Improvement of abrasion resistance in artificial seawater and corrosion resistance in NaCl solution of 7075 aluminum alloy processed by laser shock peening

As 7075 aluminum alloy is widely used in a humid environment, in order to enhance its abrasion resistance and electrochemical corrosion resistance, the paper studied the effect of laser shock peening on abrasion resistance in artificial seawater and corrosion resistance in 3.5% NaCl solution of 7075 aluminum alloy. Result shows that when specimens were treated once and twice with 7.17 GW/cm² the abrasion loss would be reduced by 43.75% and 46.09% compare to untreated respectively, and the corrosion rate of 7075 aluminum alloy could be reduced as much as 50.32% by LSP treatment with 7.17 GW/cm². What’s more, the effects on the microhardness, microstructure and residual stress with different LSP impacts and power density were investigated to find out strengthening mechanism of laser shock peening, which were observed and measured by microhardness tester, optical microscope and X-ray diffraction (XRD) residual stress tester. In the entire laboratory tests, it is considered that LSP is a practical option to improve abrasion resistance in seawater and corrosion resistance of 7075 aluminum alloy.     

LY2铝合金激光冲击处理工艺

为了提高LY2铝合金疲劳寿命,探索了用激光冲击强化方法处理LY2铝合金的技术。使用流水约束层和铝箔涂层,利用波长为532 nm,脉宽为10 ns,能量为5 J,光斑直径为3 mm的YAG激光器对LY2试样进行了激光冲击强化处理。结果表明:经激光冲击强化后LY2铝合金疲劳寿命提高1.1倍。对激光冲击强化后的试件断口分析结果表明激光冲击的强化作用抑制了裂纹在试件表层的萌生和扩展,从而提高了材料的疲劳寿命。     

Effect of laser shot peening on precipitation hardened aluminum alloy 6061-T6 using low energy laser

Mechanical properties of engineering material can be improved by introducing compressive residual stress on the material surface and refinement of their microstructure. Variety of mechanical process such as shot peening, water jet peening, ultrasonic peening, laser shot peening were developed in the last decades on this contrast. Among these, lasers shot peening emerged as a novel industrial treatment to improve the crack resistance of turbine blades and the stress corrosion cracking (SCC) of austenic stainless steel in power plants. In this study we successfully performed laser shot peening on precipitation hardened aluminum alloy 6061-T6 with low energy (300 mJ, 1064 nm) Nd:YAG laser using different pulse densities of 22 pulses/mm² and 32 pulses/mm². Residual stress evaluation based on X-ray diffraction sin² ψ method indicates a maximum of 190% percentage increase on surface compressive stress. Depth profile of micro-hardness shows the impact of laser generated shock wave up to 1.2 mm from the surface. Apart from that, the crystalline size and micro-strain on the laser shot peened surfaces have been investigated and compared with the unpeened surface using X-ray diffraction in conjunction with line broadening analysis through the Williamson-Hall plot.     

不锈钢焊接件不等强度激光冲击与应力腐蚀试验研究

针对不锈钢焊接接头应力及组织分布不均匀,容易导致应力腐蚀开裂的问题,采用不等强度激光冲击波对316奥氏体不锈钢焊接接头进行处理。通过应力腐蚀试验、残余应力测试及微观组织分析,研究了激光冲击强化对焊接接头应力腐蚀抗性的影响及其作用机理。试验结果表明:激光冲击强化将焊接件的应力腐蚀断裂时间提高了33.48%。激光冲击波的作用,在焊接接头部位引入了高数值的残余压应力,一方面消除了热影响导致的残余拉应力,同时抵消了拉伸工作载荷的作用,降低局部应力梯度,从而延缓表面钝化膜的破裂;另一方面,激光冲击使焊接接头不同区域之间的微观组织均匀和细化,提高了微裂纹萌生的条件,降低了金属发生阳极溶解的可能性。两种因素的共同作用,使得不锈钢焊接接头的抗应力腐蚀性能显著增强。     

Effect of shot peening on the microstructure of laser hardened 17-4PH

In order to investigate the influence of shot peening on microstructure of laser hardened steel and clarify how much influence of initial microstructure induced by laser hardening treatment on final microstructure of laser hardened steel after shot peening treatment, measurements of retained austenite, measurements of microhardness and microstructural analysis were carried out on three typical areas including laser hardened area, transitional area and matrix area of laser hardened 17-4PH steel. The results showed that shot peening was an efficient cold working method to eliminate the retained austenite on the surface of laser hardened samples. The surface hardness increased dramatically when shot peening treatments were carried out. The analyses of microstructure of laser hardened 17-4PH after shot peening treatment were carried out in matrix area and laser hardened area via Voigt method. With the increasing peening intensity, the influence depth of shot peening on hardness and microstructure increased but the surface hardness and microstructure did not change when certain peening intensity was reached. Influence depth of shot peening on hardness was larger than influence depth of shot peening on microstructure due to the kinetic energy loss along the depth during shot peening treatment. From the microstructural result, it can be shown that the shot peening treatment can influence the domain size and microstrain of treated samples but laser hardening treatment can only influence the microstrain of treated samples.     

Investigation of surface acoustic waves in laser shock peened metals

Laser shock peening is a well-known method for extending the fatigue life of metal components by introducing near-surface compressive residual stress. The surface acoustic waves (SAWs) are dispersive when the near-surface properties of materials are changed. So the near-surface properties (such as the thickness of hardened layers, elastic properties, residual stresses, etc.) can be analyzed by the phase velocity dispersion. To study the propagation of SAWs in metal samples after peening, a more reasonable experimental method of broadband excitation and reception is introduced. The ultrasonic signals are excited by laser and received by polyvinylindene fluoride (PVDF) transducer. The SAW signals in aluminum alloy materials with different impact times by laser shock peening are detected. Signal spectrum and phase velocity dispersion curves of SAWs are analyzed. Moreover, reasons for dispersion are discussed.     

微激光冲击DZ17G合金的表面完整性影响研究

为了在不影响柱状晶组织的前提下改善DZ17G定向凝固合金的力学性能,采用微激光冲击强化方法进行表面处理,通过X射线衍射、扫描电子显微镜、透射电子显微镜和显微硬度计,测试分析微激光冲击对DZ17G定向凝固合金表面完整性的影响。试验结果表明:在水下无吸收保护层微激光冲击处理后,合金表面发生了烧蚀、熔融,1次冲击后形成光滑熔融区,但随着冲击次数增加而形成了大量微小烧蚀孔洞和难熔颗粒;表层组织仍由和两相组成,柱状晶内形成了高密度位错和位错缠结,但未发生晶粒细化;硬度在深度上呈梯度分布,冲击1次后硬化层深度仅为100 m,表面硬度值达到503 HV,提高了22.7%,而且硬度值和硬化层深度都随着冲击次数增加而增大。     

Near-infrared absorption enhancement for perovskite solar cells via the rear grating design

Optical and Quantum Electronics - The features of laser shock peening technology was studied in relation to the physical processes occurring during and after laser treatment. The effect of laser...     

Melting of Titanium by a Shock Wave Generated by an Intense Femtosecond Laser Pulse

JETP Letters - Laser shock peening with ultrashort laser pulses has been studied by hydrodynamic and atomistic simulations, as well as experimentally. It has been shown that, in contrast to...     

Microstructure and corrosion properties of diode laser melted friction stir weld of aluminum alloy 2024 T351

Friction stir welding is a promising solid state joining process for high strength aluminum alloys. Though friction stir welding eliminates the problems of fusion welding as it is performed below melting temperature (T_m), it creates severe plastic deformation. Friction stir welds of some aluminum alloys exhibit relatively poor corrosion resistance. This research enhanced the corrosion properties of such welds through diode laser surface melting.A friction stir weld of aluminum alloy 2024 T351 was laser melted using a 1 kW diode laser. The melt-depth and microstructure were investigated using optical and scanning electron microscopy. The melt zone exhibited epitaxially grown columnar grains. At the interface between the melted and the un-melted zone, a thick planar boundary was observed. Energy dispersive spectroscopy analyzed the redistribution of elemental composition. The corrosion properties of the laser melted and native welds were studied in aqueous 0.5 M sodium chloride solution using open circuit potential and cyclic potentiodynamic polarization. The results show noticeable increase in the pit nucleation resistance (390 mV) after the laser surface treatment. The repassivation potential was nobler to the corrosion potential after the laser treatment, which confirmed that the resistance to pit growth was improved.     

Effect of an absorbent overlay on the residual stress field induced by laser shock processing on aluminum samples

Laser shock processing (LSP) or laser shock peening is a new technique for strengthening metals. This process induces a compressive residual stress field, which increases fatigue crack initiation life and reduces fatigue crack growth rate. Specimens of 6061-T6 aluminum alloy are used in this investigation. A convergent lens is used to deliver 2.5 J, 8 ns laser pulses by a Q-switch Nd:YAG laser, operating at 10 Hz. The pulses are focused to a diameter of 1.5 mm onto aluminum samples. Density of 2500 pulses/cm² with infrared (1064 nm) radiation was used. The effect of an absorbent overlay on the residual stress field using this LSP setup and this energy level is evaluated. Residual stress distribution as a function of depth is assessed by the hole drilling method. It is observed that the overlay makes the compressive residual stress profile move to the surface. This effect is explained on the basis of the vaporization of the coat layer suppressing thermal effects on the metallic substrate. The effect of coating the specimen surface before LSP treatment may have advantages on improving wear and contact fatigue properties of this aluminum alloy.     

Laser peening of aluminum alloy 7050 with fastener holes

The fatigue properties of laser peened aluminum alloy 7050 specimens with fastener holes were investigated.The surface profile and residual stress induced in the shock affected zone were characterized.Then,the fatigue specimens with notch were treated by laser peening(LP),and the fatigue lifes of LP-treated specimens were measured and compared with base materials without LP.The results indicated that LP improved the fatigue lifes of all tested specimens.The average fatigue lifes of specimens treated by LP before hole-drilling were 173% longer than those of untreated samples and had better effects than those specimens treated by LP after hole-drilling.     

Deformation-induced martensite and nanotwins by cryogenic laser shock peening of AISI 304 stainless steel and the effects on mechanical properties

Laser shock peening (LSP) of stainless steel 304 was carried out at room and cryogenic temperature (liquid nitrogen temperature). It was found that the deformation-induced martensite was generated by LSP only when the laser-generated plasma pressure is sufficiently high. Compared to room temperature laser shock peening (RT-LSP), cryogenic laser shock peening (CLSP) generates a higher volume fraction of martensite at the same laser intensity. This is due to the increase in the density of potential embryos (deformation bands) for martensite nucleation by deformation at cryogenic temperature. In addition, CLSP generates a high density of deformation twins and stacking faults. After CLSP, an innovative microstructure, characterised by networks of deformation twins, stacking faults and composite structure (martensite and austenite phases), contributes to material strength and microstructure stability improvement. The combined effect of higher surface hardness and a more stabilised microstructure results in greater fatigue performance improvement of the CLSP samples compared to that of the RT-LSP samples.     

Surface modification by oil jet peening in Al alloys, AA6063-T6 and AA6061-T4: Part 2: Surface morphology, erosion, and mass loss

Oil jet peening is a new surface treatment technique that can be potentially applied to impart compressive residual stresses in metal parts. The effect of oil jet pressure on the surface integrity and texture of metals are discussed. The surface morphology, mass loss rate, indentation, and erosion are reported. With increasing stand-off distance, the size of indents significantly decreases and reduces the average roughness in the both specimens. Results are also compared with other mechanical surface treatment process such as shot peening, laser shock peening, and water jet peening.     

Laser shock peening of steam turbine blade for enhanced service life

Fretting-fatigue is an important factor influencing service life of turbine blades. The present paper describes laser shock peening of potential crack nucleation site in the root region of steam turbine blade for its enhanced service life. The experimental study, performed with an in-house developed 2.5 J/7 ns Nd:YAG laser demonstrated that laser peening introduced a residual surface compressive stress of ?260 to ?390 MPa. Case depth of laser peened surface layer was found to be more than 900 μm.     

激光在近表面弹性性质梯度变化的材料中激发超声波的数值分析

激光激发超声波为评价材料近表面弹性性质提供了有效的手段. 考虑到由于冲击硬化、表面热处理、表面氧化等引起的金属材料近表面层弹性性质的变化，建立了一种激光在基底上的梯度材料中激发超声波的理论模型. 用有限元方法模拟了热弹条件下脉冲激光作用于材料上表面激发出的超声波及其传播过程，研究了近表面层离散的层数对超声波的产生和传播的影响，并分别讨论了表面层“变硬”和“变软”两种情况下声表面波的模式变化及用二维傅里叶变换得到各模式的色散曲线. 为进一步研究近表面层的弹性性质建立合理的计算模型及材料性质的反演提供了理论依 关键词： 超声波 有限元法 近表面弹性性质 色散     

强激光驱动爆炸与冲击效应

随着高功率密度激光技术的快速发展,强激光驱动的爆炸与冲击效应逐渐引起国内外学者的广泛关注。对强激光诱导爆炸与冲击效应研究进展进行了综述,包括强激光诱导爆炸载荷特征与相似律,强激光对材料表面冲击强化处理,强激光冲击诱导材料相变动力学行为,以及利用强激光驱动微弹道冲击等方面的研究进展,并指出了强激光诱导爆炸与冲击效应研究的发展趋势和未来需要解决的关键科学问题。     

激光冲击强化对激光增材TC4钛合金组织和抗氧化性的影响

近年来,激光增材制造技术(3D打印)成为科学研究及工业应用领域的热点。为了研究激光冲击强化对增材制造TC4钛合金性能的影响,本文采用能量为5 J,波长为1 064 nm,脉宽为10 ns,光斑直径为3 mm的脉冲激光对3D打印TC4钛合金进行激光冲击强化,分析了激光冲击强化前后材料的显微硬度、显微组织、残余应力以及高温氧化性能。结果表明,经过激光冲击强化后,材料的显微硬度比激光冲击强化前提高了8%,影响层深度达到0.4 mm,强化区域的晶粒得到细化,位错增多,并产生形变孪晶;激光冲击强化的残余压应力数值高达472 MPa,材料的高温抗氧化性能也得到改善。     

Engineering the residual stress state and microstructure of stainless steel with mechanical surface treatments

Four mechanical surface treatments have been considered for the application to austenitic stainless steel structures. Shot peening (SP), laser shock peening (LSP), ultrasonic impact treatment (UIT) and water jet cavitation peening (WJCP), also known as cavitation shotless peening (CSP), have been applied to 8 mm thick Type 304 austenitic stainless steel coupons. This study considers the merits of each of these mechanical surface treatments in terms of their effect on the surface roughness, microstructure, level of plastic work and through thickness residual stress distribution. Microstructural studies have revealed the formation of martensite close to the treated surface for each process. Residual stress measurements in the samples show compressive stresses to a significantly greater depth for the LSP, UIT and WJCP samples compared to the more conventional SP treated sample.     

High level compressive residual stresses produced in aluminum alloys by laser shock processing

Laser shock processing (LSP) has been proposed as a competitive alternative technology to classical treatments for improving fatigue and wear resistance of metals. We present a configuration and results for metal surface treatments in underwater laser irradiation at 1064 nm. A convergent lens is used to deliver 1.2 J/cm² in a 8 ns laser FWHM pulse produced by 10 Hz Q-switched Nd:YAG, two laser spot diameters were used: 0.8 and 1.5 mm.Results using pulse densities of 2500 pulses/cm² in 6061-T6 aluminum samples and 5000 pulses/cm² in 2024 aluminum samples are presented. High level of compressive residual stresses are produced −1600 MPa for 6061-T6 Al alloy, and −1400 MPa for 2024 Al alloy. It has been shown that surface residual stress level is higher than that achieved by conventional shot peening and with greater depths. This method can be applied to surface treatment of final metal products.