Luminescence Enhancement based Sensing of L‐Cysteine by Doped Quantum Dots

The interaction of a presynthesized orange emitting Mn²⁺‐doped ZnS quantum dots (QDs) with L‐Cysteine (L?Cys) led to enhance emission intensity (at 596 nm) and quantum yield (QY). Importantly, the Mn²⁺‐doped ZnS QDs exhibited high sensitivity towards L?Cys, with a limit of detection of 0.4±0.02 μM (in the linear range of 3.3–13.3 μM) and high selectivity in presence of interfering amino acids and metal ions. The association constant of L?Cys was determined to be 0.36×10⁵ M^?1. The amplified passivation of the surface of Mn²⁺‐doped ZnS QDs following the incorporation and binding of L?Cys is accounted for the enhancement in their luminescence features. Moreover, the luminescence enhancement‐based detection will bring newer dimension towards sensing application.     

Highly-controllable imprinted polymer nanoshell at the surface of silica nanoparticles based room-temperature phosphorescence probe for detection of 2,4-dichlorophenol

This paper reports a facile and general method for preparing an imprinted polymer thin shell with Mn-doped ZnS quantum dots (QDs) at the surface of silica nanoparticles by stepwise precipitation polymerization to form the highly-controllable core–shell nanoparticles (MIPs@SiO₂–ZnS:Mn QDs) and sensitively recognize the target 2,4-dichlorophenol (2,4-DCP). Acrylamide (AM) and ethyl glycol dimethacrylate (EGDMA) were used as the functional monomer and the cross-linker, respectively. The MIPs@SiO₂–ZnS:Mn QDs had a controllable shell thickness and a high density of effective recognition sites, and the thickness of uniform core–shell 2,4-DCP-imprinted nanoparticles was controlled by the total amounts of monomers. The MIPs@SiO₂–ZnS:Mn QDs with a shell thickness of 45 nm exhibited the largest quenching efficiency to 2,4-DCP by using the spectrofluorometer. After the experimental conditions were optimized, a linear relationship was obtained covering the linear range of 1.0–84 μmol L⁻¹ with a correlation coefficient of 0.9981 and the detection limit (3σ/k) was 0.15 μmol L⁻¹. The feasibility of the developed method was successfully evaluated through the determination of 2,4-DCP in real samples. This study provides a general strategy to fabricate highly-controllable core–shell imprinted polymer-contained QDs with highly selective recognition ability.     

Cu nanoclusters-based ratiometric fluorescence probe for ratiometric and visualization detection of copper ions

Copper is a highly toxic environmental pollutant with bioaccumulative properties. Therefore, sensitive detection of Cu²⁺ is very important to prevent over-ingestion, and visual detection is preferred for practical applications. In this work, we developed a simple and environmental friendly approach to synthesize hyperbranched polyethyleneimine-protected copper nanoclusters (hPEI-Cu NCs) with great stability against extreme pH, high ionic strength, thiols etching and light illumination, which were then conjugated to the surface of silica coated CdSe quantum dots (QDs) to design a ratiometric fluorescence probe. In the presence of different amounts of Cu²⁺ ions, the fluorescence of Cu NCs can be drastically quenched, while the emission from QDs stayed constant to serve as a reference signal and the color of the probe changed from yellow-green to red, resulting in ratiometric and visualization detection of Cu²⁺ ion with high accuracy. The detection limit for Cu²⁺ was estimated to be 8.9 nM, much lower than the allowable level of Cu²⁺ in drinking water (∼20 μM) set by U.S. Environmental Protection Agency. Additionally, this probe can be also applied for the determination of Cu²⁺ ion in complex real water samples.     

Doped zinc sulfide quantum dots based phosphorescence turn-off/on probe for detecting histidine in biological fluid

We report a turn-on phosphorescence probe for detection of histidine based on Co²⁺-adsorbed N-acetyl-l-cysteine (NAC) capped Mn: ZnS quantum dots (QDs) which is directly synthesized by the hydrothermal method. The phosphorescence of NAC-Mn: ZnS QDs is effectively quenched by Co²⁺ attributing to the adsorption of Co²⁺ onto the surface of QDs with a concomitant in suppressing the recombination process of hole and electron of QDs. The phosphorescence of Co²⁺-adsorbed NAC-Mn: ZnS QDs can be recovered by binding of Co²⁺ with histidine. The quenching and regeneration of the phosphorescence of NAC-Mn: ZnS QDs have been studied in detail. The as-prepared QDs-based probe is applied to determine histidine with a linear range of 1.25–30 μM and a detection limit of 0.74 μM. The relative standard deviation for eleven repeat detections of 20 μM histidine is 0.65%. Co²⁺-adsorbed NAC-Mn: ZnS QDs show high sensitivity and good selectivity to histidine over other amino acids, metal ions and co-existing substances. The proposed QDs probe has been successfully applied to determination of histidine in human urine samples with good recoveries of 98.5–103%.     

An improved method for ratiometric fluorescence detection of pH and Cd using fluorescein isothiocyanate–quantum dots conjugates

In this study, thioglycolic acid capped-CdTe quantum dots (QDs) were modified by polyethylenimine (PEI), and then combined with fluorescein isothiocyanate (FITC) to fabricate FITC–CdTe conjugates. The self-assembly of FITC, CdTe and PEI was ascribed to electrostatic interactions in aqueous solution. The resulting conjugates were developed toward two routes. In route one, ratiometric photoluminescence (PL) intensity of conjugates (I_FITC/I_QDs) was almost linear toward pH from 5.3 to 8.7, and a ratiometric PL sensor of pH was favorable obtained. In route two, firstly added S²⁻ induced remarkable quenching of QDs PL peak (at the “OFF” state), which was restored due to following addition of Cd²⁺ (at the “ON” state). In the conjugates, successive introduction of S²⁻ and Cd²⁺ hardly influenced on FITC PL peaks. According to this PL “OFF-ON” mode, a ratiometric PL method for the detection of Cd²⁺ was achieved. Experimental results confirmed that the I_FITC/I_QDs exhibited near linear proportion toward Cd²⁺ concentration in the range from 0.1 to 15 μM, and the limit of detection was 12 nM. Interferential experiments adequately testified that the proposed sensors of pH and Cd²⁺ were practicable in real samples and complex systems. In comparison with conventional analytical techniques, the ratiometric PL method was simple, rapid, economic and highly selective.     

Signal-on bimodal sensing glucose based on enzyme product-etching MnO_2 nanosheets for detachment of MoS_2 quantum dots

The sensitive and rapid detection of blood glucose is very important for monitoring and managing diabetes.Herein,a fluorescent/magnetic bimodal sensing strategy is proposed for glucose detection using a multifunction-responsive nanocomposite(MoS_2 QDs-MnO_2 NS).MoS_2 QDs act as fluorescent probes,and MnO_2 nanosheets are used as both quenchers and recognizers in this sensing platform.In the presence of glucose-mediated enzyme product(H_2 O_2),MnO_2 nanosheet is etched,thus releasing MoS_2 QDs and Mn~(2+)ions,which causes the significantly enhancement of fluorescent and magnetic signals.Furthermore,MoS_2 QDs-MnO_2 NS-based fluorescent test paper is constructed for H_2 O_2 sensing with the naked eyes.Under optimal conditions,the dual linear ranges of 20-300 μmol/L and 40-250 μmol/L toward glucose detection are obtained for the fluorescent and magnetic mode,respectively.Furthermore,this bimodal assay exhibits good reproducibility and acceptable accuracy in glucose detection of clinical samples,demonstrating great versatility and flexibility of multifunctional probes in glucose detection.     

Synthesis of Multifunctional Mn‐Doped CdTe/ZnS Core/Shell Quantum Dots

The synthesis of a novel water‐soluble Mn‐doped CdTe/ZnS core‐shell quantum dots using a proposed ultrasonic assistant method and 3‐mercaptopropionic acid (MPA) as stabilizer is descried. To obtain a high luminescent intensity, post‐preparative treatments, including the pH value, reaction temperature, reflux time and atmosphere, have been investigated. For an excellent fluorescence of Mn‐doped CdTe/ZnS, the optimal conditions were pH 11, reflux temperature 100°C and reflux time 3 h under N₂ atmosphere. While for phosphorescent Mn‐doped CdTe/ZnS QDs, the synthesis at pH 11, reflux temperature 100°C and reflux time 3 h under air atmosphere gave the best strong phosphorescence. The characterizations of Mn‐doped CdTe/ZnS QDs were also identified using AFM, IR, powder XRD and thermogravimetric analysis. The data indicated that the photochemical stability and the photoluminescence of CdTe QDs are greatly enhanced by the outer inorganic ZnS shell, and the doping Mn²⁺ ions in the as‐prepared quantum dots contribute to strong luminescence. The strong luminescence of Mn‐doped CdTe/ZnS QDs reflected that Mn ions act as recombination centers for the excited electron‐hole pairs, attributing to the transition from the triplet state (⁴T₁) to the ground state (⁶A₁) of the Mn²⁺ ions. All the experiments demonstrated that the surface states played important roles in the optical properties of Mn‐doped CdTe/ZnS core‐shell quantum dots.     

Resonance Raman spectroscopy as a probe of the crystallite size of MoS2 nanoparticles

Irregularly shaped and inorganic fullerene-like MoS₂ compounds were characterized by Resonance Raman spectroscopy using an exciting line at 633 nm. It was shown that the relative intensity of the longitudinal acoustic mode at 226 cm⁻¹ and its overtone strongly depends on the MoS₂ crystallite size but not on the size of the particles made of agglomerated crystallites. This technique appeared as a promising probe to characterize in situ very small crystallites that are not observed by XRD.     

A potential visual fluorescence probe for ultratrace arsenic (III) detection by using glutathione-capped CdTe quantum dots

The interaction between mercaptoacetic acid (MA)-capped CdTe QDs, MA-capped CdTe/ZnS QDs or glutathione (GSH)-capped CdTe QDs with As(III) was studied using fluorescence spectrometry. As (III) has a high-affinity to reduced-GSH to form As(SG)₃, and the emission of the GSH-capped CdTe QDs (λ_em. = 612 nm) is quenched effectively. Thus, a novel fluorescence spectrometric method was developed for As (III) determination by using GSH-CdTe QDs. Under optimal conditions, the quenched fluorescence intensity (F₀/F) increased linearly with the concentration of As (III) ranging from 5.0 × 10⁻⁶ to 25 × 10⁻⁵ mol L⁻¹. The limit of detection (3σ) for As (III) was found to be 2 × 10⁻⁸ mol L⁻¹. This method is potentially useful in visual detection of As (III) under irradiation of the ultraviolet light.     

Three-dimensional porous reduced graphene oxide decorated with MoS2 quantum dots for electrochemical determination of hydrogen peroxide

Three-dimensional (3D) graphene-based nanomaterials have shown wide applications in electrochemical fields such as biosensors. In this study, we displayed a simple fabrication of 3D structural reduced graphene oxide (3D structural RGO) decorated with molybdenum disulfide quantum dots (MoS₂QDs) through a three-step reaction process. With its abundant raw materials, this strategy is economic and non-toxic. Various characterization techniques were utilized to characterize the morphologies of the synthesized MoS₂QDs, graphene oxide (GO), and 3D structural RGO-MoS₂QDs composites. Simultaneously, X-ray photoelectron spectroscopy was applied to characterize the structure and properties of composites. In order to understand the effects of the reaction period on the structure of 3D structural RGO-MoS₂QDs, a series of samples with various reaction periods were prepared for morphological characterization. Finally, the fabricated 3D structural RGO-MoS₂QDs composites were used to modify a glassy carbon electrode as an electrochemical non-enzymatic hydrogen peroxide (H₂O₂) sensor. The obtained results indicate that the fabricated electrochemical H₂O₂ sensor exhibits a wide detection range (0.01–5.57 mM), low detection limit (1.90 μM), good anti-interference performance, and long-time stability (18 days).     

Ratiometric Fluorescent Paper-Based Sensor Based on CdTe Quantum Dots and Graphite Carbon Nitride Hybrid for Visual and Rapid Determination of Cu2+ in Drinks

A simple and effective ratiometric fluorescence sensor of CdTe QDs/GCNNs for on-site and rapid analysis of Cu²⁺ has been established by mixing physically CdTe QDs and graphite carbon nitride (GCNNs). Two emissions peaks of CdTe QDs at 572 nm and GCNNs at 436 nm are both excitated at 340 nm. Under a UV lamp, fluorescent of traffic yellow CdTe QDs is linearly quenched by Cu²⁺ (as the detection signal), while blue GCNNs remains unchanged (as the reference), resulting in a distinguishable color change gradually from pink yellow to blue. The limit of detection (LOD) of this new sensor for Cu²⁺ is as low as 0.47 ng mL⁻¹ with 1.4 % RSD. The established method has been successfully applied to detection of Cu²⁺ in various drinks with satisfactory results. Moreover, a paper-based sensor, which has been prepared by soaking cellulose acetate membrane in CdTe QDs/GCNNs sensor solution, has a wide semiquantitative detection range for Cu²⁺ (0.01 ~ 5.0 μg mL⁻¹). It has realized successfully on-site and rapid determination of Cu²⁺ in red wine without any pretreatment procedure and is of great promotion and application value in determination of Cu²⁺ in liquid samples.     

An ultrasensitive electrochemical immunosensor for CA72-4 based on a signal amplification strategy of MoS2 nanoflower-supported Au nanoparticles

Accurate detection of cancer antigen 72-4 (CA72-4), a tumor-associated glycoprotein, is of great significance for gastric cancer diagnosis and immunotherapy monitoring. Modification of noble metal nanoparticles on transition metal dichalcogenides can significantly enhance functions, such as electron transport. Molybdenum disulfide gold nanoparticles nanocomposites (MoS₂-Au NPs) were prepared in this study and a series of characterization studies were carried out. In addition, a label-free, highly sensitive electrochemical immunosensor molybdenum disulfide -Au nanoparticles/Glassy carbon electrode (MoS₂-Au NPs/GCE) was also prepared and used for the detection of CA72-4. The electrochemical performance of the immunosensor was characterized by electrochemical techniques, such as cyclic voltammetry (CV), differential pulse voltammetry (DPV), and electrochemical impedance spectroscopy (EIS). The results indicated that better MoS₂-Au NPs nanomaterials have been synthesized, and the prepared electrochemical immunosensor, MoS₂-Au NPs/GCE, showed excellent electrochemical performance. The sensor exhibited high detection sensitivity under optimal conditions, including an incubation time of 30 min, an incubation temperature of 25 °C, and a pH of 7.0. The electrochemical immunosensor also had a low detection limit of 2.0 × 10^?5 U/mL (S/N = 3) in a concentration range of 0.001–200 U/mL, with good selectivity, stability, and repeatability. In conclusion, this study provided a theoretical basis for the highly sensitive detection of tumor markers in clinical biological samples.     

Novel β-cyclodextrin modified quantum dots as fluorescent probes for polycyclic aromatic hydrocarbons （PAHs）

Water-soluble CdSe/ZnS quantum dots （QDs） were prepared via a simple sonochemical procedure using β-cyclodextrin （CD） as surface coating agent. The QDs displayed a sensitive emission enhancement for anthracene over other related polycyclic aromatic hydrocarbons, and the detection limit was around 1.6 × 10^-8 mol/L.     

One-pot synthesis of strongly fluorescent DNA-CuInS2 quantum dots for label-free and ultrasensitive detection of anthrax lethal factor DNA

Herein, high quality DNA-CuInS₂ QDs are facilely synthesized through a one-pot hydrothermal method with fluorescence quantum yield as high as 23.4%, and the strongly fluorescent DNA-CuInS₂ QDs have been utilized as a novel fluorescent biosensor for label-free and ultrasensitive detection of anthrax lethal factor DNA. L-Cysteine (L-Cys) and a specific-sequence DNA are used as co-ligands to stabilize the CuInS₂ QDs. The specific-sequence DNA consists of two domains: phosphorothiolates domain (sulfur-containing variants of the usual phosphodiester backbone) controls the nanocrystal passivation and serves as a ligand, and the functional domain (non-phosphorothioates) controls the biorecognition. The as-prepared DNA-CuInS₂ QDs have high stability, good water-solubility and low toxicity. Under the optimized conditions, a linear correlation was established between the fluorescence intensity ratio I/I₀ (I₀ is the original fluorescence intensity of DNA-CuInS₂ QDs, and I is the fluorescence intensity of DNA-CuInS₂ QDs/GO with the addition of various concentrations of anthrax lethal factor DNA) and the concentration of anthrax lethal factor DNA in the range of 0.029–0.733 nmol L⁻¹ with a detection limit of 0.013 nmol L⁻¹. The proposed method has been successfully applied to the determination of anthrax lethal factor DNA sequence in human serum samples with satisfactory results. Because of low toxicity and fine biocompatibility, DNA-CuInS₂ QDs also hold potential applications in bioimaging.     

Sensing during In Situ Growth of Mn‐Doped ZnS QDs: A Phosphorescent Sensor for Detection of H2S in Biological Samples

Monitoring the in situ growth of Mn‐doped ZnS quantum dots is shown to be a route to selectively detect H₂S, an important endogenously produced signalling molecule. The use of Mn²⁺ as a dopant resulted in orange phosphorescence, making it possible to avoid the background fluorescence from biological surroundings that can occur at other wavelengths. The choice of ZnS QDs as the host material ensured selectivity, since only sulfide can precipitate Zn²⁺ and Mn²⁺ from aqueous solution.     

ZnS quantum dots derived a reagentless uric acid biosensor

A reagentless amperometric uric acid biosensor based on zinc sulfide (ZnS) quantum dots (QDs) was firstly developed. It could detect uric acid without the presence of an electron mediator. The carboxyl group functionalized ZnS QDs were synthesized, and they were soluble biocompatible and conductive. ZnS QDs conjugates could provide increased enzyme binding sites, which may result in higher enzyme loading. Thus, the proposed uricase/ZnS QDs/l-cys biosensor exhibited higher amperometric response compared to the one without QDs (uricase/l-cys biosensor). In addition, there was little AA interference. It showed a linear dependence on the uric acid concentration ranging from 5.0 × 10⁻⁶ to 2.0 × 10⁻³ mol L⁻¹ with a detection limit of 2.0 × 10⁻⁶ mol L⁻¹ at 3σ.     

Immuno-capture and in situ detection of Salmonella typhimurium on a novel microfluidic chip

The new method presented in this article achieved the goal of capturing Salmonella typhimurium via immunoreaction and rapid in situ detection of the CdSe/ZnS quantum dots (QDs) labeled S. typhimurium by self-assembly light-emitting diode-induced fluorescence detection (LIF) microsystem on a specially designed multichannel microfluidic chip. CdSe/ZnS QDs were used as fluorescent markers improving detection sensitivity. The microfluidic chip developed in this study was composed of 12 sample channels, 3 mixing zones, and 6 immune reaction zones, which also acted as fluorescence detection zones. QDs–IgG–primary antibody complexes were generated by mixing CdSe/ZnS QDs conjugated secondary antibody (QDs–IgG) and S. typhimurium antibody (primary antibody) in mixing zones. Then, the complexes went into immune reaction zones to label previously captured S. typhimurium in the sandwich mode. The capture rate of S. typhimurium in each detection zone was up to 70%. The enriched QDs-labeled S. typhimurium was detected using a self-assembly LIF microsystem. A good linear relationship was obtained in the range from 3.7 × 10 to 3.7 × 10⁵ cfu mL⁻¹ using the equation I = 0.1739 log (C) − 0.1889 with R² = 0.9907, and the detection limit was down to 37 cfu mL⁻¹. The proposed method of online immunolabeling with QDs for in situ fluorescence detection on the designed multichannel microfluidic chip had been successfully used to detect S. typhimurium in pork sample, and it has shown potential advantages in practice.     

In situ X-ray absorption and diffraction studies of carbon coated LiFe1/4Mn1/4Co1/4Ni1/4PO4 cathode during first charge

Synchrotron based in situ X-ray absorption spectroscopy (XAS) and X-ray diffraction (XRD) techniques are used to study electronic and crystal structure changes of the carbon coated LiFe_1/4Mn_1/4Co_1/4Ni_1/4PO₄ (LiFe_1/4Mn_1/4Co_1/4Ni_1/4PO₄/C) cathode material for Li-ion batteries during the first charge. In situ Fe, Mn, Co and Ni K-edge XAS results revealed that the three voltage plateaus at ～3.6, 4.2 and 4.7 V vs. Li/Li⁺ are attributed to the redox reactions of Fe²⁺/Fe³⁺, Mn²⁺/Mn³⁺ and Co²⁺/Co³⁺, respectively, while the apparent capacities above 4.9 V is not originated from the Ni²⁺/Ni³⁺ redox, but very likely from the electrolyte decomposition. Interesting phase transition behaviors of LiFe_1/4Mn_1/4Co_1/4Ni_1/4PO₄/C were observed with the formation of an intermediate phase and the solid solution regions. Combined in situ XAS and XRD techniques indicate fast electronic structural changes and slow bulk crystal structural changes.     

Dual-functional photocatalysis boosted by electrostatic assembly of porphyrinic metal-organic framework heterojunction composites with CdS quantum dots

Photocatalytic dual-functional reaction under visible light irradiation represents a sustainable development strategy. In detail, H₂ production coupled with benzylamine oxidation can remarkably lower the cost by replacing sacrificial agents. In this work, Cd S quantum dots(Cd S QDs) were successfully loaded onto the surface of a porphyrinic metal-organic framework(Pd-PCN-222) by the electrostatic selfassembly at room temperature. The consequent Pd-PCN-222/CdS heterojunction composites...     

In situ formation of p–n junction: A novel principle for photoelectrochemical sensor and its application for mercury(II) ion detection

The discovery and development of photoelectrochemical sensors with novel principles are of great significance to realize sensitive and low-cost detection. In this paper, a new photoelectrochemial sensor based on the in situ formation of p–n junction was designed and used for the accurate determination of mercury(II) ions. Cysteine-capped ZnS quantum dots (QDs) was assembled on the surface of indium tin oxide (ITO) electrode based on the electrostatic interaction between Poly(diallyldimethylammonium chloride) (PDDA) and Cys-capped ZnS QDs. The in situ formation of HgS, a p-type semiconductor, on the surface of ZnS facilitated the charge carrier transport and promoted electron-hole separation, triggered an obviously enhanced anodic photocurrent of Cys-capped ZnS QDs. The formation of p–n junction was confirmed by P–N conductive type discriminator measurements and current–voltage (I–V) curves. The photoelectrochemical method was used for the sensing of trace mercuric (II) ions with a linear concentration of 0.01 to 10.0 µM and a detection limit of 4.6 × 10⁻⁹ mol/L. It is expected that the present study can serve as a foundation to the application of p–n heterojunction to photoelectrochemical sensors and it might be easily extended to more exciting sensing systems by photoelectrochemistry.