Indirect determination of free cyanide in industrial waste effluent by atomic absorption spectrometry

An indirect method is described for the determination of free cyanide in industrial waste effluent samples by atomic absorption spectrometry (AAS). In an alkaline medium, cyanide forms a stable complex species [Cu(BPTC)(CN)] (BPTC = 2-benzoylpyridine thiosemicarbazone), which can be extracted into a mixture of isobutyl methyl ketone-isopentyl alcohol (7 + 1) with an efficiency of greater than 98.5%. The extract can be analysed directly for copper (and hence indirectly for cyanide) by flame AAS. The calibration graph is linear up to 5.7 micrograms of cyanide per millilitre of solvent mixture and the limit of detection is 4.8 ng ml-1. A large number of foreign ions were found not to interfere with the proposed method.     

间接原子吸收法测定药物制剂中利血生的含量

提出了利血生的间接原子吸收法，该法基于利血生在碱性介质中的分离－产物半胱氨酸在适当的PH条件下与铜离子生成灰色沉淀，通过测定上清液中铜的含量来间接测定利血生的含量，在法在10－100mg/L范围内呈良好的线性关系（r=0.9992),回收率为98．5％－101．6％。该法可成功地用于药物制剂中利血生的测定。     

Spectrophotometric and Indirect Determination of Lincomycin by Atomic Absorption Spectroscopy (AAS)

Abstract

The reaction of lincomycin with cupric ions in alkaline medium was taken as a basis for the colorimetric and indirect atomic absorption spectrometric (AAS) determination of lincomycin hydrochloride.

The AAS procedure was based on the extraction of copper-lincomycin complex at pH 11, into n-butanol. The copper content in this extract was determined by AAS. The response was linear for up to 30 μg ml^?1 of lincomycin. The method is accurate, sensitive and simple.

The proposed methods were applied to pharmaceutical preparations with fine accuracy.     

测定微量血清铜、锌的新方法

报道了单用重蒸馏氏倍稀释微量血清后,直接采用ＰＥ４００型原子吸收仪,ＨＧＡ７００型石墨炉,测定血清中铜,锌浓度的新方法。本法用血量少,只用重蒸馏水稀释,标本不易受污染,测定结果稳定,与标准的火焰原子吸收法测定结果有很好的相关性。本法可提高微量法测定铜,锌浓度的准确性,有助于末梢血微量元素测定方法在临床的推广,尤其适用于儿科病儿及需反复测定多种元素的病人。     

Indirect atomic absorption spectrometric determination of perchlorate by liquid-liquid extraction in a flow-injection system

The determination is based on the continuous liquid-liquid extraction of the copper(I)/6-methylpicolinealdehyde azine/perchlorate ion-pair into 4-methyl-2-pentanone in a flow-injection manifold. The organic fills a loop of an injector situated in an integrated feed system of an atomic absorption spectrometer. Measurement of the copper atomic absorption signal from the organic phase allows the indirect determination of 0.5–5 μg ml^?1 perchlorate, giving a 3-fold increase in sensitivity over the conventional spectrophotometric method. The detection limit is 70 ng ml^?1. The sampling frequency is 45 ± 5 h^?1. The method is highly selective, and has been used for the determination of perchlorate added to serum and urine samples.     

Determination of trace amounts of copper(II) by using catalytic redox reaction between methylene blue and ascorbic acid.

A sensitive and selective kinetic-spectrophotometric method is proposed for the determination of microg mL(-1) amounts of Cu2+ based on its catalytic effect on the oxidation of L-ascorbic acid by Methylene Blue in a strongly acidic medium. The reaction is monitored spectrophotometrically by measuring the decrease in color intensity of Methylene Blue at 665 nm. The analysis of Cu2+ ion is performed by a fixed-time method. At a given time of 2 min at pH 2.20 and 32 degrees C, the detection limit is 10 ng mL(-1) and the relative standard deviation for 0.4 microg mL(-1) Cu2+ is 3.60% (n = 6). The method is free from most of the interferences and the effect of diverse ions on the determination of Cu2+ is also reported. The proposed method is virtually specific to copper and has been satisfactorily applied to its determination in electric copper wire samples and pharmaceutical products. Results were also verified by the atomic absorption spectrometry technique (AAS).     

Column chromatographic pre-concentration of iron(III) in alloys and biological samples with 1-nitroso-2-naphthol-3,6-disulphonate and benzyldimethyltetradecylammonium-perchlorate adsorbent supported on naphthalene using atomic absorption spectrometry

The solid ion-pair material produced from the reaction between benzyldimethyltetradecylammonium chloride (BDTA) and sodium perchlorate on naphthalene provides the basis for a simple, rapid and selective technique for pre-concentrating iron from up to 500 ml of aqueous solution. Iron reacts with disodium 1-nitroso-2-naphthol-3,6-disulphonate (Nitroso-R salt) to form a water-soluble coloured chelate anion. The iron chelate anion forms a water-insoluble, stable iron-Nitroso-R-BDTA complex on naphthalene packed in a column. Trace amounts of iron are quantitatively retained on naphthalene in the pH range 3.5-7.5 and at a flow-rate of 1-2 ml min-1. The solid mass is dissolved out from the column with 5 ml of N,N-dimethylformamide and iron is determined by means of an atomic absorption spectrometer at 248 nm. The calibration graph is linear for concentrations of iron over the range of 0.5-20 micrograms in 5 ml of final solution. The standard deviation and relative standard deviation were calculated. The detection limit of the method was 0.0196 micrograms ml-1 of iron. The sensitivity for 1% absorption was 0.072 microgram ml-1 (0.165 microgram ml-1 by direct atomic absorption spectrometry of aqueous solution). The proposed method was applied to the determination of iron in standard alloys and biological samples.     

Determination of selenium in blood plasma and serum by flow injection hydride generation atomic absorption spectrometry

A flow injection hydride generation atomic absorption spectrometric (AAS) method has been used to determine the selenium concentrations of human serum and plasma samples following digestion with nitric, sulphuric and perchloric acids. In the hydride generation process, reduction was carried out by sodium tetrahydroborate to produce a hydride that was atomized in a flame-heated atomisation cell. The method had a detection limit of 1.2 ng ml-1 and a sensitivity of 2.1 ng ml-1. Within-run precisions of 5.8% at 20 ng ml-1 and 4.5% at 80 ng ml-1, and between-run precisions of 4.8% at 69 ng ml-1 and 3.4% at 80 ng ml-1 were obtained. An inter-laboratory comparison study with a graphite furnace AAS method was carried out and the results showed excellent agreement. The flow injection method of sample introduction allowed the use of a sample volume of 330 microliters with an injection rate of 90 injections per hour.     

Rapid and simple determination of selenium in blood serum by inductively coupled plasma–mass spectrometry (ICP–MS)

An inductively coupled plasma mass spectrometer (ICP-MS) with a rapid sample-preparative procedure was used for the determination of selenium in blood serum. Blood serum was prepared by dilution in an acidic solution consisting of nitric acid (1%), X-triton (0.1%) and 1-butanol (0.8%). A calibration curve was established for 1-40 microg mL(-1) (r(2)>0.99). The limit of detection was 0.5 microg mL(-1). Repeatability and intermediate precision were satisfactory with relative standard deviations (RSD) of 2.0% and 3.2%, respectively. This method was easily applied to reference materials with satisfactory accuracy. Good correlation (r(2)=0.96) was observed between ICP-MS and atomic absorption spectrometry (AAS) for the determination of (82)Se in blood serum from 23 patients. These results suggest that the sample preparative procedure coupled with ICP-MS can be used for the routine determination of (82)Se in human blood serum.     

Ion-pair extraction and determination of copper(II) and zinc(II) in environmental and pharmaceutical samples.

Copper and zinc were extracted from salicylate solution into Aliquat 336 dissolved in toluene and determined in the organic phase spectrophotometrically using 1-(2-pyridylazo)-2-naphthol. The determination of copper and zinc was also carried out titrimetrically or by atomic absorption spectrometry after stripping the metal ions from the organic phase. The method permits the determination of copper and zinc in environmental and pharmaceutical samples. The standard deviation and relative standard deviation are 0.052 micrograms and 0.69%, respectively, for copper and 0.041 micrograms and 0.60%, respectively, for zinc.     

The cloud point extraction of copper(II) with monocarboxylic acids into non-ionic surfactant phase

The possibility to use monocarboxylic acids and their mixtures with amines for copper concentrating by the way of micellar extraction at cloud point temperature, and later atomic absorption spectrometry (AAS) determination was investigated. Under the optimum conditions, preconcentration of 100 ml of water sample in the presence of 1% non-ionic surfactant OP-10, 0.005 M capric acid and 0.01 M octylamine permitted the detection of 0.01 μg ml⁻¹ copper. The proposed method has been applied to the AAS determination of copper in water samples after cloud point extraction.     

Simultaneous determination of acetylsalicylic and salicylic acids in human serum and aspirin formulations by second-derivative synchronous fluorescence spectrometry

A second-derivative synchronous scanning spectrofluorimetric method for the simultaneous determination of acetylsalicylic acid (ASA) and salicylic acid (SA) is described. The method is based on the native fluorescence of both acids in a 1% acetic acid-chloroform solution. Both ASA and SA can be determined within the concentration ranges 0.2-70 and 0.03-10 micrograms ml-1, respectively. The effect of each acid on the signal of the other has been studied in detail. Empirical equations have been used to overcome this effect, thus allowing the accurate determination of both acids in binary mixtures, without a separation step. The method has been applied to the determination of ASA and SA in blood serum and to the determination of SA impurities in aspirin formulations. Recoveries from sera spiked with both ASA (2.5-50 micrograms ml-1) and SA (100-160 micrograms ml-1) varied from 99.5 to 106.7% (mean = 102.6%) and from 93.0 to 98.0% (mean = 95.8%), respectively. Recoveries of SA from spiked aspirin solutions (0.25-1.5 mg g-1 of aspirin) varied from 98.0 to 102.0% (mean = 100.3%).     

Determination of arsenic in biological fluids by electrothermal atomic absorption spectrometry

A procedure for the determination of the total content of arsenic in urine, serum and blood by electrothermal atomic absorption spectrometry (ETAAS) is described. Zeeman correction is used to compensate the high background signals. The samples are diluted (1 + 1 for urine and 1 + 3 for both serum and blood samples) in a medium containing 0.1% w/v Triton X-100 before being introduced directly into the furnace. A solution containing 15% w/v hydrogen peroxide, 0.65% w/v nitric acid and 0.5% w/v nickel is also introduced into the atomizer by means of a separate injection. Calibration is carried out against aqueous standards for blood and serum samples and using the standard additions method for urine samples. The detection limit is 20 pg (2 ng ml-1). The reliability of the procedure is checked by analyzing three certified reference materials and by recovery studies.     

火焰原子吸收光谱法间接测定药剂中的核黄素

本文利用高碘酸钠对相邻羟基氧化作用的专属性,在一定介质中,高碘酸钠与核黄素完全反应后,过量的高碘酸的钠与硝酸铅或者硝酸铜生成沉淀,通过测定Pb<'2+>或者Cu<'2+>,建立了间接测定核黄素含量的方法.铅体系和铜体系测定的相对标准偏差(RSD)分别为4.8%和5.2%,检出限分别为0.6μg.mL<'-1>和0.5μ...     

Characterization of the metal composition of metallothionein isoforms using reversed-phase high-performance liquid chromatography with atomic absorption spectrophotometric detection

Reversed-phase high-performance liquid chromatography (RP-HPLC) was used to separate metallothionein (MT) isoforms and on-line atomic absorption spectrophotometric (AAS) detection was used to quantitatively determine their metal content. With this coupled system (HPLC-AAS), it was possible to determine the zinc, cadmium and copper content of individual horse kidney MT isoforms. When rabbit liver MT and the purified isoforms (MT-1 and MT-2) were subjected to RP-HPLC and the zinc-containing peaks of the MT sample to MT-1 or MT-2. HPLC-AAS was used to identify zinc-induced MT in heat-treated cytosol from turkey hen liver, thereby demonstrating its application to the analysis of crude tissue extracts. A standard curve was established using turkey liver MT for the quantitative determination of the zinc content of MT isoforms. There was excellent linear correlation between the micrograms of zinc bound to MT injected onto the column (ranging from 0.34 to 3.43 micrograms of MT-bond zinc) and the integrated peak area of the atomic absorbance for zinc. Using this standard curve, it was possible to quantitate the amount of MT-bound zinc in cytosol extracts of cultured turkey embryo hepatocytes exposed to varying levels of supplemental zinc in the culture medium.     

Extraction--spectrophotometric determination of oxalate in urine and blood serum

An extraction--spectrophotometric method is described for the determination of oxalate, based on the formation of a mixed ligand vanadium (V)--mandelohydroxamic acid--oxalate complex. The complex was extracted into a solution of trioctylmethylammonium chloride (Adogen 446) in toluene and the absorbance measured at 535 nm. The experimental variables and interferences in this determination were studied. The detection limit is 0.5 microgram ml-1 and the range of application is between 2 and 8 micrograms ml-1. The method was applied to the determination of oxalate in urine and blood serum.     

原子吸收光度法间接测定甲基托布津的含量

用标准Cu^2 溶液和样品中的甲基托布津在氨碱性环境下作用，产生定量沉淀，离心分离未反应的Cu^2 ，用原子吸收分光光度计测定Cu^2 浓度可间接求得样品中的甲基托布津的含量。本法的检出限10mg/L；测定范围为10-120mg/L；RSD小于3．2％。本方法的测定结果与络合滴定法与分光光度法的结果能很好地符合。     

A highly sensitive spectrophotometric method for the determination of some phenothiazine antipsychotics using chloramine-T and indigocarmine.

A new simple, accurate and precise spectrophotometric method for the determination of six phenothiazine drugs in pure form and in dosage forms is described. The method is based on the oxidation of the studied drugs by a known excess of Chloramine-T in hydrochloric acid medium and subsequent determination of the unreacted oxidant by reacting it with indigocarmine in the same acid medium. The reacted oxidant corresponds to the drug content. The colored species exhibits maximum absorption at 610 nm. The apparent molar absorptivity values and Sandell sensitivity values are in the range 1.53 x 10(4)-2.96 x 10(4) l mol-1 cm-1 and 13.75-37.15 ng cm-2, respectively. The method is highly sensitive and suitable for 1-15 micrograms ml-1 concentrations with the detection limits being in the range, 0.0651-0.1724 microgram ml-1. The method was successfully applied to the studied drugs in their dosage forms. The results are reproducible within +/- 1% and compare favorably with those obtained by the procedures of the British Pharmacopeia.     

Extractive spectrophotometric determination of tungsten(VI) in alloy steels using ethopropazine hydrochloride.

Ethopropazine hydrochloride (EPH) has been proposed as a sensitive reagent for the spectrophotometric determination of tungsten(VI). The method is based on the formation of a chloroform-soluble yellow-colored ternary complex by the interaction of EPH and thiocyanate with tungsten(V). The complex exhibits the absorption maximum at 404 nm with Sandell's sensitivity value of 20.03 ng cm-2. The complex obeyed Beer's law in the concentration range of 1-15 micrograms ml-1 with an optimum concentration range of 2.3-12.9 micrograms ml-1. The effects of foreign ions in the determination of tungsten(VI) were investigated. The method has also been successfully applied to the analysis of alloy steels.     

The indirect determination of organic compounds by atomic absorption spectrometry

The feasibility of determining indirectly certain organic compounds by precipitation of insoluble silver compounds and determining the excess silver(I) by atomic absorption spectrometry (AAS) has been demonstrated. The determination of other compounds, such as alkylated barbiturates and mercaptans by similar methodology should be possible. Although direct AAS methods are preferable to indirect methods, the insolubility of many silver salts, the inherent sensitivity of the AAS method for silver, and the speed and convenience of AAS methodology suggests that under certain conditions, an indirect AAS method may be appropriate and the method of choice.