The effects of burner stabilization on Fenimore NO formation in low-pressure, fuel-rich premixed CH4/O2/N2 flames

We investigate the effects of varying the degree of burner stabilization on Fenimore NO formation in fuel-rich low-pressure flat CH₄/O₂/N₂ flames. Towards this end, axial profiles of flame temperature and OH, NO and CH mole fractions are measured using laser-induced fluorescence (LIF). The experiments are performed at equivalence ratios between 1.3 and 1.5. The flame temperature is seen to decrease by 200-300 K, with a concomitant decrease in OH mole fraction, upon reducing the total flow rate from 5 to 3 L/min, thus increasing stabilization. At equivalence ratios between 1.3 and 1.5, this decrease in flow rate lowers the maximum CH mole fraction by a factor of 2, and the NO mole fraction by ∼40% in all flames studied. Integrating the reaction rate for CH + N₂ to estimate Fenimore NO formation, using the rate coefficient in GRI-Mech 3.0, and the measured temperatures and CH profiles show very good agreement with the measured NO mole fraction for ? = 1.3 and 1.4, supporting the current choice for this rate. This agreement also shows that the increase in residence time caused by increased stabilization is an important factor in the ultimate impact of the changes in CH mole fraction on NO formation. The results at ? = 1.5 suggest that substantial quantities of fixed nitrogen species, e.g., HCN, are only slowly oxidized in the post-flame zone under these conditions, leading to a significant discrepancy between the measured NO mole fraction and that obtained by integrating over the CH profile. Detailed calculations using GRI-Mech 3.0 predict the experimental results at ? = 1.3 nearly quantitatively, but show increasing differences with the measurements for both CH and NO profiles with increasing equivalence ratio.     

Epitaxial MoOx nanostructures on TiO2(1 1 0) obtained using thermal decomposition of Mo(CO)6

Stoichiometric and highly-defective TiO₂(1 1 0) surfaces (called as yellow and blue, respectively) were exposed to Mo(CO)₆ vapours in UHV and in a reactive O₂ atmosphere. In the case of yellow-TiO₂, an O₂ reactive atmosphere was necessary to obtain the Mo(CO)₆ decomposition at 450 °C with deposition of MoO_x nanostructures where, according to core level photoemission data, the Mo⁺⁴ state is predominant. In the case of blue-TiO₂ it was possible to obtain Mo deposition both in UHV and in an O₂ atmosphere. A high dose of Mo(CO)₆ in UHV on blue-TiO₂ allowed the deposition of a thick metallic Mo layer. An air treatment of this sample at 580 °C led to the elimination of Mo as MoO₃ and to the formation of a transformed layer of stoichiometry of Ti_(1−x)Mo_xO₂ (where x is close to 0.1) which, according to photoelectron diffraction data, can be described as a substitutional near-surface alloy, where Mo⁺⁴ ions are embedded into the titania lattice. This embedding procedure results in a stabilization of the Mo⁺⁴ ions, which are capable to survive to air exposure for a rather long period of time. After exposure of the blue-TiO₂(1 1 0) substrate to Mo(CO)₆ vapours at 450 °C in an O₂ atmosphere it was possible to obtain a MoO₂ epitaxial ultrathin layer, whose photoelectron diffraction data demonstrate that is pseudomorphic to the substrate.     

Chemical quenching of positronium in Fe2O3/Al2O3 catalysts

Fe₂O₃/Al₂O₃ catalysts were prepared by solid state reaction method using α-Fe₂O₃ and γ-Al₂O₃ nano powders. The microstructure and surface properties of the catalyst were studied using positron lifetime and coincidence Doppler broadening annihilation radiation measurements. The positron lifetime spectrum shows four components. The two long lifetimes τ₃ and τ₄ are attributed to positronium annihilation in two types of pores distributed inside Al₂O₃ grain and between the grains, respectively. With increasing Fe₂O₃ content from 3 wt% to 40 wt%, the lifetime τ₃ keeps nearly unchanged, while the longest lifetime τ₄ shows decrease from 96 ns to 64 ns. Its intensity decreases drastically from 24% to less than 8%. The Doppler broadening S parameter shows also a continuous decrease. Further analysis of the Doppler broadening spectra reveals a decrease in the p-Ps intensity with increasing Fe₂O₃ content, which rules out the possibility of spin-conversion of positronium. Therefore the decrease of τ₄ is most probably due to the chemical quenching reaction of positronium with Fe ions on the surface of the large pores.     

Room-temperature ferromagnetism in Sn1−xMnxO2 nanocrystalline thin films prepared by ultrasonic spray pyrolysis

Sn_1−xMn_xO₂ (x=0.01-0.05) thin films were synthesized on quartz substrate using an inexpensive ultrasonic spray pyrolysis technique. The influence of doping concentration and substrate temperature on structural and magnetic properties of Sn_1−xMn_xO₂ thin films was systematically investigated. X-ray diffraction (XRD) studies of these films reflect that the Mn³⁺ ions have substituted Sn⁴⁺ ions without changing the tetragonal rutile structure of pure SnO₂. A linear increase in c-axis lattice constant has been observed with corresponding increase in Mn concentration. No impurity phase was detected in XRD patterns even after doping 5 at% of Mn. A systematic change in magnetic behavior from ferromagnetic to paramagnetic was observed with increase in substrate temperature from 500 to 700 °C for Sn_1−xMn_xO₂ (x=0.01) films. Magnetic studies reveal room-temperature ferromagnetism (RTFM) with 3.61×10⁻⁴ emu saturation magnetization and 92 Oe coercivity in case of Sn_1−xMn_xO₂ (x=0.01) films deposited at 500 °C. However, paramagnetic behavior was observed for the films deposited at a higher substrate temperature of 700 °C. The presence of room-temperature ferromagnetism in these films was observed to have an intrinsic origin and could be obtained by controlling the substrate temperature and Mn doping concentration.     

High-throughput characterization of BixY3−xFe5O12 combinatorial thin films by magneto-optical imaging technique

Bi_xY_3−xFe₅O₁₂ thin films have been grown on GGG (Gd₃Ga₅O₁₂) (1 1 1) substrates by the combinatorial composition-spread techniques under substrate temperature (T_sub) ranging from 410 to 700 °C and O₂ pressure of 200 mTorr. In order to study the effect of substrates on the deposition of Bi_xY_3−xFe₅O₁₂ thin films, garnet substrates annealed at 1300 °C for 3 h were also used. Magneto-optical properties were characterized by our home-designed magneto-optical imaging system. From the maps of Faraday rotation angle θ_F, it was evident that the Faraday effect appears only when T_sub = 430-630 °C. θ_F reaches to the maximum value (∼6°/μm, λ = 632 nm) at 500 °C, and is proportional to the Bi contents. XRD and EPMA analyses showed that Bi ions are easier to substitute for Y sites and better crystallinity is obtained for annealed substrates than for commercial ones.     

Effects of CeO2-ZrO2 present in Pd/Al2O3 catalysts on the redox behavior of PdOx and their combustion activity

The ceria-zirconium-modified alumina-supported palladium catalysts are prepared using impregnation method with H₂PdCl₄ as Pd source, hydrazine hydrate as reducing agent. The physicochemical properties of these catalysts are characterized by BET surface area (BET), X-ray powder diffraction (XRD), transmission electron microscopy (TEM), temperature programmed reduction (H₂-TPR) and temperature programmed oxidation (O₂-TPO) techniques, and their catalytic activities for the combustion of methane are examined. The results show that the palladium mainly exist in a highly dispersed PdO species on Ce-Zr-rich grains as well as Al₂O₃-rich grains surfaces, and a stable PdO species due to the strong interaction between PdO and CeO₂-ZrO₂ on the Ce-Zr/Al₂O₃ surfaces. The catalytic activity is strongly related to the redox behavior of PdO species highly dispersed on Ce-Zr-rich grains and Al₂O₃-rich grains surfaces, and the higher the reducibility of the PdO species, the higher the catalytic activity. The presence of Ce-Zr in Pd/Al₂O₃ catalyst would inhibit the site growth of PdO_x particles and decomposition of PdO to Pd⁰, and the reoxidation property of Pd⁰ to PdO_x is significantly improved, which obviously increases thermal stability and catalytic activity of Pd/Ce-Zr/Al₂O₃ catalyst for the methane combustion.     

Effect of TiO2/Al2O3 film coated diamond abrasive particles by sol-gel technique

The diamond abrasive particles were coated with the TiO₂/Al₂O₃ film by the sol-gel technique. Compared with the uncoated diamonds, the TiO₂/Al₂O₃ film was excellent material for the protection of the diamonds. The results showed that the incipient oxidation temperature of the TiO₂/Al₂O₃ film coated diamonds in air atmosphere was 775 °C, which was higher 175 °C than that of the uncoated diamonds. And the coated diamonds also had better the diamond's single particle compressive strength and the impact toughness than that of uncoated diamonds after sintering at 750 °C. For the vitrified bond grinding wheels, replacing the uncoated diamonds with the TiO₂/Al₂O₃ film coated diamonds, the volume expansion of the grinding wheels decreased from 6.2% to 3.4%, the porosity decreased from 35.7% to 25.7%, the hardness increased from 61.2H_RC to 66.5H_RC and the grinding ratio of the vitrified bond grinding wheels to carbide alloy (YG8) increased from 11.5 to 19.1.     

Investigation on densification of Al2O3/B4C ceramic by ab initio calculation and experiment

Compared to experiment, the adsorption energies, bonding properties, and electronic structure of two different Al₂O₃/B₄C bridge sites with seven different Al₂O₃ surfaces are investigated by ab initio periodic density functional theory. The Al₂O₃/B₄C ceramic sintered in Ar is synthesized and measured by XRD and TEM. The calculated results reveal that the densification of O_bridge site of Al₂O₃/B₄C surface is better than that of Al_bridge. The Al₂O₃ (1 1 3)/B₄C with O_bridge is the most favorable and stable. The electronic structure shows that the electron hybridization exists between Al, O atoms and C, B atoms. The results indicate that the calculated results are in good agreement with the experiment.     

Preparation and magnetic properties of the conductive Co(1−x)NixFe2O4/polyaniline microsphere composites

Core-shell Co_(1−x)Ni_xFe₂O₄/polyaniline nanoparticles, where the core was Co_(1−x)Ni_xFe₂O₄ and the shell was polyaniline, were prepared by the combination of sol-gel process and in-situ polymerization methods. Nanoparticles were investigated by Fourier transform spectrometer, X-ray diffraction diffractometer, Scanning electron microscope, Differential thermal analysis and Superconductor quantum interference device. The results showed that the saturation magnetization of pure Co_(1−x)Ni_xFe₂O₄ nanoparticles were 57.57 emu/g, but Co_(1−x)Ni_xFe₂O₄/polyaniline composites were 37.36 emu/g. It was attributed to the lower content (15 wt%), smaller size and their uneven distribution of Co_(1−x)Ni_xFe₂O₄ nanoparticles in the final microsphere composites. Both Co_(1−x)Ni_xFe₂O₄ and PANI/Co_(1−x)Ni_xFe₂O₄ showed superparamagnetism.     

Experimental and detailed kinetic modeling study of the high pressure oxidation of methanol sensitized by nitric oxide and nitrogen dioxide

The perturbation of the combustion by NO_x is important in several practical systems (recent NO_x-reduction strategies, combustion with exhaust-gas recirculation in diesel and HCCI engines and for mild combustion). New experimental results were obtained for the oxidation of methanol in absence and in presence of NO or NO₂ in a fused silica jet-stirred reactor operating at 10 atm, over the temperature range 700-1100 K. Probe sampling followed by on-line FTIR analyses and off-line GC-TCD/FID analyses permitted to measure the concentration profiles of the reactants, stable intermediates and the final products. A detailed chemical kinetic modeling of the present experiments was performed. An overall good agreement between the present data and this modeling was obtained. The oxidation of methanol is significantly sensitized by NO₂, whereas the effect of NO is more limited. According to the proposed model, the mutual sensitization of the oxidation of methanol and NO proceeds through the NO to NO₂ conversion by HO₂. The increased production of OH resulting from the oxidation of NO by HO₂ promotes the oxidation of the fuel. A simplified reaction scheme can be proposed for the NO-seeded oxidation of methanol: NO + HO₂ ⇒ NO₂ + OH followed by OH + CH₃OH ⇒ H₂O + CH₂OH and CH₃O. The enhanced oxidation of methanol by addition of NO₂ is also due to additional OH production through: NO₂ + HO₂ ⇒ HONO + O₂, NO₂ + H ⇒ NO + OH and HONO ⇒ NO + OH followed by OH + CH₃OH ⇒ CH₂OH and CH₃O. The further reactions CH₂OH + O₂ ⇒ CH₂O + HO₂; CH₃O ⇒ CH₂O + H; CH₂O + OH ⇒ HCO; HCO + O₂ ⇒ HO₂ and H + O₂ ⇒ HO₂ complete the sequence whether NO or NO₂ is added.     

Low-voltage cathodoluminescence property of Li-doped Gd2−xYxO3:Eu

Cathodoluminescent (CL) spectra of Li-doped Gd_2−xY_xO₃:Eu³⁺ solid-solution (0.0?x?0.8) were investigated at low voltages (300 V-1 kV). The CL intensity is maximum for the composition of x=0.2 and gradually reduces with increasing the amount of substituted Y content. In particular, small (∼100 nm) particles of Li-doped Gd_1.8Y_0.2O₃:Eu³⁺ are obtained by firing the citrate precursors at only 650°C for 18 h. Relative red-emission intensity at 300 V of this phosphor is close to 180% in comparison with that of commercial red phosphor Y₂O₃:Eu³⁺. An increase of firing temperature to 900°C results in 400-600 nm sized spherical particles. At low voltages (300-800 V), the CL emission of 100 nm sized particles is much stronger than that of 400-600 nm sized ones. In contrast, the larger particles exhibit the higher CL emission intensity at high voltages (1-10 kV). Taking into consideration small spherical morphology and effective CL emission, Li-doped Gd_1.8Y_0.2O₃:Eu³⁺ appears to be an efficient phosphor material for low voltage field emission display.     

Oxygen flux influence on the morphological, structural and optical properties of Zn1−xMgxO thin films grown by plasma-assisted molecular beam epitaxy

The Zn_1−xMg_xO thin films were grown on Al₂O₃ substrate with various O₂ flow rates by plasma-assisted molecular beam epitaxy (P-MBE). The growth conditions were optimized by the characterizations of morphology, structural and optical properties. The Mg content of the Zn_1−xMg_xO thin film increases monotonously with decreasing the oxygen flux. X-ray diffractometer (XRD) measurements show that all the thin films are preferred (0 0 2) orientated. By transmittance and absorption measurements, it was found that the band gap of the film decreases gradually with increasing oxygen flow rate. The surface morphology dependent on the oxygen flow rate was also studied by field emission scanning electron microscopy (FE-SEM). The surface roughness became significant with increasing oxygen flow rate, and the nanostructures were formed at the larger flow rate. The relationship between the morphology and the oxygen flow rate of Zn_1−xMg_xO films was discussed.     

Luminescent properties of HTP AgGd1−xW2O8:Eux and AgGd1−x(W1−yMoy)2O8:Eux phosphor for white LED

Intense red phosphors, AgGd_1−xEu_x(W_1−yMo_y)₂O₈ (x=0.0-1.0, y=0.0-1.0), have been synthesized through traditional solid-state reaction and characterized by X-ray diffraction (XRD) and photoluminescence (PL). XRD results reveal that AgGd_1−xEu_xW₂O₈ synthesized at 1000 °C has a tetragonal crystal structure, which is named as high temperature phase (HTP) AgGdW₂O₈. All phosphors compositions with Eu³⁺ show red and green emission on excitation either in the charge-transfer or Eu³⁺ levels. Analysis of the emission spectra with different Eu³⁺ concentrations reveal that the optimum dopant concentration for Eu³⁺ is x=0.6 in the HTP AgGd_1−xEu_xW₂O₈ (x=0.0-1.0). Studies on the AgGd_0.4Eu_0.6(W_1−yMo_y)₂O₈ (y=0.0-1.0) and AgGd_1−xEu_x(W_0.7Mo_0.3)₂O₈ (x=0.0-1.0) show that the emission intensity is maximum for compositions with y=0.3 and x=0.5, respectively, and a decrease in emission intensity is observed for higher y or x values. The Mo⁶⁺ and Eu³⁺ co-doped AgGd(WO₄)₂ phosphors show higher emission intensity in comparison with the singly Eu³⁺-doped AgGd(WO₄)₂ in UV region. The intense emission of the tungstate/molybdate phosphors under 394 and 465 nm excitations, respectively, suggests that these materials are promising candidates as red-emitting phosphors for near-UV/blue GaN-based white LED for white light generation.     

Luminescence investigation of red phosphors Ca0.54Sr0.34−1.5xEu0.08Smx(MoO4)y (WO4)1−y for UV-white LED device

Ca_0.54Sr_0.34−1.5xEu_0.08Sm_x(MoO₄)_y (WO₄)_1−y red phosphors were prepared by solid-state reaction using Na⁺ as a charge compensator for light-emitting diodes (LED). The effects of Na⁺ concentration, synthesis temperature, reaction time and Eu³⁺ concentration were studied for the properties of luminescence and crystal structure of red phosphors. The results show that the optimum reaction condition is 6%, 900 °C, 2 h and 8%. The photoluminescence spectra show that red phosphors are effectively excited at 616 nm by 292, 395 and 465 nm. The wavelengths of 465 nm nicely match the widely applied emission wavelengths of blue LED chips.     

Magnetic properties and room-temperature magnetocaloric effect in the doped antipervoskite compounds Ga1−xAlxCMn3 (0≤x≤0.15)

We report the effects of Al doping on the structure, magnetic properties, and magnetocaloric effect of antiperovskite compounds Ga_1−xAl_xCMn₃ (0≤x≤0.15). Partial substitutions of Al for Ga enhance the Curie temperature (from 250 K for x=0.0 to 312 K for x=0.15) and the saturation magnetization. On increasing the doping level x, the maximum values of the magnetic entropy change (−ΔS_M) decreases while the temperature span of −ΔS_M vs. T plot broadens. Furthermore, the relative cooling power (RCP) is also studied. For 20 kOe, the RCP value tends to saturate at a high doping level (for x=0.12, 119 J/kg at 296 K). However, at 45 kOe, the RCP value increases quickly with increasing x (for x=0.15, 293 J/kg at 312 K). Considering the relatively large RCP and inexpensive raw materials, Ga_1−xAl_xCMn₃ may be alternative candidates for room-temperature magnetic refrigeration.     

The role of co-adsorbed O2 on the catalytic reduction of NO with C2H5OH on the surface of Pt(3 3 2)

The influence of pre-dosed O₂ on the catalytic reduction of NO with ¹³C₂H₅OH on the surface of stepped Pt(3 3 2) was investigated using Fourier transform infra red reflection-absorption spectroscopy (FTIR-RAS) and thermal desorption spectroscopy (TDS). We show that the oxidation of ¹³C₂H₅OH with O₂ is a very effective reaction, occurring at 150 K and giving rise to acetate. The presence of NO does not lead to any evident oxidation of ¹³C₂H₅OH irrespective of the annealing temperature. For the case of O₂ + ¹³C₂H₅OH + NO co-adlayers, oxidation of ¹³C₂H₅OH also takes place at 150 K. However, no new surface species that are supposed to be an intermediate for the production of N₂ are detected.The influence of O₂ on the production and desorption of N₂ is intimately related to both O₂ and ¹³C₂H₅OH coverage. The presence of pre-dosed O₂ does not greatly promote N₂ desorption. In fact, N₂ desorption is suppressed quantitatively with increasing O₂ coverage, after which unreacted, or left-over O atoms appear and remain on steps. It is concluded that the presence of pre-dosed O₂ does not play a role of activating reactants in the catalytic reduction of NO with ¹³C₂H₅OH on the surface of Pt(3 3 2).     

Raman scattering and room temperature ferromagnetism in Co-doped SrTiO3 particles

Raman scattering has been used to study the influence of cobalt, an effective dopant to obtain SrTiO₃ magnetic oxide, on the lattice dynamics of SrTiO₃. It is found that Co doping increases the lattice defects and induces a Raman vibration mode of 690 cm⁻¹. On the other hand, the ferromagnetism dependence on the x and annealing temperature was clearly and coherently observed in SrTi_1−xCo_xO₃ (x = 0, 0.01, 0.03 and 0.05) nanoparticles. It is found that the ferromagnetism of SrTi_1−xCo_xO₃ nanoparticles is weakly related to crystal deformation and oxygen vacancies in SrTiO₃. So, F-center model can explain the origin of the ferromagnetism in the prepared Co-doped SrTiO₃ samples. At the same time, the finding of large room-temperature ferromagnetism (1.6 emu/g) in this system would stimulate further interest in the area of more complicated ternary oxides.     

A novel UV-emitting phosphor: Li6CaB3O8.5:Pb

Pure Li₆CaB₃O_8.5 and Li₆Ca_1−xPb_xB₃O_8.5 (0.005≤x≤0.04) materials were prepared by a solution combustion synthesis method. The phase of synthesized materials was determined using the powder XRD and FTIR. The synthesized materials were investigated using spectrofluorometer at room temperature. The emission and excitation bands of the synthesized phosphors were observed at 307 and 268 nm, respectively. The dependence of the emission intensity on the Pb²⁺ concentration for the Li₆Ca_1−xPb_xB₃O_8.5 (0.005≤x≤0.04) was studied and observed that the optimum concentration of Pb²⁺ in phosphor is 0.01 mol. The Stokes shift of the synthesized phosphor was calculated to be 4740 cm^-1.     

Role of Ti in the luminescence process of Al2O3:Si,Ti

Al₂O₃:Si,Ti, prepared under oxidizing condition at high temperature, gives PL emission around 430 nm when excited with 240 nm. The Al₂O₃:C, TL/OSL phosphor, also shows emission around 430 nm, which corresponds to characteristic emission of F-center. Thus, to identify the exact nature of luminescent center in Al₂O₃:Si,Ti, fluorescence lifetime measurement studies were carried out along with the PL,TL and OSL studies. The PL and TL in Al₂O₃:Si,Ti show emission around 430 nm and the time-resolved fluorescence studies show lifetime of about 43 μs for the 430 nm emission, which is much smaller than the reported lifetime of ∼35 ms for the 430 nm emission (F-center emission) in Al₂O₃:C phosphor. Therefore, the emission observed in Al₂O₃:Si,Ti phosphor was assigned to Ti⁴⁺ charge transfer transition. Fluorescence studies of Al₂O₃:Si,Ti do not show any traces of F and F⁺ centers. Also, Ti⁴⁺ does not show any change in the charge state after gamma-irradiation. On the basis of the above studies, a mechanism for TSL/OSL process in Al₂O₃:Si,Ti is proposed.     

BiFeO3/Zn1−xMnxO bilayered thin films

BiFeO₃/Zn_1−xMn_xO (x = 0-0.08) bilayered thin films were deposited on the SrRuO₃/Pt/TiO₂/SiO₂/Si(1 0 0) substrates by radio frequency sputtering. A highly (1 1 0) orientation was induced for BiFeO₃/Zn_1−xMn_xO. BiFeO₃/Zn_1−xMn_xO thin films demonstrate diode-like and resistive hysteresis behavior. A remanent polarization in the range of 2P_r ∼ 121.0-130.6 μC/cm² was measured for BiFeO₃/Zn_1−xMn_xO. BiFeO₃/Zn_1−xMn_xO (x = 0.04) bilayer exhibits a highest M_s value of ∼15.2 emu/cm³, owing to the presence of the magnetic Zn_0.96Mn_0.04O layer with an enhanced M_s value.