Recovery of thermal and mechanical properties after thermal treatment in a polyester-based polyurethane

Solution casted films of segmented polyurethanes based on poly (ethylene adipate) glycol, 4,4diphenylmethanediisocyanate, and 1,4 butanediol were studied by thermal-mechanical methods including differential scanning calorimetry and mechanical hysteresis. Data demonstrate that, following thermal treatment at 70 °C for 15 min, these polymers show time-dependent thermal and mechanical properties. In fact, because 70 °C is a temperature greater than the melting point of soft segments (about 42 °C), the soft-segment crystals are melted and their crystallization is time dependent. The results are explained in terms of phase separation. In particular, the sample with better phase separation has a faster and larger recovery.     

Study of crystallization kinetics of trans-1,4-polyisoprene

The concentrations and the growth rates of high- and low-melting type spherulites of trans-1,4-polyisoprene were measured in the temperature range 39–49°C. It was shown that above about 40°C., the crystallization rate of trans-1,4-polyisoprene is determined primarily by the radial growth rate of high-melting form (HMF) spherulites, whereas the predominance of the low-melting form (LMF) crystals below 40°C. can be attributed to the high rate of formation of LMF primary nuclei at lower crystallization temperatures. Temperature-independent rate parameters were calculated from optical and dilatometric measurements and were found to be in good agreement. Both the change in nucleation habit and spherulite growth rate with temperature can be explained on the basis of a lower end surface free energy of LMF crystals of trans-1,4-polyisoprene compared to that of the HMF crystals.     

Kinetics of nonisothermal crystallization and melting of normal high density and ultra-high molecular weight polyethylene blends

The kinetics of nonisothermal crystallization and melting of blends of ultra-high molecular weight polyethylene (UHMWPE) and polyethylene high density with normal molecular weight (NMWPE) are investigated by means of differential scanning calorimetry (DSC). Mixing the components at a temperature below the flow temperature of UHMWPE (215 °C) results in increased crystallization/melting rates of the individual components in the blends above the corresponding additive values. The morphological observations of the blends, carried out by means of polarization microscopy, show that a strong boundary of both types of structures (UHMWPE non-flowing aggregates and NMWPE spherulite structures) does not exist. The NMWPE spherulites' dimensions decrease on increasing the UHMWPE concentration in the blends, but their number increases. The facilitation of the crystallization/melting of the components in the blends is explained in terms of mutual influence exhibited by the components with respect to each other. It is due to the inner stresses in nonflowing UHMWPE characterized with a lot of entangled tie molecules and to the partial co-crystallization of NMWPE molecules with the flowing part of UHMWPE. At mixing temperatures above 215 °C the melting/crystallization integral kinetic curves have only one linear part in contrast to these of the same blend (11 ratio of components), prepared at 190 °C. The rates of melting/crystallization remain almost constant with the increase of the mixing temperatures.     

Thermochromism of polypropylene gels

It is found that polypropylene gels in some solvents of benzene-derivatives show a striking change of colour. The colour changes from blue to yellow as the temperature rises from the melting point of the solvent to around 70–80 °C. The apparent characteristic of the phenomenon resembles the thermochromism of cholesteric liquid crystals although polypropylene itself is colourless and has no asymmetric carbons in the molecules. Polypropylene flakes swelled in these solvents also show similar thermochromism.     

Preparation of muscovite with ultrahigh specific surface area by chemical cleavage

The specific surface area of a muscovite sample increases drastically after exposure to a LiNO₃ solution, e.g., from 3.4 m²/g, corresponding to platelets of ca. 200 silicate layers, to 295 m²/g (platelets of ca. 2–3 silicate layers) after treatment at 180°C under atmospheric pressure for 46 h. The efficiency of the cleavage process decreases with decreasing temperature (down to 50°C). The LiNO₃/H₂O weight ratio is also very important: at 130°C and a reaction time of 46 h, for instance, a value in the range of 1.7–1.8 leads to the highest specific surfaces. The cleaved products have the form of strong papers that disperse readily in water. During the cleaving procedure, not only the particle thickness, but also the diameter decreases. There is no evidence of damage or partial dissolution of the silicate structure after cleavage, by IR spectroscopy and yield. The use of LiCl also leads to an increase in specific surface area, but the effect is weaker than in the case of LiNO₃. Treatment with some other alkaline and alkaline earth nitrates and chlorides did not increase the specific surface area of muscovite significantly.     

On the theory of melting polymer crystals

On the basis of the intermolecular potentials data structural phase transitions in polymer crystals (polyethylene) are described. By using the meanfield approximation, the theories of premelting transitions for paraffin crystals and conformational melting of polyethylene crystals were developed. The dependence of temperatures of such transitions upon chain length was calculated and rather good agreement with experimental data was shown.Dedicated to Prof. Dr. W. Pechhold on the occasion of his 60th birthday     

Spreading and compression of n-hexadecyl acrylate at liquid-air interface

Usingn-hexadecyl acrylate, surface pressure-area (F-A) curves and equilibrium spreading pressuresF ^e were measured at various temperatures (5.7°–46°C) by the Langmuir balance (F-A) and the Wilhelmy-plate method (F ^e). At low temperatures (T<13 °C) condensed films and the liquid-condensed/solid condensed transition can be observed. At high temperatures (T>30 °C) liquid-expanded films occur. In the intermediate range the compression curves have two transition points. The transition pressureF ₁ between liquid-expanded and condensed film has a marked temperature dependence. The transition enthalpiesH ₁ decrease with increasing temperature and become zero at 29.2 °C. The second transition is related to a transition between the condensed films (F ₂). The slight temperature dependence of this transition is accompanied by an increasing change of area as well as by increasing transition enthalpiesH ₂.TheF ^e-T curve has two distinct breaks, at the melting pointT _m and atT=30 °C. The break atT _m is due to the melting process and the break atT=30 °C is caused by a phase transition between a liquid-expanded film and a condensed film.The phase diagram was constructed from the transition pressures. It can be demonstrated that the highest pressures of the thermodynamic stable film occurs atT _m. At temperaturesT>T _m equilibrium spreading pressure and equilibrium collapse pressure are identical whereas atT _m supercompression of the monolayer occurs. The film in this state behaves like a supercooled liquid. Obviously, rupture and collapse of such a film lead to a thermodynamically metastable bulk phase.     

2,5-Dichloro-1-(ROSO2)benzene [R = C6H5, C6F5, and CH2(CF2)4H]: Synthesis, molecular structure, and solubility in supercritical CO2

Highly crystalline phenyl 2,5-dichlorobenzenesulfonate (PDBS, T_melt = 86-87 °C) and pentafluorophenyl 2,5-dichlorobenzenesulfonate (FPDBS, T_melt = 120-122 °C) were synthesized. Single-crystal X-ray molecular structure determinations show that both compounds have similar three-dimensional molecular structures; however, PDBS crystals are thin platelets and FPDBS crystals form hexagonal tube-like structures that are predominately hollow at one end. PDBS crystals exhibit offset π-stacking of the phenoxy-rings that form complete two-dimensional layers each two molecules thick. Hydrogen-bonding interactions are calculated at ∼3.2 Å between the C6-hydrogen and the sulfonyl-oxygen of a neighboring molecule. On the other hand, for FPDBS, π-stacking of the dichloro-substituted ring as well as dipole-dipole interactions of the fluorinated-phenoxy rings appears to be the predominate intermolecular interactions. Neither structure exhibits any kind of side-on interaction of the phenyl rings. PDBS and FPDBS exhibit melting point depressions of 26 and 40 °C, respectively, in the presence of supercritical CO₂. Although both sulfonates exhibit high solubility in CO₂, much lower pressures are needed to dissolve FPDBS compared to PDBS. For example, at 100 °C FPDBS dissolves at 4750 psia and PDBS dissolves at 11,000 psia. The solubility data reinforce the observation that fluorinating a compound can significantly lower the conditions needed to dissolve that compound in CO₂.     

Formation of uniform particles of cobalt compounds and cobalt

Depending on experimental conditions, precipitation from cobalt (II) sulfate solutions in the presence of urea yields finely dispersed cobalt compounds of different chemical compositions and morphologies. The needle-type particles, generated in closed systems, were identified as cobalt (II) basic carbonate. In systems open to air, spherical particles of cobalt (II) basic cyanato carbonate are formed. The latter transform to spherical Co₃O₄ particles on calcining at 300°C, and then can be reduced to metallic cobalt powder by reacting with hydrogen at 300°C. In the presence of sodium dodecylsulfate, unique cone-type particles containing dodecylsulfate ions are produced.Supported in part by the Air Force Contract F49620-85-C-0142.     

Thermally stimulated currents in poly(bis(p-fluorophenoxy)phosphazene)

Thermally stimulated currents (TSC) were examined for poly(bis(p-fluorophenoxy)phosphazene) (PBFPP) film. TSC showed peaks at the glass transition temperature (Tg=–4 °C) and atT(1) (160 °C – 170 °C), where-form crystal phase transformed to mesophase of-form structure. Another peak was found atT _cc betweenTg andT(1). Linear relationship between polarization field and peak current ofT _cc -peak was found, which shows thatT _cc -peak was caused by motion of dipolar groups in crystalline phase. When heating (up to 200 °C) and cooling (down to 20 °C) thermal process was repeated,T _cc -peak shifted to higher temperature region approachingT(1) and simultaneously, the peak current ofT(1)-peak became smaller. Activation energy, time constant of dipolar relaxation and charge mobility were evaluated forT _cc -peak. From these results, it was concluded that-form and more ordered- form crystalline phases coexisted in PBFPP once heated aboveT(1) and the content of- form phase increased by repeated thermal hysteresis.     

Thermoanalytical investigations of extended and annealed keratins

DSC investigations have been used to characterize the microfibril-matrix complex of keratin consisting of helical low-sulfur microfibrils in a nonhelical high-sulfur matrix. The corresponding DSC curves display one or two endothermic peaks in the temperature range 230°–255°C. The first peak is a microfibrillar peak and the second one a matrix peak (cystine decomposition peak). DSC investigations of extended keratins have shown that the microfibrillar peak is a helix peak. DSC investigations of annealed keratins confirm our earlier assumption that the helix peak is no helix melting peak but an irreversible helix unfolding, superimposed by various decomposition reactions. The matrix peak of the above described keratin samples is less reproducible than the corresponding helix peak and cannot be used for further characterization studies of keratins.Dedicated to Professor E. G. Klesper on the occasion of his 60th birthday.     

Pecularities of the thermomechanical behaviour of ultra-high molecular weight linear polyethylene and its blends with linear polyethylene of normal molecular weight

Ultra-high molecular weight polyethylene UHMWPE (M _w=4 · 10⁶,I _s=O g/ 10 min), high density polyethylene of normal molecular weight NMWPE (I _s= 4.8 g/10 min) and their blends have been investigated by means of thermomechanical loading in constant and impulse regime. It has been established that after melting, NMWPE passes to a viscous-liquid state. After melting at 138 °C UHMWPE passes to a high-elastic state. The transition of UHMWPE to a viscous-liquid state takes place at temperatures higher than 180 °C and is accompanied by a high-elastic reversible deformation. The blends of UHMWPE with 10 and 20 mass % of NMWPE show a plateau on the thermomechanical curves, corresponding to a high-elastic state, in a shorter temperature range where the deformation is greater. The blends containing the higher percent of NMWPE show thermomechanical curves lacking such a plateau. All blends are characterized by a singular thermomechanically defined temperature of melting, which increases with increase of UHMWPE content. The existence of the high-elastic state in the curves of UHMWPE and its blends containing NMWPE less than 30 mass % above their melting temperatures is explained by the high degree of physical crosslinking of UHMWPE.     

Temperature-dependence of mechanical and morphological properties of ultra-high molecular weight polyethylene cross-linked by electron beam irradiation

Cross-linking of ultra-high molecular weight polyethylene was performed with electron-beam irradiation in the range of radiation dose from 12 to 96 Mrad under nitrogen. Dry gel films and melt films were used as specimens. Two kinds of cross-linked specimens could be kept at 200°C for a prolonged time in an undeformed state and this tendency was independent of radiation dose. The elongation of the gel films hampered the heat-resistant effect and the drawn specimens were broken at temperatures lower than 175 °C. The elongation of the melt films could not be realized, because of a marked fixation of chains in the fiber network, even at a dose of 12 Mrad.     

Contact angle hysteresis in carbon fibers studied by wetting force measurements

The surface free energy of polyacrylonitrile carbon fibers was investigated by using the Wilhelmy technique. The difference in surface free energy between immersion and emersion was observed for the carbon fiber pyrolyzed at 2500 °C.In contrast, the hysteresis disappeared with repyrolyzation of the carbon fibers at 3000 °C. Auger electron spectroscopic analysis indicated that the surface of the latter carbon fiber (repyrolyzed at 3000 °C) consisted of the basal planes of graphite. Rough surface topography of the carbon fiber repyrolyzed at 3000 °C, as observed by scanning electron microscope, did not affect the hysteresis. Therefore, the contact angle hysteresis was attributed to the chemical adsorbants on the activation sites of the fiber surfaces, as detected by Auger electron spectroscopy.     

Rigid-rod polymers with flexible side chains

Modeling studies were performed for a rigid-rod polyester with hexadecyloxy side chains (n=16) in order to simulate x-ray scattering curves in the medium angle scattering region (s=4 sin / from 0.2 Å^–1 to 2.2 Å^=t–1). The experimental ones were taken from a material obtained by cooling to room temeperature from the smectic mesophase at 150°C. The wide-angle x-ray diffractograms were calculated for given conformations and molecular arrangements using Debye's equation. The theoretical result thus obtained for a great variety of possible packing models and structures was compared to the experimental result. The size of the effective scattering region is found to be 61×18×52=6×10⁴ ų and consists of approximately five layers, each of which is composed of two rigid rods and 20 side chains. The planes form by the rigid rods, together with the side chains, have a distance of 3.6 Å, the distance between the rods being 26 Å. As the main result, it was found that the side chains form regions with a denser ordering (clustering). The interchain distance for side chains decreases in the regions from 5.3 Å to 4.8 Å.     

Adhesive effect of high density polyethylene gels on polyethylene moldings

Adhesive effect of polyethylene moldings by use of high density polyethylene gels in organic solvents such as decalin, tetralin, ando-dichlorobenzene was investigated by shearing tests, electron microscope, and DSC measurements. All of the gels showed such a strong adhesive strength over 36 kg/cm² that polyethylene plates of 3 mm in thickness gave rise to necking sufficient for practical use, when heated at 120 °C for 2 h. In particular, the gel in tetralin showed a strong adhesive strength when heated at 110 °C. It was found that adhesive strength increases with the heating temperature; the temperatures at which adhesive strength begins to increase differ depending on the type of polyethylene sample and solvent. It is apparent that polyethylene gels exhibit an adhesive effect when they are heated at higher temperatures than the gel melting temperatures, and that the closer the SP values of solvents used for the gelation are to the molded polyethylene, the stronger the adhesion of the polyethylene molding.     

Electrical properties of poly(bis(β-phenoxyethoxy)phosphazene) and its complexes

Electrical and dielectrical properties of poly(bis(-phenoxyethoxy)phosphazene) (I) and its complexes with various content ratios of AgSO₃CF₃ to monomeric unit (0.25/1 (II) and 0.5/1 (III) in molar ratio) were investigated.Dc conductivity of respective samples at 18 °C were 6.1×10^–12, 4.4×10^–9, and 7.1×10^–8 S/m.Dc conduction was considered to be due to ion hopping. Charge mobility ranged from 3×10^–12 to 6× 10^–11 m²/Vs depending on the applied field in sample II. In sample I, a tan peak was found which can be ascribed to molecular relaxation of main chains. The peak vanished upon introducing AgSO₃ CF₃. Temperature dependence of total conductivity ( _T ) measured byac method in the temperature range between –150 °C and 50 °C showed several peaks at the temperatures corresponding to the peak temperatures of tan. Total conductivities of respective samples at 100 kHz were 4.9×10^–7 (69 °C), 1.7×10^–4 (45 °C), and 1.5×10^–4(40°C)S/m.     

Growth of polyethylene single crystals from the melt: change in lateral habit and regime I–II transition

Using the technique of extraction, single crystals have been obtained from polyethylene fractions isothermally crystallized from the melt at atmospheric pressure. It has been found that the lateral habit of single crystals changes in the vicinity of the transition temperature of growth regime (regime I–II): lenticular shape elongated in the direction of theb axis (type A) in the range of regime I and truncated lozenge with curved edges of {200} and {110} growth faces (type B) in that of regime II. The transition of lateral habit causes a drastic change in the width of {110} growth faces; {110} growth faces are well developed in type B crystals while they cannot be observed and must be very small in type-A crystals. It has been shown that the growth regime of the small {110} growth face of type-A crystals must be in regime I; hence the regime I–II transition can be explained as the result of this change in lateral habit (width of the {110} growth face).     

Electrically conducting,thermally stable,and mechanically strong CuS-poly(parabanic acid) composite films and their shielding effect of electromagnetic wave

Poly(parabanic acid)-CuS composite film (wt-% of CuS=20–50) prepared by using organosol of CuS (=1500 Å) showed electrical conductivity of 0.1–70 S cm^–1, high thermal stability up to 250°C, high mechanical strength (breaking stress=7.0–12 × 10⁷ Pa), and good shielding effect of electromagnetic wave.     

Melting temperature of colloidal crystals of monodisperse silica spheres in ethanol-water and ethylene glycol-water mixtures

The melting temperature (T _m) of colloidal crystals of monodisperse silica spheres in ethanol-water and ethylene glycol-water suspensions has been measured by reflection spectroscopy. A sphere of 110 nm in diameter and 0.041 in monodispersity index is used after purification and deionization processes. Transformation from the body-centered cubic lattice to the face-centered cubic lattice subphases is observed as the suspension temperature rises, which is similar to the purely aqueous suspension of the same sphere. A phase diagram including liquid-like and crystal-like structures is obtained in the presence of ion-exchange resins coexisted. The data ofT _m are analyzed successfully with the theory of Williams, Crandall, and Wojtowicz. The heat of melting decreases by the addition of ethanol or ethylene glycol in the mixtures.