High-density plasma etching of indium-zinc oxide films in Ar/Cl2 and Ar/CH4/H2 chemistries

The dry etching characteristics of transparent and conductive indium-zinc oxide (IZO) films have been investigated using an inductively coupled high-density plasma. While the Cl₂-based plasma mixture showed little enhancement over physical sputtering in a pure argon atmosphere, the CH₄/H₂/Ar chemistry produced an increase of the IZO etch rate. On the other hand, the surface morphology of IZO films after etching in Ar and Ar/Cl₂ discharges is smooth, whereas that after etching in CH₄/H₂/Ar presents particle-like features resulting from the preferential desorption of In- and O-containing products. Etching in CH₄/H₂/Ar also produces formation of a Zn-rich surface layer, whose thickness (∼40 nm) is well-above the expected range of incident ions in the material (∼1 nm). Such alteration of the IZO layer after etching in CH₄/H₂/Ar plasmas is expected to have a significant impact on the transparent electrode properties in optoelectronic device fabrication.     

Comparison of CH4/H2 and C2H6/H2 inductively coupled plasma etching of ZnO

CH₄/H₂-based discharges are attractive for dry etching of single crystal ZnO because of their non-corrosive nature. We show that substitution of C₂H₆ for CH₄ increases the ZnO etch rate by approximately a factor of 2 both with and without any inert gas additive. The C₂H₆/H₂/Ar mixture provides a strong enhancement over pure Ar sputtering, in sharp contrast to the case of CH₄/H₂/Ar. The threshold ion energy for initiating etching is 42.4 eV for C₂H₆/H₂/Ar and 59.8 eV for CH₄/H₂/Ar. The etched surface morphologies were smooth, independent of the chemistry and the Zn/O ratio in the near-surface region was unchanged within experimental error after etching with both chemistries. The plasma etching improved the band-edge photoluminescence intensity and suppressed the deep level emission from the bulk ZnO under our conditions, due possibly to removal of surface contamination layer.     

Dry etching of MgCaO gate dielectric and passivation layers on GaN

MgCaO films grown by rf plasma-assisted molecular beam epitaxy and capped with Sc₂O₃ are promising candidates as surface passivation layers and gate dielectrics on GaN-based high electron mobility transistors (HEMTs) and metal-oxide semiconductor HEMTs (MOS-HEMTs), respectively. Two different plasma chemistries were examined for etching these thin films on GaN. Inductively coupled plasmas of CH₄/H₂/Ar produced etch rates only in the range 20-70 Å/min, comparable to the Ar sputter rates under the same conditions. Similarly slow MgCaO etch rates (∼100 Å/min) were obtained with Cl₂/Ar discharges under the same conditions, but GaN showed rates almost an order of magnitude higher. The MgCaO removal rates are limited by the low volatilities of the respective etch products. The CH₄/H₂/Ar plasma chemistry produced a selectivity of around 2 for etching the MgCaO with respect to GaN.     

Dry etching of bulk single-crystal ZnO in CH4/H2-based plasma chemistries

The effect of inert gas additive (He, Ar, Xe) to CH₄/H₂ discharges for dry etching of single crystal ZnO was examined. The etch rates were higher with Ar or Xe addition, compared to He but in all cases the CH₄/H₂-based mixtures showed little or no enhancement over pure physical sputtering under the same conditions. The etched surface morphologies were smooth, independent of the inert gas additive species and the Zn/O ratio in the near-surface region decreases as the mass number of the additive species increases, suggesting preferential sputtering of O. The plasma etching improved the band-edge photoluminescence intensity from the ZnO for the range of ion energies used here (290-355 eV), due possibly to removal of surface contamination layer.     

Elucidating surface properties of dry-etched ZnO using H2/CH4 and H2/CH4/Ar plasma

This paper reports a study of reactive ion etching (RIE) of n-ZnO in H₂/CH₄ and H₂/CH₄/Ar gas mixtures. Variables in the experiment were gas flow ratios, radio-frequency (rf) plasma power, and total pressure. Structural and electrical parameters of the etched surfaces and films were determined. Both the highest surface roughness and highest etching rate of ZnO films were obtained with a maximum rf power of 300 W, but at different gas flow ratios and working pressures. These results were expected because increasing the rf power increased the bond-breaking efficiency of ZnO. The highest degree of surface roughness was a result of pure physical etching by H₂ gas without mixed CH₄ gas. The highest etching rate was obtained from physical etching of H₂/Ar species associated with chemical reaction of CH₄ species. Additionally, the H₂/CH₄/Ar plasma treatment drastically decreased the specific contact and sheet resistance of the ZnO films. These results indicated that etching the ZnO film had roughened the surface and reduced its resistivity to ohmic contact, supporting the application of a roughened transparent contact layer (TCL) in light-emitting diodes (LEDs).     

Comparison of plasma chemistries for the dry etching of bulk single-crystal zinc-oxide and rf-sputtered indium-zinc-oxide films

The dry etching characteristics of bulk, single-crystal zinc-oxide (ZnO) and rf-sputtered indium-zinc-oxide (IZO) films have been investigated using an inductively coupled high-density plasma with different plasma chemistries. The introduction of interhalogens such as ICl, IBr, BI₃, and BBr₃ to the Ar plasma produced no enhancement of the ZnO and IZO etch rates with respect to physical sputtering in a pure argon atmosphere under the same experimental conditions. In these plasma chemistries, the etch rate of both materials increased with source power and ion energy, indicating that ion bombardment plays an important role in enhancing desorption of etch products. Except in Ar/CH₄/H₂ discharges, the ZnO etch rate was very similar to that of IZO, which indicates that zinc and indium atoms are driven by a similar plasma etching dynamic. CH₄/H₂-containing plasmas produced higher etch rates for IZO than for ZnO due to the preferential desorption of the group III etch products. Application of the CH₄/H₂/Ar plasma to the etching of deep features in bulk, single-crystal ZnO produced highly anisotropic profiles although some trenches were observed near the sidewalls.     

Etching and oxidation of InAs in planar inductively coupled plasma

The surface of InAs (1 1 1)A was investigated under plasmachemical etching in the gas mixture CH₄/H₂/Ar. Etching was performed using the RF (13.56 MHz) and ICP plasma with the power 30–150 and 50–300 W, respectively; gas pressure in the reactor was 3–10 mTorr. It was demonstrated that the composition of the subsurface layer less than 5 nm thick changes during plasmachemical etching.A method of deep etching of InAs involving ICP plasma and hydrocarbon based chemistry providing the conservation of the surface relief is proposed. Optimal conditions and the composition of the gas phase for plasmachemical etching ensuring acceptable etch rates were selected.     

Nanometer-scale etching of CoFeB thin films using pulse-modulated high density plasma

Pulse-modulated inductively coupled plasma reactive ion etching of nanometer-scale patterned CoFeB thin films was performed in CH₄/O₂/Ar gas mixture. As the pulse on-off duty ratio decreased, the etch selectivity of CoFeB/TiN slightly increased and the etch profiles were improved. Moreover, the etch selectivity of the CoFeB films and the etch profiles were improved with the increase in the pulse frequency of the plasma. X-ray photoelectron spectroscopy revealed that during the pulse-modulated etching in the CH₄/O₂/Ar gas mixture, some polymeric layers were formed on the CoFeB films, which helped prevent the lateral etching and increased the etch selectivity. Consequently, nanometer-scale etching of CoFeB thin films patterned with TiN hard masks could be achieved using pulsed-modulated plasma in CH₄/O₂/Ar gas mixture.     

Investigation of etch characteristics of non-polar GaN by wet chemical etching

We characterized the surface defects in a-plane GaN, grown onto r-plane sapphire using a defect-selective etching (DSE) method. The surface morphology of etching pits in a-plane GaN was investigated by using different combination ratios of H₃PO₄ and H₂SO₄ etching media. Different local etching rates between smooth and defect-related surfaces caused variation of the etch pits made by a 1:3 ratio of H₃PO₄/H₂SO₄ etching solution. Analysis results of surface morphology and composition after etching by scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS) demonstrated that wet chemical etching conditions could show the differences in surface morphology and chemical bonding on the a-plane GaN surface. The etch pits density (EPD) was determined as 3.1 × 10⁸ cm⁻² by atom force microscopy (AFM).     

Reactive ion etching of FePt using inductively coupled plasma

We propose a reactive ion etching (RIE) process of an L1₀-FePt film which is expected as one of the promising materials for the perpendicular magnetic recording media. The etching was carried out using an inductively coupled plasma (ICP) RIE system and an etching gas combination of CH₄/O₂/NH₃ was employed. The L1₀-FePt films were deposited on (1 0 0)-oriented MgO substrates using a magnetron sputtering system. The etching masks of Ti were patterned on the FePt films lithographically. The etch rates of ∼16 and ∼0 nm/min were obtained for the FePt film and the Ti mask, respectively. The atomic force microscopy (AFM) analyses provided the average roughness (R_a) value of 0.95 nm for the etched FePt surface, that is, a very flat etched surface was obtained. Those results show that the highly selective RIE process of L1₀-FePt was successfully realized in the present study.     

Self assembled micro masking effect in the fabrication of SiC nanopillars by ICP-RIE dry etching

This report presents the results of the novel fabrication of 4H-SiC pillars with nanopores using ICP-RIE dry etching. Cl₂/Ar gas plasma with various mass flow rates was used in this etching process to produce SiC nanopillars without using patterned etch mask. Cylindrical pillars of 300 nm diameter and 500 nm height with smooth side walls were etched on SiC wafer. The etching condition for the optimized fabrication of SiC nanopillars is presented in this report. Each nanopillar has been produced with a nanosize pore at the center along its length and up to the middle of the cylindrical nanopillar; it is a unique feature has not ever been reported in case of SiC. Inclusion of oxygen was found influence the formation of nanopillars by the effect of SiO₂ micro masking. The formation of self assembled SiO₂ layer and its micro masking effect in the fabrication of this unique nanostructure has been investigated using TEM, STEM and EDAX measurements.     

Methane/propane oxidation at high pressures: Experimental and detailed chemical kinetic modeling

Shock tube experiments and chemical kinetic modeling were performed to further understand the ignition and oxidation kinetics of various methane-propane fuel blends at gas turbine pressures. Ignition delay times were obtained behind reflected shock waves for fuel mixtures consisting of CH₄/C₃H₈ in ratios ranging from 90/10% to 60/40%. Equivalence ratios varied from lean (? = 0.5), through stoichiometric to rich (? = 3.0) at test pressures from 5.3 to 31.4 atm. These pressures and mixtures, in conjunction with test temperatures as low as 1042 K, cover a critical range of conditions relevant to practical turbines where few, if any, CH₄/C₃H₈ prior data existed. A methane/propane oxidation mechanism was prepared to simulate the experimental results. It was found that the reactions involving CH₃O˙, CH₃O˙₂, and ?H₃ + O₂/HO˙₂ chemistry were very important in reproducing the correct kinetic behavior.     

An optical emission spectroscopy study of the plasma generated in the DC HF CVD nucleation of diamond

Optical emission spectroscopy (OES) was used to study the plasma generated by the activation of the gas phase CH₄ + H₂ both by hot filaments and by a plasma discharge (DC HF CVD) during the nucleation of CVD diamond. The effects of nucleation parameters, such as methane concentration and extraction potential, on the plasma chemistry near the surface were investigated. The density of the diamond nucleation and the quality of the diamond films were studied by scanning electron microscopy (SEM) and Raman scattering, respectively. The OES results showed that the methane concentration influenced strongly the intensity ratio of H_β-H_α implying an increase of electron mean energy, as well as CH, CH⁺, C₂. A correlation between the relative increase of CH⁺ and the diamond nucleation density was found, conversely the increase of C₂ contributed to the introduction of defects in the diamond nuclei.     

Electronic and annealing properties of the E0.31 defect introduced during Ar plasma etching of germanium

Low energy (±80 eV) Ar plasma etching has been successfully used to etch several semiconductors, including GaAs, GaP, and InP. We have studied the only prominent defect, E_0.31, introduced in n-type Sb-doped Ge during this process by deep level transient spectroscopy (DLTS). The E_0.31 defect has an energy level at 0.31 eV below the conduction band and an apparent capture cross-section of 1.4×10⁻¹⁴ cm². The fact that no V-Sb defects and no interstitial-related defects were observed implies that the etch process did not introduce single vacancies or single interstitials. Instead it appears that higher order vacancy or interstitial clusters are introduced due to the large amount of energy deposited per unit length along the path of the Ar ions in the Ge. The E_0.31 defect may therefore be related to one of these defects. DLTS depth profiling revealed the E_0.31 concentration had a maximum (6×10¹³ cm⁻³) close to the Ge surface and then it decreased more or less exponentially into the Ge. Finally, annealing at 250 °C reduced the E_0.31 concentration to below the DLTS detection limit.     

Microstructuring of fused silica by laser-induced backside wet etching using picosecond laser pulses

The laser-induced backside wet etching (LIBWE) is an advanced laser processing method used for structuring transparent materials. LIBWE with nanosecond laser pulses has been successfully demonstrated for various materials, e.g. oxides (fused silica, sapphire) or fluorides (CaF₂, MgF₂), and applied for the fabrication of microstructures. In the present study, LIBWE of fused silica with mode-locked picosecond (t_p = 10 ps) lasers at UV wavelengths (λ₁ = 355 nm and λ₂ = 266 nm) using a (pyrene) toluene solution was demonstrated for the first time. The influence of the experimental parameters, such as laser fluence, pulse number, and absorbing liquid, on the etch rate and the resulting surface morphology were investigated. The etch rate grew linearly with the laser fluence in the low and in the high fluence range with different slopes. Incubation at low pulse numbers as well as a nearly constant etch rate after a specific pulse number for example were observed. Additionally, the etch rate depended on the absorbing liquid used; whereas the higher absorption of the admixture of pyrene in the used toluene enhances the etch rate and decreases the threshold fluence. With a λ₁ = 266 nm laser set-up, an exceptionally smooth surface in the etch pits was achieved. For both wavelengths (λ₁ = 266 nm and λ₂ = 355 nm), LIPSS (laser-induced periodic surface structures) formation was observed, especially at laser fluences near the thresholds of 170 and 120 mJ/cm², respectively.     

Effect of H2 and O2 plasma etching treatment on the surface of diamond-like carbon thin film

In this study, we investigated the surface properties of diamond-like carbon (DLC) films for biomedical applications through plasma etching treatment using oxygen (O₂) and hydrogen (H₂) gas. The synthesis and post-plasma etching treatment of DLC films were carried out by 13.56 MHz RF plasma enhanced chemical vapor deposition (PECVD) system. In order to characterize the surface of DLC films, they were etched to a thickness of approximately 100 nm and were compared with an as-deposited DLC film. We obtained the optimum condition through power variation, at which the etching rate by H₂ and O₂ was 30 and 80 nm/min, respectively. The structural and chemical properties of these thin films after the plasma etching treatment were evaluated by Raman and Fourier transform infrared (FT-IR) spectroscopy. In the case of as-deposited and H₂ plasma etching-treated DLC film, the contact angle was 86.4° and 83.7°, respectively, whereas it was reduced to 35.5° in the etching-treated DLC film in O₂ plasma. The surface roughness of plasma etching-treated DLC with H₂ or O₂ was maintained smooth at 0.1 nm. These results indicated that the surface of the etching-treated DLC film in O₂ plasma was hydrophilic as well as smooth.     

The influence of H2/(H2 + Ar) ratio on microstructure and optoelectronic properties of microcrystalline silicon films deposited by plasma-enhanced CVD

Hydrogenated microcrystalline silicon films were deposited by glow discharge decomposition of SiH₄ diluted in mixed gas of Ar and H₂. By investigating the dependence of the film crystallinity on the flow rates of Ar and H₂, we showed that the addition of Ar in diluted gas markedly improves the crystallinity due to an enhanced dissociation of SiH₄. The infrared-absorption spectrum reveals that the fraction of SiH bonding increases with increasing the rate ratio of H₂/(H₂ + Ar). The surface roughness of the films increases with increasing the flow rate ratio of H₂/(H₂ + Ar), which is attributed to the decrease of massive bombardment of Ar ions in the plasma. Refractive index and absorption coefficient of the films were obtained by simulating the optical transmission spectra using a modified envelope method. Electrical measurements of the films show that the dark conductivity increases and the activation energy decreases with the ratio of H₂/(H₂ + Ar). A reasonable explanation is presented for the dependence of the microstructure and optoelectronic properties on the flow rate ratio of H₂/(H₂ + Ar).     

Dielectric barrier discharge plasma torch treatment of pyrolysis fuel oil in presence of methane and ethane

For the first time, atmospheric-pressure low-temperature plasma treatment of pyrolysis fuel oil (PFO) was investigated in dielectric barrier discharge (DBD) plasma torch reactor. Main parameters including working gas flow rate and Ar/CH₄ ratio along with the effects of separate Ar/C₂H₆ on the cracking of PFO were studied. By increasing the flow of argon and methane, the production rate of hydrocarbons containing ethane, ethylene, acetylene, propane, propylene, C₄, and C₅ increased from 1.72 to 10.48 ml/min for 4000 ml/min argon plus 400 ml/min methane as the working gas. In this case, the production rate of hydrogen increases from 10.58 to 56.86. The production rate of hydrocarbons increased from 3.53 to 13.5 ml/min by decreasing Ar/CH₄ ratio from 40 to 5.6. By changing the type of working gas from methane to ethane, the production of hydrocarbons considerably increased from 6.47 to 17.75 ml/min.     

A study on the wet etching behavior of AZO (ZnO:Al) transparent conducting film

This paper studies the wet etching behavior of AZO (ZnO:Al) transparent conducting film with tetramethylammonium hydroxide (TMAH). The optimum optoelectronic film is prepared first using designated RF power, film thickness and controlled annealing heat treatment parameters. The AZO film is then etched using TMAH etchant and AZ4620 photoresist with controlled etchant concentration and temperature to examine the etching process effect on the AZO film optoelectronic properties. The experimental results show TMAH:H₂O = 2.38:97.62 under 45 °C at the average etch rate of 22 nm/min as the preferred parameters. The activation energy drops as the TMAH concentration rises, while the etch rate increases along with the increase in TMAH concentration and temperature. After lithography, etching and photoresist removal, the conductivity of AZO film dramatically drops from 2.4 × 10⁻³ Ω cm to 3.0 × 10⁻³ Ω cm, while its transmittance decreases from 89% to 83%. This is due to the poor chemical stability of AZO film against AZ4620 photoresist, leading to an increase in surface roughness. In the photoresist postbaking process, carbon atoms diffused within the AZO film produce poor crystallinity. The slight decreases in zinc and aluminum in the thin film causes a carrier concentration change, which affect the AZO film optoelectronic properties.     

The effect of hydrogen as an additive in reactive ion etching of GaAs for obtaining polished surface

The effect of hydrogen on the reactive ion etching (RIE) of GaAs in the CF₂Cl₂ plasma is discussed. The addition of hydrogen into the reaction mixture improves the sharpness of etch borders; the etched surface is smooth for etching depth > 1 μm, etching rate is time-constant.