Detection of nitrated benzodiazepines by indirect laser-induced fluorescence detection on a microfluidic device

Recently there has been concern regarding the use of flunitrazepam and other low-dose benzodiazepines in drug-facilitated sexual assault. These compounds are placed in drinks of unsuspecting victims and produce a sedative effect with anterorgrade amnesia. Chip-based microfluidic systems can provide a quick and disposable procedure for the detection of flunitrazepam and other nitrated benzodiazepines used in these crimes. This paper describes the application of indirect quenching of cyanine dye (Cy5) for detection of nitrated benzodiazepines. The separation is performed on a microfluidic device with a separation channel 8 cm long and 50 microm wide and utilizes indirect fluorescence detection with 635 nm laser excitation. The optimization of the separation using micellar electrokinetic chromatography with organic modifiers is described. A borate buffer containing 2.6 microM Cy5 dye, 15 mM sodium dodecyl sulphate (SDS) and 20% methanol is used. Complete separation of four target drugs occurs in under 2 min with limits of detection in the low microg/ml range. Overall the method provides a rapid and simple analysis for the presence of nitrated benzodiazepines in beverages and other similar preparations.     

Separation of sympathomimetic amines of abuse and related compounds by micellar electrokinetic chromatography.

Separation of twelve sympathomimetic amines and related compounds by micellar electrokinetic chromatography (MEKC) with UV absorbance detection is described. These amines were well separated within 25 min using 50 mM sodium tetraborate solution containing 15 mM sodium dodecylsulfate (SDS) of pH 9.3 as a running solution and detected at 210 nm. MEKC was performed with an applied voltage of 13 kV at 25 degrees C using a fused-silica capillary (50 cm x 75 mm i.d.) with effective length of 37.5 cm. The detection limits of these compounds were in the range from 4 to 97 fmol/injection at a signal-to-noise ratio (S/N) of 3. The reproducibility of the method expressed as relative standard deviation (RSD) for within-day (n=6) and between-day (n=5) assays was less than 4.8 and 8.8%, respectively. The proposed method could be applied to the determination of an anorectic drug, phentermine, in Chinese tea with a detection limit of 99 microg/g (105 fmol/injection, S/N=3).     

Determination of Diazepam and associated compounds in pharmaceutical preparations

A method for determining Diazepam and its associated compounds in pharmaceutical products by micellar electrokinetic chromatography (MEKC) is described. The separation was carried out at 30?°C and 25 kV, using a 25 mM borate buffer (pH 9.6) and 35 mM sodium dodecylsulfate (SDS) water solution. Under these conditions the analysis was carried out within 12 min with acceptable limits of detection and quantification. The method has been applied for quantifying Diazepam in different commercial formulations when it is the active drug and when it is employed associated with other drugs (Nortriptyline, Pyridoxine hydrochloride and Sulpiride).     

Determination of Diazepam and associated compounds in pharmaceutical preparations

A method for determining Diazepam and its associated compounds in pharmaceutical products by micellar electrokinetic chromatography (MEKC) is described. The separation was carried out at 30 °C and 25 kV, using a 25 mM borate buffer (pH 9.6) and 35 mM sodium dodecylsulfate (SDS) water solution. Under these conditions the analysis was carried out within 12 min with acceptable limits of detection and quantification. The method has been applied for quantifying Diazepam in different commercial formulations when it is the active drug and when it is employed associated with other drugs (Nortriptyline, Pyridoxine hydrochloride and Sulpiride). Received: 30 October 1998 / Revised: 1 February 1999 / Accepted: 3 February 1999     

Analysis of clindamycin by micellar electrokinetic chromatography with a mixed micellar system.

This study details the development and validation of an optimized method with micellar electrokinetic chromatography for the analysis of clindamycin. The method uses a mixed micellar phase containing anionic sodium dodecylsulfate (SDS) and non ionic Brij 35 on an untreated fused-silica capillary. The influences of buffer concentration, pH, SDS, Brij 35 and organic modifier were investigated. Special attention was given to the role of the non ionic Brij 35 in the mixed micellar system. Optimization with a central composite design resulted in optimal separation conditions: background electrolyte containing 25 mM sodium tetraborate pH 7.75, 90 mM SDS, 14 mM Brij 35 and 21% acetonitrile. The applied voltage was 15 kV and the capillary temperature 15 degrees C. The method was robust and gave good linearity and repeatability. The limits of detection and quantitation were 0.05 and 0.15%, respectively, relative to a 2.5 mg/ml clindamycin solution. Two commercial bulk products were analysed with this system.     

Separation of serum bilirubin species by micellar electrokinetic chromatography with direct sample injection.

Four major bilirubin species in serum were separated by micellar electrokinetic chromatography with 25 mM sodium dodecyl sulfate (SDS) and 20 mM sodium tetraborate-boric acid buffer at pH 8.5. Due to the solubilization of the serum proteins by the SDS micelles, serum samples were injected directly into a 50 cm x 75 microns I.D. fused-silica capillary and complete separation of the four bilirubin species was accomplished within ca. 10 min without extensive sample pretreatment. Detection was performed by absorbance at 450 nm and average limit of detection was in the 6.0 microM concentration range. The usefulness of this method was demonstrated for the separation and detection of a number of bilirubin species present in pathological human serum samples.     

Analysis of spiramycin by capillary electrophoresis.

The development and validation of an analytical method for the determination of spiramycin I in the presence of its related substances by capillary electrophoresis is shown. The separation, performed in a phosphate buffer (80 mM, pH 7.5) containing 12 mM cetyltrimethylammonium bromide (CTAB) and 20 mM sodium cholate, with a 50 microm ID and 44 cm long fused-silica capillary (36 cm effective length), applying a voltage of 12 kV (l approximately 80 microA), at 25 degrees C, is achieved in 15 min. Good selectivity among spiramycin I and its related substances was obtained. The influence of the buffer pH, and of the CTAB and sodium cholate concentrations was investigated. The method robustness, examined by means of a full-fraction factorial design, shows that it can be used within the limits set for the three parameters that were investigated. The method is linear (r = 0.9992) and precise (day-to-day corrected peak area repeatability, n = 18, relative standard deviation = 1.3%). The limits of detection and quantitation are 7 pg (0.025%) and 22 pg (0.08%), respectively, relative to a 2 mg/mL solution.     

Micellar electrokinetic chromatography of fluorescently labeled proteins on poly(dimethylsiloxane)-based microchips

MEKC of standard proteins was investigated on PDMS microfluidic devices. Standard proteins were labeled with AlexaFluor(R) 488 carboxylic acid tetrafluorophenyl ester and filtered through a size-exclusion column to remove any small peptides and unreacted label. High-efficiency MEKC separations of these standard proteins were performed using a buffer consisting of 10 mM sodium tetraborate, 25 mM SDS, and 20% v/v ACN. A separation of BSA using this buffer in a 3.0 cm long channel generated a peak with a plate height of 0.38 microm in <20 s. Additional fast separations of myoglobin, alpha-lactalbumin, lysozyme, and cytochrome c also yielded peaks with plate heights ranging from 0.54 to 0.72 microm. All proteins migrated with respect to their individual pIs. To improve the separations, we used a PDMS serpentine chip with tapered turns and a separation distance of 25 cm. The number of plates generated increased linearly with increasing separation distance on the extended separation channel chips; however, the resolution reached an asymptotic value after about 7 cm. This limited the peak capacity of the separation technique to 10-12.     

Microemulsion electrokinetic chromatography versus capillary electrochromatography-UV-mass spectrometry for the analysis of flunitrazepam and its major metabolites

Benzodiazepines, namely flunitrazepam and its three major metabolites, were successfully separated by microemulsion electrokinetic chromatography. Separation was achieved using an untreated fused-silica capillary (48 cm (effective length 40 cm) x 50 num) at 25 kV; detection was performed by UV at 220 nm. The microemulsion system consisted of 70 mM octane, 800 mM 1-butanol, 80 mM sodium dodecyl sulfate (SDS) and 10 mM borate buffer, pH 9. Very high efficiencies (up to 400 000 plates) and resolution better than 3 were achieved. Since this technique is not compatible with mass spectrometry (MS) detection, a capillary electrochromatographic (CEC) method was developed to separate flunitrazepam and its metabolites. The effects of mobile phase composition and pH as well as voltage and temperature were systematically investigated. The optimized CEC method allowed the baseline separation of the investigated compounds. For the on-line coupling of CEC with electrospray ionization-mass spectrometry, the column was connected to a void fused-silica capillary using a Teflon connection. This configuration was found efficient and suitable for hyphenation of commercial CEC and MS instrumentation using commercially available CEC columns.     

Protein separation and surfactant control of electroosmotic flow in poly(dimethylsiloxane)-coated capillaries and microchips

A thermally pyrolyzed poly(dimethylsiloxane) (PDMS) coating intended to prevent surface adsorption during capillary electrophoretic (CE) [Science 222 (1983) 266] separation of proteins, and to provide a substrate for surfactant adsorption for electroosmotic mobility control was prepared and evaluated. Coating fused-silica capillaries or glass microchip CE devices with a 1% solution of 100 cSt silicone oil in CH2Cl2, followed by forced N2 drying and thermal curing at 400 degrees C for 30 min produced a cross-linked PDMS layer. Addition of 0.01 to 0.02% Brij 35 to a 0.020 M phosphate buffer gave separations of lysozyme, cytochrome c, RNase, and fluorescein-labeled goat anti-human IgG Fab fragment. Respective plates/m typically obtained at 20 kV (740 V cm(-1)) were 2, 1.5, 1.25, and 9.4-10(5). In 50 mM ionic strength phosphate, 0.01% Brij 35 running buffer, the electroosmotic flow observed was about 25% of that in a bare capillary, and showed no pH dependence between pH 6.3-8.2. Addition of sodium dodecylsulfate (SDS) or cetyltrimethylammonium bromide (CTAB) to this running buffer allowed ready control of electroosmotic mobility, mu(eo). Concentrations of SDS between 0.005 to 0.1% resulted in mu(eo) ranging from 3 to 5 x 10(-4) cm2 V(-1) s(-1). Addition of 1 to 2.3 x 10(-4)% (2.7-6.3 microM) CTAB caused flow reversal. CTAB concentrations between 3.5 x 10(-4) and 0.05% (0.0014-1.37 mM) allowed control of mu(eo) between -1 x 10(-4) and -5.0 x 10(-4) cm2 V(-1) s(-1). For both surfactants the added presence of 0.01% Brij 35 provided slowly varying changes in mu(eo) with charged surfactant concentration.     

Simultaneous determination of antioxidants, preservatives and sweeteners permitted as additives in food by mixed micellar electrokinetic chromatography.

A micellar electrokinetic chromatography method was developed to simultaneously analyse commonly used food additives. The additive mixture, comprising propyl gallate, octyl gallate, dodecyl gallate, butylated hydroxyanisole, butylated hydroxytoluene, tertiary butylhydroquinone, p-hydroxybenzoic acid methyl ester, p-hydroxybenzoic acid ethyl ester, benzoic acid, sorbic acid, saccharin, aspartame and acesulfame-K, was not resolved using single surfactant micellar systems consisting of sodium dodecyl sulfate (SDS), sodium cholate (SC) or sodium deoxycholate (SDC). The separation of these additives using mixed micellar systems, involving SDS/SC, SDS/SDC and SC/SDC, was investigated. Organic solvents were added to the mixed micellar phases to optimise the separation. The mixture was successfully separated using a 20 mM borate buffer with 35 mM SC, 15 mM SDS and 10% methanol added at pH 9.3. Additives in cola beverages and low-joule jam were investigated and quantified using this method.     

Rapid optimized separation of bromide in serum samples with capillary zone electrophoresis by using glycerol as additive to the background electrolyte

After decades of neglect, bromide has recently been re-introduced in therapy as an effective anti-epileptic drug. The present paper describes the methodological optimization and validation of a method based on capillary zone electrophoresis for the rapid determination of bromide in serum using a high-viscosity buffer and a short capillary (10 cm). The optimized running buffer was composed of 90 mM sodium tetraborate, 10 mM sodium chloride, pH 9.24 and 25% glycerol. The separation was carried out at 25 kV at a temperature of 20 °C. Detection was by direct UV absorption at 200 nm wavelength. The limit of detection (signal-to-noise ratio = 5) in serum was 0.017 mM. The precision of the method was verified in blank serum samples spiked with bromide, obtaining intra-day and day-to-day tests, relative standard deviation values ≤0.2% in terms of migration times and values <2% in terms of peaks areas, respectively.     

1-Butyl-3-methylimidazolium-based ionic liquids and an anionic surfactant: Excellent background electrolyte modifiers for the analysis of benzodiazepines through capillary electrophoresis

In this study, we found that adding 1-butyl-3-methylimidazolium-based ionic liquids (ILs) and sodium dodecyl sulfate (SDS) as modifiers in the background electrolyte (BGE) for capillary electrophoresis enhanced the separation of benzodiazepines. In particular, 1-butyl-3-methylimidazolium bis(trifluoromethanesulfonyl)imide ([BMIM][NTf₂]) was the best IL additive for the separation system because its anionic moiety interacted favorably with the benzodiazepines. We added SDS because of its known effect on the separation of hydrophobic analytes. We optimized the separation conditions in terms of the concentrations of the IL, SDS, and organic solvent, the pH, and the BGE's ionic strength. The optimal BGE, containing 170 mM [BMIM][NTf₂] and 10 mM SDS, provided baseline separation, high efficiency, and satisfactory peak shapes for the benzodiazepines. The separation mechanism was based on heteroassociation between the anionic moiety of the IL and the benzodiazepines, with SDS improving the resolution of the separation. The limits of detection for the seven analytes ranged from 2.74 to 4.42 μg/mL. We subjected a urine sample to off-line solid phase extraction (SPE) prior to the analysis of its benzodiazepine content. Our experimental results reveal that the combination of [BMIM][NTf₂] and SDS provides adequate separation efficiency for its application to CE analyses of benzodiazepines after SPE concentration.     

Rapid separation of barbiturates and benzodiazepines by capillary electrochromatography with 3-(1,8-naphthalimido)propyl-modified silyl silica gel

A capillary electrochromatographic (CEC) method was applied to the simultaneous separation of barbiturates (barbital, phenobarbital, secobarbital and thiopental) and benzodiazepines (nitrazepam, diazepam and triazolam). The separation was performed in a 75 microm i.d. capillary, packed with 3-(1,8-naphthalimido)propyl-modified silyl silica gel (NAIP), studying the effects of buffer pH and mobile phase composition. Using an applied voltage of 20 kV and the short-end injection method (9 cm capillary effective length), the mobile phase of 1.0 mM citrate buffer (pH 5.0) containing 45% methanol provided the baseline separation of seven toxic drugs in less than 9 min. In CEC with NAIP, the benzodiazepines were separated by the combination of hydrophobic and pi-pi interactions, whereas the separation of the barbiturates was based on the hydrophobic interaction.     

Validation of a micellar electrokinetic capillary chromatography method for the determination of imidurea, methyl and propylparabens in a pharmaceutical ointment

The quantitative aspects of a micellar electrokinetic chromatographic (MEKC) method for the determination of three preservatives (imidazolidinyl urea, methyl and propylparabens) in a pharmaceutical ointment are presented. Separation was carried out in a 31.2 cm long (21 cm to the detection window) × 50 μm i.d. fused silica capillary at an electric field of 960 V/cm and 25 °C. The electrolyte was 10 mM sodium dihydrogenophosphate containing 40 mM sodium dodecylsulfate (SDS) and adjusted to pH 6.1. Sample preparation consisted of a simple dispersion of the ointment in an internal standard solution (ethylparaben in the electrolyte). A 3.5 nl volume of the sample solution was introduced hydrodynamically into the capillary. The compounds detected at 200 nm were separated within 1.6 min. The method was validated with respect to specificity, linearity, accuracy, repeatability according to the International Conference on Harmonisation guidelines. Calibration curves were found to be linear for each compound (r²>0.999). Recovery studies performed by spiking an ointment placebo with the preservatives between 50 and 150% of their target concentration on 3 different days gave satisfactory results (mean recovery at each of the five concentrations ranging from 99.23 to 101.40%). The repeatability of sample preparation (n=6) was better than 2% for each of the preservatives.     

Silanizing agent for semipermanent wall coating in micellar electrokinetic capillary chromatography

In this paper, the long-chained, silanizing agent chloro(dodecyl)dimethylsilane (CDDS) was investigated as a semipermanent coating in micellar electrokinetic capillary chromatography (MEKC). CDDS coating had great stability due to the formation of covalent bonding with the silanol groups on the surface of fused-silica capillary and remained stable for over 100 min after removal of the rinse step of CDDS solution. Anionic surfactant sodium dodecyl sulfate (SDS) could aggregate at this CDDS coating by the hydrophobic group and formed a SDS layer which could increase the electroosmotic flow (EOF). The separation was performed with the running buffer composed of 60mM sodium tetraborate, 12 mM SDS at pH 9.9, with the applied voltage of 20 kV and capillary temperature 25 degrees C. The effect of the coating agent was investigated by the analysis of amino acids. Compared with previous no-coating method, the EOF increases from 4.34 x 10(-4)cm(2)V(-1)s(-1) to 7.02 x 10(-4)cm(2)V(-1)s(-1). Migration time reproducibility was less than 0.97% R.S.D. from run to run and less than 1.56% R.S.D. from day to day.     

Separation of related opiate compounds using capillary electrochromatography

Capillary electrophoretic separations have been investigated for six controlled narcotic analgesic compounds having related structures. Owing to the similar charge-to-mass ratios of these compounds, capillary zone electrophoresis failed to provide a satisfactory separation, whereas a baseline-resolved separation was achieved in 10 min using micellar electrokinetic chromatography. Column efficiencies of 40,000-150,000 plates/m were obtained with a 50 cm long, 50 microm inner diameter (ID) capillary using 50 mM sodium dodecyl sulfate (SDS) in a 50 mM borate solution containing 12% isopropanol. In contrast, separation of this mixture by capillary electrochromatography proved to be significantly superior. The capillary was 15 cm long, with an ID of 75 microm, and was packed with 1.5 microm nonporous octadecyl silica (ODS) particles. The mobile phase consisted of 80% 10 mM tris(hydroxymethyl)aminomethane (Tris) and 20% acetonitrile, and contained 5 mM SDS. A complete separation was obtained in 2.5 min with an efficiency of 250,000-500,000 plates/m.     

Effect of surfactant type on surfactant-maltodextrin interactions: isothermal titration calorimetry, surface tensiometry, and ultrasonic velocimetry study

Isothermal titration calorimetry (ITC), surface tensiometry, and ultrasonic velocimetry were used to characterize surfactant-maltodextrin interactions in buffer solutions (pH 7.0, 10 mM NaCl, 20 mM Trizma base, 30.0 degrees C). Experiments were carried out using three surfactants with similar nonpolar tail groups (C12) but different charged headgroups: anionic (sodium dodecyl sulfate, SDS), cationic (dodecyl trimethylammonium bromide, DTAB), and nonionic (polyoxyethylene 23 lauryl ether, Brij35). All three surfactants bound to maltodextrin, with the binding characteristics depending on whether the surfactant headgroup was ionic or nonionic. The amounts of surfactant bound to 0.5% w/v maltodextrin (DE 5) at saturation were < 0.3 mM Brij35, approximately 1-1.6 mM SDS, and approximately 1.5 mM DTAB. ITC measurements indicated that surfactant binding to maltodextrin was exothermic. Surface tension measurements indicated that the DTAB-maltodextrin complex was more surface active than DTAB alone but that SDS- and Brij35- maltodextrin complexes were less surface active than the surfactants alone.     

Examination of colour inkjet printing inks by capillary electrophoresis

The possibility of comparing inkjet printing inks by micellar electrokinetic capillary electrophoresis (MECC) with diode array detection was studied. An analytical procedure was designed and successfully applied to discriminate between the electrophoretic profiles of inks (extracted from paper) produced by five well-known manufacturers. The separation process was conducted in a polyimide-coated fused silica capillary (ID 50 μm, 60 cm total/50 cm effective length) with +30 kV high voltage applied. Background electrolyte was used of the following optimum composition: 40 mM sodium borate buffer, 20 mM sodium dodecyl sulphate(IV) (SDS) and 10% (v/v) acetonitrile (pH 9.56). The experimental conditions were adjusted in terms of resolution and analysis time. The best results were obtained at 10 and 25 °C storage and capillary temperature, respectively, using 25 dots (ø 0.8 mm) cut from printouts as the sample and BGE diluted with water (1:99, v/v) as the injecting solution. The MECC separation of main printing ink components by the proposed method showed excellent precision - the RSD value of the migration time calculated for each of the investigated peaks did not exceed 3.3%. The optimized method was applied to group identification and differentiation of: (a) three colours of printing inks, (b) inks from different manufacturers (Hewlett-Packard, Epson, Brother, Lexmark and Canon) and (c) inks from different printer models. In all these cases, inks were successfully differentiated on the basis of position (migration time) and shape of their characteristic peaks.     

Cyclodextrin-modified microemulsion electrokinetic chromatography for separation of alpha-, gamma-, delta-tocopherol and alpha-tocopherol acetate

Different forms of tocopherols, together with tocotrienols, are collectively named as vitamin E, and each possesses different degree of medical, biological and physiochemical significance. The main difficulty of separating different forms of tocopherols lay in their highly structural similarities and hydrophobicities. Microemulsion electrokinetic chromatography (MEEKC), claimed to attain high peak efficiency with great solubilization power, has not previously been applied to the separation of tocopherols. The effects that various parameters, such as buffer system, type and concentration of cyclodextrins, temperature, and sample matrix, have on the separation of tocopherols by MEEKC have been investigated. By using a buffer mixture of 4% (w/w) sodium dodecyl sulfate (SDS), 6.6% (w/w) 1-butanol, 0.8% (w/w) n-octane, 20% (w/w) 2-propanol, 68.6% (w/w) phosphate (25mM, pH 2.5), and 25mM heptakis(2,6-di-O-methyl)-beta-cyclodextrin (DM-beta-CD), the separation of alpha-, gamma-, and delta-tocopherol, alpha-tocopherol acetate, as well as the antioxidant butylated hydroxytoluene (BHT) at -26kV, 25 degrees C was completed within 35min. The practical potential of the present approach has been further validated by the determination of tocopherols in a vitamin E preparation, with the result of 132.63 (RSD 1.25%), 176.51 (RSD 0.29%), and 64.32mg (RSD 3.34%) per 500mg capsule for alpha-, gamma- and delta-tocopherol, respectively.