanning calorimetric analysis (DSC) and Fourier Transform Infrared spectroscopy (FTIR). The analysis of thermograms showed polymer miscibility up to 60 wt % PMMA. This miscibility is due to a specific interaction of hydrogen bonding type between carbonyl groups (C+O) of PMMA and hydrogen from (CHCl) groups of PVC. The two-band deconvolution showed an increase in associated groups percentage in the domain of miscibility. The variation of mechanical properties such as tensile behaviour, hardness and impact resistance was investigated for all blend compositions. The effect of a plasticizer on the same properties was considered. The obtained results show that a range of properties can be generated according to the blend compositions.     

Binary blends based on poly(vinyl chloride) and multi-block copolymers containing poly(ϵ-caprolactone) and poly(ethylene glycol) segments

Binary blends based on poly(vinyl chloride) (PVC) were prepared both by casting from tetrahydrofuran (THF) and by mixing in the melt form, in a discontinuous mixer, PVC and multi-block copolymers containing poly(ϵ-caprolactone) (PCDT) and poly(ethylene glycol) (PEG) segments. PCDT-PEG copolymers were synthesized using a polycondensation reaction where the α,ω-bis-chloroformate of an oligomeric poly(ϵ-caprolactone) diol terminated (PCDT) and oligomeric PEG were employed as macromonomers. For comparison purposes, blends PVC with starting oligomers as well as with mixtures containing a typical low molecular plasticizer, dioctylphthalate (DOP), were also prepared. The copolymer miscibility was studied by differential scanning calorimetry (DSC) and FT-IR spectroscopy. The blend morphology was investigated by polarized light microscopy (PLM). A higher miscibility with PVC was observed for copolymers compared to PEG.     

Evaluation of compatibility and properties of biodegradable polyester blends

Three different biodegradable polyesters, namely, polycaprolactone (PCL), polybutylene succinate (BIONOLLE), and a copolyester of adipic acid, terephthalic acid, and 1,4‐butanediol (EASTAR) were melt‐blended using a twin‐screw extruder. The percentage composition of each of the aforementioned polymers was varied to obtain different blends, and the mechanical properties were evaluated. Selected blends showed significant improvement in tensile strength as compared with the individual polymers used to prepare the blend. The compatibility between the polymer phases was examined via Fourier transform infrared (FTIR) and nuclear magnetic resonace (NMR) spectroscopy as well as dynamic mechanical analysis. FTIR and NMR data confirmed the occurrence of hydrogen‐bonding and ester‐interchange reactions. Thermal properties and changes in crystallinity of the blends were examined with differential scanning calorimetry and X‐ray diffraction. A considerable increase in crystallinity was shown by the blend system containing BIONOLLE/PCL. The morphology of the blends was observed and correlated to the improved mechanical properties of the blend system. Results revealed an intermediate multiphase system in which a significant degree of mixing was achieved through the chemical interaction of the functional groups present, while using the twin‐screw extruder. Significant improvement in mechanical properties of some blends was observed, and information about the miscibility of these polyesters is provided. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 2003–2014, 2002     

Study of the miscibility and the thermal degradation of PVC/PMMA blends

The aim of this paper is to study the miscibility and the thermal degradation of PVC/PMMA blends. For that purpose, blends of variable compositions from 0 to 100 wt% were prepared with and without plasticizer. Their physico-chemical characterization was carried out by differential scanning calorimetric analysis (DSC) and Fourier transform infrared spectroscopy (FTIR). Their thermal degradation under nitrogen at 185°C was studied and the HCl evolved from PVC was measured by the pH method. Degraded samples were characterized, after purification, by FTIR and UV-visible spectroscopy. The DSC analysis showed polymer miscibility up to 60 wt% of PMMA. This miscibility is due to a specific interaction of hydrogen bonding type between carbonyl groups (C=O) of PMMA and hydrogen from (CHCl) groups of PVC as evidenced by FTIR analysis. On the other hand, it was found that PMMA exerted a stabilizing effect on the thermal degradation of PVC by reducing the zip dehydrochlorination and by leading to the formation of short polyenes.     

Effect of molecular interactions on the miscibility and structure of polymer blends

The effect of polymer-polymer interactions on the miscibility and macroscopic properties of PVC/PMMA, PVC/PS and PMMA/PS blends were studied in the entire composition range. The miscibility of the components was characterized by the Flory-Huggins interaction parameter or by quantities related to it. Thermal analysis, light transmittance measurements, and scanning electron microscopy were carried out on the blends and their mechanical properties were characterized by tensile tests. Interactions were analyzed by infrared spectroscopy and contact angle measurements. All three polymer pairs form heterogeneous blends, but the strength of molecular interactions is different in them, the highest is in PVC/PMMA system resulting in partial miscibility of the components and beneficial mechanical properties. The structure of these blends depends strongly on composition. A phase inversion can be observed between 0.5 and 0.6 PMMA content accompanied with a significant change in structure and properties. The PVC/PS and the PMMA/PS pairs are immiscible, though the results indicate the partial solubility of the components. The analysis of the surface characteristics of the components and the comparison of quantities derived from them with miscibility as well as with the macroscopic properties of blends revealed that blend properties cannot be predicted in this way, since they are affected by several factors.     

Study of the properties of rigid and plasticized PVC/PMMA blends

The aim of this work is to study the structure-properties relationship of rigid and plasticized PVC/PMMA blends. For that purpose, blends of variable compositions were prepared in the absence and in the presence of a plasticizer di (ethyl-2 hexyl) phtalate or DEHP. The miscibility of the two polymers was investigated by differential scanning calorimetric analysis (DSC) and Fourier transform infrared spectroscopy. The weight loss from 30 to 600°C was investigated by thermogravimetric analysis (TGA). The thermal degradation under nitrogen at 185°C was studied and the amount of HCl released from PVC was measured by the pH method. Furthermore, the variation of mechanical properties such as tensile behavior, hardness and impact resistance was investigated for all blend compositions.     

Synthesis and characterization of a vinyl‐terminated benzoxazine monomer and its blends with poly(ethylene oxide)

A vinyl‐terminated benzoxazine (VB‐a), which could be polymerized through ring‐opening polymerization, was synthesized through the Mannich condensation of bisphenol A, formaldehyde, and allylamine. This VB‐a monomer was then subjected to blending with poly(ethylene oxide) (PEO), followed by thermal curing, to form poly(VB‐a)/PEO blends. The specific interactions, miscibility, morphology, and thermal properties of these blends were investigated with Fourier transform infrared (FTIR) spectroscopy, differential scanning calorimetry, dynamic mechanical analysis (DMA), and scanning electron microscopy (SEM). Before curing, we found that PEO was miscible with VB‐a, as evidenced by the existence of a single composition‐dependent glass transition temperature (T_g) for each composition. The FTIR spectra revealed the presence of hydrogen‐bonding interactions between the hydroxyl groups of poly(VB‐a) and the ether groups of PEO. Indeed, the ring‐opening reaction and subsequent polymerization of the benzoxazine were facilitated significantly by the presence of PEO. After curing, DMA results indicated that the 50/50 poly(VB‐a)/PEO blend exhibited two values of T_g: one broad peak appeared in the lower temperature region, whereas the other (at ca. 327 °C, in the higher temperature region) was higher than that of pristine poly(VB‐a) (301 °C). The presence of two glass transitions in the blend suggested that this blend system was only partially miscible. Moreover, SEM micrographs indicated that the poly(VB‐a)/PEO blends were heterogeneous. The volume fraction of PEO in the blends had a strong effect on the morphology. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 644–653, 2007     

Miscibility and surface properties of fluorinated copolymer blends involving hydrogen‐bonding interactions

The miscibility and underlying hydrogen‐bonding interactions of blends of a fluorinated copolymer containing pyridine and a nonfluorinated copolymer containing methacrylic acid were studied with differential scanning calorimetry (DSC), transmission Fourier transform infrared (TX‐FTIR) spectroscopy, and X‐ray photoelectron spectroscopy (XPS), whereas the surface properties of the blends were investigated with contact‐angle measurements, time‐of‐flight secondary‐ion mass spectroscopy, XPS, and attenuated total reflectance Fourier transform infrared spectroscopy. DSC studies showed that the presence of a sufficient amount of 4‐vinylpyridine units in the fluorinated copolymer produced miscible blends with the nonfluorinated copolymer containing methacrylic acid. TX‐FTIR and XPS showed the existence of pyridine–acid interpolymer hydrogen‐bonding interactions. Even though the anchoring effect of hydrogen bonding hindered the migration of the fluorinated component to the blend surface, it could not completely eliminate the surface enrichment of the fluorinated component and the surface rearrangement of the fluorinated pendant chain. The air–blend interface was mainly occupied by the fluorinated pendant chain, and the surface energies of the blends were extremely low, even with only 1.5 wt % of the fluorinated component in the blends. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1145–1154, 2004     

无水AlCl_3催化PVC/PS反应性增容的研究

以无水AlCl3为催化剂,通过聚氯乙烯(PVC)与聚苯乙烯(PS)之间Friedel-Crafts反应,实现了PVC/PS共混体系的反应性增容,使PVC与PS熔融共混温度由160℃降为140℃;通过预碾磨和加入苯乙烯(St)的方法,提高材料韧性,制备了综合力学性能良好的PVC/PS合金材料.应用FTIR、DSC、SEM和力学性能测试等手段表征了合金材料的结构与性能.结果表明,FTIR出现了1943和838 cm-12个苯环对位被取代的特征吸收峰;DSC在89℃出现了玻璃化转变;SEM证明PVC/PS两相界面粘接性随AlCl3、St的加入越来越好.在PS、AlCl3和St的质量分数分别为6%,0.6%和9%时,实现了对PVC的增强增韧.合金拉伸强度达到60.54MPa,比PVC的49.35 MPa提高了22.7%;缺口冲击强度达到5.3 kJ/m2,比PVC的3.9 kJ/m2提高了35.9%.     

Preparation and characterization of thermoplastic elastomer of poly(vinyl chloride) and chlorinated waste rubber

In order to develop applications for the abundant waste rubber powder, chlorinated waste rubber (Cl-WR) was prepared by a water based chlorination method using chlorine as chlorinating agent. In this paper, Cl-WR was used as an elastic filler and blended with poly(vinyl chloride) (PVC) matrix to develop a new thermoplastic elastomer PVC/Cl-WR. The mechanical properties, hydrophilicity, swelling resistance, morphology and thermal properties of PVC/Cl-WR were characterized and compared with those of PVC/waste rubber powder (PVC/WR) blends. The results indicated that the mechanical properties, hydrophilicity, swelling resistance and thermal properties of the PVC/Cl-WR blends showed noticeable improvements over PVC/WR blends due to the improved polarity of Cl-WR. Also, the excellent miscibility and compatibility of Cl-WR with PVC was demonstrated by scanning electron microscope (SEM) images of the resulting blends.     

Synthesis and Characterization of a Branched Poly(Methacrylamide): Thermal Stability and Molecular Simulation Studies of Their Blends With Vinylic Polymers

The synthesis of a poly(diethylaminoethyl methacrylamide) (BP), based on a lineal methacrylamide with diethylaminoethyl branches was carried out. Thermal behavior was studied by thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). Relatively high thermal stability is found. Blends with poly(methylmethacrylate) (PMMA), poly(acrylic acid) (PAA) and poly(monomethyl itaconate) (PMMI) were prepared. Their thermal properties in blends were studied together with miscibility, in order to improve thermal properties of vinylic polymer blends. An increase of thermal stability was found for certain blend compositions. By FTIR analysis, higher band displacements were found for low BP compositions. AFM and molecular simulation analysis were carried out in order to elucidate the structural origin leading to thermal stability and miscibility increases. Hydrophobic interactions among methyl end groups of BP and methylene groups of vinylic polymers should be the responsible of miscibility and thermal stability increases.     

Thermal degradation studies in poly(vinyl chloride)/poly(methyl methacrylate) blends

The miscibility, morphology, and thermal properties of poly(vinyl chloride) (PVC) blends with different concentrations of poly(methyl methacylate) (PMMA) have been studied. The interaction between the phases was studied by FTIR and by measuring the glass transition temperature (T_g) of the blends using differential scanning calorimetry. Distribution of the phases at different compositions was studied through scanning electron microscopy. The FTIR and SEM results show little interaction and gross phase separation. The thermogravimetric studies on these blends were carried out under inert atmosphere from ambient to 800 °C at different heating rates varying from 2.5 to 20 °C/min. The thermal decomposition temperatures of the first and second stage of degradation in PVC in the presence of PMMA were higher than the pure. The stabilization effect on PVC was found most significant with 10 wt% PMMA content in the PVC matrix. These results agree with the isothermal degradation studies using dehydrochlorination and UV-vis spectroscopic results carried out on these blends. Using multiple heating rate kinetics the activation energies of the degradation process in PVC and its blends have been reported.     

Preparation and Characterization of Blend Films of Poly(Vinyl Alcohol) and Sodium Alginate

Blend films of poly(vinyl alcohol) (PVA) and sodium alginate (NaAlg) were prepared by casting from aqueous solutions. This blend films were characterized by tensile strength test, Fourier transform infrared spectroscopy (FT‐IR), thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). The miscibility in the blends of PVA and NaAlg was established on the basis of the thermal analysis results. DSC showed that the blends possessed single, composition‐dependent glass transition temperatures (T_gs), indicating that the blends are miscible. FT‐IR studies indicate that there is the intermolecular hydrogen bonding interactions, i.e. –OH…^?OOC– in PVA/NaAlg blends. The blend films also exhibited the higher thermal stability and their mechanical properties improved compared to those of homopolymers.     

FTIR Studies of Doped PMMA - PVC Blend System

The IR spectroscopy study shows miscibility between PMMA-PVC blends due to hydrogen bonding between CO of PMMA and hydrogen from CHCl of PVC. This blend system is doped by Camphor Sulphonic Acid (CSA) in the entire composition range. The doping of CSA in PVC, in PMMA and in PMMA-PVC blends shows changes in FTIR spectra. The interaction between PVC and CSA is through hydrogen bonding between CO of CSA and CHCl of PVC. Doping PMMA with CSA, indicate an interaction between H⁺ ion of CSA and oxygen atoms of CO and  OCH₃ of PMMA. Whereas in PMMA–PVC blend interaction between H⁺ ion of CSA and oxygen atom of CO of PMMA.     

Compatibility of poly(vinyl chloride) with polyalkyleneoxides. II. Poly(propylene oxide) and poly(tetramethylene oxide)

This study [Part II of a series dealing with the compatibility of polyalkyleneoxides with poly(vinyl chloride)] examines blends of PVC with poly(propylene oxide) (PPrO) and poly(tetra-methylene oxide) (PTMO), covering the entire composition range. Morphological, dynamic mechanical and thermal properties investigated indicate that PVC/PPrO blends are incompatible, whereas the PVC/PTMO system shows miscibility in the melt. For this polyblend and at high polyether compositions where the Hoffman–Weeks analysis can be applied, T_m equilibrium data allow the determination of the thermodynamic interaction parameter, χ₁₂ = ?0.15. Experimental compatibility data of all polyether-PVC pairs investigated in Parts I and II are also used to test various blend miscibility prediction schemes, using solubility parameter theory and recent theory on copolymer-copolymer miscibility.     

线性聚酯酰胺对聚碳酸亚丙酯的改性

通过己内酯和氨基己酸开环、缩合反应制备了酯段含量为81%的线性聚酯酰胺（PEA）,并用熔融共混的方法制备了PEA/聚碳酸亚丙酯（PPC）共混物,考察了PEA的引入对共混体系相容性、热力学稳定性和机械性能的影响。 结果表明,PEA与PPC之间有较好的相容性,共混物的热力学稳定性比PPC有显著提高,当PEA质量分数为3%时,共混体系的起始分解温度（T-5%）和最大分解速率时的温度（Tmax）比PPC分别提高了52.7%和46.4%。 通过调节PEA的含量可以使共混体系同时达到增强和增韧的效果。     

Studies on poly(ε‐caprolactone)/thiodiphenol blends: The specific interaction and the thermal and dynamic mechanical properties

The effects of several low molecular weight compounds with hydroxyl groups on the physical properties of poly(ε‐caprolactone) (PCL) were investigated by Fourier transform infrared (FTIR) spectroscopy and high‐resolution solid‐state ¹³C NMR. PCL and 4,4′‐thiodiphenol (TDP) interact through strong intermolecular hydrogen bonds and form hydrogen‐bonded networks in the blends at an appropriate TDP content. The thermal and dynamic mechanical properties of PCL/TDP blends were investigated by differential scanning calorimetry (DSC) and dynamic mechanical thermal analysis, respectively. The melting point of PCL decreased, whereas both the glass‐transition temperature and the loss tangent tan δ of the blend increased with an increase in TDP content. The addition of 40 wt % TDP changed PCL from a semicrystalline polymer in the pure state to a fully amorphous elastomer. The molecules of TDP lost their crystallizability in the blends with TDP contents not greater than 40 wt %. In addition to TDP, three other PCL blend systems with low molecular weight additives containing two hydroxyl groups, 1,4‐dihydroxybenzene, 1,4‐di‐(2‐hydroxyethoxy) benzene, and 1,6‐hexanediol, were also investigated with FTIR and DSC, and the effects of the chemical structure of the additives on the morphology and thermal properties are discussed. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 1848–1859, 2000     

Effect of epoxidized sunflower oil on polylactic acid properties

Epoxidized sunflower oil (ESO) was utilized as a plasticizer for polylactic acid (PLA) using chloroform as a solvent by a solution casting process at various ratios of PLA to ESO. Fourier-transform infrared (FTIR) spectroscopy was used to identify the functional groups of PLA, ESO, and PLA/ESO blends. Thermal stability and mechanical and morphological properties of the blends were investigated by thermogravimetric analysis, tensile property measurements, and scanning electron microscopy technique, respectively. The FTIR spectra indicate that there are some molecular interactions by intermolecular hydrogen bonding between PLA and ESO. PLA/ESO blends show high thermal stability and significant improvement of mechanical properties compared with pure PLA. The highest elongation at break was obtained when the ratio of the PLA/ESO blend was 80/20. Morphological results of PLA/ESO blends show that ESO was well miscible with PLA.     

Thermal and photochemical stability of poly(vinyl alcohol)/modified lignin blends

A kraft lignin derivative (KLD) obtained by reaction with p-aminobenzoic acid/phthalic anhydride was blended with poly(vinyl alcohol) (PVA) by solution casting from DMSO. PVA and PVA/KLD films were exposed to ultraviolet radiation (24, 48, and 96 h) and analyzed by thermogravimetry (TG), differential scanning calorimetry (DSC), infrared spectroscopy (FTIR), hydrogen nuclear magnetic resonance (¹H NMR) spectroscopy, and scanning electron microscopy (SEM). PVA films show a loss of thermal stability due to irradiation. PVA/KLD reveals greater thermal stability than PVA and an increase in thermal stability after irradiation. These results suggest that the incorporation of KLD into PVA provides a gain in thermal and photochemical stability. FTIR, ¹H NMR, DSC, and TG results obtained for the blends suggest that intermolecular interactions between PVA and KLD chains are present. SEM micrographs revealed blend miscibility for a KLD blend content of up to 15 wt%, as observed at magnification of 1000 times.