Nonsimilar Boundary Layer Analysis of Free Convection Heat Transfer Over a Vertical Cylinder in Bidisperse Porous Media

This work presents a boundary layer analysis for the free convection heat transfer from a vertical cylinder in bidisperse porous media with constant wall temperature. A boundary layer analysis and the two-velocity two-temperature formulation are used to derive the nonsimilar governing equations. The transformed governing equations are solved by the cubic spline collocation method to yield computationally efficient numerical solutions. The effects of inter-phase heat transfer parameter, modified thermal conductivity ratio, and permeability ratio on the heat transfer and flow characteristics are studied. Results show that an increase in the modified thermal conductivity ratio and the permeability ratio can effectively enhance the free convection heat transfer of the vertical cylinder in a bidisperse porous medium. Moreover, the thermal nonequilibrium effects are strong for low values of the inter-phase heat transfer parameter.     

Analytische Untersuchung von freier Konvektion und Filmsieden in laminaren Grenzschichten mit temperaturabhÄngigen Stoffwerten

A two-dimensional, stationary boundary layer modell is derived which allows the treatment of free convection and film boiling on vertical plate and horizontal cylinder under complete consideration of temperature dependent thermophysical properties. Some qualities of these boundary layer solutions are discussed by eleminating the influences of geometry. For horizontal cylinders, a correction of heat transfer for small diameters is given.     

Non-darcy natural convection on a vertical cylinder in a saturated porous medium

The steady free convection boundary layer flow of non-Darcy fluid along an isothermal vertical cylinder embedded in a saturated porous medium using the Ergun model has been studied. The partial differential equations governing the flow have been solved numerically using an implicit finite-difference scheme developed by Keller. It is found that the heat transfer is strongly affected by the modified Grashof number which characterizes the non-Darcy fluid, and the curvature parameter. Also the heat transfer is found to be more than that of the flat plate.     

Unsteady natural convective flow past a moving vertical cylinder with heat and mass transfer

Transient natural convection boundary layer flow of an incompressible viscous fluid past an impulsively moving semi- infinite vertical cylinder is considered. The temperature and concentration of the cylinder surface are taken to be uniform. The unsteady, nonlinear and coupled governing equations of the flow are solved using an implicit finite difference scheme. The finite difference scheme is unconditionally stable and accurate. Numerical results are presented with various sets of parameters for both air and water. Transient effects of velocity, temperature and concentration profiles are analyzed. Local and average skin friction, rates of heat and mass transfer are shown graphically. Received on 1 November 1999     

Heat transfer on a cylinder in accelerated slip flow

The axisymmetric laminar boundary layer flow along the entire length of a semi-infinite stationary cylinder under an accelerated free-stream is investigated. Considering flow at reduced dimensions, the boundary layer equations are developed with the conventional no-slip boundary condition for tangential velocity and temperature replaced by a linear slip-jump boundary condition. Asymptotic series solutions are obtained for the heat transfer coefficient in terms of the Nusselt number. These solutions correspond to prescribed values of the momentum and temperature slip coefficients and the index of acceleration. Heat transfer at both small and large axial distances is determined in the form of series solutions; whereas at intermediate distances, exact and interpolated numerical solutions are obtained. Using these results, the heat transfer along the entire cylinder wall is evaluated in terms of the parameters of acceleration and slip.     

Conjugate free convection over a vertical slender hollow cylinder embedded in a porous medium

A numerical study of the steady conjugate free convection over a vertical slender, hollow circular cylinder with the inner surface at a constant temperature and embedded in a porous medium is reported. The governing boundary layer equations for the fluid-saturated porous medium over the cylinder along with the one-dimensional heat conduction equation for the cylinder are cast into dimensionless form, by using a non-similarity transformation. The resulting non-similarity equations with their corresponding boundary conditions are solved by using the Keller box method. Emphasis is placed on the effects caused by the wall conduction parameter, p, and calculations have covered a wide range of this parameter. Heat transfer results including the temperature profiles, the interface temperature profiles and the local Nusselt number are presented. Received on 17 November 1997     

Analytical study of heat transfer from circular cylinder in liquid metals

In this study the influence of a thin hydrodynamic boundary layer on the heat transfer from a single circular cylinder in liquid metals having low Prandtl number (0.004–0.03) is investigated under isothermal and isoflux boundary conditions. Two separate analytical heat transfer models, viscous and inviscid, are developed to clarify the discrepancy between previous results. For both models, integral approach of the boundary layer analysis is employed to derive closed form expressions for the calculation of the average heat transfer coefficients. For an inviscid model, the energy equation is solved using potential flow velocity only whereas for a viscous model, a fourth-order velocity profile is used in the hydrodynamic boundary layer and potential flow velocity is used outside the boundary layer. The third-order temperature profile is used inside the thermal boundary layer for both models. It is shown that the inviscid model gives higher heat transfer coefficients whereas viscous flow model gives heat transfer results in a fairly good agreement with the previous experimental/numerical results.     

Theoretical analysis of laminar film condensation in a rotating cylinder with a scraper

The rimming film condensation on the inside wall of a rotating cylinder with a scraper is analyzed. The whole cylinder is divided into two regions, one is the so-called boundary layer region where the radial velocity of the condensate is much smaller than the peripheric velocity so that the boundary layer theory is assumed to be valid; the other is the scraper region where because of the disturbance of the scraper the boundary layer theory does not apply. The boundary layer integral method in the boundary layer region coupling with the integral momentum theorem across the scraper region provides a method to determine the velocity, temperature, and film thickness distributions, and heat transfer coefficients. An extensive discussion about the previous models is given. The sublayer flow rate constancy principle and the variability principle of the boundary layer thickness (therefore the interface velocity) at the scraper position with respect to the rotational speed are proposed. The present model greatly improved the prediction of the average heat transfer coefficient. Received on 5 January 1998     

Modeling of the flow structure and heat transfer in a gas-droplet turbulent boundary layer

A numerical study of dynamics and heat/mass transfer in a gas-droplet turbulent boundary layer on a vertical flat plate is carried out. A large number of factors which affect the heat and mass transfer and the structure of thermal and concentration fields in a turbulent boundary layer is analyzed. It is shown that the increase in droplet concentration results in the intensification of heat transfer, as compared with the single-phase air flow. The comparison of this analysis with experimental data shows a qualitative and quantitative agreement between the calculated and experimental data.     

Forced Convection Heat Transfer from a Finite-Height Cylinder

This paper presents a large eddy simulation of forced convection heat transfer in the flow around a surface-mounted finite-height circular cylinder. The study was carried out for a cylinder with height-to-diameter ratio of 2.5, a Reynolds number based on the cylinder diameter of 44 000 and a Prandtl number of 1. Only the surface of the cylinder is heated while the bottom wall and the inflow are kept at a lower fixed temperature. The approach flow boundary layer had a thickness of about 10% of the cylinder height. Local and averaged heat transfer coefficients are presented. The heat transfer coefficient is strongly affected by the free-end of the cylinder. As a result of the flow over the top being downwashed behind the cylinder, a vortex-shedding process does not occur in the upper part, leading to a lower value of the local heat transfer coefficient in that region. In the lower region, vortex-shedding takes place leading to higher values of the local heat transfer coefficient. The circumferentially averaged heat transfer coefficient is 20 % higher near the ground than near the top of the cylinder. The spreading and dilution of the mean temperature field in the wake of the cylinder are also discussed.     

Heat transfer in non-Newtonian falling liquid film on a horizontal circular cylinder

 This study aims to investigate numerically the laminar flow and heat transfer in a pseudoplastic non-Newtonian falling liquid film on a horizontal cylinder for the constant heat flux and isothermal boundary conditions. The inertia terms are taken into account. An implicit finite difference method is carried out to solve the governing boundary layer equations. The effects of operational parameters on the hydrodynamic and heat transfer characteristics are examined and discussed in detail. The results presented show that the local and average Nusselt numbers varies significantly as a function of the concentration of aqueous carboxymethylcellulose (CMC) solutions and the cylinder diameter. Higher concentration of aqueous CMC solutions generate larger heat transfer coefficients. Finally, a comparison with the experimental and numerical results available in the literature for Newtonian fluids shows clearly that the present analysis is reasonably accurate. Received on 29 March 2001 / Published online: 29 November 2001     

Heat transfer promotion with a cylinder array located near the wall

Heat transfer from a flat plate has been investigated when a cylinder array is located near the wall. Each cylinder in the cylinder array was positioned normal to the flow direction and parallel to the flat plate surface. Measurements of the heat transfer coefficient and the optimum value for the cylinder pitch and spacing between the cylinders and the flat plate surface were obtained. A comparison of the heat transfer mechanism in this flow system with that obtained previously for the case when a single cylinder is inserted in the boundary layer was made.     

Exact solution of conductive heat transfer in cylindrical composite laminate

This paper presents an exact solution for steady-state conduction heat transfer in cylindrical composite laminates. This laminate is cylindrical shape and in each lamina, fibers have been wound around the cylinder. In this article heat transfer in composite laminates is being investigated, by using separation of variables method and an analytical relation for temperature distribution in these laminates has been obtained under specific boundary conditions. Also Fourier coefficients in each layer obtain by solving set of equations that related to thermal boundary layer conditions at inside and outside of the cylinder also thermal continuity and heat flux continuity between each layer is considered. In this research LU factorization method has been used to solve the set of equations.     

Friction and heat transfer with simultaneous convection on a permeable surface

The velocity and heat transfer fields near a vertical permeable surface with simultaneous convection are investigated. A solution is found for the boundary layer equations with known laws of surface temperature and flow velocity change. The transformed boundary layer equations contain the parameter G/R², which determines the effect of free convection on friction and heat transfer for constrained motion. Calculations of friction and heat transfer as functions of draft (suction) with simultaneous convection are presented.Translated from Zhurnal Prikladnoi Mekhaniki i Tekhnicheskoi Fiziki, No. 2, pp. 96–100, March–April, 1973.     

Effects of prescribed heat flux and transpiration on MHD axisymmetric flow impinging on stretching cylinder

A numerical treatment for axisymmetric flow and heat transfer due to a stretching cylinder under the influence of a uniform magnetic field and prescribed surface heat flux is presented. Numerical results are obtained for dimensionless velocity, temperature, skin friction coefficient and Nusselt number for several values of the suction/injection, magnetic and curvature parameters as well as the Prandtl number. The present study reveals that the controlling parameters have strong effects on the physical quantities of interest. It is seen that the magnetic field enhances the dimensionless temperature inside the thermal boundary layer, whereas it reduces the dimensionless velocity inside the hydrodynamic boundary layer. Heat transfer rate reduces, while the skin friction coefficient increases with magnetic field.     

Flow of variable thermal conductivity fluid due to inclined stretching cylinder with viscous dissipation and thermal radiation

The aim of the present study is to investigate the flow of the Casson fluid by an inclined stretching cylinder. A heat transfer analysis is carried out in the presence of thermal radiation and viscous dissipation effects. The temperature dependent thermal conductivity of the Casson fluid is considered. The relevant equations are first simplified under usual boundary layer assumptions, and then transformed into ordinary differential equations by suitable transformations. The transformed ordinary differential equations are computed for the series solutions of velocity and temperature. A convergence analysis is shown explicitly. Velocity and temperature fields are discussed for different physical parameters by graphs and numerical values. It is found that the velocity decreases with the increase in the angle of inclination while increases with the increase in the mixed convection parameter. The enhancement in the thermal conductivity and radiation effects corresponds to a higher fluid temperature. It is also found that heat transfer is more pronounced in a cylinder when it is compared with a flat plate. The thermal boundary layer thickness increases with the increase in the Eckert number. The radiation and variable thermal conductivity decreases the heat transfer rate at the surface.     

Mixed convection boundary layer flow of a viscoelastic fluid over a horizontal circular cylinder

The steady mixed convection boundary layer flow of a viscoelastic fluid over a horizontal circular cylinder in a stream flowing vertically upwards is numerically studied for both cases of heated and cooled cylinders. The governing partial differential equations are transformed into dimensionless forms using an appropriate transformation and then solved numerically using the Keller-box method. The comparison between the solutions obtained and those for a Newtonian fluid is found to be very good. Effects of the mixed convection and elasticity parameters on the skin friction and heat transfer coefficients for a fluid having the Prandtl number equal to one are also discussed. It is found that for some values of the viscoelastic parameter and some negative values of the mixed convection parameter (opposing flow) the boundary layer separates from the cylinder. Heating the cylinder delays separation and can, if the cylinder is warm enough, suppress the separation completely. Similar to the case of a Newtonian fluid, cooling the cylinder brings the separation point nearer to the lower stagnation point. However, for a sufficiently cold cylinder there will not be a boundary layer.     

Heat transfer enhancement in a turbulent natural convection boundary layer along a vertical flat plate

An experimental study on heat transfer enhancement for a turbulent natural convection boundary layer in air along a vertical flat plate has been performed by inserting a long flat plate in the spanwise direction (simple heat transfer promoter) and short flat plates aligned in the spanwise direction (split heat transfer promoter) with clearances into the near-wall region of the boundary layer. For a simple heat transfer promoter, the heat transfer coefficients increase by a peak value of approximately 37% in the downstream region of the promoter compared with those in the usual turbulent natural convection boundary layer. It is found from flow visualization and simultaneous measurements of the flow and thermal fields with hot- and cold-wires that such increase of heat transfer coefficients is mainly caused by the deflection of flows toward the outer region of the boundary layer and the invasion of low-temperature fluids from the outer region to the near-wall region with large-scale vortex motions riding out the promoter. However, heat transfer coefficients for a split heat transfer promoter exhibit an increase in peak value of approximately 60% in the downstream region of the promoter. Flow visualization and PIV measurements show that such remarkable heat transfer enhancement is attributed to longitudinal vortices generated by flows passing through the clearances of the promoter in addition to large-scale vortex motions riding out the promoter. Consequently, it is concluded that heat transfer enhancement of the turbulent natural convection boundary layer can be substantially achieved in a wide area of the turbulent natural convection boundary layer by employing multiple column split heat transfer promoters. It may be expected that the heat transfer enhancement in excess of approximately 40% can be accomplished by inserting such promoters.     

A transient natural convection of micropolar fluids over a vertical cylinder

A transient free convective boundary layer flow of micropolar fluids past a semi-infinite cylinder is analysed in the present study. The transformed dimensionless governing equations for the flow, microrotation and heat transfer are solved by using the implicit scheme. For the validation of the current numerical method heat transfer results for a Newtonian fluid case where the vortex viscosity is zero are compared with those available in the existing literature, and an excellent agreement is obtained. The obtained results concerning velocity, microrotation and temperature across the boundary layer are illustrated graphically for different values of various parameters and the dependence of the flow and temperature fields on these parameters is discussed. An increase in the vortex viscosity tends to increase the magnitude of microrotation and thus decreases the peak velocity of fluid flow. An increase in the vortex viscosity in micropolar fluids is shown to decrease the heat transfer rate.     

Effect of viscous dissipation on the mixed convection heat transfer from an exponentially stretching surface

The mixed convection flow and heat transfer from an exponentially stretching vertical surface in a quiescent fluid is analyzed using similarity solution technique. Wall temperature and stretching velocity are assumed to have specific exponential function forms. The influence of buoyancy along with viscous dissipation on the convective transport in the boundary layer region is analyzed in both aiding and opposing flow situations. The flow is governed by the mixed convection parameter Gr/Re². The velocity and temperature inside the boundary layer are observed to be influenced by the parameters like Prandtl number Pr, Gebhart number Gb. Significant changes are observed in non-dimensional skin friction and heat transfer coefficients due to viscous dissipation in the medium. The flow and temperature distributions inside the boundary layer are analyzed and the results for non-dimensional skin friction and heat transfer coefficients are discussed through computer generated plots.