Electrochromic devices based on copolymers of 3-Trimethoxysilanylpropyl-N-aniline-2,5-Dimethoxyaniline

Electrochemical copolymerization of 3-trimethoxysilanyl-propyl-N-aniline (TMSPA) with 2,5-dimethoxyaniline (DMA) was performed in 1 M HCl aqueous solution for different feed ratios of TMSPA using cyclic voltammetry. The deposition rate of TMSPA–DMA copolymer is higher than that of PTMSPA but lower than that of PDMA. (TMSPA-co-DMA) film was deposited using electrochemical polymerization as conducting film on indium tin oxide (ITO) electrode and used as an electrode in an electrochromic device. Poly(3,4-ethylenedioxythiophene):poly(4-styrenesulfonate) (PEDOT:PSS) was spin-coated on ITO as the other electrode. Carboxyl-terminated- butadiene-acrylonitrile (CTBN) blended with LiClO₄ was used as solid polymer electrolyte. A total solid electrochromic device was assembled as follows: ITO|P(TMSPA-co-DMA)LiClO₄-CTBNPEDOT:PSS|ITO. The columbic efficiency of the devices reached to 104% for P(TMSPA-co-DMA) film with TMSPA feed ratio of 0.25. The optical contrast (ΔT, %) of the single electrode and the device were determined by UV–vis spectroelectrochemical studies. The stability of ΔT was improved during color switching from +1.5 to −1.5 V (vs. PEDOT) for this device. The device was pale yellow at −1.5 V and blue at +1.5 V.     

Investigation of the doping efficiency of poly(styrene sulfonic acid) in poly(3,4‐ethylenedioxythiophene)/poly(styrene sulfonic acid) dispersions by capillary electrophoresis

CE can efficiently separate poly(3,4‐ethylenedioxythiophene)/poly(styrene sulfonic acid) (PEDOT/PSS) complexes and free PSS in dispersions and can be used to estimate the degree of PSS doping. We investigated the doping efficiency of PSS on PEDOT in dispersions using CE and its effect on the conductivity of the resulting PEDOT/PSS films. Results of this study indicate that dispersions containing 1:2.5–3 EDOT:PSS feed ratio (by weight) exhibiting 72–73% PSS doping generate highly processable and highly conductive films. Conductivity can be optimized by limiting the time of reaction to 12 h. At this point of the reaction, the PEDOT/PSS segments, appearing as broad band in the electropherogram, could still exist in an extended coil conformation favoring charge transport resulting in high conductivity. Above a threshold PEDOT length formed at reaction times longer than 12 h, the PEDOT/PSS complex, appearing as spikes in the electropherogram, most likely have undergone a conformational change to coiled core‐shell structure restricting charge transport resulting in low conductivity. The optimal conductivity (5.2 S/cm) of films from dispersions synthesized for 12 h is significantly higher than those from its commercial equivalent Clevios P and other reported values obtained under similar conditions without the addition of codopants.     

A new green-to-transmissive polymer with electroactive poly(3,4-ethylene dioxythiophene):poly(styrene sulfonate) as an interface layer for achieving high-performance electrochromic device

A new neutral green electrochromic (EC) polymer, namely poly(5,8-bis(2,3-dihydro[3,4-B][1,4]dioxin-5-yl)-2,3-dual(4-(hexadecyloxy) phenyl) quinoxaline) (PBOPEQ) was designed and synthesized. PBOPEQ-poly(3,4-ethylene dioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) film was further prepared by electrochemical polymerization on the PEDOT:PSS modified indium tin oxide (ITO) electrode. Scanning electron microscopy images and ultrasonic experiment indicate that PBOPEQ-PEDOT:PSS film shows better film-forming ability and stronger interface adhesive with ITO electrode compared to that of PBOPEQ film. It is worth mentioning that PBOPEQ-PEDOT:PSS film presents more reversible redox characteristic, better optical contrast (~40%) and coloration efficiency (~230 cm² C⁻¹) at 678 nm, excellent EC stability and memory property (36 hr), which should be ascribed to that the electroactive PEDOT:PSS layer facilitates the charge transfer process and enhances the ion doping/dedoping properties. EC device based on PBOPEQ-PEDOT:PSS film exhibits superior integrated performance such as reversible color change from green to transmissive, optical contrast of 41.0% and switching time less than 1 s. Accordingly, PBOPEQ-PEDOT:PSS is an excellent EC material when combined with electroactive PEDOT:PSS interface layer for achieving high performance device, which shows potential applications in displays, electronic papers, and tags.     

Applications of poly(3,4-ethylenedioxythiophene) doped with poly(styrene sulfonic acid) transistors in chemical and biological sensors

The application of transistors based on poly(3,4-ethylenedioxythiophene) doped with poly(styrene sulfonic acid) (PEDOT:PSS) in chemical and biological sensing is reviewed. These devices offer enormous potential for facile processing of small, portable, and inexpensive sensors ideally suited for point-of-care analysis. They can be used to detect a wide range of analytes for a variety of possible applications in fields such as health care (medical diagnostics), environmental monitoring (airborne chemicals, water contamination, etc.), and food industry (smart packaging). Organic transistors are excellent candidates to act as transducers because they have the ability to translate chemical and biological signals into electronic signals with high sensitivity. Furthermore, fuctionalization of PEDOT:PSS films with a chemical or biological receptor can lead to high specificity. The advantages of using PEDOT:PSS transistors are described, and applications are presented for sensing analytes in both gaseous and aqueous environments.     

Poly(thieno[3,4‐b]‐1,4‐oxathiane) and poly(3,4‐ethylenedioxythiophene‐co‐thieno[3,4‐b]‐1,4‐oxathiane)/poly(styrene sulfonic sodium): Preparation,characterization, and optoelectronic performance

In this work, the asymmetrical analog of 3,4‐ethylenedioxythiophene (EDOT), thieno[3,4‐b]‐1,4‐oxathiane (EOTT), was synthesized and chemically polymerized first in aqueous solution using poly(styrene sulfonic sodium) (PSS) as the polyelectrolyte to yield poly(thieno[3,4‐b]‐1,4‐oxathiane) (PEOTT)/PSS. As‐formed film exhibited low electrical conductivity (～10^?4 S/cm). Alternatively, EOTT together with EDOT (in different molar ratio of 1:1 and 1:5) was copolymerized and the polymer poly(EOTT‐co‐EDOT)/PSS had electrical conductivity of 10^?1 S/cm. After dimethyl sulfoxide (DMSO) treatment, the electrical conductivity was enhanced to 10⁰ S/cm; however, the conductivity of the above homopolymer was reduced (～10^?5 S/cm). Raman spectroscopy was used to interpret conductivity enhancement or reduction after DMSO treatment. The conductivity decrease of PEOTT/PSS compared to poly(EOTT‐co‐EDOT)/PSS may arise from the conformational change of PEOTT backbone from the quasi‐planar to the distorted planar mode induced by PSS^–/PSSH through ionic interaction. Kinetic studies revealed that the copolymer had high coloration efficiencies (375 cm²/C), low switching voltages (?0.8 to +0.6 V), decent contrast ratios (45%), moderate response time (1.0 s), excellent stability, and color persistence. An electrochromic device employing poly(3‐methylthiophene) and poly(EOTT‐co‐EDOT)/PSS as the anode and cathode materials was also studied. From these results, poly(EOTT‐co‐EDOT)/PSS would be a promising candidate material for organic electronics. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 2285–2297     

Simultaneous synthesis of silver nanoparticles and poly(2,5‐dimethoxyaniline) in poly(styrene sulfonic acid)

Silver nanoparticles were formed in situ along with poly(2,5‐dimethoxyaniline) (PDMA) in an interconnected network matrix (reactor), comprising the electronic conductive polymer, PDMA, and a polyelectrolyte, poly(styrene sulfonic acid) (PSS), through the simultaneous reduction of Ag⁺ ions and polymerization of 2,5‐dimethoxyaniline. In situ ultraviolet‐visible spectroscopy showed that peaks corresponding to the plasmon resonance of silver nanoparticles at 411 nm and the polaronic transition of PDMA at 438 nm provided evidences for the simultaneous formation of silver nanoparticles and PDMA. Transmission electron microscopy and size distribution analysis revealed the presence of spherical silver nanoparticles with an average diameter of 12 nm in the composite. X‐ray photoelectron spectroscopy showed that the amine units in PDMA changed to imine units upon the formation of silver nanoparticles. A comprehensive mechanism for the formation of the PDMA‐PSS‐Ag nanocomposite is proposed. A 10‐fold increase in the conductivity was noticed for the PDMA–PSS–Ag nanocomposite (1 S/cm) in comparison with the PDMA–PSS composite (0.1 S/cm). © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3843–3852, 2006     

Preparation and characterization of a poly(vinylbenzyl sulfonic acid)‐grafted FEP membrane

In this study, a novel polymer electrolyte membrane, poly(vinylbenzyl sulfonic acid)‐grafted poly(tetrafluoroethylene‐co‐hexafluoropropylene) (FEP‐g‐PVBSA), has been successfully prepared by simultaneous irradiation grafting of vinylbenzyl chloride (VBC) monomer onto a FEP film and taking subsequent chemical modification steps to modify the benzyl chloride moiety to the benzyl sulfonic acid moiety. The chemical reactions for the sulfonation were carried out via the formation of thiouronium salt with thiourea, base‐catalyzed hydrolysis for the formation of thiol, and oxidation with hydrogen peroxide. Each chemical conversion process was confirmed by FTIR, elemental analysis, and SEM‐EDX. A chemical stability study performed with Fenton's reagent (3% H₂O₂ solution containing 4 ppm of Fe²⁺) at 70 °C revealed that FEP‐g‐PVBSA has a higher chemical stability than the poly(styrene sulfonic acid)‐grafted membranes (FEP‐g‐PSSA). © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 563–569, 2010     

Poly(styrene sulfonic acid)–poly(vinylidene fluoride) interpolymer ion-exchange membranes. II. Ultrafiltration properties

Highly porous interpolymer ion-exchange membranes of poly(styrene sulfonic acid) and poly(vinylidene fluoride) have been investigated under pressure filtration with KCI, Na₂SO₄, erythrosin, and bovine serum albumin as solutes in the feed solution. The rejection of the ionic solutes is governed by a Donnan exclusion of electrolyte from the membrane phase. A model for the transport behavior is proposed that includes both diffusive and convective salt transport. The calculated rejections agree adequately with the observed data.     

Conductivity enhancement of PEDOT:PSS film via sulfonic acid modification: application as transparent electrode for ITO-free polymer solar cells

3-Hydroxy-1-propanesulfonic acid(HPSA)was applied as a modification layer on poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate)(PEDOT:PSS)film via spin-coating,resulting in a massive boost of the conductivity of PEDOT:PSS film,and thus the as-formed PEDOT:PSS/HPSA bilayer film was successfully used as a transparent electrode for ITO-free polymer solar cells(PSCs).Under the optimized concentration of HPSA(0.2 mol L~(-1)),the PEDOT:PSS/HPSA bilayer film has a conductivity of 1020 S cm~(-1),which is improved by about 1400 times of the pristine PEDOT:PSS film(0.7 S cm~(-1)).The sheet resistance of the PEDOT:PSS/HPSA bilayer film was 98Ωsq~(-1),and its transparency in the visible range was over 80%.Both parameters are comparable to those of ITO,enabling its suitability as the transparent electrode.According to atomic force microscopy(AFM),UV-Vis and Raman spectroscopic measurements,the conductivity enhancement was resulted from the removal of PSS moiety by methanol solvent and HPSA-induced segregation of insulating PSS chains along with the conformation transition of the conductive PEDOT chains within PEDOT:PSS.Upon applying PEDOT:PSS/HPSA bilayer film as the transparent electrode substituting ITO,the ITO-free polymer solar cells(PSCs)based on poly[N-9″-hepta-decanyl-2,7-carbazole-alt-5,5-(4′,7′-di-2-thienyl-2′,1′,3′-benzothiadiazole)]:[6,6]-phenyl C71-butyric acid methyl ester(PC_(71)BM)(PCDTBT:PC_(71)BM)active layer exhibited a power conversion efficiency(PCE)of 5.52%,which is comparable to that of the traditional ITO-based devices.     

Plasma Modified V2O5/PEDOT Hybrid Based Flexible Electrochromic Devices

Vanadium oxide/poly (3,4‐ ethylenedioxythiophene)(V₂O₅‐PEDOT) hybrid materials were prepared in a rotating quartz plasma reactor via capacitively coupled radio frequency (RF 13.56 MHz) plasma. Thin films of V₂O₅‐PEDOT hybrid and V₂O₅ were obtained by electron beam evaporation technique onto flexible PET substrate for electrochromic devices (ECDs) applications. As a counter electrode, both RF magnetron sputtered MoO₃ onto ITO coated PET and only ITO coated PET electrodes were used. Characterizations of the films were carried out via using scanning electron microscopy‐energy dispersive X‐ray spectroscopy (SEM‐EDX) and X‐ray diffraction (XRD). Hybrid ECDs results showed that synergistic effect depending on improved stability between V₂O₅ and PEDOT. As a result, we developed all solid complementary electrochromic devices including V₂O₅, V₂O₅‐PEDOT and MoO₃ films. The electrochromic device characteristics such as electrochromic contrast, coloration efficiency, switching time were calculated from optical and electrochemical measurements. The highest coloration efficiency and optical contrast were obtained as 53 cm²/C and 17 % for V₂O₅‐PEDOT/MoO₃‐based ECD.     

Nanofiltration membranes based on poly(vinylidene fluoride‐co‐chlorotrifluoroethylene)‐graft‐poly(styrene sulfonic acid)

Graft copolymers comprising poly(vinylidene fluoride‐co‐chlorotrifluoroethylene) backbone and poly(styrene sulfonic acid) side chains, i.e. P(VDF‐co‐CTFE)‐g‐PSSA were synthesized using atom transfer radical polymerization (ATRP) for composite nanofiltration (NF) membranes. Direct initiation of the secondary chlorinated site of CTFE units facilitates grafting of PSSA, as revealed by FT‐IR spectroscopy. The successful “grafting from” method and the microphase‐separated structure of the graft copolymer were confirmed by transmission electron microscopy (TEM). Wide angle X‐ray scattering (WAXS) also showed the decrease in the crystallinity of P(VDF‐co‐CTFE) upon graft copolymerization. Composite NF membranes were prepared from P(VDF‐co‐CTFE)‐g‐PSSA as a top layer coated onto P(VDF‐co‐CTFE) ultrafiltration support membrane. Both the rejections and the flux of composite membranes increased with increasing PSSA concentration due to the increase in SO₃H groups and membrane hydrophilicity, as supported by contact angle measurement. The rejections of NF membranes containing 47 wt% of PSSA were 83% for Na₂SO₄ and 28% for NaCl, and the solution flux were 18 and 32 L/m² hr, respectively, at 0.3 MPa pressure. Copyright © 2008 John Wiley & Sons, Ltd.     

A novel high‐contrast ratio electrochromic material from spiro[cyclododecane‐1,9′‐fluorene]bicarbazole

A novel electroactive spirocyclododecylfluorene monomer named 2,7‐bis(carbazol‐9‐yl)‐9,9′‐spiro[cyclododecane‐1,9′‐fluorene] (SFC) was synthesized and electrochemically polymerized to give a very stable multi‐electrochromic polymer (poly‐SFC). Two separate oxidation processes were observed for both SFC monomer and poly‐SFC that carries two carbazole units. The polymeric film of poly‐SFC was coated onto ITO/glass surface, and it shows different colors (transparent, yellowish green, green, and dark green) upon stepwise oxidations. An electrochromic device based on poly‐SFC was assembled in the sandwich cell configuration of ITO/poly‐SFC//gel electrolyte//PEDOT/ITO. Poly‐SFC exhibits 90% of transparency at neutral state and a high contrast ratio (ΔT = 58% at 800 nm). This device constructed from it represents a response time of about 1 s, high coloration efficiency (1377 cm² C^–1) and retained its performance by 96.4% even after 1000 cycles. Exhibiting high transparency at neutral state, reversible redox behavior, resistance to overoxidation, and especially high contrast ratio at near IR region can make poly‐SFC be useful and promising candidate for electrochromic applications despite having a relatively slow response time. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2010     

Random poly(fluorenylene‐vinylene)s containing 3,7‐Dibenzothiophene‐5,5‐dioxide units: Synthesis,photophysical, and electroluminescence properties

The synthesis of new random poly(arylene‐vinylene)s containing the electron withdrawing 3,7‐dibenzothiophene‐5,5‐dioxide unit was achieved by the Suzuki–Heck cascade polymerization reaction. The properties of poly[9,9‐bis(2‐ethylhexyl)‐2,7‐fluorenylene‐vinylene‐co‐3,7‐dibenzothiophene‐5,5‐dioxide‐vinylene] (50/50 mol/mol, P1 ) and poly[1,4‐bis(2‐ethylhexyloxy)‐2,5‐phenylene‐vinylene‐co‐3,7‐dibenzothiophene‐5,5‐dioxide‐vinylene] (50/50 mol/mol, P2 ) were compared with those of terpolymers obtained by combining the fluorene, dibenzothiophene, and 1,4‐bis(2‐ethylexyloxy)benzene in 20/40/40 ( P3 ), 50/25/25 ( P4 ), and 80/10/10 ( P5 ) molar ratios. The polymers were characterized by ¹H NMR and IR, whereas their thermal properties were investigated by TGA and DSC. Polymers P1–5 are blue–green emitters in solution (λ_em between 481 and 521 nm) whereas a profound red shift observed in the solid state is emission (λ_em from 578 to 608 nm) that can be attributed both to the charge transfer stabilization exerted by the polar medium and to intermolecular interactions occurring in the solid state. Cyclic voltammetry permitted the evaluation of the ionization potentials and also revealed a quasi‐reversible behavior in the reduction scans for the polymers ( P1–4 ) containing the higher amounts of 3,7‐dibenzothiophene‐5,5‐dioxide units. Electroluminescent devices with both ITO/PEDOT‐PSS/ P1–5 /Ca/Al (Type I) and ITO/PEDOT‐PSS/ P1–5 /Alq₃/Ca/Al (Type II) configuration were fabricated showing a yellow to yellow–green emission. In the case of P4 , a luminance of 1835 cd/m² and an efficiency of 0.25 cd/A at 14 V were obtained for the Type II devices. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 2093–2104, 2009     

Novel electroluminescent cationic polyelectrolyte based on poly[(fluorene‐2,7‐diylvinylene)‐alt‐(1,4‐phenylenevinylene)] and its precursor

A novel conjugated poly[(fluorene‐2,7‐vinylene)‐alt‐(1,4‐phenylenevinylene)] derivative 2 with quaternizable tertiary amino groups was synthesized by Heck coupling of a substituted 2,7‐dibromofluorene and 1,4‐dialkoxy‐2,5‐divinylbenzene. The corresponding quaternary ammonium cationic polyelectrolyte 3 was obtained by the treatment of 2 with bromoethane. Both polymers were soluble in common organic solvents, like tetrahydrofuran, chloroform, and dichloromethane. Polymer 3 showed a limited solubility in alcohols and was insoluble in water. Photophysical and electrochemical properties of the resulting polymers were fully investigated. An intensive green photoluminescence (PL) with maxima at 550 and 545 nm was observed from thin films of 2 and 3 polymers, respectively, red‐shifted compared with the PL emission spectra measured in the solution. The electrochemical band gaps were 2.38–2.45 eV. Single‐layer and double‐layer (with poly[3,4‐(ethylenedioxy)thiophene]/poly (styrenesulfonate) (PEDOT:PSS)) light‐emitting devices (LEDs) with ITO and Al electrodes were prepared and studied. They emitted a green light and their electroluminescence (EL) spectra were similar to those of PL thin films. The external EL efficiency was determined to be 0.43 and 0.32% for ITO/PEDOT:PSS/ 2 /Al and ITO/PEDOT:PSS/ 3 /Al LEDs, respectively. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 1016–1027, 2007     

GelatinnZn(CF3SO3)2 Polymer Electrolytes for Electrochromic Devices

The present work is focused on gelatin‐based electrolytes doped with a range of concentration of zinc triflate (Zn(CF₃SO₃)₂). The transparent‐thin‐film samples have been represented by the notation Gelatin_nZn(CF₃SO₃)₂, where n represents the zinc triflate salt concentration in the electrolyte membranes from 0.00 wt% to 10.93 wt% . The samples have been characterized by conductivity measurements, thermal analysis, cyclic voltammetry, X‐ray diffraction (XRD), polarized optical microscopy (POM) and scanning electron microscopy (SEM). The gelatin‐based electrolytes were also tested as ionic conductors in electrochromic devices with the glass/ITO/WO₃/gelatin‐based electrolyte/CeO₂‐TiO₂/ITO/glass configuration.     

High‐performance Flexible Complementary Electrochromic Device Based on Plasma Modified WO3 Nano Hybrids and V2O5 Nanofilm with Low Operation Voltages

Tungsten trioxide‐poly(3,4‐ethylenedioxythiophene) (WO₃‐PEDOT) and tungsten trioxide‐polyfuran (WO₃‐PFu) were prepared by rf rotating plasma polymerization. Electrochromic hybrid thin films were fabricated onto flexible polyethylene terephthalate (PET)/ indium tin oxide (ITO) film using electron beam evaporation method. In order to deeply characterize all films, scanning electron microscopy‐energy dispersive X‐ray spectroscopy (SEM‐EDS) and electrochemical impedance spectroscopy (EIS) techniques were used. The counter electrode effect on plasma modified WO₃ nano hybrids‐based electrochromic devices (ECDs) was evaluated. By incorporating flexible vanadium pentoxide (V₂O₅) film as counter electrode, complementary ECDs were constructed through combining the hybrid flexible films (WO₃‐PEDOT, WO₃‐PFu) as working electrodes, which exhibit highly efficient electrochromic performance with low voltage operation. Especially, WO₃‐PEDOT/V₂O₅‐based ECD owns a high optical modulation of 61.5 % at 750 nm driven by −1.0 V (coloration) and +1 V (bleaching) with fast response times (coloration time: 13.58 s, bleaching time: 8.07 s) and a high coloration efficiency of 527 cm² C⁻¹. This study can supply useful and efficient avenue for designing flexible complementary electrochromic device for energy‐saving flexible electronics.     

Characterization of polyether‐poly(methyl methacrylate)‐lithium perchlorate blend electrolytes

Solid polymer electrolyte (SPE) systems based on interpenetrating blends of poly(ethylene oxide‐co‐propylene oxide) and poly(methyl methacrylate) host matrices, with lithium perchlorate as guest salt, were prepared. These electrolytes were presented as free‐standing films, and their thermal and electrochemical properties were characterized by conductivity and electrochemical stability measurements. The properties of the interpenetrating blends of poly(ethylene oxide‐co‐propylene oxide) and poly(methyl methacrylate) host matrices as the electrolyte component of a solid‐state electrochromic device are reported and the results obtained suggest that this electrolyte provides an encouraging performance in this application. The most conducting electrolyte composition of this SPE system is the formulation designated as SPE2‐0PC (5.01 × 10^?4 S cm^?1 at about 57°C). The lowest decomposition temperature was registered with the SPE6‐15PC composition (233°C). The average transmittance in the visible region of the spectrum was above 41% for all the samples analyzed. After coloration the device assembled with 71 wt% PC presented an average transmittance of 15.71% and an optical density at 550 nm of 0.61. Copyright © 2010 John Wiley & Sons, Ltd.     

Preparation of electrically conducting cellulose fibres utilizing polyelectrolyte multilayers of poly(3,4-ethylenedioxythiophene):poly(styrene sulphonate) and poly(allyl amine)

The primary goal with this work is to create electrically conductive cellulose fibres, this has been done to explore possible new applications for fibre based material. This research uses various methods to create polyelectrolyte multilayers (PEMs) on bleached softwood fibres and on SiO₂ model surfaces, by sequentially treating these materials with poly(3,4-ethylenedioxythiophene):poly(styrene sulphonate) (PEDOT:PSS) and poly(allyl amine) (PAH). Paper sheets were then produced from the PEM-modified pulp and evaluated in terms of tensile strength, adsorbed amount of polymer, and electrical conductivity. To evaluate the influence of fibre charge on the measured paper properties, pulps of two different initial fibre charge densities were prepared via carboxymethylation. Because of the bluish colour of PEDOT:PSS, the build-up of PEM could be easily followed, since the fibres grew increasingly darker blue throughout the modification sequence. The conductivity of the fibre network increased by 2−3 orders of magnitude when the pulp of a higher fibre charge density was used. This suggests that it is more important to create a fibrous network with a high fibre-fibre joint strength and a large total joined area in the sheet rather than to maximize the adsorbed amount of PEDOT:PSS. A difference in conductivity could also be noted depending on the polyelectrolyte adsorbed in the outer layer, PAH lowered the conductivity compared to PEDOT:PSS. Evaluating the mechanical properties revealed that the use of PEDOT:PSS reduces the tensile strength of the paper. When five double layers had been adsorbed onto the carboxymethylated sample in which PEDOT:PSS formed the outer layer, calculations indicated a 25% decrease in tensile strength compared to that of reference material without PEMs. ESEM studies indicate that PEM treatment produces a significantly changed and somewhat smoother fibre surface.     

New cyanopyridine‐based π‐conjugative poly(azomethine)s: Synthesis,characterization and electroluminescence studies

Four new Schiff‐base type conjugative polymers (CPs), that is, Py _1‐4 carrying a strong electron‐withdrawing cyanopyridine scaffold coupled with different electron‐donating aromatic/heteroaromatic moieties were synthesized from their respective co‐monomers by simple poly‐condensation route. They were subjected to structural, thermal, photophysical, and electrochemical characterizations and theoretical investigations in order to identify their suitability in polymer light‐emitting diode (PLED) application. All these polymers showed good film‐forming ability and exhibited favorable photophysical behaviors with an optical bandgap in the order of 2.54‐2.68 eV. Further, their electrochemical data were used to evaluate highest occupied molecular orbital (HOMO) and lowest unoccupied molecular orbital (LUMO) levels. Finally, Py _1‐4 were successfully employed as blue‐light emitter in the construction of new ITO/PEDOT:PSS/ Py _1‐4 /Al configured light‐emitting diodes (LED), and the fabricated devices demonstrated stable blue electroluminescence behavior endorsing an effective electrons injection in the PLEDs.     

Synthesis of poly[(2‐oxo‐1,3‐dioxolane‐ 4‐yl)methyl methacrylate‐co‐styrene] by addition reaction of carbon dioxide and its compatibility with poly(methyl methacrylate) or poly(vinyl chloride)

We investigated the chemical fixation of carbon dioxide (CO ₂) to a copolymer bearing epoxide and the application of the cyclic carbonate group containing copolymer to polymer blends. In the synthesis of poly[(2‐oxo‐1,3‐dioxolane‐4‐yl)methyl methacrylate‐co‐styrene] [poly(DOMA‐co‐St)] from the addition of CO ₂ to poly(glycidyl methacrylate‐co‐styrene) [poly(GMA‐co‐St)], quaternary ammonium salts showed good catalytic activity at mild reaction conditions. The CO ₂ addition reaction followed pseudo first‐order kinetics with the concentration of poly(GMA‐co‐St). In order to expand the applications of the CO ₂ fixed copolymer, polymer blends of this copolymer with poly(methyl methacrylate) (PMMA) or poly(vinyl chloride) (PVC) were cast from N,N′‐dimethylformamide (DMF) solution. Miscibility of blends of poly(DOMA‐co‐St) with PMMA or PVC have been investigated both by differential scanning calorimetry (DSC) and visual inspection of the blends, and the blends were miscible over the whole composition ranges. The miscibility behaviors were also discussed in terms of FT‐IR spectra. Copyright © 2002 John Wiley & Sons, Ltd.