Séparation de traces métalliques sur goutte de mercure; application à la préconcentration de Cu(II) et Cu(I)

A method for the rapid separation of copper(II) traces on metallic mercury is proposed. The separation is rendered possible by the reduction of Cu(II) to Cu(I) on mercury in the presence of iodide ions followed by the adsorption of the uncharged complex, Cu(I), on Hg⁰. After a minute of agitation, this adsorption is quantitative (90–100%) for initial concentrations of Cu(II) between 10^?4 to 10^?6 M and iodide cone, of 10^?2 to 10^?3 M at pH 3. The volumes of the aqueous solutions are of the order of 3–10 ml and those of the drops of mercury between 0.5–1 ml. The tests were made using the isotope ⁶⁴Cu (T _1/2 = 12.8 h).     

Determination of Hg(II) ions in water samples by a novel Hg(II) sensor,based on calix[4]arene derivative

A PVC membrane electrode for Hg(II) ions, based on a new cone shaped calix[4]arene (L) as a suitable ionophore was constructed. The sensor exhibits a linear dynamic in the range of 1.0 × 10^?6–1.0 × 10^?1 M, with a Nernstian slope of 29.4 ± 0.4 mV decade^?1, and a detection limit of 4.0 × 10^?7 M. The response time is quick (less than 10 s), it can be used in the pH range of 1.5–4, and the electrode response and selectivity remained almost unchanged for about 2 months. The sensor revealed comparatively good selectivity with respect to most alkali, alkaline earth, and some transition and heavy metal ions. It was successfully employed as an indicator electrode in the potentiometric titration of Hg²⁺ ions with potassium iodide, and the direct determination of mercury content of amalgam alloy and water samples.     

Lead-selective electrodes based on lead(IV) oxide

Lead(IV) oxide electrodes are shown to give near-theoretical calibration slopes for lead(II) ions over the range 10^?3–10^?5 mol l^?1, and to have near-theoretical standard potentials in different acidic media. They are compared with lead sulphide-silver sulphide membrane electrodes and shown to be more tolerant of acidity and copper(II), mercury(II) and iron(III) ions. Iron(II) and manganese(II), however, interfere significantly. Some of the advantages of the lead(IV) oxide electrode are brought out in the determination of the solubility product of lead sulphate; implications for constructing phosphate- and sulphate-sensitive electrodes are mentioned.     

1‐Pyrrolidine Dicarbodithioate Based Electrodes for Determination of Iron(III) in Lubrication Oil

The lipophillic ammonium salt of 1‐pyrrolidine dicarbodithioic acid (PCDT) (I) was introduced as a new selective ionophore for an iron selective electrode. In addition, the effect of immobilization of 18‐crown‐6 (18CE6) (membrane type‐II), on the electrode performance was discussed. The slope of the PCDT‐based (I) electrode was (20 mV/decade). The linear concentration range was (10^?5–10^?1 M) after one day doping. The detection limit for electrode type‐(II) was (1.3×10^?6 M). For membrane with only 18CE6 (type‐III) the linear range and the detection limit were improved (10^?5–10^?1 M and 3.2×10^?6 M, respectively). The pH‐range was between 5–11 for type‐II, and III electrodes, while it was 7–11 for type‐I electrode. Most of the common cations were tested for the evaluation of the electrode selectivity with correlation to the ionic radii of the tested cations. Among them only Ag⁺ and Pb²⁺ were the real interference for type‐III electrode. Application of using the electrode for the determination of iron in lubrication oil samples was performed with RSD (1.77–2.7%) and (1.01–2.3%) for type‐II and III electrodes, respectively. The corresponding recovery ranges were (93.0–99.9%) and (96.3–100%). The obtained results were compared to those of an atomic absorption spectrophotometric method.     

Mercury ion selective poly(aniline) solid contact electrode based on 2-mercaptobenzimidazol ionophore

A mercury(II) ion selective poly(aniline) solid contact electrode based on 2-mercaptobenzimidazol (2MBI) ionophore as a sulfur containing sensing material was successfully developed. The electrode exhibits a good linear response of 29.1 mV/decade (at 20 ± 0.2°C, r ² = 0.997) within the concentration range of 1 × 10^?2?1 × 10^?7 M Hg(II). The composition of this electrode was: ionophore 0.100, polyvinylchloride (PVC) 0.330, dibutylphthalate (DBP) 0.470, potassiumtetrakis(4-chlorophenyl)borate (KTpCIPB) 0.090, and oleic acid (OA) 0.010. A poly(aniline) solid contact electrode based on 2MBI with DBP and OA plasticizers exhibited the best response characteristics of the results obtained for similarly coated wire type electrodes and solid contact electrodes based on only one DBP plasticizer. The electrode shows good selectivity for mercury(II) ions in comparison with alkali, alkaline earth, transition and heavy metal ions. This electrode is suitable for use with aqueous solutions of pH 3.3?C8.0 and the standard deviation in the measured EMF difference was ±0.5 mV in a mercury nitrate sample solution of 1.0 × 10^?2 M and ±1.1 mV in a mercury nitrate sample solution of 1.0 × 10^?3 M. The stabilization time was less than 15 min and the response time was less than 33 s. The electrode was applied as a sensor for the determination of Hg(II) content in a sea water sample and some amalgam alloys. The results show good correlation with data obtained by atomic absorption spectrometry.     

Cobalt(II)-selective membrane electrode based on N,N′-di(thiazol-2-yl)formimidamide

A new PVC-membrane electrode for Co²⁺ ions based on N,N′-di(thiazol-2-yl)formimidamide (TF) as membrane carrier has been developed. The electrode resulted in Nernstian response (29.5?±?0.4?mV decade^?1) for Co²⁺ ion over a wide concentration range (2.5?×?10^?7 ?1.0?×?10^?1?M) with a detection limit of 6.1?×?10^?8?M. The sensor has a response time of about 10?s, and can be used for at least 2 months without observing any deviation from the Nernstain response. The electrode revealed good selectivity towards cobalt(II) ion over a wide variety of alkali, alkaline earth, transition, and heavy metal ions and could be used in the pH range 2.0–7.0. The electrode was used for determination of Co²⁺ in real samples.     

Novel Potentiometric PVC‐Membrane and Coated Graphite Sensors for Lanthanum(III)

Preliminary theoretical studies revealed the selective complexation of bis (2‐mercaptoanil) diacetyl (BMDA) with La³⁺ over several alkali, alkaline earth and heavy metal ions. Thus, novel PVC‐based membrane (PBM) and coated graphite membrane (CGM) sensors for La(III) based on BMDA were prepared. The electrodes display Nernstian behavior over wide concentration ranges (i.e., 1.0×10^?5–1.0×10^?1 M for PBM and 1.0×10^?6–1.0×10^?1 M for CGM). The potential response of sensors was pH independent in the range of 4.0–8.0. The sensors possess satisfactory reproducibility, fast response time (<15 s), and specially excellent discriminating ability for La³⁺ ions with respect to most of the cations. The membrane sensor was used as an indicator electrode in potentiometric titration of lanthanum ions with EDTA. The coated graphite membrane electrode was applied in determination of fluoride ions in mouth wash preparations.     

Trace Analysis of Al (III) Ions Based on the Redox Current of a Conducting Polymer

A conducting polymer was electrochemically prepared on a Pt electrode with newly synthesized 3′‐(4‐formyl‐3‐hydroxy‐1‐phenyl)‐5,2′ : 5′,2″‐terthiophene (FHPT) in a 0.1 M TBAP/CH₂Cl₂ solution. The polymer‐modified electrode exhibited a response to proton and metal ions, especially Al(III) ions. The poly[FHPT] was characterized with cyclic voltammetry, EQCM, and applied to the analysis of trace levels of Al(III) ions. Experimental parameters affecting the response of the poly[FHPT] were investigated and optimized. Other metal ions in low concentration did not interfere with the analysis of Al(III) ions in a buffer solution at pH 7.4. The response was linear over the concentration range of 5.0×10^?8–7.0×10^?10 M, and the detection limit was 5.0×10^?10 M using the linear sweep voltammetry (LSV). Employing the differential pulse voltammetry (DPV), the response was linear over the 1.0×10^?9–5.0×10^?11 M range and the detection limit was 3.0×10^?11 M. The relative standard deviation at 5.0×10^?11 M was 7.2% (n=5) in DPV. This analytical method was successfully verified for the analysis of trace amounts of Al(III) ions in a human urine sample.     

Construction and characterization of nano iron complex ionophore for electrochemical determination of Fe(III) in pure and various real water samples

Electrochemical methods represent an important class of widely used techniques for the detection of metal ions. The unique chemical and physical properties of nanoparticles make them extremely suitable for designing new and improved sensing devices, especially electrochemical sensors and biosensors. This study focused on the synthesis of a nano‐Fe(III)–Sud complex and its characterization using various spectroscopic and analytical tools, optimized using the density functional theory method, screened for antibacterial activity and evaluated for possible binding to DNA using molecular docking study. Proceeding from the collected information, nano‐Fe(III)–Sud was used further for constructing carbon paste and screen‐printed ion‐selective electrodes. The proposed sensors were successfully applied for the determination of Fe(III) ions in various real and environmental water samples. Some texture analyses of the electrode surface were conducted using atomic force microscopy. At optimum values of various conditions, the proposed electrodes responded towards Fe(III) ions linearly in the range 2.5 × 10^?9–1 × 10^?2 and 1.0 × 10^?8–1 × 10^?2 M with slope of 19.73 ± 0.82 and 18.57 ± 0.32 mV decade^?1 of Fe(III) ion concentration and detection limit of 2.5 × 10^?9 and 1.0 × 10^?8 M for Fe(III)–Sud‐SPE (electrode I) and Fe(III)–Sud‐CPE (electrode II), respectively. The electrode response is independent of pH in the range 2.0–7.0 and 2.5–7.0, with a fast response time (4 and 7 s) at 25°C for electrode I and electrode II, respectively. Moreover, the electrodes also showed high selectivity and long lifetime (more than 6 and 3 months for electrode I and electrode II, respectively). The electrodes showed good selectivity for Fe(III) ions among a wide variety of metal ions. The results obtained compared well with those obtained using atomic absorption spectrometry.     

Voltammetric determination of mercury(II) using a modified pencil graphite electrode with 4-(4-methylphenyl aminoisonitrosoacetyl)biphenyl

A sensitive and selective method for determination of mercury(II) with “4-(4-methylphenyl aminoisonitrosoacetyl)biphenyl (TKO)-modified pencil graphite electrode” was developed. All factors affecting determination process were optimized. Differential pulse voltammetry with 4-(4-methylphenyl aminoisonitrosoacetyl)biphenyl-modified electrode showed a linear response between 1.0 × 10^?5 and 1.0 × 10^?3 M (R ² = 0.9994). The detection limit of this electrode was found as 5.85 × 10^?7 M (S/N = 3). The effects of different cations on the determination of mercury(II) were investigated and found that modified electrode is highly selective. The developed method was applied for mercury determination in different water samples.     

Iron (III) Ion Selective Electrode Based on Dithia 12-Crown-4

An iron (III) ion selective PVC membrane electrode based on 1,7-dithia 12-crown-4 as a neutral carrier was prepared. Monovalent responses with a Nerstian slope of 56+1 mV/decade was observed for the Fe (III) ion-selective electrode within the concentration range 10^?3–10^?5 M Fe (NO₃)₃. The monovalent responses may be attributed to the formation of Fe (OH)₂⁺ or Fe (OH)₂(H₂O)⁺₄ species in aqueous solutions and the absorption of these ions into the PVC electrode membrane. The electrode exhibited good selectivity for Fe (III) in comparison with various alkali, alkali-earth and some heavy metal ions. The effects of the composition of the membrame, addition of STPB (sodium tetraphenyl borate), the concentration of internal solution of the electrode and anions in the test solutions were discussed.     

Electrode Modified with Langmuir–Blodgett (LB) Film of Calixarenes for Preconcentration and Stripping Analysis of Hg(II)

A new type of current sensor, Langmuir–Blodgett (LB) film of calixarene on the surface of glassy carbon electrode (GCE) was prepared for determination of mercury by anodic stripping voltammetry (ASV). An anodic stripping peak was obtained at 0.15 V (vs. SCE) by scanning the potential from ?0.6 to +0.6 V. Compared with a bare GCE, the LB film coated electrode greatly improves the sensitivity of measuring mercury ion. The fabricated electrode in a 0.1 M H₂SO₄+0.01 M HCl solution shows a linear voltammetric response in the range of 0.07–40 μg L^?1 and detection limit of 0.04 μg L^?1 (ca. 2×10^?10 M). The high sensitivity, selectivity, and stability of this LB film modified electrode demonstrates its practical application for a simple, rapid and economical determination of Hg²⁺ in a water sample.     

Potassium ion-selective electrode based on a cobalt(II)-hexacyanoferrate film-modified electrode

A potassium ion-selective electrode based on a cobalt(II)-hexacyanoferrate(III) (CHCF) film-modified glassy carbon electrode is proposed. The electroactive film is introduced onto the glassy carbon electrode surface by electrodeposition of cobalt, which forms a thin CHCF film on subsequent anodic scanning in KClHCl solution (pH 5.0–5.5) containing K₃Fe(CN)₆. The thickness of the film on the electrode surface can be controlled by changing the electrodeposition time and the concentrations of cobalt(II) and Fe(CN)^3?₆ ions. The modified electrode exhibits a linear response in the concentration range 1 × 10^?1 ?3 × 10^?5 M potassium ion activity, with a near-Nernstian slope (48–54 mV per decade) at 25 ± 1°C. The detection limit is 1 × 10^?5 M. The stability, response time and selectivity were investigated. The electrode exhibits good selectivity for potassium ion with the twelve cations investigated. The relative standard deviation is 1.5% (n=10). The effects of the thickness of the electroactive film and the pH of the solution on the electrode response were also investigated.     

Determination of uranium(VI) in sea water by cathodic stripping voltammetry of complexes with catechol

Polarographic (d.c.) measurements showed that complex ions of uranium(VI) with catechol adsorb on the dropping mercury electrode. This effect is used to determine uranium(VI) directly in sea water. Optimal conditions include pH 6.8, 2 × 10^?3 M catechol, and a collection potential between ?0.1 and ?0.4 V (vs. Ag/AgCl) at a hanging mercury drop electrode. The cathodic scan is made with the linear-scan or differential-pulse mode (d.p.c.s.v.). The detection limit with the d.p.c.s.v, mode is 3 × 10^?10 M after a collection period of 2.5 min. Between pH 6 and 8, the peak height increases with pH and with catechol concentration up to 5 × 10^?3 M. There is linear relationship between the collection time and the measured peak height until the drop surface becomes saturated. With a collection period of 3 min, the reduction current increases linearly with the metal concentration up to about 5 × 10^?3 M U(VI). The maximum adsorption capacity of the mercury drop is 4.4 × 10^?10 mol cm²; each complex ion then occupies 0.38 nm², equivalent to the size of about one catechol molecule. Interference by high concentrations of Fe(III) is overcome by selectively adsorbing U(VI) at a collection potential near the reduction potential of Fe(III). Organic surfactants reduce the peak height for uranium by up to 75% at unnaturally high concentrations only (4 mg l^?1 Triton X-100). Competition by high concentrations of Cu(II) for space on the surface of the drop is eliminated by addition of EDTA.     

Nickel(II) Ion-Selective Electrode Based on 2,5-Thiophenyl bis(5-tert-Butyl-1,3-Benzoxazole

ABSTRACT

A PVC membrane sensor for Nickel (II) ions based on 2,5-thiophenyl bis(5-tert-butyl-1,3-benzoxazole) as membrane carrier was prepared. The sensor exhibits a Nernstian response for Ni²⁺ ions over a wide concentration range (10^?2–10^?5M). It has a relatively fast response time and can be used for at least 2 months without any considerable divergence in potentials. The nature of the plasticizer, the additive, the concentration of internal solutions in the electrodes and the composition of the membrane were investigated. The proposed membrane electrode revealed very good selectivities for Ni²⁺ over a wide variety of other metal cations and could be used in pH range of 4.0–8.0. It was successfully applied for the direct determination of Ni²⁺ in solution and as an indicator electrode in potentiometric titration of nickel ion in both water and 85% acetonitrile solutions.     

Voltammetric Determination of Mercury(II) at Poly(3‐hexylthiophene) Film Electrode. Effect of Halide Ions

The well‐known method for the determination of mercury(II), which is based on the anodic stripping voltammetry of mercury(II), has been adapted for applications at the thin film poly(3‐hexylthiophene) polymer electrode. Halide ions have been found to increase the sensitivity of the mercury response and shift it more positive potentials. This behavior is explained by formation of mercuric halide which can be easily deposited and stripped from the polymer electrode surface. The procedure was optimized for mercury determination. For 120 s accumulation time, detection limit of 5 ng mL^?1 mercury(II) has been observed. The relative standard deviation is 1.3% at 40 ng mL^?1 mercury(II). The performance of the polymer film studied in this work was evaluated in the presence of surfactants and some potential interfering metal ions such as cadmium, lead, copper and nickel.     

A highly selective colorimetric sensor for Hg2+ based on a copper (II) complex of thiosemicarbazone in aqueous solutions

By applying an indirect strategy, a new copper (Ⅱ) complex of a thiosemicarbazone L has been successfully developed as a colorimetric chemosensor for the sensitive detection of mercury (Ⅱ) ions. In the presence of copper (Ⅱ) ions, the colorless solution of L became yellow; however, upon the addition of traces of mercury (Ⅱ) ions, the yellow color faded to colorless immediately. Other ions, including Fe3+ , Ag+ , Ca2+ , Zn2+ , Pb2+ , Cd2+ , Ni2+ , Co2+ , Cr3+ and Mg2+ had a negligible influence on the probe behavior. The detection limits were 5.0×10 -6 M and 3.0×10 -7 M of Hg2+ using the visual color changes and UV-vis changes respectively. Test strips based on Cu-L were fabricated, which could act as a convenient and efficient Hg2+ test kits.     

Preparation of Cu (II) imprinted polymer electrode and its application for potentiometric and voltammetric determination of Cu (II)

The Cu (II) imprinted polymer glassy carbon electrode (GCE/Cu-IP) was prepared by electropolymerization of pyrrole at GCE in the presence of methyl red as a dopant and then imprinting by Cu²⁺ ions. This electrode was applied for potentiometric and voltammetric detection of Cu²⁺ ion. The potentiometric response of the electrode was linear within the Cu²⁺ concentration range of 3.9 × 10^?6 to 5.0 × 10^?2 M with a near-Nernstian slope of 29.0 mV decade^?1 and a detection limit of 5.0 × 10^?7 M. The electrode was also used for preconcentration anodic stripping voltammetry and results exhibited that peak currents for the incorporated copper species were dependent on the metal ion concentration in the range of 1.0 × 10^?8 to 1.0 × 10^?3 M and detection limit was 6.5 × 10^?9 M. Also the selectivity of the prepared electrode was investigated. The imprinted polymer electrode was used for the successful assay of copper in two standard reference material samples.     

Original Potentiometric Ytterbium(III) PVC-Membrane Sensor Based on N1,N2-Bis-[1-(2-hydroxy-1,2-diphenyl)ethylidene]ethanedihydrazide

Abstract

In this work, we describe the construction, performance, and applications of an original ytterbium(III) sensor based on N¹,N²-bis-[1-(2-hydroxy-1,2-diphenyl)ethylidene]ethanedihydrazide (BHDEH), which acts as a suitable carrier. Because it has a low detection limit of 4.2 × 10^?7 M, the sensor response for the Yb(III) ion is Nernstian over a wide concentration range: four decades of concentration (1.0 × 10^?6 to 1.0 × 10^?2 M). The response time of the electrode is less than 10 s, it can be used in the pH range of 3.2–8.3, and its duration is at least 2 months without any considerable potential divergence. The sensor revealed very good selectivity for Yb(III) in the presence of several metal ions. To investigate the sensor analytical applicability, it was tested as an indicator electrode in the potentiometric titration of Yb(III) solution with standard EDTA solution. The proposed electrode was also used to determine fluoride ions in mouthwash.     

A Novel Al(III)‐Selective Electrochemical Sensor Based on N,N′‐Bis(salicylidene)‐1,2‐phenylenediamine Complexes

A polyvinylchloride membrane sensor based on N,N′‐bis(salecylidene)‐1,2‐phenylenediamine (salophen) as membrane carrier was prepared and investigated as a Al³⁺‐selective electrode. The sensor exhibits a Nernstian response toward Al(III) over a wide concentration range (8.0×10^?7–3.0×10^?2 M), with a detection limit of 6.0×10^?7 M. The potentiometric response of the sensor is independent of the pH of the test solution in the pH range 3.2–4.5. The electrode possesses advantages of very fast response and high selectivity for Al³⁺ in comparison with alkali, alkaline earth and some heavy metal ions. The sensor was used as an indicator electrode, in the potentiometric titration of aluminum ion and in determination of Al³⁺ contents in drug, water and waste water samples.