Inhibition effect of 1-ethyl-3-methylimidazolium chloride on methane hydrate equilibrium

The dissociation conditions of methane hydrate in the presence of 0.1, 0.2, 0.3 and 0.4 mass fraction of 1-ethyl-3-methylimidazolium chloride (abbreviated by EMIM-Cl hereafter) were experimentally determined. A high pressure micro-differential scanning calorimeter equipped with a motorized pump was applied to measure the dissociation temperature of the (hydrate + liquid water + vapor) three-phase equilibrium under a constant pressure process with a pressure ranging from (5.0 to 35.0) MPa. The addition of EMIM-Cl would inhibit the methane hydrate formation. The most significant inhibition effect was observed at 0.4 mass fraction of EMIM-Cl in aqueous solution to lower the dissociation temperature by 12.82 K at 20.00 MPa in comparison to that of the (methane + water) system. The Peng–Robinson–Stryjek–Vera equation of state incorporated with COSMO-SAC activity coefficient model and the first order modified Huron–Vidal mixing rule were applied to evaluate the fugacity of vapor and liquid phase. A modified van der Waals and Platteeuw model with an explicit pressure dependence of the Langmuir adsorption constant was applied to determine the fugacity of hydrate phase. The predictive thermodynamic model successfully describes the tendency of phase behavior of methane hydrate in the presence of EMIM-Cl in the range from 0.1 to 0.4 mass fraction with absolute average relative deviation in predicted temperature of 0.70%.     

Hydrate phase equilibrium and structure for (methane + ethane + tetrahydrofuran + water) system

The separation of methane and ethane through forming hydrate is a possible choice in natural gas, oil processing, or ethylene producing. The hydrate formation conditions of five groups of (methane + ethane) binary gas mixtures in the presence of 0.06 mole fraction tetrahydrofuran (THF) in water were obtained at temperatures ranging from (277.7 to 288.2) K. In most cases, the presence of THF in water can lower the hydrate formation pressure of (methane + ethane) remarkably. However, when the composition of ethane is as high as 0.832, it is more difficult to form hydrate than without THF system. Phase equilibrium model for hydrates containing THF was developed based on a two-step hydrate formation mechanism. The structure of hydrates formed from (methane + ethane + THF + water) system was also determined by Raman spectroscopy. When THF concentration in initial aqueous solution was only 0.06 mole fraction, the coexistence of structure I hydrate dominated by ethane and structure II hydrate dominated by THF in the hydrate sample was clearly demonstrated by Raman spectroscopic data. On the contrary, only structure II hydrate existed in the hydrate sample formed from (methane + ethane + THF + water) system when THF concentration in initial aqueous solution was increased to 0.10 mole fraction. It indicated that higher THF concentration inhibited the formation of structure I hydrate dominated by ethane and therefore lowered the trapping of ethane in hydrate. It implies a very promising method to increase the separation efficiency of methane and ethane.     

Phase behaviour of mixed-gas hydrate systems containing carbon dioxide

We describe a new apparatus suitable for measurements of the phase behaviour and phase properties of fluid mixtures under conditions of high-pressure. We propose a synthetic method for the determination of gas solubility, and present results for the system (CO₂ + H₂O). In addition, we report new measurements of the hydrate equilibrium curves in aqueous systems containing either pure carbon dioxide or mixed gases including CO₂. For hydrates formed in the (CO₂ + H₂O) system, we find an enthalpy of dissociation of 77 kJ · mol^?1. This value was unchanged by the addition of mass fraction 0.043 of NaCl to the water. Compared with pure CO₂, mixtures of CO₂ with air exhibited markedly different dissociation pressures at given temperature, but were characterised by the same enthalpy of dissociation. However, two mixtures containing either nitrogen or methane and hydrogen both exhibited a higher enthalpy of dissociation, 106 kJ · mol^?1, consistent with these systems forming structure II hydrates.     

Measurements of methane hydrate equilibrium in systems inhibited with NaCl and methanol

Natural gas hydrates are ice-like inclusion compounds that form at high pressures and low temperatures in the presence of water and light hydrocarbons. Hydrate formation conditions are favorable in gas and oil pipelines, and their formation threatens gas and oil production. Thermodynamic hydrate inhibitors (THIs) are chemicals (e.g., methanol, monoethylene glycol) deployed in gas pipelines to depress the equilibrium temperature required for hydrate formation. This work presents a novel application of a stepwise differential scanning calorimeter (DSC) measurement to accurately determine the methane hydrate phase boundary in the presence of THIs. The scheme is first validated on a model (ice + salt water) system, and then generalized to measure hydrate equilibrium temperatures for pure systems and 0.035 mass fraction NaCl solutions diluted to 0, 0.05, 0.10, and 0.20 mass fraction methanol. The hydrate equilibrium temperatures are measured at methane pressures from (7.0 to 20.0) MPa. The measured equilibrium temperatures are compared to values computed by the predictive hydrate equilibrium tool CSMGem.     

Phase equilibrium measurements for semi-clathrate hydrates of the (CO2 + N2 + tetra-n-butylammonium bromide) aqueous solution system

The application of semi-clathrate hydrate formation technology for gas separation purposes has gained much attention in recent years. Consequently, there is a demand for experimental data for relevant semi-clathrate hydrate phase equilibria. In this work, semi-clathrate hydrate dissociation conditions for the system comprising mixtures of {CO₂ (0.151/0.399 mole fraction) + N₂ (0.849/0.601 mole fraction) + 0.05, 0.15, and 0.30 mass fraction tetra-n-butylammonium bromide (TBAB)} aqueous solutions have been measured and are reported. An experimental apparatus which was designed and built in-house was used for the measurements using the isochoric pressure-search method. The range of conditions for the measurements was from 277.1 K to 293.2 K for temperature and pressures up to 16.21 MPa. The phase equilibrium data measured demonstrate the high hydrate promotion effects of TBAB aqueous solutions.     

Enthalpies of dissociation of clathrate hydrates of carbon dioxide,nitrogen, (carbon dioxide + nitrogen), and (carbon dioxide + nitrogen + tetrahydrofuran)

A calorimetric technique is described for measuring the enthalpy of dissociation liberated from solid hydrates. In this study, the enthalpies of dissociation were determined at T =  273.65 K andp =  0.1 MPa for simple and mixed hydrates of carbon dioxide, nitrogen, (carbon dioxide  +  nitrogen), and (carbon dioxide  +  nitrogen  +  tetrahydrofuran) using an isothermal microcalorimeter. The addition of tetrahydrofuran (THF) promoted hydrate stability and increased the number of guest molecules encaged in the small and large cavities of the hydrate lattice, resulting in lower enthalpy of dissociation, compared with structure II hydrate. The composition ratio of guest molecules did not affect the enthalpy of dissociation, which was found to be nearly constant for the same mixture.     

Effect of ionic liquids on (vapor + liquid) equilibrium behavior of (water + 2-methyl-2-propanol)

Isobaric T, x, y data were reported for ternary systems of {water + 2-methyl-2-propanol (tert-butyl alcohol, TBA) + ionic liquid (IL)} at p = 100 kPa. When the mole fraction of TBA on IL-free basis was fixed at 0.95, measurements were performed at IL mass fractions from 0.6 down to 0.05, in a way of repeated synthesis. The vapor-phase compositions were obtained by analytical methods and the liquid-phase compositions were calculated with the aid of mass balances. Activity coefficients of water and TBA were obtained without the need of a thermodynamic model of the liquid-phase. Six ILs, composed of an anion chosen from [OAc]^? or [Cl]^?, and a cation from [emim]⁺, or [bmim]⁺, or [hmim]⁺, were studied. Relative volatility and activity coefficients were presented in relation with the IL mole fraction, showing the effect of the ILs on a molar basis. The effect of the ILs on relative volatility of TBA to water was depicted by the effect of anions and cations on, respectively, the activity coefficients of water and TBA. The results indicated that, among the six ILs studied, [emim][Cl] has the most significant effect on enhancement of the relative volatility, which reaches a value of 7.2 at an IL mass fraction of 0.58. Another IL, [emim][OAc], has also significant effect, with an appreciable value of 5.2 for the relative volatility when the IL mass fraction is 0.6. Considering the relatively low viscosity and melting point of [emim][OAc], it might be a favorable candidate as solvent for the separation of water and TBA by extractive distillation. Simultaneous correlation by the NRTL model was presented for both systems of (water + ethanol + IL) and (water + TBA + IL), using consistent binary parameters for water and IL.     

Experimental study and thermodynamic modelling of methane clathrate hydrate dissociation conditions in silica gel porous media in the presence of methanol aqueous solution

In this work, the phase equilibria of clathrate hydrates of methane in the presence of pure water and 0.035 mass fraction of methanol aqueous solution in confined silica gel pores with (10 and 15) nm mean diameters are measured and reported. A thermodynamic model is also developed for prediction of the obtained experimental hydrate dissociation data. The Valderrama–Patel–Teja (VPT-EoS) equation of state (EoS) accompanied with the non-density dependent (NDD) mixing rules coupled with a previously developed activity model are applied to evaluate the fugacity of the species present and the activity coefficient of water in methanol aqueous solution. Acceptable agreement between the reported data and the predicted results using the proposed model and an existing method reported in the literature demonstrates the reliability of the presented model.     

Hydrate structural transition depending on the composition of methane + cyclopropane mixed gas hydrate

The methane + cyclopropane mixed gas hydrate system has been investigated at 291.1 K by means of gas chromatography and Raman spectroscopy. Both of pure guest species generate the structure-I hydrate in the present conditions. Isothermal phase equilibria exhibit discontinuity around the equilibrium cyclopropane composition (water-free) in the gas phase of 0.20. The Raman shifts have changed bordering at the point. These results reveal that the methane + cyclopropane mixed gas hydrate generates the structure-II crystal in the methane rich region, while the structure-I crystal is generated in the cyclopropane rich region.     

Excess molar volumes of binary mixtures (an ionic liquid + water): A review

This review covers recent developments in the area of excess molar volumes for mixtures of {ILs (1) + H₂O (2)} where ILs refers to ionic liquids involving cations: imidazolium, pyridinium, pyrrolidinium, piperidinium, morpholinium and ammonium groups; and anions: tetraborate, triflate, hydrogensulphate, methylsulphate, ethylsulphate, thiocyanate, dicyanamide, octanate, acetate, nitrate, chloride, bromide, and iodine. The excess molar volumes of aqueous ILs were found to cover a wide range of values for the different ILs (ranging from −1.7 cm³ · mol⁻¹ to 1.2 cm³ · mol⁻¹). The excess molar volumes increased with increasing temperature for all systems studied in this review. The magnitude and in some cases the sign of the excess molar volumes for all the aqueous ILs mixtures, apart from the ammonium ILs, were very dependent on temperature. This was particularly important in the dilute IL concentration region. It was found that the sign and magnitude of the excess molar volumes of aqueous ILs (for ILs with hydrophobic cations), was more dependent on the nature of the anion than on the cation.     

Phase equilibrium measurements and the tuning behavior of new sII clathrate hydrates

We suggest two types of new amine-type sII formers: pyrrolidine and piperidine. These guest compounds fail to form clathrate hydrate structures with host water, but instead have to combine with light gaseous guest molecules (methane) for enclathration. First, two binary clathrate hydrates of (pyrrolidine + methane) and (piperidine + methane) were synthesized at various amine concentrations. ¹³C NMR and Raman analysis were done to identify the clathrate hydrate structure and guest distribution over sII-S and sII-L cages. XRD was also used to find the exact structure and corresponding cell parameters. At a dilute pyrrolidine concentration of less than 5.56 mol%, the tuning phenomenon is observed such that methane molecules surprisingly occupy sII-L cages. At the critical guest concentration of about 0.1 mol%, the cage occupancy ratio reaches the maximum of approximately 0.5. At very dilute guest concentration below 0.1 mol%, the methane molecules fail to occupy large cages on account of their rarefied distribution in the network. Direct-release experiments were performed to determine the actual guest compositions in the clathrate hydrate phases. Finally, we measured the clathrate hydrate phase equilibria of (pyrrolidine + methane) and (piperidine + methane).     

Isothermal phase equilibria for the (xenon + cyclopropane) mixed-gas hydrate system

Isothermal three-phase equilibria of gas, aqueous, and hydrate phases for the {xenon (Xe) + cyclopropane (c-C₃H₆)} mixed-gas hydrate system were measured at two different temperatures (279.15 and 289.15) K. The structural phase transitions from structure-I to structure-II and back to structure-I, depending on the mole fraction of guest mixtures, occur in the (Xe + c-C₃H₆) mixed-gas hydrate system. The isothermal pressure–composition relations have two local pressure minima. The most important characteristic in the (Xe + c-C₃H₆) mixed-gas hydrate system is that the equilibrium pressure–composition relations exhibit the complex phase behavior involving two structural phase transitions and two homogeneous negative azeotropes. One of two structural phase transitions exhibits the heterogeneous azeotropic-like behavior.     

Experimental measurement and thermodynamic modelling of phase equilibria of semi-clathrate hydrates of (CO2 + tetra-n-butyl-ammonium bromide) aqueous solution

Comprehensive studies on semi-clathrate hydrates phase equilibria are still required to better understand characteristics of this type of clathrates. In this communication, new experimental data on the dissociation conditions of semi-clathrate hydrates of {carbon dioxide + tetra-n-butyl-ammonium bromide (TBAB)} aqueous solution are first reported in a wide range of TBAB concentrations and at different pressures and temperatures. A thermodynamic model is then proposed to predict the dissociation conditions of the semi-clathrate hydrates for the latter system. The (hydrate + TBAB) aqueous solution (H + L_w) phase equilibrium prediction is considered based on Gibbs free energy minimization approach. A modified van der Waals–Platteeuw solid solution theory developed based on the (H + L_w) equilibrium information is employed to predict the dissociation conditions of semi-clathrate hydrates of carbon dioxide + TBAB. The properties of the aqueous solution are estimated using the AMSA-NRTL electrolyte model (considering the association and hydration of ions). The Peng–Robinson equation of state is used for estimating the gas/vapour phase properties. Results show that the proposed model satisfactorily predicts the experimental values with an average absolute relative deviation of approximately 13%.     

Kinetic and thermodynamic behaviour of CF4 clathrate hydrates

This study presents experimental kinetic and thermodynamic data for CF₄ clathrate hydrates. Experimental measurements were undertaken in a high pressure equilibrium cell with a 40 cm³ inner volume. The measurements of experimental hydrate dissociation conditions were performed in the temperature range of (273.8 to 278.3) K and pressures ranging from (4.55 to 11.57) MPa. A thermodynamic model based on van der Waals and Platteeuw (vdW–P) solid solution theory was used for prediction and comparison of hydrate dissociation conditions and the Langmuir constant parameters for CF₄ based on Parrish and Prausnitz equation are reported. For the kinetics, the effect of initial pressure and temperature on the induction time, CF₄ hydrate formation rate, the apparent rate constant of reaction, storage capacity, and water to hydrate conversion during the hydrate formation were studied. Kinetic experiments were performed at initial temperatures of (275.3, 276.1 and 276.6) K and initial pressures of (7.08, 7.92, 9.11, 11.47 and 11.83) MPa. Results show that increasing the initial pressure at constant temperature decreases the induction time, while CF₄ hydrate formation rate, the apparent rate constant of reaction, storage capacity, and water to hydrate conversion increase. The same trends are observed with a decrease in the initial temperature at constant pressure.     

Thermodynamic stability of structure-H hydrates of methylcyclopentane and cyclooctane helped by methane

The four-phase equilibria were measured for the methylcyclopentane+methane+H₂O hydrate system (274.28–287.40 K, 1.75–9.34 MPa) and the cyclooctane+methane+H₂O hydrate system (274.08–288.57 K, 1.60–9.33 MPa). Each structure-H hydrate has the lower equilibrium pressure than the pure methane structure-I hydrate in the temperature range of the present work. The isothermal equilibrium pressures of both methylcyclopentane and cyclooctane hydrates are slightly higher than that of methylcyclohexane hydrate.     

Experimental low temperature water content in gaseous methane,liquid ethane,and liquid propane in equilibrium with hydrate at cryogenic conditions

In low temperature gas processing, the presence of water can result in the formation of gas hydrate plugs. To avoid this problem, it is important to know the water solubility in natural gas components in equilibrium with gas hydrate. In this study experimental measurements of water content in gaseous methane in equilibrium with hydrate at 3.45 MPa (500 psia) and 6.90 MPa (1000 psia) and temperatures ranging from −3.2 °C (26.2 °F) to −80 °C (−112 °F) are presented. Similar measurements are presented for liquid ethane at 3.45 MPa (500 psia) and temperatures from −2.2 °C (28.0 °F) to −70 °C (−94 °F), and for liquid propane at 0.86 MPa (125 psia) and temperatures down to −60 °C (−76 °F), respectively.In measuring the water content, a Panametrics moisture sensor (calibrated to 1 ppb water content in nitrogen) has been used in flowing streams of the hydrocarbon-rich phases that are saturated with water. The results obtained with the Panametrics hygrometer show good agreement (normally better than ±4%) with previous measurements, which were obtained by a gas chromatographic technique for methane, ethane, and propane at temperatures ranging from −2.0 °C (28.4 °F) to −30 °C (−22 °F), which are within the hydrate region.     

Phase equilibria study of the binary systems (ionic liquid + thiophene): Desulphurization process

(Solid + liquid) equilibria (SLE) and (liquid + liquid) equilibria (LLE) for the binary systems: {ionic liquid (IL) N-butyl-4-methylpyridinium tosylate (p-toluenesulfonate) [BM⁴Py][TOS], or N-butyl-3-methylpyridinium tosylate [BM³Py][TOS], or N-hexyl-3-methylpyridinium tosylate [HM³Py][TOS], or N-butyl-4-methylpyridinium bis{(trifluoromethyl)sulfonyl}imide [BM⁴Py][NTf₂], or 1,4-dimethylpyridinium tosylate [M^1,4Py][TOS], or 2,4,6-collidine tosylate [M^2,4,6Py][TOS], or 1-ethyl-3-methylimidazolium thiocyanate [EMIM][SCN], or 1-butyl-3-methylimidazolium thiocyanate [BMIM][SCN], or 1-hexyl-3-methylimidazolium thiocyanate [HMIM][SCN], or triethylsulphonium bis(trifluoromethylsulfonyl)imide [Et₃S][NTf₂] + thiophene} have been determined at ambient pressure. A dynamic method was used over a broad range of mole fractions and temperatures from (270 to 390) K. In the case of systems (pyridinium IL, or sulphonium IL + thiophene) the mutual immiscibility with an upper critical solution temperature (UCST) was detected at the very narrow and low mole fraction of the IL. For the binary systems containing (imidazolium thiocyanate IL + thiophene), the mutual immiscibility with the lower critical solution temperature (LCST) was detected at the higher mole fraction range of the IL. The basic thermal properties of the pure ILs, i.e. melting and glass-transition temperatures as well as the enthalpy of fusion have been measured using a differential scanning microcalorimetry technique (DSC). The well-known NRTL equation has been used to correlate experimental SLE/LLE data sets.     

Use of selective ionic liquids and ionic liquid/salt mixtures as entrainer in a (vapor + liquid) system to separate n-heptane from toluene

During the last years, a large number of studies have evaluated the ability of ionic liquids (ILs) to separate aromatic from aliphatic hydrocarbons by liquid extraction. Nevertheless, in order to design a global process, a post-extraction step based on the aromatic recovery from the extract stream and the regeneration of the IL is required. Taking into account the negligible vapor pressure of the ILs, the use of separation units based on the difference of volatility among the components of the extract could be an appropriate way. However, that requires additional (vapor + liquid) equilibrium (VLE) data, which are scarce today. In this work, the isothermal VLE data for {n-heptane + toluene + 1-ethyl-3-methylimidazolium thiocyanate ([EMim][SCN])} and {n-heptane + toluene + 1-butyl-3-methylimidazolium thiocyanate ([BMim][SCN])} mixtures were experimentally measured at T = (323.2, 343.2 and 363.2) K over the whole composition range within the rich-IL miscibility region. For that, a static headspace gas chromatograph (HS-GC) was used. In addition, the non-random two liquids (NRTL) thermodynamic model was satisfactory applied to correlate the experimental VLE data.Finally, the effect of thiocyanate-based inorganic salts (AgSCN, Co(SCN)₂ and CuSCN) on the phase behavior of the above mentioned mixtures were also analyzed through the experimental determination of the isothermal VLE of the pseudo-ternary systems {n-heptane + toluene + [EMim][SCN]/salt mixture}.The obtained results show that the use of pure thiocyanate-based ILs as entrainer increases the n-heptane relative volatility from toluene whereas the addition of inorganic salts has not led to an improvement of these results.     

An electrically heated ionic-liquid/multi-wall carbon nanotube composite electrode and its application to electrochemiluminescent detection of ascorbic acid

A heated composite electrode consisted of multi-wall carbon nanotube (MWNT) and ionic liquids (ILs) was designed and fabricated. The non-conductive binders were replaced by a conductive IL, n-octylpyridinum hexafluorophosphate (OPFP). This heated OPFP/MWNT composite electrode was applied for electrochemiluminescent (ECL) sensor, and the performance of ECL sensor was evaluated by ascorbic acid (AA)/lucigenin ECL system. The new heated electrode combines the advantages of ILs/CNT and heated electrode, showing high thermal stability and conductivity, simple heating setups, improved reproducibility, renewable surface, simplicity of fabrication and enhanced sensitivity with detection limit (S/N = 3) of 0.01 μmol/L for AA.