Studies on sintering of solid state synthesized Ba1−xKxBiO3−δ superconducting phase

Superconducting Ba_1−xK_xBiO_3−δ pellets were synthesized by solid state reaction followed by sintering. Thermo-gravimetric and differential thermo-gravimetric analysis (TG-DTA) of the mixture of nitrates was carried out to study the reactions during the phase formation. The effect of different sintering temperatures on the phase formation was studied. The X-ray diffraction data confirms the formation of superconducting Ba_0.6K_0.4BiO_2.23 phase at 700 °C. The surface morphological studies as a function of sintering temperature were studied by SEM. It is observed that the pellets prepared by solid state reaction followed its sintering at 700°C shows the superconducting transition at 26.8 K.     

Structural and superconductivity study on α-FeSex

We have successfully synthesized the α-FeSe_x binary tetragonal superconductors with nominal composition of FeSe_x (x=0.6-1.0) via conventional solid state reactions between Fe and Se sealed in quartz tubes. Fe and β-FeSe are the most commonly seen impurities in this binary system. A low-temperature annealing at 400 °C is found to be crucial to remove β-FeSe, which is the thermodynamic stable phase with hexagonal symmetry. For all the samples of FeSe_x, superconductivity is confirmed by magnetic measurements as well as resistivity measurements with their T_c at around 8 K. We noticed that their T_c does not vary with the different nominal Se amount. High-resolution synchrotron X-ray diffraction analysis revealed that the unit cell parameters of all these samples do not change within the error range, and their structure only tolerate the same very small amount of Se deficiency. Based on this study, we concluded that the α-FeSe_x superconductor only exist in a very narrow deficiency range.     

Mixed electrical conduction in Ce1−xCaxO2−x

The solid electrolyte Ce_1?xCa_xO_2-?x with the fluorite-type structure (Ca-doped CeO₂) is a mixed conductor. Conduction occurs predominantly by migration of O^2? ions via oxygen vacancies or by electrons, depending on the departure from stoichiometry. The ionic transference number σ_i/σ_i + σ_e was determined as a function of dopant concentration (0.07?x?0.15), temperature (400–800°C), and oxygen pressure by emf measurements with oxygen concentration cells. It is described by

The entropy term S¹(x) changes from 38.7k for x = 0.07 to 31.7k for x = 0.15; the enthalpy term, 5.42 eV, is independent of x and in excellent accord with semi-empirical calculations.     

Sustained high βN plasmas on EAST tokamak

Sustained high normalized beta (${\beta }_N～1.9$) plasmas with an ITER-like tungsten divertor have been achieved on EAST tokamak recently. The high power NBI heating system of 4.8 MW and the 4.6 GHz lower hybrid wave of 1 MW were developed and applied to produce edge and internal transport barriers in high ${\beta }_N$ discharges. The central flat q profile with $q(\rho )～1$ at $\rho <0.3$ region and edge safety factor $q_{95}=4.7$ is identified by the multi-channel far-infrared laser polarimeter and the EFIT code. The fraction of non-inductive current is about 40%. The relation between fishbone activity and ITB formation is observed and discussed.     

Magnetic susceptibility of liquid Na1−xSbxalloys

The magnetic susceptibility of liquid NaSb alloys was measured in a temperature range between 600°C and 1100°C. The NaSb system is supposed to exhibit, as does the CsSb system, a metal to semiconductor transition dependent upon composition. A relatively strong diamagnetic minimum of x = ?26 × 10^?6 cm³/mol was found near the composition of the stoichiometric formula Na₃Sb. This minimal susceptibility can be relatively well described with an ionic type binding model.     

Co-L3 X-ray absorption near-edge structure analysis of Pr1−xCaxCoO3−δ and Pr1−xSrxCoO3−δ

The valence state of Co ions in Pr_1−xCa_xCoO_3−δ and Pr_1−xSr_xCoO_3−δ has been investigated by an analysis of the Co-L₃ X-ray absorption near-edge structure (XANES) profile. The observed intensity distributions of Co-L₃ XANES change continuously with increasing concentration of alkaline-earth ions. To investigate the origin of this change in the XANES profile, charge transfer multiplet calculations were carried out, which could successfully explain the change in the spectral profile; they also suggest that the valence state of Co ions in Pr_1−xCa_xCoO_3−δ and Pr_1−xSr_xCoO_3−δ is between 3+ and 4+ and increases gradually with the concentration of alkaline-earth ions.     

Effects of hydrostatic pressure on the Coulomb-bound states in GaAs–Ga1−xAlxAs semiconductor superlattices

The effects of hydrostatic pressure on the Coulomb-bound states in GaAs–Ga_1−xAl_xAs and GaAs–AlAs semiconductor superlattices are theoretically studied. Calculations of the impurity binding energies for different configurations of the system and for various values of the hydrostatic pressure are performed in the framework of the parabolic-band and effective-mass schemes, and within the variational procedure. The hydrostatic-pressure dependence on the exciton energy is also obtained, and theoretical results are compared and found in good agreement with available experimental measurements.     

Structure and magnetism in Ho1−xSrxCoO3−δ

We have magnetically and structurally characterized the Ho_1−xSr_xCoO_3−δ family of materials where 0.67≤x≤0.95. The solid solution range and evolution of the structure as a function of x is established and correlated with the broad range of magnetic behavior observed. The structure is shown to be tetragonal I4/mmm although is possibly cubic when x=0.95. For 0.67≤x≤0.9 the material shows antiferromagnetic long range order and ferromagnetic clusters. At x=0.95 the magnetic transition is at 120 K and the imaginary susceptibility becomes non-zero and the temperature of the cusp in the ac susceptibility shows a frequency dependence indicative of glassiness.     

Structural and electronic properties of zinc blende BxAl1−xNyP1−y quaternary alloys via ?rst-principle calculations

The structural and electronic properties of cubic zinc blende BN, BP, AlN and AlP compounds and their B_xAl_1−xN_yP_1−y quaternary alloys, have been calculated using the non relativistic full-potential linearized-augmented plane wave FP-LAPW method. The exchange-correlation potential is treated with the local density approximation of Perdew and Wang (LDA-PW) as well as the generalized gradient approximation (GGA) of Perdew-Burke and Ernzerhof (GGA-PBE). The calculated structural properties of BN, BP, AlN and AlP compounds are in good agreement with the available experimental and theoretical data. A nonlinear variation of compositions x and y with the lattice constants, bulk modulus, direct and indirect band gaps is found. The calculated bowing of the fundamental band gaps is in good agreement with the available experimental and theoretical value. To our knowledge this is the first quantitative theoretical investigation on B_xAl_1−xN_yP_1−y quaternary alloy and still awaits experimental confirmations.     

Electrical conductivity and structural stability of SrCo1−xFexO3−δ

Perovskite compounds in the system of SrCo_1−xFe_xO_3−δ (x=0.2, 0.4 and 0.6) were synthesized by solid state reaction. SrCo_1−xFe_xO_3−δ shows the p-type small polaron conduction behavior. Electrical conductivity and oxygen vacancy content decrease with increase in Fe content. The incorporation of Fe increases the structural stability of SrCo_1−xFe_xO_3−δ at low temperatures, while decreasing the structural stability at high temperatures. Oxygen partial pressure has a strong influence on electrical conductivity. At low oxygen partial pressure, SrCo_0.8Fe_0.2O_3−δ will transform from cubic to orthorhombic structure. This structure can remain in 5%H₂/Ar only for a short time and then dissociates into Sr₃Fe₂O_6.64 and Co due to the reduction of B-site elements.     

The effect of La-substitution on magnetic properties of nanosized Sr1−xLaxTi0.05Zn0.2(Fe)11.75−δ(Fe)δO19 powders

A series of La-substituted M-type Sr hexaferrite powders Sr_1−xLa_xTi_0.05Zn_0.2Fe³⁺_11.75O₁₉, wherein x ranges from 0.1 to 0.5 with a step of 0.1, have been prepared by the conventional ceramic method and were then milled in a high energy mill to prepare nanosized powders. XRD investigation of the calcined and the milled powders shows that single phase hexaferrite structure has been formed after calcining and has not changed after milling. The lattice parameters and the mean crystallite sizes of the samples have been determined from the XRD data and Scherrer's formula. The results show that the lattice parameters (“а” and “c”) decrease with increase in La-substitution and the mean crystallite size of the milled powders is about 17 nm. Coercivities and magnetizations of the samples in a magnetic field of 16 kOe have been determined from the room temperature hysteresis loops. It was found that both parameters increase with La substitutions up to 0.3 and then decrease for higher substitutions. These variations were attributed to the enhancement of hyperfine field and spin-canting magnetic structure when La content increases. In addition, the magnetizations were smaller for the nanosized samples in comparison with those of bulk ones, which were discussed according to the core-shell model. Also the results show that annealing of the nanosized samples up to 500 °C can enhance coercivity and magnetization of the samples, which is discussed based on crystallite size growth.     

TE1n /TM1n激励圆锥喇叭辐射功率测量方法

研究了TE1n /TM1n模式激励的圆形口径喇叭天线的辐射场特征,导出了根据辐射场计算天线辐射总功率的方法:通过测定天线E面和H面的辐射场功率密度分布,分别进行球冠积分,其平均值即为天线的辐射总功率;并进行了数值仿真验证。分析了测量角度范围和测量点数目对测量功率的影响,提出了通过数据拟合来降低测量误差的一种方法;给出了测量角度范围和测量点数的选取原则,功率测量可在15 dB或18 dB波束宽度范围内进行,测量点数一般选15个左右。     

Exact PsTd invariant and PsTd symmetric breaking solutions,symmetry reductions and Bäcklund transformations for an AB–KdV system

In natural and social science, many events happened at different space–times may be closely correlated. Two events, A (Alice) and B (Bob) are defined as correlated if one event is determined by another, say, $B=\stackrel{?}{f}A$ for suitable $\stackrel{?}{f}$ operators. A nonlocal AB–KdV system with shifted-parity ($P_s$, parity with a shift), delayed time reversal ($T_d$, time reversal with a delay) symmetry where $B=\stackrel{?}{P_s}\stackrel{?}{T_d}A$ is constructed directly from the normal KdV equation to describe two-area physical event. The exact solutions of the AB–KdV system, including $P_s{T}_d$ invariant and $P_s{T}_d$ symmetric breaking solutions are shown by different methods. The $P_s{T}_d$ invariant solution show that the event happened at A will happen also at B. These solutions, such as single soliton solutions, infinitely many singular soliton solutions, soliton–cnoidal wave interaction solutions, and symmetry reduction solutions etc., show the AB–KdV system possesses rich structures. Also, a special Bäcklund transformation related to residual symmetry is presented via the localization of the residual symmetry to find interaction solutions between the solitons and other types of the AB–KdV system.     

Role of growth temperature and oxygen partial pressure on the structural and electrical properties of pulsed laser deposited La1−xSrxnO3−δ thin films

The paper presents the fabrication and characterization of La_0.65Sr_0.35MnO_3−δ (LSMO) polycrystalline thin films deposited directly on Si (1 0 0) substrates using pulsed laser deposition technique. Various deposition parameters like substrate temperature and oxygen partial pressure have been varied systematically to obtain stoichiometric, crack-free films with smooth surface morphology having nearly monodisperse grain size distribution. The substrate temperature variation from 600 to 800 °C had profound effects on the microstructure and topography of the deposited film, with optimum result being obtained at 700 °C. The variation of partial pressure of oxygen controls the deposition kinetics as well as the stoichiometry of the film in terms of oxygen vacancy, which influences the magnetic and electrical transport properties of the manganate films. The microstructure and crystallinity of the deposited films have been studied using X-ray diffraction, scanning electron microscopy and atomic force microscopy. A correlation between the oxygen stoichiometry and micro-structural and transport properties of the deposited films has been obtained.     

High temperature transport and thermoelectric properties of Ca3−xErxCo4O9+δ

Ca_3−xEr_xCo₄O_9+δ (x=0, 0.05, 0.15, 0.3 and 0.5) samples were prepared using a sol-gel method followed by hot-pressing sintering technique. Powder X-ray diffraction analysis showed the single-phases of Ca_3−xEr_xCo₄O_9+δ were obtained up to x=0.3 and the crystallinity of the samples decreased with increasing Er-doping amount. The high-temperature (323-1073 K) thermoelectric properties of the samples were investigated. The substitution of Er³⁺ for Ca²⁺ resulted in the decrease of electrical conductivity, thermal conductivity and the increase of Seebeck coefficient for all the samples except the x=0.05 one. The dimensionless figure of merit ZT reached 0.28 at 1073 K for Ca_2.7Er_0.3Co₄O_9+δ, indicating the thermoelectric properties of CaCo₄O_9+δ can be enhanced by doping Er in the system.     

Spectroscopic study on the interaction of Bacillus subtilis α-amylase with cetyltrimethylammonium bromide

The interaction between α‐amylase from Bacillus subtilis and cetyltrimethylammonium bromide (CTAB) has been investigated at various temperature conditions using fluorescence and circular dichroism (CD) spectroscopic methods. Fluorescence data revealed that the fluorescence quenching of α‐amylase by CTAB is the result of complex formation between CTAB and α‐amylase. The thermodynamic analysis on the binding interaction data shows that the interactions are strongly exothermic (ΔH°=−17.92 kJ mol⁻¹) accompanied with increase in entropy (ΔS° between 109 to 135 J mol⁻¹ K⁻¹). Thus the binding of CTAB to α-amylase is both enthalpic and entropic driven, which represent the predominate role of both electrostatic and hydrophobic interactions in complex formation process. The values of 2.17×10⁻³ M⁻¹ and 1.30 have been obtained from associative binding constant (K_a) and stoichiometry of binding number (n), from analysis of fluorescence data, respectively. Circular dichroism spectra showed the substantial conformational changes in secondary structure of α‐amylase due to binding of CTAB, which represents the complete destruction of both secondary and tertiary structure of α-amylase by CTAB.     

Investigation on cation distribution and magnetic properties in self-doped manganites La0.6−xSr0.4MnO3−δ

Self-doped manganites with nominal composition La_0.6−xSr_0.4MnO_3−δ (0≤x≤0.175) have been prepared by the sol–gel method. The X-ray diffraction (XRD) patterns and magnetic measurements indicate that the samples have two phases with the ABO₃ perovskite structure being the dominant phase and Mn₃O₄ being the minor phase when the doping level x≥0.05. On the basis of the thermal equilibrium theory of crystal defects, the contents of various ions in the perovskite phases were estimated, in which there are Mn²⁺ ions and no vacancies at A sites. The ion contents have been corrected by Rietveld fitting of the powder samples' X-ray diffraction data. The change tendency of the Curie temperature T_C vs. the Mn⁴⁺ ion content ratio at the B sites of ABO₃ perovskite phase is in accord with the experimental result of the samples La_1−xSr_xMnO₃.     

Effect of p-μc-Si1−xOx:H layer on performance of hetero-junction microcrystalline silicon solar cells under light concentration

Preparation of p-type hydrogenated microcrystalline silicon oxide thin films (p-μc-Si_1−xO_x:H) by 13.56 MHz RF-PECVD method for use as a p-layer of hetero-junction μc-Si:H solar cells is presented. We investigated effects of wide-gap p-μc-Si_1−xO_x:H layer on the performance of hetero-junction μc-Si:H solar cells under various light intensity. We observed that a wide-gap p-μc-Si_1−xO_x:H was effective in improving the open-circuit voltage (V_oc) of the solar cells. We also confirmed that the V_oc logarithmically increased with increasing light intensity, and the enhancement of V_oc became larger with increasing band gap of p-layer. These results indicate that wide-gap p-μc-Si_1−xO_x:H is a promising material for use as window layer in hetero-junction μc-Si:H solar cells.     

MCsn cluster formation on organic surfaces: A novel way to depth-profile organics?

In this work, we investigated the bombardment of polymer surfaces (PC, PMMA) with very low energy (250 eV) Cs⁺ ions.In the positive mode, we observed many cations combining a molecular fragment of the polymer (M) with two Cs atoms, similar to the well-known MCs₂⁺ clusters commonly observed in inorganic depth profiling with Cs. For example, Cs₂COOH⁺ or Cs₂C₆H₅O⁺ were measured on PC and Cs₂CH₃O⁺ or Cs₂C₄H₅O₂⁺ were measured on PMMA. In fact, most of the polymer characteristic fragments measured in negative spectra also appear in the positive spectra, combined with two Cs atoms. It is remarkable that stable negative ions tend to combine not with one Cs, but with two Cs atoms to create the MCs₂⁺ cluster.This effect is, to some extent, similar to the well-known cationisation of polymers (with Ag or Au) although here few clusters with only one Cs atom are detected (MCs⁺ clusters), like in classical cationisation. The most abundant clusters are the MCs₂⁺ clusters, but heavier clusters (MCs₃⁺, MCs₄⁺ and above) are also measured with high yields in the spectrum.Surprisingly, some of those MCs₂⁺ clusters were still detected even after a very long sputtering fluence (above 10¹⁷ ions/cm²), proving that some molecular depth profiling is also possible in this “Cs₂-cationisation” mode. In other words, this work could open the way to an extension of the MCs_n⁺ cluster analysis, commonly used in inorganic depth profiling, to the in-depth molecular analysis of organic layers.     

Luminescence studies of a combustion-synthesized blue–green BaAlxOy:Eu,Dy nanoparticles

Blue–green emitting BaAl_xO_y:Eu²⁺,Dy³⁺ phosphor was synthesized by the combustion method. The influence of various parameters on the structural, photoluminescence (PL) and thermoluminescence (TL) properties of the phosphor were investigated by various techniques. Phosphor nanocrystallites with high brightness were obtained without significantly changing the crystalline structure of the host. In the PL studies, broad-band excitation and emission spectra were observed with major peaks at 340 and 505 nm, respectively. The observed afterglow is ascribed to the generation of suitable traps due to the presence of the co-doped Dy³⁺ ions. Though generally broad, the peak structure of the TL glow curves obtained after irradiation with UV light was non-uniform with suggesting the contribution to afterglow from multiple events at the luminescent centers. Further insight on the afterglow behavior of the phosphor was deduced from TL decay results.