Segmental orientations and deformation mechanism of a poly(ether‐block‐amide) film

Simultaneous measurements of microscopic infrared dichroism, mesoscale deformation, and macroscopic stress have been made for a microphase‐separated film of poly(ether‐block‐amide) 4033 during uniaxial stretching at temperatures between 30 and 91 °C, well below the melting point of the hard polyamide‐12 (PA) domains. Before the onset of dramatic microstructural alterations, the true stress–strain relationship on the mesoscale can be described with an interpenetrating network model, and poly(tetramethylene oxide) (PTMO) soft segments undergo affine deformation. Beyond a threshold strain at which stress from the soft network becomes larger than that from the hard network, plastic deformation occurs in the hard PA domains, and this is accompanied by the downward derivations of the true stress and molecular orientation of PTMO blocks from the model predictions. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 1161–1167, 2005     

Strain hardening in glassy polymers: Influence of network density on elastic and viscous contributions

In this study, the rate‐ and temperature‐dependent strain hardening and the Bauschinger effect is studied for three glassy polymers. It appeared that for all materials, an equal distribution of elastic and viscous hardening was necessary to accurately predict the Bauschinger effect, as well as the rate‐ and temperature‐dependent strain hardening response. As for the elastic contribution, the viscous contribution appears to increase with an increase in entanglement network density. Investigating the effect of temperature on the Bauschinger effect revealed that at elevated temperatures the model predictions are not accurately enough. It is shown that this is caused by the magnitude of the elastic hardening contribution; to improve the predictions, a temperature‐dependent elastic contribution is necessary. © 2019 The Authors. Journal of Polymer Science Part B: Polymer Physics published by Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019, 57, 1001–1013     

Self‐recovery and fatigue of double‐network gels with permanent and reversible bonds

Double‐network (DN) gels subjected to cyclic deformation (stretching up to a fixed strain followed by retraction down to the zero stress) demonstrate a monotonic decrease in strain with time (self‐recovery). Observations show that the duration of total recovery varies in a wide interval (from a few minutes to several days depending on composition of the gel), and this time is strongly affected by deformation history. A model is developed for the kinetics of self‐recovery. Its ability to describe stress–strain diagrams in cyclic tests with various periods of recovery is confirmed by comparison with observations on several DN gels. Numerical simulation reveals pronounced enhancement of fatigue resistance in multi‐cycle tests with stress‐ and strain‐controlled programs when subsequent cycles of deformation are interrupted by intervals of recovery. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 438–453     

Effect of solvent–matrix interactions on structures and mechanical properties of micelle‐crosslinked gels

Previous studies on hydrogels crosslinked by acrylated PEO₉₉–PPO₆₅–PEO₉₉ triblock copolymer (F127DA) micelles demonstrate outstanding strength and toughness, which is attributed to the efficient energy dissipation through the hydrophobic association in the micelles. The current study further focuses on how the solvent property affects the structures and the mechanical properties of F127DA micelle crosslinked polyacrylamide gels. Binary solvents comprised of dimethyl sulfoxide (DMSO) and water are used to adjust the polymer/solvent interactions, which consequently tune the conformations of the polymer chains in the network. The presence of DMSO significantly decreases the strength but increased the stretchability of the gels, whereas the overall tensile toughness remained unchanged. In situ small‐angle X‐ray scattering measurements reveal the deformation of micelles along with the stretching direction. A structure evolution mechanism upon solvent change is proposed, according to the experimental observations, to explain influence of solvent quality on the mechanical properties of the micelle‐crosslinked gels. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 473–483     

Wide‐angle X‐ray scattering study of the lamellar/fibrillar transition for a semi‐crystalline polymer deformed in tension in relation with the evolution of volume strain

This work is devoted to the study of the deformation mechanisms of a high‐density polyethylene deformed in tension. Specific treatments were applied to synchrotron wide‐angle X‐ray scattering patterns obtained in situ with the aim of quantifying: (i) the evolution of the apparent crystal sizes during the deformation process, (ii) the reorientation dynamics of the fragmented crystals while aligning their chains along the drawing axis during the establishment of the fibrillar morphology, and (iii) the reorientation dynamics of the amorphous chains. In addition, the volume strain evolution was measured using 3D digital image correlation. The cavitation phenomenon was found to mainly occur during the lamellae fragmentation phase. At the end of the deformation process, when the lamellar structure is destroyed, the fragmented crystals have new degrees of freedom and become free to rotate to align their chains along the drawing axis. Crystal fragmentation is then no longer needed to allow material deformation, and there is no further volume strain increase. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 1470–1480     

Microstructure evolution during tensile loading histories of a polyurea

The evolution in the hard/soft domain microstructure of an elastomeric‐like polyurea during different tensile loading histories was studied using in situ small‐ and wide‐angle X‐ray scattering (SAXS/WAXS). The nonlinear stress–strain behavior is initially stiff with a rollover yield to a more compliant response; unloading is highly nonlinear showing substantial hysteresis while also exhibiting significant recovery. Reloading reveals a substantially more compliant “softened” behavior and dramatically reduced hysteresis. WAXS peaks monitor characteristic dimensions of regular features within the hard domains; the peak location remains unchanged with tensile deformation indicating no separation of the internal structure within a domain, but the peak intensity becomes anisotropic with deformation evolving in a reversible manner consistent with orientation due to stretch. The SAXS profiles provide information between major hard domains. SAXS peaks are found to shift with tensile loading in a relatively affine manner up to a tensile true strain of ～0.4, which, using a Bragg reduction to aid interpretation, reveals an axial increase and a transverse decrease in interdomain spacings; this evolution is reversible for strains less than ～0.4. Increasing axial strain beyond a true strain of ～0.4 is accompanied by a dramatic, progressive, and irreversible reduction in axial Bragg spacing, indicating a breakdown in the hard domain aggregate network structure. A four‐point pattern is seen to develop during stretching. The breakdown in networked structure during a first load cycle gives a new structure for subsequent load cycles, which is seen to evolve in a reversible manner for strains less than or equal to the prior maximum strain. However, for strains exceeding the prior maximum strain excursion, additional breakdown is found. These SAXS results show that a breakdown in the hard domain aggregate network structure is a governing mechanism for the large dissipation (hysteresis) loops of the first load cycle and are also responsible for the softened reloading response. The absence of structure breakdown during subsequent load cycles corresponds to the substantially reduced hysteresis loops as well as the stable softened behavior. DMA data on pristine and previously deformed samples show a more compliant storage modulus in the predeformed sample, supporting the softened cyclic stress–strain data and the structural breakdown observed in the SAXS; the loss modulus was unchanged with deformation, which correlates with the lossy features measured in DMA with time‐dependent viscosity rather than losses due to structural breakdown. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

Structure and properties of segmented poly(urethaneurea)s with relatively short hard‐segment chains

We report the structure and properties of segmented poly(urethaneurea) (SPUU) with relatively short hard‐segment chains. The SPUU samples comprised poly(tetramethylene glycol) prepolymer as a soft segment and 4,4′‐diphenylmethane diisocyanate (MDI) units as a hard segment that were extended with ethylenediamine. To discuss quantitatively the conformation of the soft‐segment chain in the microphase‐separated domain space, we used SPUU samples for which the molecular weights of the hard‐ and soft‐segment chains are well characterized. The effects of the cohesive force in the hard‐segment chains on the structure and properties of SPUU were also studied with samples of different chain lengths of the hard segment, although the window of x_H, the average number of MDI units in a hard‐segment chain, was narrow (2.38 ≤ x_H ≤ 2.77). There were urethane groups in the soft segments and urea groups in the hard segments. Because of a strong cohesive force between the urea groups, we could control the overall cohesive force in the hard‐segment chains by controlling the chain lengths of the hard segment. First of all, microphase separation was found to be better developed in the samples with longer hard‐segment chains because of an increase of the cohesive force. It was also found that the interfacial thickness became thinner. The long spacing for the one‐dimensionally repeating hard‐ and soft‐segment domains could be well correlated with the molecular characteristics when the assumption of Gaussian conformation was employed for the soft‐segment chains. This is unusual for strongly segregated block copolymers and might be characteristic of multiblock copolymers containing rod–coil chains. The tensile moduli and thermal stability temperature, T_H, increased with an increase of the cohesive force, whereas the glass‐transition temperature, the melting temperature, and the degree of crystallinity of the soft‐segment chains decreased. The increase in T_H especially was appreciable, although the variation in the chain length of the hard segment was not profound. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 1716–1728, 2000     

Effect of chain entanglements on plastic deformation behavior of ultra‐high molecular weight polyethylene

Samples of ultra‐high molecular weight polyethylene, in which the chain topology within the amorphous component was altered using two‐stage processing, including crystallization at high pressure in the first step, were produced and their deformation behavior in the plane‐strain compression was studied. Deformation and recovery experiments demonstrated that the state of the molecular network governed by entanglement density is one of the primary parameters controlling the response of the material on the imposed strain, especially at moderate and high strains. Any change in the concentration of entanglements markedly influences the shape of the true stress–true strain curve. The strain hardening modulus decreases while the onset of strain hardening increases with a decrease of the entanglement density within the amorphous component. Density of entanglements also influences the amount of rubber‐like recoverable deformation and permanent plastic flow. In material of the reduced concentration of entanglements permanent flow appears easier and sets in earlier than in the material with a higher entanglement density, becoming a favorable deformation mechanism at moderate strains. As a result, strong strain hardening is postponed to higher strain when compared with the samples of equilibrium entanglement density. In the samples of an increased entanglement density the molecular network becomes stiffer, with a reduced ability of strain induced disentangling of chains. Consequently, there is a less permanent flow and strain hardening begins earlier than in the reference material of an unaltered chain topology. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 276–285, 2010     

Structure Evolution upon Uniaxial Drawing Skin‐ and Core‐Layers of Injection‐Molded Isotactic Polypropylene by In Situ Synchrotron X‐ray Scattering

The structure evolution of the oriented layer (skin) and unoriented layer (core) from injection‐molded isotactic polypropylene samples upon uniaxial drawing is probed by in situ synchrotron X‐ray scattering. The X‐ray data analysis approach, called “halo method”, is used to semiquantitatively identify the transformation process of crystal phase upon uniaxial drawing. The results verify the validation of the stress‐induced crystal fragmentation and recrystallization process in the deformation of the injection‐molded samples under different temperatures. Furthermore, the end of strain softening region in the engineering stress‐strain curves explicitly corresponds to the transition point from the stress‐induced crystal fragmentation to recrystallization process. Basically, the skin and core layers of the injection‐molded parts share the similar deformation mechanism as aforementioned. The stretching temperature which dramatically affects the relative strength between the entanglement‐induced tie chains and the adjacent crystalline lamellae determines the crystal structural evolution upon drawing. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2013, 51, 1618–1631     

Understanding Creep Behavior of Semicrystalline Polymer via Coarse‐Grained Modeling

Understanding the deformational and failure behaviors of thermoplastic semicrystalline polymers is crucial due to the practical usages in various engineering applications. Taking isotactic polypropylene (iPP) as a semicrystalline polymer model system, atomistically informed coarse‐grained (CG) molecular dynamics (MD) simulations are employed to investigate the creep behavior of iPP. The simulations reveal that there exists a threshold stress of about 20.0 MPa, above which the maximum strain of iPP within the simulation time span increases dramatically. From the strain‐time analysis, it is observed that the iPP exhibits an initial elastic deformation stage and a subsequent plastic stage at lower stress levels, while a three‐stage creep behavior including a third fracture stage is observed at higher stress levels. Specifically, at lower stress levels, the bonded energy increases continuously as the chains stretch steadily, while the nonbonded energy shows an initial increase followed by a steady decrease due to the interchain sliding. At higher stress levels, both bonded and nonbonded energies change dramatically at the third stage, resulting from accelerated chain stretching, unfolding, sliding, and breaking. This study provides physical insight into the creep behavior of iPP at a fundamental molecular level and highlights the important role of microstructural evolution of chains in the deformation of semicrystalline polymer materials. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 1779–1791     

Rheological properties of linear and crosslinked polymer blends: Relation between crosslink density and enhancement of elongational viscosity

Strain‐hardening behavior in the elongational viscosity of binary blends composed of a linear polymer and a crosslinked polymer, in which the molecular chains of the linear polymer were incorporated into the network chains of the crosslinked polymer, was studied. Blending the crosslinked polymer characterized as the gel just beyond the sol–gel transition point greatly enhanced the strain‐hardening behavior in the elongational viscosity, even though the amount of the crosslinked polymer was only 0.3 wt %. However, the crosslinked polymer, which was far beyond or below the sol–gel transition point, had little influence on the elongational viscosity as well as the shear viscosity. The stretching of the chain sections between the crosslink points was responsible for the strain‐hardening behavior. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 39: 228–235, 2001     

Strain stiffening and negative normal stress in alginate hydrogels

Alginate hydrogels are polysaccharide biopolymer networks widely useful in biomedical and food applications. Here, we report nonlinear mechanical responses of ionically crosslinked alginate hydrogels captured using large amplitude oscillatory shear experiments. Gelation was performed in situ in a rheometer and the rheological investigations on these samples captured the strain‐stiffening behavior for these gels as a function of oscillatory strain. In addition, negative normal stress was observed, which has not been reported earlier for any polysaccharide networks. The magnitude of negative normal stress increases with the applied strain amplitude and can exceed that of the shear stress at large‐strain. Fitting a constitutive relationship to the stress‐strain curves reveals that the mode of deformation involves stretching of the alginate chains and bending of both the chains and the junction zones. The contribution of bending increases near saturation of G blocks as Ca²⁺ concentration was increased. The results presented here provide an improved understanding of the deformation behavior of alginate hydrogels and such understanding can be extended to other crosslinked polysaccharide networks. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 1767–1775     

Preparation of polyhedral oligomeric silsesquioxane‐containing block copolymer with well‐controlled stereoregularity

Preparation of functional domains with a spacing of 10 nm is a benchmark set to fabricate next‐generation electronic devices. Organic–inorganic block copolymers form well‐ordered microphase separations with very small domain sizes. The design and preparation of a novel block copolymer consisting of syndiotactic polymethyl methacrylate (st‐PMMA) and polyhedral oligomeric silsesquioxane (POSS)‐functionalized polymethacrylate, designated as st‐PMMA‐b‐PMAPOSS, which can recognize functional molecules, are reported. The st‐PMMA segments form a helical structure and encapsulate C₆₀ in the helical nanocavity, leading to the formation of an inclusion complex. Although the ordering of the domains is not high, C₆₀ domains that are in a quasi‐equilibrium state, with about 10‐nm domain spacings, are generated using st‐PMMA‐b‐PMAPOSS that can recognize functional molecules. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019, 57, 2181–2189     

Relationship of deformation behavior to thermal transitions of ethylene/styrene and ethylene/octene copolymers

The stress‐strain response of low‐crystallinity ethylene‐octene (EO) and ethylene‐styrene (ES) copolymers with 7–20 mol % comonomer was compared over a temperature range that spanned the glass‐transition and crystal melting regions. Above the onset temperature of the glass transition, the copolymers exhibited elastomeric behavior with low initial modulus, uniform deformation to high strains, and high recovery after the stress was released. In the glass‐transition range, an initial low‐stress elastomeric response was followed by a distinct “bump” in the stress‐strain curve. On the basis of the temperature and rate dependence of the stress‐strain curve, local strain‐rate measurements, local temperature changes, and recovery characteristics, the “bump” was identified as high strain yielding. Hence, the stress‐strain curve sequentially exhibited the features of elastomeric and plastic deformation. Following high strain yielding, strain hardening dramatically increased the fracture strength. This behavior was defined as elastomeric‐plastic. Elastomeric‐plastic behavior in the broad glass‐transition range constituted a gradual transition from elastomeric behavior at higher temperatures to low‐temperature plastic behavior with high modulus and macroscopic necking. Because of the lower glass‐transition temperature of EO, ?40 °C as compared with ?10 °C for ES, the onset of elastomeric‐plastic behavior occurred at a significantly lower temperature. The concept of a network of flexible chains with fringed micellar crystals serving as the multifunctional junctions that provides the structural basis for elastomeric behavior of low‐crystallinity ethylene copolymers was extended to elastomeric‐plastic behavior by considering a network with a fraction of rigid, glassy chains. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 40: 142–152, 2002     

Synthesis of hydroxyl‐bearing polyurethanes from naturally occurring myo‐inositol

A route from naturally occurring myo‐inositol to hydroxyl‐bearing polyurethanes has been developed. The diol prepared from the bis‐acetalization of myo‐inositol with 1,1‐dimethoxycyclohexane was reacted with a rigid diisocyanate, 1,3‐bis(isocyanatomethyl)cyclohexane to afford the corresponding polyurethane, of which glass transition temperature (T_g) was quite high as 192 °C. The polyurethane contains side chains inherited from the acetal moieties of the diol monomer and was treated with trifluoroacetic acid to hydrolyze the acetal moieties and afford the target polyurethane functionalized with hydroxyl groups. The presence of many hydroxyl groups in the side chains, which can form hydrogen bonds with each other, resulted in a high T_g, 186 °C. In addition, the hydroxyl groups were reacted with isocyanates to achieve further side‐chain modifications. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019, 57, 1358–1364     

Structural and morphological studies on the deformation behavior of polypropylene/multi‐walled carbon nanotubes nanocomposites prepared through ultrasound‐assisted melt extrusion process

Structural and morphological behavior under stress–strain of polypropylene/multi‐walled carbon nanotubes (PP/MWCNTs) nanocomposites prepared through ultrasound‐assisted melt extrusion process was studied by means of optical microscopy, scanning electron microscopy, transmission electron microscopy, Raman spectroscopy, small angle X‐ray scattering (SAXS), and wide angle X‐ray scattering (WAXS). A high ductile behavior was observed in the PP/MWCNT nanocomposites with low concentration of MWCNTs. This was related to an energy‐dissipating mechanism, achieved by the formation of an ordered PP‐CNTs interphase zone and crystal oriented structure in the undeformed samples. Different strain‐induced‐phase transformations were observed by ex situ SAXS/WAXS, characterizing the different stages of structure development during the deformation of PP and PP/MWCNTs nanocomposites. The high concentration of CNTs reduced the strain behavior of PP due to the agglomeration of nanoparticles. A structural pathway relating the deformation‐induced phase transitions and the dissipation energy mechanism in the PP/MWCNTs nanocomposites at low concentration of nanoparticles was proposed. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 475–491     

Surface‐initiated single‐electron transfer reversible addition–fragmentation chain transfer polymerization of 2‐hydroxyethyl acrylamide on silicon substrate at ambient temperature

2‐Hydroxyethyl acrylamide was successfully polymerized via single‐electron transfer initiation on the silicon surface and propagation through the reversible addition–fragmentation chain transfer (SET‐RAFT) polymerization at ambient temperature for different polymerization times. This work is the first time application of the surface‐initiated SET‐RAFT mechanism to afford the preparation of well‐defined poly(2‐hydroxyethyl acrylamide) [poly(HEAAm)] brushes at ambient temperature. The polymerization was well controlled and produced poly(HEAAm) brushes on the silicon surface with a well‐defined target molecular weight. The controlled nature of the polymerization was further demonstrated in the presence of sulfur atoms at the chain ends in X‐ray photoelectron spectroscopy experiments. The grafting density (σ, chains nm^?2) and the average distance between grafting points (D, nm) were found to be 0.42 chains nm^?2 and 1.74 nm, respectively, indicating moderate grafting density. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 , 57, 1140–1146     

Structural developments in synthetic rubbers during uniaxial deformation by in situ synchrotron X‐ray diffraction

The molecular orientation and strain‐induced crystallization of synthetic rubbers—polyisoprene rubber, polybutadiene rubber, and butyl rubber [poly(isobutylene isoprene)]—during uniaxial deformation were studied with in situ synchrotron wide‐angle X‐ray diffraction. The high intensity of the synchrotron X‐rays and the new data analysis method made it possible to estimate the mass fractions of the strain‐induced crystals and amorphous chain segments in both the oriented and unoriented states. Contrary to the conventional concept, the majority of the molecules (50–75%) remained in an unoriented amorphous state at high strains. Each synthetic rubber showed a different behavior of strain‐induced crystallization and molecular orientation during extension and retraction. Our results confirmed the occurence of strain‐induced networks in the synthetic rubbers due to the inhomogeneity of the crosslink distribution. The strain‐induced networks containing microfibrillar crystals and oriented amorphous tie chains were responsible for the ultimate mechanical properties. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 956–964, 2004     

Effects of graded porous structure on local strain distribution under compression in silicone rubber

Silicone rubber samples with gradually changing pore sizes within the range of 70–610 μm are produced using an improved spacer method. The samples are scanned using an X‐ray computed tomography to evaluate their graded structure as compared to uniform rubber. A compressive test reveals that graded porous silicone rubber has characteristic stress–strain curves whose slope changes within a specific strain range depending on the porous structure. Analysis results of local strain based on a digital image correlation of the graded porous silicone rubber under compression demonstrate that the characteristic stress–strain properties are caused by shifts in the main deformation region in the graded structure. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 1033–1042     

Rheological properties and foam processability for blends of linear and crosslinked polyethylenes

The effect of blending crosslinked linear low‐density polyethylene (cLLDPE) on the rheological properties and foam processability of linear low‐density polyethylene was studied. A small addition of cLLDPE, which had a low density of crosslink points, enhanced strain‐hardening behavior in the elongational viscosity to a great degree, although it had little effect on the steady‐state shear viscosity. The enhanced strain hardening reduced heterogeneous deformation during foaming. As a result, a foam with a uniform cell size distribution was obtained. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 2159–2167, 2001