Improved performance and stability by an Al/Ni bilayer cathode in organic light-emitting diodes

Al/Ni bilayer cathode was used to improve the electroluminescent (EL) efficiency and stability in N,N′-bis(1-naphthyl)-N,N′-diphenyl-1,1′ biphenyl 4,4′-dimaine (NPB)/tris-(8-hydroxyquinoline) aluminum (Alq₃)-based organic light-emitting diodes. The device with LiF/Al/Ni cathode achieved a maximum power efficiency of 2.8 lm/W at current density of 1.2 mA/cm², which is 1.4 times the efficiency of device with the state-of-the-art LiF/Al cathode. Importantly, the device stability was significantly enhanced due to the utilization of LiF/Al/Ni cathode. The lifetime at 30% decay in luminance for LiF/Al/Ni cathode was extrapolated to 400 h at an initial luminance of 100 cd/m², which is 10 times better than the LiF/Al cathode.     

Highly efficient greenish blue-emitting organic diodes based on pyrene derivatives

We report the synthesis of pyrene derivatives as the light emissive layer for highly efficient organic electroluminescence (EL) diodes. Multilayer devices were fabricated with pyrene derivatives (ITO/NPB (50 nm)/blue material (30 nm)/BCP (10 nm)/Alq₃ (30 nm)/LiF (1 nm)/Al). By using 1,1′-dipyrene (DP) and 1,4-dipyrenyl benzene (DPB), the devices produced the blue EL emissions with 1931 Commission International de L’Eclairage coordinates of (x=0.21, y=0.35) and (x=0.19, y=0.25), respectively. The device with DPB shows a maximum brightness of 42,445 cd/m² at 400 mA/cm² and the luminance efficiency of 8.57 cd/A and 5.18 lm/W at 20 mA/cm².     

High efficiency small molecule white organic light-emitting devices with a multilayer structure

In this paper, a new white organic light-emitting device (WOLED) with multilayer structure has been fabricated. The structure of devices is ITO/N, N-bis-(1-naphthyl)-N, N^′-diphenyl-1, 1′-biphenyl-4, 4′-diamine (NPB) (40 nm)/NPB: QAD (1%): DCJTB (1%) (10 nm) /DPVBi (10 nm) /2, 9-dimethyl, 4, 7-diphenyl, 1, 10-phenanthroline (BCP) (d nm)/tris-(8-hydroxyquinoline) aluminium (Alq₃)(50-d nm)/LiF (1 nm)/Al (200 nm). In our devices, a red dye 4-(dicyanomethylene)-2-t-butyl-6 (1, 1, 7, 7-tetramethyl julolidyl-9-enyl)-4H-pyran (DCJTB) and a green dye quinacridone (QAD) were co-doped into NPB. The device with 8 nm BCP shows maximum luminance of 12 852 cd/m² at 20 V. The current efficiency and power efficiency reach 9.37 cd/A at 9 V and 3.60 lm/W at 8 V, respectively. The thickness of the blocking layer permit the tuning of the device spectrum to achieve a balanced white emission with Commission International de’Eclairage (CIE) chromaticity coordinates of (0.33,0.33). The CIE coordinates of device change from (0.3278, 0.3043) at 5 V to (0.3251, 0.2967) at 20 V that are well in the white region, which is largely insensitive to the applied bias.     

Blue organic light-emitting diodes with low driving voltage and maximum enhanced power efficiency based on buffer layer MoO3

Blue organic light-emitting devices based on wide bandgap host material, 2-(t-butyl)-9, 10-di-(2-naphthyl) anthracene (TBADN), blue fluorescent styrylamine dopant, p-bis(p-N,N-diphenyl-amino-styryl)benzene (DSA-Ph) have been realized by using molybdenum oxide (MoO₃) as a buffer layer and 4,7-diphenyl-1,10-phenanthroline (BPhen) as the ETL. The typical device structure used was glass substrate/ITO/MoO₃ (5 nm)/NPB (30 nm)/[TBADN: DSA-Ph (3 wt%)](35 nm)/BPhen (12 nm)/LiF (0.8 nm)/Al (100 nm). It was found that the MoO₃∥BPhen-based device shows the lowest driving voltage and highest power efficiency among the referenced devices. At the current density of 20 mA/cm², its driving voltage and power efficiency are 5.4 V and 4.7 Lm/W, respectively, which is independently reduced 46%, and improved 74% compared with those the m-MTDATA∥Alq₃ is based on, respectively. The J-V curves of ‘hole-only’ devices reveal that a small hole injection barrier between MoO₃∥NPB leads to a strong hole injection, resulting low driving voltage and high power efficiency. The results strongly indicate that carrier injection ability and balance shows a key significance in OLED performance.     

Efficient white organic light-emitting devices using 4,7-diphenyl-1,10-phenanthroline as block layer

A white light-emitting device has been fabricated with a structure of ITO/m-MTDATA (45 nm)/NPB (10 nm)/DPVBi (8 nm)/DPVBi:DCJTB 0.5% (15 nm)/BPhen (x nm)/Alq₃ [(55−x) nm]/LiF (1 nm)/Al, with x=0, 4, and 7. BPhen was used as the hole-blocking layer. This results in a mixture of lights from DPVBi molecules (blue-light) and DCJTB (yellow-light) molecules, producing white light emission. The chromaticity can be readily adjusted by only varying the thickness of the BPhen layer. The CIE coordinates of the device are largely insensitive to the driving voltages. When the thickness of BPhen is 7 nm, the device exhibits peak efficiency of 6.87 cd/A (3.59 lm/W) at the applied voltage of 6 V, the maximum external quantum efficiency η_ext=2.07% corresponding to 6.18 cd/A, and the maximum brightness is 18494 cd/m² at 15 V.     

Improvement of performance of tetraphenylporphyrin-based red organic light emitting diodes using WO3 and C60 buffer layers

One of the porphyrin derivatives, meso-tetraphenylporphyrin (TPP), has been synthesized and examined as an emitter material (EM) for efficient fluorescent red organic light-emitting diodes (OLEDs). By inserting a tungsten oxide (WO₃) layer into the interface of anode (ITO) and hole transport layer N,N′-Di-[(1-napthyl)-N,N′-diphenyl]-(1,1′-biphenyl)-4,4′-diamine (NPB) and by using fullerene (C₆₀) in contact with a LiF/Al cathode, the performance of devices was markedly improved. The current density–voltage–luminance (J–V–L) characterizations of the samples show that red OLEDs with both WO₃ and C₆₀ as buffer layers have a lower driving voltage and higher luminance compared with the devices without buffer layers. The red OLED with the configuration ITO/WO₃ (3 nm)/NPB (50 nm)/TPP (60 nm)/BPhen (30 nm)/C₆₀ (5 nm)/LiF (0.8 nm)/Al (100 nm) achieved the high luminance of 6359 cd/m² at the low driving voltage of 8 V. At a current density of 20 mA/cm², a pure red emission with CIE coordinates of (0.65; 0.35) is observed for this device. Moreover, a power efficiency of 2.07 lm/W and a current efficiency of 5.17 cd/A at 20 mA/cm² were obtained for the fabricated devices. The study of the energy level diagram of the devices revealed that the improvement in performance of the devices with buffer layers could be attributed to lowering of carrier-injecting barrier and more balanced charge injection and transport properties.     

Investigation of an efficient YbF3/Al cathode for tris-(8-hydroxyquinoline)aluminum-based small molecular organic light-emitting diodes

Efficient tris-(8-hydroxyquinoline)aluminum (Alq₃)-based organic light-emitting diodes (OLEDs) using YbF₃ as the electron injection layer have been investigated. With an YbF₃ (3.0 nm)/Al cathode, the device with Alq₃ as the emitting layer achieved a better performance than the control device with a LiF (0.5 nm)/Al cathode. The release of the low-work-function metal Yb is responsible for the performance enhancement. From the analysis by atomic force spectroscopy and X-ray photoemission spectroscopy, it is observed that the Alq₃-cathode interface could be well covered by YbF₃ at an optimum thickness of 3.0 nm, which helps to prevent the contact between Alq₃ and Al, and to reduce the destruction of Alq₃ by Al.     

Optimized Performances of Thick Film Organic Lighting-Emitting Diodes

The performance of organic light-emitting diodes (OLEDs) with thick film is optimized. The alternative vanadium oxide (V₂O₅) and N,N'-di(naphthalene-1-yl)-N,N'-diphenyl-benzidine (NPB) layers are used to enhance holes in the emissive region, and 4,7-dipheny-1,10-phenanthroline (Bphen) doped 8-tris-hydroxyquinoline aluminium (Alq₃) is used to enhance electrons in the emissive region, thus ITO/V₂O₅ (8nm)/NPB (52nm)/V₂O₅ (8nm)/NPB (52nm)/Alq₃ (30 and 45nm)/Alq₃:Bphen (30wt%, 30 and 45nm)/LiF (1nm)/Al (120nm) devices are fabricated. The thick-film devices show the turn-on voltage of about 3V and the maximal power efficiency of 4.5lm/W, which is 1.46 times higher than the conventional thin-film OLEDs.     

High-efficiency Simple Structure White Organic Light-emitting Devices Based on Rubrene Ultrathin Layer

White organic light-emitting devices (WOLEDs) were fabricated with an ultrathin layer of rubrene inserted between NPB and TPBI. With a simple three-layer structure of ITO/NPB(50 nm)/rubrene(0.1 nm)/TPBI(50 nm)/LiF/Al, a white light with CIE coordinates of (0.31, 0.30) were generated. The device gave a maximum luminance efficiency of 2.04 lm/W at 5 V. Furthermore, with a multilayer structure of ITO/m-MTDATA(30 nm)/NPB(20 nm)/rubrene(0.1 nm)/TPBI(40 nm)/Alq₃(10 nm)/LiF/Al, the device reached a maximum luminance efficiency of 4.29 lm/W at 4 V and the luminance could exceed 10 000 cd/m² at 10 V.     

Synthesis and electroluminescent properties of a carbozole-functionalized europium(III) complex

A novel europium(III) complex, tris(dibenzoylmethanate){1-[9-hexyl-9H-carbazole]-2-(2-pyridyl)-benzimidazole}europium(III) [Eu(DBM)₃(CAR-PyBM)] functionalized by a carbozole fragment, was synthesized and used as emitting material in organic electroluminescent (EL) devices. Compared with the device based on an unfunctional Eu(III) complex, [Eu(DBM)₃HPyBM] (HPyBM=2-(2-pyridyl)benzimidazole), the EL performances of the device using [Eu(DBM)₃(CAR-PyBM)] as an emitter was significantly enhanced due to the improvement of hole-transporting ability. The maximum efficiency and luminance of red emission achieved from the device with the configuration of ITO/N,N′-diphenyl-N,N′-bis(3-methylphenyl)-1,1′-biphenyl-4,4′diamine (TPD, 50 nm)/ [Eu(DBM)₃(CAR-PyBM)] (30 nm)/1,3,5-tirs-(N-phenylbenzimidazol-2-yl)benzene (TPBI, 20 nm)/LiF (1.5 nm)/Al were 4.2 cd/A and 200 cd/m², respectively.     

New double graded structure for enhanced performance in white organic light emitting diode

This study presents a new design that uses a combination of a graded hole transport layer (GH) structure and a gradually doped emissive layer (GE) structure as a double graded (DG) structure to improve the electrical and optical performance of white organic light-emitting diodes (WOLEDs). The proposed structure is ITO/m-MTDATA (15 nm)/NPB (15 nm)/NPB: 25% BAlq (15 nm)/NPB: 50% BAlq (15 nm)/BAlq: 0.5% Rubrene (10 nm)/BAlq: 1% Rubrene (10 nm)/BAlq: 1.5% Rubrene (10 nm)/Alq₃ (20 nm)/LiF (0.5 nm)/Al (200 nm). (m-MTDATA: 4,4′,4″ -tris(3-methylphenylphenylamino)triphenylamine; NPB: N,N′-diphenyl-N,N′-bis(1-naphthyl-phenyl)-(1,1′-biphenyl)-4,4′-diamine; BAlq: aluminum (III) bis(2-methyl-8-quinolinato) 4-phenylphenolate; Rubrene: 5,6,11,12-tetraphenylnaphthacene; Alq₃: tris-(8-hydroxyquinoline) aluminum). By using this structure, the best performance of the WOLED is obtained at a luminous efficiency at 11.8 cd/A and the turn-on voltage of 100 cd/m² at 4.6 V. The DG structure can eliminate the discrete interface, and degrade surplus holes, the electron-hole pairs are efficiently injected and balanced recombination in the emissive layer, thus the spectra are unchanged under various drive currents and quenching effects can be significantly suppressed. Those advantages can enhance efficiency and are immune to drive current density variations.     

利用LiF/Al作为电极的有机电致发光器件

本文报道了利用LiF/Al作为负电极的有机电致发光器件,器件结构为ITO/TPD/Alq3/LiF/Al,LiF层的加入增强了电子注入,当其厚度为0.4nm时,器件的性能最好,与单层Al和Mg/Al电极的同类器件相比,此时器件的开启电压由Al电极时的4.3V和Mg/Al电极时的3.0V降低到了2.0V,器件的最大亮度分别由4000cd/m²、14000cd/m²提高到19600cd/m²,器件的发光效率也分别增加了5倍和2倍,达到2.66lm/W.     

Affect of the electrical characteristics depending on the hole and electron injection materials of red organic light-emitting diodes

This study examined the electrical and optical properties of red OLEDs (organic light-emitting diodes) with a four-layer structure, ITO/amorphous fluoropolymer (AF)/N,N′-diphenyl-N,N′-bis(3-methylphenyl)-1,1-biphenyl-4,4′-diamine (TPD)/R-H:R-D/lithium fluoride (LiF)/Al, containing a hole injection material, AF (amorphous fluoropolymer) and an electron injection layer material, LiF. Compared to the basic structure (two-layer structure), the brightness and luminous efficiency of the four-layer structure, ITO/TPD/R-H:R-D/Al, increased approximately 100 times (30,000 lm/m²) and 150 times (51 lm/W), respectively, with an applied voltage. The excellent efficiency of the external proton was also increased 150 times (0.51%). That is, the hole and electron injection layers improved the surface roughness of ITO and Al, and the interfacial physical properties. In addition, these layers allowed the smooth injection of holes and electrons. The luminance, luminous efficiency and external quantum efficiency were attributed to an increase in the recombination rates.     

The effect of alkaline metal chlorides on the properties of organic light-emitting diodes

The multilayer organic light-emitting diodes (OLEDs) have been fabricated with a thin alkaline metal chloride layer inserted inside an electron transport layer (ETL), tris (8-hydroxyquinoline) aluminum (Alq₃). The alkaline metal chloride layer was inserted inside 60 nm Alq₃ at d=0, 10, 20 and 30 nm positions (d is the distance of the interlayer away from the Al cathode). The devices, with alkaline metal chlorides inserted at the Alq₃/Al interface, showed electron injection and electroluminescence (EL) intensity improvements. When the alkaline metal chlorides were inserted inside the Alq₃ layer at 10, 20 or 30 nm position apart from the Al cathode, both EL intensity and efficiency were enhanced for the devices with a thin potassium chloride (KCl) or rubidium chloride (RbCl) layer. On the contrary, the improvements were not observed for the OLEDs with a thin sodium chloride (NaCl) layer. A proposed insulator buffer layer model is employed to explain these characteristics of the devices.     

Reduction of driving voltage in organic light-emitting diodes with molybdenum trioxide in CuPc/NPB interface

A novel structure of organic light-emitting diode was fabricated by inserting a molybdenum trioxide (MoO₃) layer into the interface of hole injection layer copper phthalocyanine (CuPc) and hole transport layer N,N′-diphenyl-N,N′-bis(1-napthyl-phenyl)-1,1′-biphenyl-4,4′-diamine (NPB). It has the configuration of ITO/CuPc(10 nm)/MoO₃(3 nm)/NPB(30 nm)/ tris-(8-hydroxyquinoline) aluminum (Alq₃)(60 nm)/LiF(0.5 nm)/Al. The current density-voltage-luminance (J-V-L) performances show that this structure is beneficial to the reduction of driving voltage and the enhancement of luminance. The highest luminance increased by more than 40% compared to the device without hole injection layer. And the driving voltage was decreased obviously. The improvement is ascribed to the step barrier theory, which comes from the tunnel theory. The power efficiency was also enhanced with this novel device structure. Finally, “hole-only” devices were fabricated to verify the enhancement of hole injection and transport properties of this structure.     

Synthesis and luminescent properties of two Schiff-base boron complexes

Schiff bases N,N′-o-phenylenebis (salicylideneimine) (H₂L¹), N,N′-p-phenylenebis (salicylideneimine) (H₂L²) and their corresponding boron complexes (BF₂)₂L¹, (BF₂)₂L² were synthesized, respectively. The two boron complexes have been characterized by ¹H NMR, mass spectrometry and elemental analysis, while the luminescent properties of them were investigated with UV-VIS spectroscopy and photoluminescence spectroscopy. Then the three-layer devices [ITO/NPB (60 nm)/(BF₂)₂L¹ (50 nm)/Alq3 (20 nm)/LiF (1 nm)/Al (200 nm)] (device I) and [ITO/NPB (60 nm)/(BF₂)₂L² (50 nm)/Alq3 (20 nm)/LiF (1 nm)/Al (200 nm)] (device II) were fabricated by vacuum deposition. These two devices both exhibited blue green emission at 500 nm, but showed different luminances and efficiencies.     

Bright electrophosphorescent devices based on sterically hindered spacer-containing Cu(I) complex

A Cu(I) complex, [Cu(Dppp)(DPEphos)]BF₄ (Dppp=2,3-diphenyl-pyrazino[2,3-f][1,10]phenanthroline, DPEphos=Bis[2-(diphenylphosphino)phenyl]ether), is synthesized and used as the dopant in bright electrophosphorescent devices with the general structure ITO/m-MTDATA (30 nm)/NPB (20 nm)/CBP: ×wt% [Cu(Dppp)(DPEphos)]BF₄ (30 nm)/Bphen (20 nm)/Alq₃ (20 nm)/LiF (0.8 nm)/ Al (200 nm). These devices exhibit a maximum brightness of 4483 cd/m² and a peak efficiency of 3.4 cd/A. Compared with previously reported similar devices based on Cu(I) complexes, the brightness of the devices presented in this article is the best. Meanwhile, 2% [Cu(Dppp)(DPEphos)]BF₄-based devices exhibit white light-emitting properties with CIE coordinates of (0.32. 0.35) at 10 V.     

High-performance organic red-light-emitting device based on DCJTB and a new host material

An efficient red-light-emitting device using a new host material (DPF) and a red dopant (DCJTB) with a configuration of ITO/NPB (50 nm)/DCJTB:DPF (2%, 10 nm)/TPBI (30 nm)/LiF (0.5 nm)/Mg:Ag has been fabricated and investigated. The red OLED yields a brightness of 9270 cd/m² at 10 V, a maximum current efficiency of 4.2 cd/A and a maximum power efficiency of 3.9 lm/W. Using DPF as host material, the performance is much better than that of a prototypical Alq₃-based device, which has a maximum efficiency of 1.9 cd/A and 0.6 lm/W. The performance is even comparable with red OLEDs using an assist dopant or a cohost emitter system. Results of this work indicate that DPF is a promising host material for red OLEDs with high efficiency and simple device structure.     

A terbium (III) complex with triphenylamine-functionalized ligand for organic electroluminescent device

A novel ligand, 4-diphenylamino-benzoic acid (HDPAB), and the corresponding Tb (III) complex, Tb (DPAB)₃ which can be dissolved easily in organic solvents were synthesized and characterized. Organic electroluminescent (EL) device with a structure of indium tin oxide (ITO)/poly(N-vinylcarbazole) (PVK): Tb (DPAB)₃ (50 wt%, 80 nm)/1,3,5-tris-(N-phenylbenzimidazol-2-yl)benzene (TPBI) (30 nm)/tri(8-hydroxyquinoline)aluminum (AlQ) (20 nm)/LiF (1 nm)/Al (150 nm) in which Tb (DPAB)₃ acted as an emitter were fabricated. The maximum luminance of 230 cd m⁻² at 20 V and the maximum efficiency of 0.62 cd A⁻¹ were obtained due to the introduction of hole-transporting group, representing the best result to date among Tb (III) carboxylate complexes based EL devices. These results indicate that modifications of rare earth complexes are a promising way to improve the properties of EL devices.     

Photoluminescence and electroluminescence of a novel green-yellow emitting material-5,6-Bis-[4-(naphthalene-1-yl-phenyl-amino)-phenyl]-pyrazine-2,3-dicarbonitrile

A new compound with intramolecular charge transfer (ICT) property—5,6-Bis-[4-(naphthalene-1-yl-phenyl-amino)-phenyl]-pyrazine-2,3-dicarbonitrile(BNPPDC) was synthesized. The new compound was strongly fluorescent in non-polar and moderately polar solvents, as well as in thin solid film. The absorption and emission maxima shifted to longer wavelength with increasing solvent polarity. The fluorescence quantum yield also increased with increasing solvent polarity from non-polar to moderately polar solvents, then decreased with further increase of solvent polarity. This indicates both “positive” and “negative” solvatokinetic effects co-existed. Using this material as hole-transporting emitter and host emitter, we fabricated two electroluminescent (EL) devices with structures of A (ITO/BNPPDC (45 nm)/1,3,5-tris(N-phenylbenzimidazol-2-yl)benzene (TPBI) (45 nm)/Mg:Ag (200 nm) and B (ITO/N,N′-diphenyl-N,N′-bis-(3-methylphenyl) (1,1′-diphenyl)4,4′-diamine (TPD) (50 nm)/BNPPDC (20 nm)/1,3,5-tris(N-phenylbenzimidazol-2-yl)benzene (TPBI) (45 nm)/Mg:Ag (200 nm). The devices showed green-yellow EL emission with good efficiency and high brightness. For example, the device A exhibited a high brightness of 17400 cd/m² at a driving voltage of 11 V and a very low turn-on voltage (2.9 V), as well as a maximum luminous efficiency 3.61 cd/A. The device B showed a similar performance with a high brightness of 12650 cd/m² at a driving voltage of 13 V and a maximum luminous efficiency 3.62 cd/A. In addition, the EL devices using BNPPDC as a host and 4-(dicyanomethylene)-2-t-butyl-6-(1,1,7,7-tetramethyljulolidyl-9-enyl)-4H-pyran (DCJTB) as a dopant (configuration: ITO/TPD (60 nm)/BNPPDC:DCJTB (2%) (30 nm)/TPBI (35 nm)/Mg:Ag (200 nm)) showed a good performance with a brightness of 150 cd/m² at 4.5 V, a maximum brightness of 12600 cd/m² at 11.5 V, and a maximum luminous efficiency of 3.30 cd/A.