Development and evaluation of a diffusive gradients in a thin film technique for measuring ammonium in freshwaters

A new diffusive gradients in a thin film (DGT) technique, using Microlite PrCH cation exchange resin, was developed and evaluated for measuring NH₄–N in freshwaters. Microlite PrCH had high uptake (>92.5%) and elution efficiencies (87.2% using 2 mol L⁻¹ NaCl). Mass vs. time validation experiments over 24 h demonstrated excellent linearity (R² ≥ 0.996). PrCH-DGT binding layers had an extremely high intrinsic binding capacity for NH₄–N (∼3000 μg). NH₄–N uptake was quantitative over pH ranges 3.5–8.5 and ionic strength (up to 0.012 mol L⁻¹ as NaCl) typical of freshwater systems. Several cations (Na⁺, K⁺, Ca²⁺ and Mg²⁺) were found to compete with NH₄–N for uptake by PrCH-DGT, but NH₄–N uptake was quantitative over concentration ranges typical of freshwater (up to 0.012 mol L⁻¹ Na⁺, 0.006 mol L⁻¹ K⁺, 0.003 mol L⁻¹ Ca²⁺ and 0.004 mol L⁻¹ Mg²⁺). Effective diffusion coefficients determined from mass vs. time experiments changed non-linearly with electrical conductivity. Field deployments of DGT samplers with varying diffusive layer thicknesses validated the use of the technique in situ, allowed deployment times to be manipulated with respect to NH₄–N concentration, and enable the calculation of the diffusive boundary layer thickness. Daily grab sample NH₄–N concentrations were observed to vary considerably independent of major rainfall events, but good agreements were obtained between PrCH-DGT values and mean grab sample measurements of NH₄–N (C_DGT:C_SOLN 0.83–1.3). Reproducibility of DGT measurements in the field was good (relative standard deviation < 11%). Limit of detection was 0.63 μg L⁻¹ (equivalent to 0.045 μmol L⁻¹) based on 24 h deployments.     

Use of Saccharomyces cerevisiae immobilized in agarose gel as a binding agent for diffusive gradients in thin films

A new binding agent, consisting of the yeast Saccharomyces cerevisiae immobilized in agarose, is proposed for use in diffusive gradients in thin films (DGT). Different gel compositions, containing from 4.5% to 20% (m/v) of S. cerevisiae and 1.5-5.0% (m/v) of agarose, were prepared and tested for uptake of Cd(II). For gels containing 20% (m/v) of S. cerevisiae, a mass of 14,900 ng has been attributed as the uptake limit of Cd for each disk. Determination of the Cd retained in the binding agent was readily carried out using a slurry of the agarose-yeast disk introduced directly into the inductively coupled plasma optical emission spectrometer. The performance characteristics of the DGT samplers, which were assembled with the proposed binding agent (25 mm disk containing 20% of S. cerevisiae and 1.5% of agarose) and a diffusive layer of cellulose (chromatographic paper 3MM Chr of 25 mm diameter), were evaluated by measuring the Cd(II) uptake at various pH values and ionic strengths. Very consistent results were found within the pH range 4.5-7.5 and at ionic strengths ≥0.005 mol L⁻¹. The precision of DGT measurements was characterized by relative standard deviations of <8%. No changes in the uptake of Cd(II) were observed in the samplers that were assembled with recently prepared disks or 35-day-old stored disks. The proposed material has been applied to the analyses of river and sea water samples. For determination of Cd(II), excellent agreement between the results obtained from devices assembled with the proposed material and those assembled with conventional material (Chelex-100 resin) were obtained, strongly validating the use of the agarose-yeast gel disk as a new binding agent for DGT.     

Performance of the diffusive gradients in thin films technique for measuring Ca and Mg in freshwater

Measurements of the major cations Ca and Mg by the technique of diffusive gradients in thin films (DGTs) were systematically evaluated. The concentration in solution was calculated using Fick’s first law of diffusion from the directly measured flux to the DGT device. A selective cation exchange resin (Bio-Rad Chelex^®100), which has been used extensively with DGT for trace metals, such as Cd²⁺, Cu²⁺ and Ni²⁺, was used for this work.

Elution of Ca and Mg from the resin with 1 M HNO₃ was very reproducible. Measurements of Ca and Mg concentrations in synthetic solutions agreed well with the theoretical predictions. The negative response on uptake caused by lowered pH was investigated. Uptake was found to decline below pH 5. The capacity of the DGT device for Ca and Mg was also investigated to establish maximum deployment times for given concentrations.

Experiments with filtered and modified lake water show that DGT can be used to measure Ca and Mg when trace metals are present in the solution. An in situ deployment of DGT combined with an ultrafiltration study suggest that the Mg concentration measured by DGT is similar to the concentration found in the fraction <1 kDa.     

Speciation measurements of uranium in alkaline waters using diffusive gradients in thin films technique

This work investigated the application of diffusive gradients in thin films technique (DGT) to uranium speciation measurements in natural water. Two binding phases were examined, a commercially available affinity membrane, Whatman DE 81 (DE 81), with amino binding functional groups and the conventionally used Chelex 100 beads imbedded polyacrylamide hydrogel (Chelex) with iminodiacetate functional groups. The DGT devices assembled with the binding phases of DE 81 (DE 81 DGT) and Chelex gel (Chelex DGT) were tested both in synthetic river water solutions and in local river water. DE 81 DGT and Chelex DGT measured 80% and 75% of the total uranium in synthetic river water solution, respectively, and measured 73% and 60% of the total uranium in St. Lawrence River, Canada, respectively. The binding properties of the DE 81 membrane and Chelex gel for uranium, and the diffusion of uranyl complexes in the polyacrylamide gel (PAM) were also studied.     

Diffusive gradients in thin films technique for uranium measurements in river water

The diffusive gradients in thin films technique (DGT) was used for uranium measurements in water. DGT devices with Dowex resin binding phase (Dow DGT) were tested in synthetic river water, which gave 84% response to total uranium concentration. The devices were also deployed in natural river water and compared to devices with other types of binding phases, Chelex 100 resin beads imbedded in polyacrylamide hydrogel (Chelex DGT) and DE 81 anion exchange membrane (DE DGT), deployed in the same location at the same time. The measurement by Dow DGT was the lowest among the different types of the DGT devices, 45% of total uranium, while measurement by DE DGT was the highest, 98% of total uranium. The results achieved by the three types of DGT devices were explained by three DGT working mechanisms, equilibrium between complexes of resin/uranyl carbonates and complexes of resin/competitive ligands in water, effective reduction of uranyl carbonate concentration by the binding phase and dissociation of UO₂(CO₃)₂²⁻ and UO₂(CO₃)₃⁴⁻ within the diffusive layer in a DGT device. It is hoped that by deploying the DGT devices with different binding phases in natural waters, additional information on uranium speciation could be obtained.     

Diffusion characteristics of agarose hydrogel used in diffusive gradients in thin films for measurements of cations and anions

The agarose hydrogel has been increasingly used as a diffusive layer in diffusive gradients in thin films (DGT) measurements. However its diffusive characteristics have not been examined in detail. In this study, the performance of agarose gel was tested in DGT measurements of eight cations (Fe(II), Mn(II), Co(II), Ni(II), Cu(II), Zn(II), Pb(II), and Cd(II)) and eight anions (P(V), As(V), Cr(VI), Mo(VI), Sb(V), Se(VI), V(V), and W(VI)). It was found that the thickness of agarose, a key parameter in the calculation of DGT measured concentration, remained unchanged after hydration followed by storage under the following conditions: pH 2–11, ionic strength 0–1.0 M, temperature 4–40 °C, and with the storage time extending to 300 d. Enrichment of cations and repelling of anions were observed in the gel under the ionic strengths of < 2–3 mM and <1 mM (NaNO₃), respectively, which was attributed to the electrostatic interactions of these ions with the fixed negatively charged groups (mainly pyruvate) in the gel. The diffusion coefficients of cations and anions through the agarose gel (plus a PVDF filter membrane) were on average 1.10 ± 0.04 times of the reported diffusion coefficients through the agarose cross-linked polyacrylamide (APA) hydrogel, typically used in DGT technique. The working pH ranges for the agarose gel-assembled DGTs were 4–10 and 5–9 for anions and cations, respectively. The use of agarose gel, either individually or along with different filter membranes, affected the overall diffusion rates of cations and anions. The measured DGT concentrations of cations and anions in filtered natural freshwater and seawater were mostly in line with those measured directly. The results showed that the agarose gel can be used as one of the standard diffusive layers in DGT measurements for a wide range of inorganic and organic analytes.     

Use of the diffusive gradients in thin films technique to evaluate (bio)available trace metal concentrations in river water

Concentrations of Cd, Cu, Cr, Pb, Ni and Zn were monitored in the Svitava River (the Czech Republic) during April and September 2005. Total concentrations and total dissolved concentrations were obtained through regular water sampling, and the diffusive gradients in thin films technique (DGT) were used to gain information on the kinetically labile metal concentrations. Each measured concentration was compared with the corresponding average (bio)available concentration calculated from the mass of metal accumulated by the moss species Fontinalis antipyretica. The concentrations of Cd, Pb, Cr and Zn measured using DGT corresponded well with those obtained after the deployment of Fontinalis antipyretica moss bags in the Svitava River, but the concentrations of Cu and Ni did not. The calculated (bio)available Cu concentration correlated well with the total dissolved concentration of Cu, whereas no correlation was found to exist between the concentrations of Ni. Scheme of the Svitava River monitoring station, including the DGT sampling units and Fontinalis antipyretica moss bags Electronic supplementary material Supplementary material is available in the online version of this article at and is accessible for authorized users.     

Assessment of trace metal binding kinetics in the resin phase of diffusive gradients in thin films

The dynamic technique of diffusive gradients in thin films (DGT), that measures metal speciation in situ, has found wide environmental application. Simple interpretation of the metal accumulation in terms of a solution concentration has assumed that trace metals do not penetrate beyond the surface of the binding layer, but penetration, although theoretically discussed has not yet been directly measured. Multiple binding layers were used to enable analysis of different depths of a DGT binding phase (Chelex-100 or iminodiacetate resins). In simple metal solution (no ligand) at pH 7, metal penetration to the back layer was low and similar for all metals. However, at lower pH up to 42% of an individual metal accumulated in the back resin layer. This was most noticeable for Mn at pH 4 and 5, but Cd and Co were also affected at pH 4. These results were consistent with rate limited binding, particularly for Mn. A kinetic model successfully fitted the data and allowed derivation of a binding rate constant and the mean distance that metals penetrate into a resin gel (λ_M). Only for Mn, Co and Cd were experimentally derived λ_M values greater than the diameter of a Chelex-100 resin bead. For most situations, then, the penetration into the binding layer is negligible and binding of trace metal ions can be regarded as instantaneous, validating the simple use and interpretation of DGT. For weakly binding metals at low pH the slower binding allows penetration, which may affect the DGT measurement.     

Performance characteristics of suspended particulate reagent-iminodiacetate as a binding agent for diffusive gradients in thin films

The performance characteristics of an alternative binding agent, suspended particulate reagent-iminodiacetate (SPR-IDA), for use with DGT methodology were investigated. The parameters investigated during this study included gel hydration, blank levels, elution factor (f_e), capacity, the effects of pH on the binding of trace metals by DGT. The novel application of this resin for use as a quantitative standard for laser ablation ICP-MS was also evaluated. To further constrain the results for the SPR-IDA binding agent, parallel experiments were performed using resin gel containing Chelex 100, which has been widely reported in the literature. Hydration results showed that the SPR-IDA resin gel reached a stable dimension and weight within ∼30 min and was dimensionally stable for ≤6 months. The measured DGT blanks for the SPR-IDA resin were 0.0023, 0.15, 0.21, 0.0033 and 0.011 ng disc⁻¹ for Co, Ni, Cu, Cd and Pb, respectively. The elution factor differed for the two resin types with the Chelex 100 recoveries slightly lower than previous reports and the SPR-IDA resin showing on average ∼5-9% better recoveries than DGT containing Chelex 100. The measured capacity of DGT discs containing the SPR-IDA binding agent was 0.26 mg Cd, similar to the calculated value of 0.29 mg Cd, indicating the entire resin layer was available for metal uptake.Both resin types performed equally well when deployed in 1 mM NaNO₃ solutions with DGT measurements of ∼100% of direct solution measurements for Co, Ni and Cd. However, DGT measurements of Cu and Pb systematically decreased with increasing solution pH down to ∼50% of solution values at pH 8.0, due to artifacts resulting from colloid formation during the addition of the metals. This was remedied by adding the metals as dilute salt standards and addition of Mg(NO₃)₂ to eliminate adsorption to the container walls. In the latter experiments, DGT measured concentrations of Co, Ni, Cu, Cd and Pb were in agreement with solution concentrations. Deployment of DGT in solutions with increasing concentrations of trace metals yielded linear results, suggesting that quantitative analysis using simplified laser ablation techniques should be possible using this newly characterized SPR-IDA resin gel.     

Mercury depth profiles in river and marine sediments measured by the diffusive gradients in thin films technique with two different specific resins

The diffusive gradients in thin films technique (DGT) was used to measure depth profiles of mercury in river and marine sediments in situ to a spatial resolution of 0.5 cm. Agarose gel was used as the diffusive gel in the DGT probes. Two different selective resins—Chelex 100 with iminodiacetic groups and Spheron-Thiol with thiol groups incorporated in the polyacrylamide resin gel—were tested. The different capture efficiencies of the two adsorbents enabled the fractions of mercury bound in different species in sediment pore water to be estimated. Mercury concentrations obtained by DGT with Spheron-Thiol resin were very similar to those obtained after centrifugation. This indicates that DGT with Sheron-Thiol resin reports on total dissolved mercury levels. The concentration of mercury measured by DGT with Chelex-100 resin was much lower (by a factor of 5–20) for the same sediment samples. Chelex-100 does not have such a high affinity to mercury as Spheron-Thiol, and so it only reports on the content of labile mercury species, such as inorganic ions and weak complexes. The content of labile mercury species in the river sediment was approximately 20% of the total dissolved mercury in pore water, whereas in marine sediment only 7% of the mercury was present as labile species.     

Effect of competitive cation binding on the measurement of Mn in marine waters and sediments by diffusive gradients in thin films

The possible adverse effect of competitive binding on DGT (diffusive gradients in thin films) measurements of metals in marine situations was investigated. Of the divalent transition metals, manganese binds most weakly to Chelex resin and is most likely to be affected by competition. In media resembling seawater, the Chelex within DGT devices becomes saturated with Ca and Mg within 2 h, and at pH 5–6 the sensitivity of the DGT measurement for Mn is substantially reduced, due to the appreciable concentration of Mn in contact with the resin. For media resembling freshwater DGT gives a near theoretical response for Mn. Iron was shown to be capable of displacing Mn and to a more limited extent Cd from the resin when its capacity for Fe is approached. Vertical profiles of Mn in a mesocosm sediment, obtained by deploying DGT for different times, could be explained by this displacement effect. The problem only occurs when Fe concentrations are exceptionally high and can be avoided by using short deployment times, typically less than 12 h. Whilst most trace metals can be simply measured by deploying DGT in marine systems, for Mn consideration should be given to possible effects associated with the capacity of the Chelex binding layer being approached by accumulation of the other cations present.     

Application of a cellulose phosphate ion exchange membrane as a binding phase in the diffusive gradients in thin films technique for measurement of trace metals

The technique of diffusive gradients in thin films (DGT) is a newly developed analytical technique capable of measuring in situ concentrations of trace metals in the environment. The technique employs a thin film diffusive hydrogel (with well-defined diffusion properties) in contact with a binding phase capable of binding metal ions of interest. In this work, we demonstrate, for the first time, the use of a commercially available solid ion exchange membrane (Whatman P81) as the binding phase in DGT analysis. The cellulose phosphate-based Whatman P81 membrane is a strong cation exchange membrane. Its performance characteristics as a new binding phase in DGT measurement of Cu²⁺ and Cd²⁺ were systematically investigated. Several advantages over the conventional ion exchange resin-embedded hydrogel binding phases used in DGT were observed including simple preparation, ease of handling, and reusability. The binding capacities of the material to various metal ions were examined both collectively and individually. The binding phase preferentially binds to transition metal ions rather than matrix ions such as potassium, sodium, calcium and magnesium, which are competitive species in natural waters. Within the optimum pH range (pH 4.0-9.0), the maximum non-competitive binding capacities of the membrane for Cu²⁺ and Cd²⁺ were 3.22 and 3.07 μmol cm⁻², respectively. The suitability of the new membrane-based binding phase for DGT applications was validated experimentally. The experimental results demonstrated excellent agreement with theoretically predicted trends. The measurement was not degraded after four consecutive reuses of the cellulose phosphate binding phase.     

An evaluation of ferrihydrite- and Metsorb™-DGT techniques for measuring oxyanion species (As,Se, V,P): Effective capacity,competition and diffusion coefficients

This study investigated several knowledge gaps with respect to the diffusive gradients in thin films (DGT) technique for measurement of oxyanions (As(III), As(V), Se(IV), Se(VI), PO₄³⁻, and V(V)) using the ferrihydrite and Metsorb™ binding layers. Elution efficiencies for each binding layer were higher with 1:20 dilutions, as analytical interferences for ICP-MS were minimised. Diffusion coefficients measured by diffusion cell and by DGT time-series experiments were found to agree well and generally agreed with previously reported values, although a range of diffusion coefficients have been reported for inorganic As and Se species. The relative binding affinity for both ferrihydrite and Metsorb™ was PO₄³⁻ ≈ As(V) > V(V) ≈ As(III) > Se(IV) ? Se(VI) and effective binding capacities were measured in single ion solutions, and spiked synthetic freshwater and seawater, advising practical decisions about DGT monitoring. Under the conditions tested the performance of both ferrihydrite and Metsorb™ binding layers was directly comparable for As(V), As(III) Se(IV), V(V) and PO₄³⁻ over a deployment spanning ≤2 days for both freshwater and seawater. In order to return quantitative data for several analytes we recommend that the DGT method using either ferrihydrite or Metsorb™ be deployed for a maximum of 2 days in marine waters likely to contain high levels of the most strongly adsorbing oxyanions contaminants. The high pH, the competitive ions present in seawater and the identity of co-adsorbing ions affect the capacity of each binding layer for the analytes of interest. In freshwaters, longer deployment times can be considered but the concentration and identity of co-adsorbing ions may impact on quantitative uptake of Se(IV). This study found ferrihydrite-DGT outperformed Metsorb-DGT while previous studies have found the opposite, with variation in binding materials masses used being a likely reason. Clearly, preparation of both binding layers should always be optimised to produce the highest capacity possible, especially for seawater deployments.     

Application of diffusive gradient in thin films technique (DGT) to measurement of mercury in aquatic systems

The diffusive gradient in thin films (DGT) technique was investigated and used to measure mercury concentration in river water. Mercury ions are covalently bound to amide nitrogen groups of commonly used polyacrylamide, which makes this gel unsuitable as a diffusive medium. In contrast, agarose gel was found as the diffusive gel for mercury measurements. Basic performance tests of agarose DGT verified the applicability of Fick's first law for DGT measurements. Two selective resins, Chelex-100 with iminodiacetic groups and Spheron-Thiol with thiol groups were used. The measured diffusion coefficient in agarose gel was close to that in water. The concentration of mercury in Svitava river measured by DGT with Speron-Thiol resin gel was higher (0.0116 ± 0.0009 μg l⁻¹) than those obtained by Chelex-100 (0.0042 ± 0.0005 μg l⁻¹). Different capture efficiencies of two adsorbents enable to estimate fractions of mercury bonded in different complexes in the river water. The concentrations of mercury found by DGT both Chelex-100 and Speron-Thiol resin gels are much lower than that measured directly in the river water (0.088 ± 0.012 μg l⁻¹). This difference indicates that DGT concerns inorganic ions and labile species only, and that it is not able to include inert organic species and colloids.     

A method for measurement of free cadmium species in waters using diffusive gradients in thin films technique with an ion-imprinted sorbent

A diffusive gradients in thin films (DGT) device for the analysis of free Cd(II) species, based on Cd(II) ion-imprinted sorbent (IIS) as the binding agents and commercial polyethersulfone membrane (PES) as diffusion layer, was developed (PES/IIS-DGT). DGT time-series experiments showed that the mass of free Cd(II) species accumulated by PES/IIS-DGT was linear vs. time (R² = 0.9953) and the concentration of free Cd(II) species by PES/IIS-DGT was in good agreement with the total dissolved concentrations of free Cd(II) species in simple synthetic solutions where free ionic species dominated. PES/IIS-DGT performance was independent in the range of pH 4.5–7.5 and ionic strength range from 1.0 × 10⁻³ to 0.7 mol L⁻¹. The measurement of free Cd(II) species in synthetic solution containing different concentrations of ligands by PES/IIS-DGT showed an excellent agreement with the value measured by Cd(II) ion selective electrodes (Cd-ISE), indicating that PES/IIS-DGT method is more suitable than Cd-ISE for the measurement of low concentration of free Cd(II) species due to the enrichment of IIS for the analytes.     

Preparation of guanidinylated carboxymethyl chitosan and its application in the diffusive gradients in thin films (DGT) technique for measuring labile trace metals in water

ABSTRACT

Guanidinylated carboxymethyl chitosan (GCMCS) was prepared via the guanidinylation of carboxymethyl chitosan (CMCS). A device employing the diffusive gradients for thin films (DGT) technique was made using a GCMCS aqueous solution as the binding agent and a cellulose acetate dialysis membrane (CADM) as the diffusion phase to measure labile Cu²⁺, Pb²⁺ and Cd²⁺ in water. The percentage uptake (U%) values of labile Cu²⁺, Pb²⁺ and Cd²⁺ in a synthetic water sample were almost consistent with the theoretical values at 101.6 ± 2.8%, 104.6 ± 6.1% and 95.9 ± 4.4%, respectively. The optimum pH ranges for the measurement of labile Cu²⁺, Pb²⁺ and Cd²⁺ were 3.0–7.0, 3.0–7.0 and 4.0–8.0, respectively. The ionic strength mainly affected the diffusion of metal ions in the CADM. The diffusion rates decreased with increasing concentrations of NaNO₃ solutions. The application of GCMCS-DGT in natural water and industrial wastewater showed that dissolved organic carbon (DOC) only affects metal species, and the accurate determination of labile Cu²⁺, Pb²⁺ and Cd²⁺ can be achieved when the diffusion coefficients of these metal ions in the diffusion phase have been determined. GCMCS is suitable for DGT application as a chelating agent for metal ions.     

Performance of the diffusive gradients in thin films technique for measurement of trace metals in low ionic strength freshwaters

A series of experiments were undertaken to investigate the effect of ionic strength and the concentration of free sodium ions in the resin gel on the performance of the diffusive gradients in thin films (DGT) technique. When the free sodium ion concentration in the resin gel was estimated by the time-dependent release into solution, it agreed with a previous estimate. However, equilibration with different volumes of water gave a higher value, suggesting that inherent averaging in the time-dependent release method underestimates the free concentration. DGT measurements of Cu and Cd were made over a wide range of ionic strengths (from 3 μmol l⁻¹ to 0.8 mol l⁻¹). For all the ionic strengths above 100 μmol l⁻¹ there was no significant difference between measurements made by DGT and measurements made directly on the solution using atomic absorption spectroscopy. Below 100 μmol l⁻¹ results were erratic. They did not comply with a theory that predicts high results for DGT based on enhancement of the diffusion coefficient of trace metal cations by counter diffusion of sodium ions. When Cd in solutions with a range of ionic strengths was measured by DGT there was no difference whether the resin gels were in Na or Ca form. Rather than counter diffusion of Na ions, it is suggested that the spurious behaviour at low ionic strength is due to interactions of the trace metals with the diffusion gel when there are insufficient excess cations present.     

Uranium aqueous speciation in the vicinity of the former uranium mining sites using the diffusive gradients in thin films and ultrafiltration techniques

The performance of the Diffusive Gradients in Thin films (DGT) technique with Chelex^®-100, Metsorb™ and Diphonix^® as binding phases was evaluated in the vicinity of the former uranium mining sites of Chardon and L'Ecarpière (Loire-Atlantique department in western France). This is the first time that the DGT technique with three different binding agents was employed for the aqueous U determination in the context of uranium mining environments. The fractionation and speciation of uranium were investigated using a multi-methodological approach using filtration (0.45 μm, 0.2 μm), ultrafiltration (500 kDa, 100 kDa and 10 kDa) coupled to geochemical speciation modelling (PhreeQC) and the DGT technique. The ultrafiltration data showed that at each sampling point uranium was present mostly in the 10 kDa truly dissolved fraction and the geochemical modelling speciation calculations indicated that U speciation was markedly predominated by CaUO₂(CO₃)₃²⁻. In natural waters, no significant difference was observed in terms of U uptake between Chelex^®-100 and Metsorb™, while similar or inferior U uptake was observed on Diphonix^® resin. In turn, at mining influenced sampling spots, the U accumulation on DGT-Diphonix^® was higher than on DGT-Chelex^®-100 and DGT-Metsorb™, probably because their performance was disturbed by the extreme composition of the mining waters. The use of Diphonix^® resin leads to a significant advance in the application and development of the DGT technique for determination of U in mining influenced environments. This investigation demonstrated that such multi-technique approach provides a better picture of U speciation and enables to assess more accurately the potentially bioavailable U pool.     

Application of the diffusive gradients in thin films technique for available potassium measurement in agricultural soils: Effects of competing cations on potassium uptake by the resin gel

The utilization of Amberlite (IRP-69 ion-exchange resin, 100–500 wet mesh) as the binding phase in the diffusive gradients in thin films (DGT) technique has shown potential to improve the assessment of plant-available K in soils. The binding phase has recently been optimized by using a mixed Amberlite and ferrihydrite (MAF) gel which results in linear K uptake over extended deployment periods and in solutions with higher K concentrations. As restriction of K uptake by Ca on the Amberlite based resin gel has been previously proposed, potential competing effects of Ca²⁺, Mg²⁺ and NH₄⁺ on K uptake by the MAF gel were investigated. These cations had no effect on K elution efficiency which was 85%. However, K uptake by the MAF gel was restricted in the presence of competing cations in solution. Consequently, the diffusion coefficient of K decreased in the presence of cations compared to previous studies but was stable at 1.12 × 10⁻⁵ cm² s⁻¹ at 25 °C regardless of cation concentrations. Uptake of K by the DGT device was affected by the presence of excessive Ca in more than 30% of twenty typical Australian agricultural soils. However, this problem could be circumvented by using a shorter deployment time than the normal 24 h. Moderate correlation of concentrations of K extracted by DGT with Colwell K (extracted by NaHCO₃, R² = 0.69) and NH₄OAc K (R² = 0.61) indicates that DGT measures a different pool of K in soils than that measured by the standard extractants used. In addition, the MAF gel has the ability to measure Ca and Mg simultaneously.     

Development of the diffusive gradient in thin films technique for the measurement of labile mercury species in waters

The diffusive gradients in thin films (DGT) technique, utilizing resin gel with ion-exchange resin Duolite GT73 and new ion-exchange resin Ambersep GT74, was investigated for the accumulation of four mercury species (Hg²⁺, CH₃Hg⁺, C₂H₅Hg⁺, C₆H₅Hg⁺). The diffusion coefficients of mercury species in agarose gel calculated on the basis of Fick’s Law were mercury species-specific. The diffusion coefficients of Hg²⁺ and CH₃Hg⁺ at 25 °C (9.07 ± 0.23 × 10⁻⁶ cm² s⁻¹ and 9.06 ± 0.30 × 10⁻⁶ cm² s⁻¹, respectively) were very similar, but the diffusion coefficients of C₂H₅Hg⁺ (6.87 ± 0.23 × 10⁻⁶ cm² s⁻¹) and C₆H₅Hg⁺ (3.86 ± 0.19 × 10⁻⁶ cm² s⁻¹) were significantly lower. Influence of experimental conditions (pH, selected cations, chlorides and humic substance) on mercury species accumulation by DGT was studied. The DGT technique was applied to river water spiked with mercury species.