Thermal decomposition of Mo(CO)6 on thin Al2O3 film: A combinatorial investigation by XPS and UPS

A thin and homogeneous alumina film was prepared by deposition and oxidation of aluminum on a refractory Re(0 0 0 1) substrate under ultrahigh vacuum conditions. X-ray photoelectron spectroscopy (XPS), ultraviolet photoelectron spectroscopy (UPS) and high-resolution electron-energy-loss spectroscopy (HREELS) demonstrate that the oxide film is long-range ordered, essentially stoichiometric and free from surface hydroxyl groups. The chemisorption and thermal decomposition of Mo(CO)₆ on the Al₂O₃ film were investigated by means of XPS and UPS. Mo(CO)₆ adsorbs molecularly on the oxide film at 100 K; however, thermal decomposition of the adsorbate occurs upon annealing at high temperatures. Consequently the metallic molybdenum clusters are deposited on the thin alumina film via complete decarbonylation of Mo(CO)₆.     

Preparation and characterization of amine-functionalized SiO2/TiO2 films for formaldehyde degradation

This paper investigated the gaseous formaldehyde degradation by the amine-functionalized SiO₂/TiO₂ photocatalytic films for improving indoor air quality. The films were synthesized via the co-condensation reaction of methyltrimethoxysilane (MTMOS) and 3-aminopropyltrimethoxysilane (APTMS). The physicochemical properties of prepared photocatalysts were characterized with N₂ adsorption/desorption isotherms measurement, X-ray diffraction (XRD) and Fourier Transform Infrared spectroscopy (FT/IR). The effect of amine-functional groups and the ratio of MTMOS/APTMS precursors on the formaldehyde adsorption and photocatalytic degradation were investigated. The results showed that the formaldehyde adsorption and photocatalytic degradation of the APTMS-functionalized SiO₂/TiO₂ film was higher than that of SiO₂/TiO₂ film due to the surface adsorption on amine sites and the relatively high of the specific surface area of the APTMS-functionalized SiO₂/TiO₂ film (15 times higher than SiO₂/TiO₂). The enhancement of the formaldehyde degradation of the film can be attributed to the synergetic effect of adsorption and subsequent photocatalytic decomposition. The repeatability of photocatalytic film was also tested and the degradation efficiency was 91.0% of initial efficiency after seven cycles.     

三甲基镓在Pd(111)表面吸附解离及表面预吸附H和O的影响

利用X-射线光电子能谱（XPS）和程序升温脱附谱（TPD）研究了三甲基镓在Pd（111）表面的吸附和解离行为,并考察了表面预吸附H和O的影响。结果表明,在吸附温度为140 K时,三甲基镓在Pd（111）上主要为解离吸附,此时表面物种为Ga（CH₃）_x （x=1,2,3）和CH_x物种。加热将导致Ga的甲基化合物中的Ga-C键发生分步断裂,在不同温度下产生CH₄和H₂从表面脱附。同时,XPS结果证实了在275~325 K的温度区间内存在Ga甲基化合物的分子脱附。退火至更高温度,表面只观察到积碳和金属Ga物种,这二者随着温度的继续升高逐渐向体相扩散。在Pd（111）表面预吸附O和H对上述吸附和解离行为存在显著的影响。当表面预吸附H时,脱附产物CH₄和H₂的脱附主要位于315 K,可归属为一甲基镓的解离脱附。当表面预吸附O时,只在258 K观察到CH₄和H₂的脱附峰,可能来自于Pd-O-Ga（CH₃）₂吸附结构的解离.     

Pd修饰Cu电极的电化学CO2还原

利用微分电化学质谱和电化学原位衰减全反射红外光谱技术探究了Cu和CuPd催化剂上CO₂和CO的电化学还原行为. 红外光谱观察到了生成甲醇、甲烷与乙烯的CH_x中间物种. 在CuPd电极CO₂还原过程中，红外光谱的CO吸附峰起始电位比Cu正移大约300 mV，说明CuPd能够有效促进CO₂还原；CO饱和溶液中，Cu和CuPd电极CO起始吸附电位基本相同；两电极上CO谱带出现的电位与CO₃^2-的谱带降低的电位基本相同，说明CO的吸附需要CO₃^2-的脱附. 利用电化学在线质谱发现在CuPd电极上CO还原产生CH₄和CH₃OH的起始电位比Cu电极正移约200 mV. 推测催化活性的提升可能是由于Pd的引入改变了Cu的d能带，且Pd吸附更多的H，从而促进CO₂还原，使CO能够与H结合并被深度还原.     

CO oxidation of bare and TiO2-coated NiO-Ni(OH)2 nanoparticles

CO oxidation reactivity of bare and TiO₂-coated nanoparticles consisting of both NiO and Ni(OH)₂ surfaces was studied. For the deposition of TiO₂, atomic layer deposition was used, and formation of three-dimensional domains of TiO₂ on NiO-Ni(OH)₂ could be identified. Based on the data of X-ray Photoelectron Spectroscopy, we suggest that upon TiO₂ deposition only Ni(OH)₂ was remained on the surface, whereas NiO surface disappeared. Both CO adsorption and CO oxidation took place on NiO-Ni(OH)₂ surfaces under our experimental conditions. CO adsorption was almost completely suppressed after TiO₂ deposition, whereas CO oxidation activity was maintained to large extent. It is proposed that bare NiO cannot be active for CO oxidation, and can only uptake CO under our experimental condition, whereas hydroxylated surface of NiO can be active for CO oxidation.     

Role of Cl ions in photooxidation of propylene on TiO2 surface

The effect of Cl⁻ ions on photooxidation of propylene on TiO₂ semiconductor was investigated. Cl⁻/TiO₂ catalysts were prepared by annealing Degussa P25 TiO₂ in the gas flow of N₂ and Cl₂ under 100-400 °C. The photocatalytic oxidation of propylene was carried out in a continuous flow system, with the chromatograph to analyze the products on line. The experimental results showed that the activity of Cl⁻/TiO₂ catalysts increased as heat-treated temperature decreased. The activity of the sample heat-treated at 100 °C was about two times higher than that of pure TiO₂. Moreover, as to TiO₂, the main product of the propylene photocatalytic oxidation was CO₂, but with Cl⁻/TiO₂ catalysts, not only CO₂ but also trace CO was determined. The adsorbed species on TiO₂ surface before and after reaction were analyzed by X-ray photoelectron spectroscopy (XPS) and thermogravimetric/differential thermal analyses (TG-DTA) coupled to a mass spectrometer (MS). XPS analysis showed that there was Cl⁻ absorbed on the Cl⁻/TiO₂ surface, and the absorption amount of Cl⁻ decreased after the photooxidation reaction of propylene. TG-DTA-MS analysis confirmed chlorine absorbed on the surface of TiO₂ in the form of Cl⁻ ion. These results illuminated that absorbed Cl⁻ on the surface of TiO₂ formed a weak physical absorption on TiO₂ at low temperature, and subsequently participated in the photooxidation of propylene, finally removed from TiO₂ surface.     

Adsorption CO2 on the perfect and oxygen vacancy defect surfaces of anatase TiO2 and its photocatalytic mechanism of conversion to CO

The adsorption energies for physisorption and the most stable chemisorption of CO₂ on the neutral charge of perfect anatase [TiO₂] (0 0 1) are −9.03 and −24.66 kcal/mol on the spin-unpolarized and −12.98 and −26.19 kcal/mol on the spin-polarized surface. The small activation barriers of 1.67 kcal/mol on the spin-unpolarized surface and of 6.66 kcal/mol on the spin-unpolarized surface were obtained. The adsorption mechanism of CO₂ on the oxygen vacancy defect [TiO₂ + V_O] surface of anatase TiO₂ using density functional theory calculations was investigated. The energetically preferred conversion of CO₂ to CO was found either on the spin-unpolarized or spin-polarized surfaces of oxygen vacancy defect surface [TiO₂ + V_O] as photocatalyst.     

Theoretical study of CO adsorption on the illuminated TiO2 (0 0 1) surface

A quantum modeling of the CO adsorption on illuminated anatase TiO₂ (0 0 1) is presented. The calculated adsorption energy and geometries of illuminated case are compared with the ground state case. The calculations were achieved by using DFT formalism and the BH and HLYP. Upon photoexcitation, an electron-hole pair is generated. Comparing of natural population in the ground state and the exited state, shows that an electron is trapped in a Ti⁴⁺ ion and a hole is localized in an oxygen ion. The photoelectron helps generation of a CO₂ molecule on the TiO₂ surface. As shown by optimization of these systems, the CO molecule adsorbed vertically on the TiO₂ (0 0 1) surface in the ground state case while the CO molecule made an angle of 134.3° to this surface at the excited state case. Based on the here used model the obtained adsorption energy was 0.36 eV which is in excellent agreement with the reported experimental value. In the present work the C-O stretch IR frequencies are calculated which are 1366.53 and 1423.16 cm⁻¹. These results are in good agreement with the earlier reported works for the surface carbonaceous compounds, and oxygenated carbon species.     

Adsorption of CO, CO2 and NO molecules on a BaTiO3 (0 0 1) surface

Since the development of Scanning Tunnelling Microscopy (STM) technique, considerable attention has been devoted to various molecules adsorbed on various surfaces. Also, a new concept emerged with molecules on surfaces considered as nano machines by themselves. In this context, a thorough knowledge of surfaces and adsorbed molecules at an atomic scale are thus particularly invaluable. The present work describes the first Density Functional Theory (DFT) study of adsorption of CO, CO₂ and NO molecules on a BaTiO₃ surface following a first preliminary calculation of O and O₂ adsorption on the same surface. In the previously considered work, we found that a (0 0 1) surface with BaO termination is more stable than the one with TiO₂-termination. Consequently, we extended our study to CO, CO₂ and NO molecules adsorbed on a (0 0 1) surface with BaO termination. The present calculation was performed on a (1 × 1) cell with one monolayer of adsorbed molecules. Especially, a series of cases implying CO molecules adsorbed in various geometrical configurations has been examined. The corresponding adsorption energy varies in the range of −0.17 to −0.10 eV. The adsorption energy of a CO₂ molecule directly located above an O surface atom (called O_s) is of the order of −0.18 eV. The O-C distance length is then 1.24 Å and the O-C-O and O-C-O_s angles are 134.0° and 113.0°, respectively. For NO adsorption, the most important induced structural changes are the followings: (i) the N-O bond is broken when a NO molecule is absorbed on a Ba-O_s bridge site. In that case, N and O atoms are located above an O and a Ba surface atom, respectively, whereas the O-Ba-O_s and N-O_s-Ba angles are 106.5° and 63.0°, respectively. The N-O distance is as large as 2.58 Å and the adsorption energy is as much as −2.28 eV. (ii) In the second stable position, the NO molecule has its N atom adsorbed above an O_s atom, the N-O axis being tilted toward the Ba atom. The N-O_s-Ba angle is then 41.1° while the adsorption energy is only −0.10 eV. At last, the local densities of states around C, O as well as N atoms of the considered adsorbed molecules have also been discussed.     

Au/TiO2/Ru(0 0 0 1) model catalysts and their interaction with CO

Au/TiO₂/Ru(0 0 0 1) model catalysts and their interaction with CO were investigated by scanning tunneling microscopy and different surface spectroscopies. Thin titanium oxide films were prepared by Ti deposition on Ru(0 0 0 1) in an O₂ atmosphere and subsequent annealing in O₂. By optimizing the conditions for deposition and post-treatment, smooth films were obtained either as fully oxidized TiO₂ or as partly reduced TiO_x, depending on the preparation conditions. CO adsorbed molecularly on both oxidized and reduced TiO₂, with slightly stronger bonding on the reduced films. Model catalyst surfaces were prepared by depositing submonolayer quantities of Au on the films and characterized by X-ray photoelectron spectroscopy and scanning tunneling microscopy. From X-ray photoelectron spectroscopy, a weak interaction between the Au and the TiO₂ substrate was found. At 100 K CO adsorption occurred on both the TiO₂ film and on the Au nanoparticles. CO desorbed from the Au particles with activation energies between 53 and 65 kJ/mol, depending on the Au coverage. If the Au deposit was annealed to 770 K prior to CO exposure, the CO adsorption energy decreased significantly. STM measurements revealed that the Au particles grow upon annealing, but are not encapsulated by TiO_x suboxides. The higher CO adsorption energy observed for smaller Au coverages and before annealing is attributed to a significantly stronger interaction of CO with mono- and bilayer Au islands, while for higher particles, the adsorption energy becomes more bulk-like. The implications of these effects on the known particle size effects in CO oxidation over supported Au/TiO₂ catalysts are discussed.     

LEED and thermal desorption studies of small molecules (H2, O2, CO,CO2, NO,C2H4, C2H2 and C) chemisorbed on the stepped rhodium (755) and (331) surfaces

The chemisorption of H₂, O₂, CO, CO₂, NO, C₂H₂, C₂H₄ and C has been studied on the clean stepped Rh(755) and (331) surfaces. Low energy electron diffraction (LEED), Auger electron spectroscopy (AES) and thermal desorption spectroscopy (TDS) were used to determine the size and orientation of the unit cells, desorption temperatures and decomposition characteristics for each adsorbate. All of the molecules studied readily chemisorbed on both stepped surfaces and several ordered surface structures were observed. The LEED patterns seen on the (755) surface were due to the formation of surface structures on the (111) terraces, while on the (331) surface the step periodicity played an important role in the determination of the unit cells of the observed structures. When heated in O₂ or C₂H₄ the (331) surface was more stable than the (755) surface which readily formed (111) and (100) facets. In the CO and CO₂ TDS spectra a peak due to dissociated CO was observed on both surfaces. NO adsorption was dissociative at low exposures and associative at high exposures. C₂H₄ and C₂H₂ had similar adsorption and desorption properties and it is likely that the same adsorbed species was formed by both molecules.     

Kinetic aspect of CO2 reforming of CH4 on Ni(1 1 1): A density functional theory calculation

Reaction pathways of CO₂ reforming of CH₄ on Ni(1 1 1) were investigated by using density functional theory calculation. The computed kinetic parameters agree with the available experimental data, and a new and simplified mechanism was proposed on the basis of computed energy barriers. The first step is CO₂ dissociation into surface CO and O (CO₂ → CO + O) and CH₄ sequentially dissociation into surface CH and H (CH₄ → CH₃ → CH₂ → CH). The second step is CH oxygenation into CHO (CH + O → CHO), which is more favored than its dissociation into C and hydrogen (CH → C + H). The third step is the dissociation of CHO into surface CO and H (CHO → CO + H). Finally, H₂ and CO desorb from Ni(1 1 1) and form free H₂ and CO. The rate-determining step is the CH₄ dissociative adsorption, and the key intermediate is surface adsorbed CHO. Parameters, which might modify the proposed mechanism, have been analyzed. In addition, the formation, deposition and elimination of surface carbon have been discussed accordingly.     

CO和O2分子与TiO2(110)表面负载Pt单原子的相互作用

Pt单原子在低温CO氧化反应中具有很高的催化活性. 利用扫描隧道显微术与密度泛函理论，研究了Pt单原子在还原性TiO₂(110)表面的吸附行为及其与CO和O₂分子的相互作用. 研究发现在80 K低温下，TiO₂表面的氧空位缺陷是Pt单原子的最优吸附位. 将CO和O₂分子分别通入Pt单原子吸附后的TiO₂表面，研究相应的吸附构型. 实验表明在低覆盖度下，单个Pt原子会俘获一个CO分子，CO分子同时与表面次近邻的五配位Ti原子(Ti_5c)成键，进而形成非对称的Pt-CO 复合物构型. 将样品从80 K升温到100 K后，TiO₂表面的CO分子会迁移到Pt-CO处形成Pt-(CO)₂的复合结构. 对于O₂分子，单个Pt原子同样会吸附一个O₂分子，O₂分子也会与最近邻或次近邻的Ti_5c原子成键形成两种Pt-O₂构型. 这些结果在单分子尺度上揭示了CO和O₂与Pt单原子的相互作用，呈现了CO与O₂反应中的初始状态.     

Lattice site dependent cathodoluminescence behavior and surface chemical changes in a Sr5(PO4)3F host

Eu activated Sr₅(PO₄)₃F phosphor powders have been subjected to the electron bombardment at 2 keV (10 μA) at an oxygen pressure of 1×10⁻⁶ Torr. The synthesized Sr₅(PO₄)₃F phosphor was identical to the hexagonal apatite structure, with the Sr present at two different sites C_s (S1) and C₃ (S2) in the Sr₅(PO₄)₃F host, as inferred from the crystallographic study. Cathodoluminescence (CL) and Auger electron spectroscopy of the phosphor excited by the same electron beam were used to monitor changes in the surface state during prolonged electron bombardment. A direct correlation between the surface reactions and the degradation of the CL brightness was observed. Both C and F were depleted from the surface during electron bombardment. The postulated mechanism for the electron stimulated chemical reactions on the phosphor surface is electron beam dissociation of molecular species to atomic species, which subsequently react with C to form volatile compounds CO₂, CH₄, etc. and with Sr₅(PO₄)₃F to form a non luminescence layer of metal oxides of Sr and P.     

亚纳米厚的氧化铝包裹层可以显著提高负载型金纳米颗粒催化剂的热稳定性

负载型金纳米颗粒催化剂在许多催化反应中展现出非常好的催化活性,但是金纳米颗粒在高温等反应条件下容易烧结团聚,极大地限制了金催化剂的应用。利用原子层沉积技术在Au/TiO₂催化剂表面分别精确沉积了一层超薄的二氧化钛和氧化铝包裹层,并对比研究了包裹层对金纳米颗粒的热稳定性影响。原位红外漫反射CO吸附和x-射线光电子能谱数据证实了氧化物包裹层的存在。发现亚纳米厚的氧化铝包裹层能够在600 C完全避免金纳米颗粒的团聚;相反,二氧化钛包裹层对金纳米颗粒稳定性的提高没有明显效果。通过CO氧化探针反应的活性测试,发现随着煅烧温度的升高氧化铝包裹的Au/TiO₂ 催化剂的活性逐渐提高,表明高温处理可以促进被包裹金原子的暴露并表现出催化活性。提供了提高金纳米颗粒稳定性的有效方法,为拓展金催化剂在条件苛刻的反应中的应用奠定了技术基础.     

Synthesis and photocatalytic oxidation of different organic dyes by using Mn2O3/TiO2 solid solution and visible light

Mn₂O₃/TiO₂ solid solution was prepared from two different oxides, manganese oxide (from KMnO₄ and ethanol) and TiO₂, these samples were characterized by BET, XRD, EDAX, SEM, FT-IR, ESR, XPS and UV–vis absorption spectroscopy. Photocatalytic activities of Mn₂O₃/TiO₂ powder was investigated by photooxidation of different dyes like Rhodamine B, thymol blue, methyl orange and Bromocresol green under visible light (300-W Xe lamp; λ > 420 nm). The results show that the alloy of TiO₂ with 1 mol% of Mn₂O₃ (MNT1) exhibit photocatalytic activity 3–5 times higher than that of P25 TiO₂ for oxidation of various dyes (RB, TB, MO and BG). The average particle size and crystallite size of MNT1 were found to be 100 nm and 12 nm measured from SEM and XRD, respectively. The EPR spectra of the Mn₂O₃/TiO₂ samples is a sharp five-line Mn(III) component centered on g_eff = 1.99.     

Deposition and characterization of binary Al2O3/SiO2 coating layers on the surfaces of rutile TiO2 and the pigmentary properties

Binary Al₂O₃/SiO₂-coated rutile TiO₂ composites were prepared by a liquid-phase deposition method starting from Na₂SiO₃·9H₂O and NaAlO₂. The chemical structure and morphology of binary Al₂O₃/SiO₂ coating layers were investigated by Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy, TG-DSC, Zeta potential, powder X-ray diffraction, and transmission electron microscopy techniques. Binary Al₂O₃/SiO₂ coating layers both in amorphous phase were formed at TiO₂ surfaces. The silica coating layers were anchored at TiO₂ surfaces via Si-O-Ti bonds and the alumina coating layers were probably anchored at the SiO₂-coated TiO₂ surfaces via Al-O-Si bonds. The formation of continuous and dense binary Al₂O₃/SiO₂ coating layers depended on the pH value of reaction solution and the alumina loading. The binary Al₂O₃/SiO₂-coated TiO₂ composites had a high dispersibility in water. The whiteness and brightness of the binary Al₂O₃/SiO₂-coated TiO₂ composites were higher than those of the naked rutile TiO₂ and the SiO₂-coated TiO₂ samples. The relative light scattering index was found to depend on the composition of coating layers.     

Adsorption of CO2 on PbO at ambient temperature

The adsorption of CO₂ on metal oxides at ambient temperature received less study largely due to the small adsorption amount. However, the adsorption is of interest in refreshing the atmosphere of isolated spaces. It was shown in the present work that P_bO was sensitive to low concentration CO₂ in the presence of water. An XPS examination indicated that P_bO changed to P_bCO₃ after the adsorption of CO₂; therefore, the adsorption is chemical in nature. In order to enlarge the CO₂ capacity, P_bO was dispersed on the surface of a silica gel with large surface area (710 m²/g). Both CO₂ capacity and adsorption rate indicated that the optimal dispersion manner of P_bO is the mono-molecular layer surface coverage. Breakthrough experiments showed that the prepared adsorbent could effectively capture low-concentration CO₂ at ambient temperature and pressure yielding a CO₂ capacity of 59.1 mg g⁻¹. The saturated adsorbent was regenerated on heating at 380 °C and the CO₂ capability was recovered.     

CO2 dissociation on Ni(2 1 1)

The direct and H-mediated dissociation of CO₂ on Ni(2 1 1) were investigated at the level of density functional theory. Although formate (HCOO) formation via CO₂ hydrogenation was widely reported for CO₂ adsorption on metal surfaces, it is found that on Ni(2 1 1) HCOO dissociation into CHO and O is much difficult, while direct dissociation of adsorbed CO₂ into CO and O is more favorable. It is also found that the degree of electron transfer from surface to adsorbed CO₂ correlates with the elongation of C-O bond lengths and the reduction of the CO₂ dissociation barrier.     

Auger electron spectroscopic study of CO2 adsorption on Zircaloy-4 surfaces

We investigate the adsorption of CO₂ onto Zircaloy-4 (Zry-4) surfaces at 150, 300 and 600 K using Auger electron spectroscopy (AES). Following CO₂ adsorption at 150 K the graphitic form of carbon is detected, whereas upon chemisorption at 300 and 600 K we detect the carbidic phase. As the adsorption temperature is increased, the carbon Auger signal increases, whereas the oxygen signal decreases. Adsorption at all three temperatures results in a shift of the Zr Auger features, indicating surface oxidation. The effect of adsorbed CO₂ on the Zr(MVV) and Zr(MNV) transitions depends on adsorption temperature and is less pronounced at higher temperatures. On the other hand, changes in the Zr(MNN) feature are similar for all three adsorption temperatures. The changes in the Zr Auger peak shapes and positions are attributed to oxygen from dissociated CO₂, with the differences observed at various temperatures indicative of the diffusion of oxygen into the subsurface region.