Use of Derivative Spectrophotometry for the In Vitro Determination of Allopurinol and Uric Acid Mixtures

Abstract

Allopurinol and uric acid are successfully assayed either in laboratory made mixtures or in urine using derivative spectrophotometry. The former is determined through first - derivative signal (¹ D) measurement at 284 nm, and the latter through second - derivative signal (²D) measurement at 293 nm. The colinearity of these values versus concentration of both compounds in the range 0.2–1.2 mg% permits their determination with high accuracy and good reproducibility. The method is recommended to monitor the allopurinol therapy in treatment of chronic gouty patients.     

Spectrophotometric and First Derivative Spectrophotometric Determination of Magnesium with 1-Hydroxy-2-Carboxyanthraquinone

Abstract

1-Hydroxy-2-carboxyanthraquinone reacts with magnesium in ethanol-water mixtures to form a red complex having an absorption maximum at 490 nm in alkaline medium. A detailed study of the characteristics of this complex has been carried out and a spectrophotometric method for the determination of magnesium at the 0.4–4.0 μg ml^?1 level is proposed. The method has been sensitized by employing first derivative spectrophotometry. By the use of the derivative approach magnesium can be determined between 0.08–0.40 μg ml^?1. Statistical analysis of the results is also described.     

Simultaneous Determination of Platinum and Palladium by Second Derivative Spectrophotometry Using 3-(2'-Thiazolylazo)-2, 6-Diaminopyridine as Chromophore Ligand

ABSTRACT

A second derivative spectrophotometric method has been developed for the determination of palladium and platinum in mixtures. The method is based on the formation of the platinum and palladium complexes with 3-(2-thiazolylazo)-2, 6-diaminopyridine, (2, 6-TADAP), in the presence of 1.7 M perchloric acid solution, upon heating at 90° C for 30 min and on the subsequent direct derivative spectrophotometric measurement. The zero-crossing approach and the graphic method were used for determination of platinum and palladium, respectively. Each analyte was determinated in the presence of one another in the ranges 8.9×10^-7 -3.1×10^-5 M for platinum and 4.6×10^-7 - 6.8×10^-5 M, for palladium. The detection limits achieved (3a) were found to be 2.7×10^-7 M of platinum and 1.4×10^-7 M of palladium. The relative standard deviations were in all instances less than 1.0%. In this work is included a study of effect of interferents and the application of the proposed method in synthetic mixtures.     

Speciation Analysis of Osmium(VIII) and Osmium(IV) by UV‐VIS Spectrophotometry Using Quercetin as the Reagent

Abstract

The UV‐VIS spectrophotometric methods for the determination of Os(VIII) (as OsO₄) and Os(IV) (as OsCl₆ ^2? complex) in their mixtures were developed. Quercetin (Q), a flavonoid compound, was used as a chromogenic reagent. Both direct and derivative spectrophotometry can be employed for the determination of Os(VIII). The calculation of the first‐derivative spectrum of the examined mixture and the use of the signal at 285.1 nm allows reaching a better detection limit (0.01 µg mL^?1 Os) as compared with direct spectrophotometry (0.1 µg mL^?1 Os). Relative standard deviations of the results are in the range of 0.87%–4.65% and 0.45%–1.15% for direct and derivative mode, respectively. Selective redox reaction of OsO₄ with Q under the conditions used (0.05 M HCl, 1×10^?4 M Q, 15 min heating at 70°C) makes the basis of its determination in mixtures with the OsCl₆ ^2? complex. Quercetin does not react with the OsCl₆ ^2? complex. The signals of the OsCl₆ ^2? complex can be isolated from the examined mixtures by the calculation of the third‐order derivative spectra and the use of the values at 340.0 nm. The effectiveness of the reduction of OsO₄ in chloride solutions has been studied by the developed method.     

Simultaneous Determination of Procaine Penicillin G and Benzathine Penicillin G by Second Derivative Spectrophotometry

Abstract

A new method for determining the binary mixtures of procaine penicillin G and benzathine penicillin G using “zero-crossing” second derivative spectrophotometry is described. Calibration graphs were linear up to 8.80 10^?5 M for procaine penicillin G and 4.40 10^?5 M for benzathine penicillin G. The method was realized in ethanol/water medium (30 % v/v). A complete and exhaustive statistical analysis of the experimental data was realized to demonstrate the validity of method. The method was applied for determining procaine penicillin G and benzathine penicillin G synthetic mixtures with good results. The procedure does not require any separation step.     

A new method of Fourier-transform smoothing with ratio spectra derivative spectrophotometry

A new method which combines Fourier-transform smoothing with ratio spectra derivative spectrophotometry has been developed for analysis of binary and ternary mixtures. The method proposed has been applied to the simultaneous determination of a binary mixture of 0.974–2.026 × 10^–2?g?L^–1 nitrate and nitrite and to a ternary mixture of 1.840–3.888 × 10^–3 g L^–1 histidine, phenylalanine, and tryptophan. The relative standard derivations are between 0.07 and 5.3% for the former system, and between 0.5 and 7.3% for the latter. The results show that the method proposed is more accurate than multiple linear regression.     

First Order Derivative Spectrophotometric Determination of Vanadium(V) and Iron(III) Individually and Simultaneously

A novel, sensitive and highly selective first derivative spectrophotometric method is proposed for the determination of vanadium(V) and iron(III) metal ions separately and simultaneously in a mixture. 2-Hydroxy-1-naphthaldehyde benzoylhydrazone (OHNABH) reacts with vanadium(V) and iron(III) in sodium acetate–acetic acid buffer medium (pH 5.0) forming yellow and yellowish brown colored soluble complexes, respectively. The first derivative curves of these colored solutions show maximum derivative amplitudes at 465 nm (V(V)) and 540 nm (Fe(III)) obeying Beer's law in the range 0.12–2.50 g ml^–1 and 0.14–4.20 g ml^–1, respectively. Large number of foreign ions do not interfere in the present method. A very simple and accurate simultaneous first derivative method is also reported for the determination of V(V) and Fe(III) in mixtures without solving simultaneous equations. The method is applied for the analysis of various natural samples, food and biological materials.     

Multivariate analysis of chlorophenols by diode array spectrophotometry

A multivariate-multicomponent analysis method for the determination of chlorophenols by diode array derivative spectrophotometry is proposed. The method is based on extraction of chlorophenols directly or as ion pairs with tetrabutylammonium as the counterion in chloroform at pH 9.1. Prediction and quantitative determinations (within the concentration range 3.0–15.0 mg liter⁻¹) of two-, three-, and four component mixtures were possible using multivariate calibration of first-derivative spectra and a multicomponent analysis computer program based on least-squares regression.     

Simultaneous determination of ibuprofen and paracetamol using derivatives of the ratio spectra method

Simple, rapid and accurate new method is described for the simultaneous determination of ibuprofen (IB) and paracetamol (PA) in two components mixture and Cetofen tablets. The method depends on the derivative of the ratio spectra DD by measurement of the amplitude of ¹DD at 225.6 nm and the amplitude of ²DD at 238.9 nm for IB and PA. Calibration graphs are linear in the range 2–32 (LOD 0.53) and 2–24 (LOD 0.57) μg/ml IB and PA, respectively. The proposed method is successfully applied for simultaneous determining IB and PA in authentic mixtures and Cetofen tablets.     

Derivative Spectrophotometric Determination of Copper and Palladium Simultaneously by Using MDTC as a Reagent

Abstract

A selective, sensitive, and economical derivative spectrophotometric method has been developed for the determination of trace amount of Cu(II) and Pd(II) with MDTC as a reagent in the presence of CTAB, a solubilizing agent. The molar absorption coefficient and analytical sensitivities of the 1:2 Cu(MDTC)₂ and Pd(MDTC)₂ complexes are 2.467×10⁴ and 2.989×10⁴ l mol^?1, respectively. The developed derivative procedure, is applied for the rapid and selective simultaneous determination of Cu(II) and Pd(II) in the range of 0.2–15 and 0.1–10 µg/ml, respectively. Complex matrices, including alloys, biological samples, pharmaceutical samples and synthetic mixtures have been successfully analyzed for trace amounts of two metal ions.     

Simultaneous Determination of Nickel(II) and Copper(II) by Second‐Derivative Spectrophotometric Method in Micellar Media

A second‐derivative spectrophotometric method based on zero‐crossing over technique is developed in simultaneous determination of copper(II) and nickel(II) ions. Methylthymol blue (MTB) as a chromogenic reagent and cetyltrimethylammonium bromide as a surfactant were used, and measurements were carried out in buffered solution at pH 6 and at a temperature of 25 °C. The amplitude of derivative spectra was measured at wavelengths of 631.9 and 587.7 nm for the simultaneous determination of Ni²⁺ and Cu²⁺, respectively. Linearity was obtained in the range of 0.5–5.0 μg mL^?1 for both ions in the presence of 0.0–5.0 μg mL^?1 of the other ion as an interfering ion. IUPAC detection limits for Cu²⁺ and Ni²⁺ ions were obtained at 0.48 and 0.43 μg mL^?1, respectively. The proposed procedure has been applied successfully for the simultaneous determination of copper and nickel in synthetic binary mixtures and real samples.     

Application of derivative UV spectrophotometry to the simultaneous determination of nitrate and nitrite ions in bath solutions for alkaline black-oxidation of steel

Second order derivative spectrophotometry was applied to the determination of nitrite and nitrate ions in bath solutions for alkaline black-oxidation of steel. The measurements were directly taken after dilution of the samples at λ = 336.4 nm for NO₃ ^– and λ = 390 nm for NO₂ ^–. The method was checked on artificial mixtures and applied to real samples containing approximately 5.5% NaNO₂ and 6% NaNO₃. The results agree well with those obtained by the standard manganometric method. Received: 8 July 1996 / Revised: 24 September 1996 / Accepted: 28 September 1996     

Simultaneous Determination of Lonidamine, 1-(2,4-Dichlorobenzyl)-1h-indazole-3-carboxylic Acid,a New Antitumoral,and Its Impurity,N2 Substituted Isomer,by UV Derivative Spectrophotometry

Abstract

A direct and fast analytical method for the determination of Lonidamine and its impurity of synthesis, the N₂ alkylated isomer, by UV derivative spectrophotometry, is described.

The procedure was defined by regression analysis for a high number of standard solutions.

Linear relationships were obtained between mixture composition and maximum amplitude in <²D at 316 nm for Lonidamine quantitation, and peak trough ⁴D 226,234 and ⁴D 323,316 amplitudes by utilising polynomial equation for N₂ isomer quantitation.

The method, yielding accurate and precise results, was satisfactorily applied to laboratory mixtures and to a commercial formulation.     

Quantitative thermogravimetric analysis of binary mixtures

Thermogravimetric analysis is used to determine the amounts of Mg(OH)₂ and Mg(CH₃COO)₂in a mixture thereof. The application and suitability of different analysis methods are discussed. In the first method the mass losses in the temperature ranges as indicated by the decomposition of the pure compounds were used. Results obtained using these temperature ranges were unusable. The percentage mass losses due to the decomposition of Mg(OH)₂ and Mg(CH₃COO)₂ were then determined in a second method using the minimum in the derivative mass vs. temperature curves. The results obtained by this method compared well with the actual values for mixtures containing more than 15% magnesium acetate. The third method employed the total experimental mass loss of both decomposition reactions. The results obtained using this method compared well to the actual values, giving a R ² value of more than 0.99. This method of using the total mass losses can however only be used for binary mixtures that consist only of magnesium hydroxide and magnesium acetate. This revised version was published online in August 2006 with corrections to the Cover Date.     

The determination of hydrazine and 1,1-dimethylhydrazine,separately or in mixtures,by high-pressure liquid chromatography

A rapid, sensitive liquid chromatographic method for the determination of hydrazine and 1,1-dimethylhydrazine, separately or in mixtures of varying proportions, is described. The procedure involves salicylaldehyde derivative formation followed by chromatography on a reversed phase (octadecylsilane) column with acetonitrile (52%)—0.14 M potassium dihydrogenphosphate (48%) as a mobile phase and u.v. (254 nm) detection. This system is sensitive to 2 μg ml^-1 of hydrazine and 5 μg ml^-1 of 1,1-dimethylhydrazine and has a relative standard deviation of less than 1%. Monomethylhydrazine forms an unstable salicylaldehyde hydrazone; although it cannot be determined, it can be detected (sensitivity 5 μg ml^-1 ) and does not interfere with quantitative measurement of either hydrazine or 1,1-dimethylhydrazine.     

Stability-indicating methods for the determination of linezolid in the presence of its alkaline-induced degradation products

Three methods are presented for the determination of linezolid in the presence of its alkaline-induced degradation products. The first method was based on separation of linezolid from its alkaline degradation product by TLC followed by densitometric measurement of the spots of intact drug at 244 nm. The separation was carried out on silica gel 60 F₂₅₄ using isobutanol:ammonia (9:1 v/v) as a mobile phase. The second method was based on first derivative ¹D ultraviolet spectrophotometry with zero crossing point and peak to base measurement. The ¹D value at 251.4 nm was selected for the assay of linezolid in the presence of degradation product. The third method was depended on the first derivative of the ratio spectra ¹DD by measurement of the value at 263.6 nm. The proposed methods were successfully applied to the determination of the drug in bulk powder, in laboratory prepared mixtures with its degradation product and in commercial tablets.     

Simultaneous determination of iron and ruthenium by preconcentration on sulfopropyl sephadex cation exchanger

A new method for the simultaneous determination of iron and ruthenium at ultra-trace levels is proposed. The method is based on the formation of the iron and ruthenium complexes with 2,4,6-tri-(2-pyridil)-1,3,5-triazine (TPTZ) in the presence of hydroxylamine hydrochloride and buffer CH₂ClCOOH/CH₂ClCOONa (pH=3.0). The formation of the complexes and their retention on a cationic resin SP-Sephadex C25 were integrated in one step at 90 °C, with stirring for 90 min. Under these conditions a high preconcentration level was achieved for both analytes. The complexes retained on the solid phase were evaluated by second derivative spectrophotometry. The selected analytical wavelengths were 539.7 and 553.3 nm for the determination of ruthenium and iron, respectively, by using the zero crossing approach. The detection and quantification limits were 0.54 ng ml⁻¹ and 1.79 ng ml⁻¹ for ruthenium and 0.41 ng ml⁻¹ and 1.38 ng ml⁻¹ for iron. The proposed method was applied to the determination of both analytes in synthetic mixtures.     

Three-dimensional synchronous fluorimetric determination of indole-type auxins after derivatization with o-phthalaldehyde

A sensitive fluorimetric method for teh determination of indole-derivative plant-growth regulators of the auxin group (indole-3-acetic acid, indole-3-butyric acid and indole-3-propanoic acid) is based on their eaction with o-phthaladehyde in concentrated sulphuric acid. The fluorescence spectra of the three derivatives are very similar, but the advantages offered by a three-dimensional plot of the spectra, the synchronous derivative approach and the optimization of experimental variables permit the individual and simultaneous quantitation of mixtures of these compounds at the ng ml^-1 level.     

Ratio-Spectra Zero-Crossing Derivative Spectrophotometric Determination of Certain Drugs in Two-Component Mixtures

ABSTRACT

Two two-component mixtures have been assayed using both Vierordt's method and ratio-spectra zero-crossing derivative spectrophotometric methods. Such mixtures are hydrochlorothiazide-spironolactone and hydrochlorothiazide-ramipril. These selected applications illustrate the relative ease and simplicity offered by ratio - spectra zero - crossing derivative spectrophotometry for the assay of two component mixtures with spectral interferences from matrix formulations.     

Second Derivative Spectrophotometric Determination of p-Aminophenol in the Presence of Paracetamol

Abstract

A second derivative spectroscopic method for the determination of p-aminophenol in paracetamol powder is described. Second derivative absorbance (d²A/dλ²) values were measured at 223.8 nm (Δ = 4.2 nm) where p-aminophenol showed derivative responses obeying Beer's Law but paracetamol had negligible derivative absorption. The concentrations of p-aminophenol solutions prepared in 0.1 N HCl (0.12–7.61 mcg/ml), containing constant amounts of paracetamol (20 mcg/ml) related linearly with the d²A/dλ² values and gave a straight line (r = ?0.9999). The method allowed determination of 0.5% to 38% of p-aminophenol in paracetamol without prior separation, it is rapid, precise and accurate.