Influence of Surfactant and Humidity on Sol-Gel Macroporous Organosilicate Coatings

In the preparation of macroporous hydrophobic organosilicate films using methyltriethoxysilane (MTES) as precursor, the effects of surfactant addition, surfactant properties and atmospheric humidity were explored. As films dried, preferential evaporation of the ethanol resulted in an increase of the relative water content. This led to development of phase separation between the hydrophobic gel and the aqueous liquid and ultimately the formation of macropores. In the presence of surfactant, surfactant adsorption at the aqueous phase/gel interface affected the extent of phase separation therefore the resulting pores. Span 20 surfactant (HLB = 8.6) has lower compatibility with the aqueous phase than Tween 20 (HLB = 16.7) and effectively increases the hydrophobicity of the gel phase leading to the formation of larger pores. An increase in Span 20 content from 2 wt.% to 5 wt.% also increased pore size. Film porosity also increased significantly with humidity inside the coating chamber. It would appear that the increased porosity is a result of increased phase separation caused by reduced water evaporation at the higher humidity. Highly macroporous (up to 80% porosity), reproducible and uniform films were obtained by incorporating Span 20 surfactant into the coating solutions and performing dip coating at 80% relative humidity.     

Hydrophobic drying and hysteresis at different length scales by molecular dynamics simulations

We performed molecular dynamics simulations to investigate hydrophobic interactions between two parallel hydrophobic plates immersed in water. The two plates are separated by a distance D ranging from contact to a few nanometers. To mimic the attractive hydrophobic force measurement in a surface force experiment, a driving spring is used to measure the hydrophobic force between two hydrophobic plates. The force-distance curves, in particular the force variations from spontaneous drying to hydrophobic collapse are obtained. These details are usually not accessible in the surface force measurement due to the unstable jump into contact. The length-scale effect on the hydrophobic drying during normal approach and the hydrophobic hysteresis during retraction has been studied. We find that the critical distance at which a spontaneous drying occurs is determined by the shorter characteristic dimension of the plate, whereas the hydrophobic hysteresis is determined by the longer characteristic dimension of the plate. The variations of the potential of mean force versus separation during approach and retraction are also calculated. The results show that water confined between two parallel hydrophobic plates is in a thermodynamic metastable state. This comparably high energy state leads to the spontaneous drying at some critical distance.     

Attractive surface force in the presence of dissolved gas: a molecular approach

Despite widespread evidence of the influence of dissolved air on hydrophobic interaction, the mechanisms of observed effects are still unknown. Although some experiments indicate that adsorbed gases can modify the structure of water next to hydrophobic surfaces, gas effects on measured forces have been observed only at large surface separations. Gas-specific depletion of water at a hydrophobic surface has been detected but was not reproduced in subsequent measurements. We use computer simulations to study short-ranged hydrophobic attraction in the absence and presence of dissolved gas and monitor gas adsorption at molecular resolution inaccessible in experiments. Although we observe a significant accumulation of dissolved gases at hydrophobic surfaces, even in supersaturated gas solutions surface concentrations remain too low to induce any significant change in the local structure of water and short-range surface forces. We present direct calculations of the hydrophobic force between model hydrocarbon plates at separations between 1.5 and 4 nm. Although stronger, the calculated solvation force has a similar decay rate as deduced from recent surface force apparatus measurements at a somewhat lower contact angle. Within the statistical uncertainty, short-range attraction is not affected by the presence of dissolved nitrogen, even in supersaturated solution with a gas fugacity as high as 30 atm. Comparisons of the adsorption behavior of N2, O2, CO2, and Ar reveal similar features in contrast to the peculiar suppression of water depletion reported for an Ar solution in a neutron reflectivity experiment. Our calculations reveal a notable difference between pathways to the capillary evaporation of pure water and gas-phase nucleation in confined supersaturated gas solutions.     

Role of buffer concentration and applied voltage in obtaining a good separation in planar electrochromatography

Planar electrochromatography is performed by applying an electric field across a thin layer chromatography (TLC) plate. In addition to electroosmotic flow in the axial direction, there is also flow to the surface of the TLC layer, and this can substantially degrade the quality of separation. This effect is offset by Joule heating which causes evaporation of liquid from the layer surface, and which under some conditions causes degradation of separation quality by excessive drying of the layer. It is shown that pH, buffer concentration, and applied voltage control the balance between liquid being driven to the surface and liquid evaporating from the surface due to Joule heating. Conditions are discussed which result in good separation quality, or in separations degraded by either excessive wetting or drying of the layer. The above separations were performed at constant voltage. A chromatogram is presented that shows that a good separation is also obtained at constant power, i.e. under conditions where there is a constant amount of Joule heating.     

Quasistatic computer simulation study of the shear behavior of Bi- and trilayer water films confined between model hydrophilic surfaces

In this paper, our previous simulations of the shear behavior of confined water monolayers (Pertsin, A.; Grunze, M. Langmuir 2008, 24, 135) are extended to water films two and three monolayers thick. The shear response of the films is studied in the quasistatic regime corresponding to the infinitely low shear rate. In certain ranges of wall-to-wall separations, bilayer films are found to be capable of sustaining shear stress, as is characteristic of solids, while remaining fluidlike in respect of the lateral order and molecular mobility. The relation between the solidlike and fluidlike properties of the films is dependent on the relative alignment of the walls and on the period of the wall lattice. The films become more fluid when the walls are moved out of alignment and when the wall lattice is uniformly compressed or stretched with respect to the "optimum" lattice that favors crystal-like packing. Trilayer films do not sustain shear stress in the whole range of wall-to-wall separations where these films are formed.     

Molecular dynamics simulation study of interaction between model rough hydrophobic surfaces

We study some aspects of hydrophobic interaction between molecular rough and flexible model surfaces. The model we use in this work is based on a model we used previously (Eun, C.; Berkowitz, M. L. J. Phys. Chem. B 2009, 113, 13222-13228), when we studied the interaction between model patches of lipid membranes. Our original model consisted of two graphene plates with attached polar headgroups; the plates were immersed in a water bath. The interaction between such plates can be considered as an example of a hydrophilic interaction. In the present work, we modify our previous model by removing the charge from the zwitterionic headgroups. As a result of this procedure, the plate character changes: it becomes hydrophobic. By separating the total interaction (or potential of mean force, PMF) between plates into the direct and the water-mediated interactions, we observe that the latter changes from repulsive to attractive, clearly emphasizing the important role of water as a medium. We also investigate the effect of roughness and flexibility of the headgroups on the interaction between plates and observe that roughness enhances the character of the hydrophobic interaction. The presence of a dewetting transition in a confined space between charge-removed plates confirms that the interaction between plates is strongly hydrophobic. In addition, we notice that there is a shallow local minimum in the PMF in the case of the charge-removed plates. We find that this minimum is associated with the configurational changes that flexible headgroups undergo as the two plates are brought together.     

Separation of D-lysergic acid diethylamide derivatives using micellar electrokinetic capillary chromatography

By adjusting column temperature and applied electric field, a fast separation in micellar electrokinetic capillary chromatography was developed for the separation of D-lysergic acid diethylamide derivatives. A baseline separation of nine derivatives was accomplished with a run time of less than 12 min by utilizing elevated column temperature (60 degrees C) and an applied electric field of 387 V/cm. The number of plates generated per unit time for the separations completed at elevated temperatures was significantly higher when compared to separations at the same applied electric field but at lower temperatures (20 degrees C).     

Relationship between scattered intensity and separation for particles in an evanescent field

We describe measurements of the scattering of visible light from an evanescent field by both spherical particles (R = 1-10 mum) that are glued to atomic force microscopy (AFM) cantilevers, and by sharp tips (R < 60 nm) that were incorporated onto the cantilevers during manufacture. The evanescent wave was generated at the interface between a flat plate and an aqueous solution, and an atomic force microscope was used to accurately control the separation, h, between the particle and the flat plate. We find that, for sharp tips, the intensity of scattered light decays exponentially with separation between the tip and the plate all the way down to h approximately 0. The measured decay length of scattered intensity, delta, is the same as the theoretical decay length of the evanescent intensity in the absence of the sharp tip. For borosilicate particles, (R = 1-10 mum), the scattering also decays exponentially with separation at large separations. However, when the separation is less than roughly 3delta, the measured scattering intensity is smaller in magnitude than that which would be predicted by extrapolating the exponential decay observed at large separations. For these particles, the scattering approximately fits the sum of two exponentials. The magnitude of the deviation from exponential at contact was roughly 10-15% for R = 1 mum particles and about 30% for larger particles and is larger for s-polarized light. Preliminary experiments on polystyrene particles shows that the scattering is also smaller than exponential at small separations but that the deviation from exponential is larger for p-polarized light. In evanescent wave AFM (EW-AFM) the scattering-separation can be calibrated for situations where the scattering is not exponential. We discuss possible errors that could be introduced by assuming that exponential decay of scattering continues down to h = 0.     

Wetting and absorption of water drops on Nafion films

Water drops on Nafion films caused the surface to switch from being hydrophobic to being hydrophilic. Contact angle hysteresis of >70 degrees between advancing and receding values were obtained by the Wilhelmy plate technique. Sessile drop measurements were consistent with the advancing contact angle; the sessile drop contact angle was 108 degrees . Water drop adhesion, as measured by the detachment angle on an inclined plane, showed much stronger water adhesion on Nafion than Teflon. Sessile water and methanol drops caused dry Nafion films to deflect. The flexure went through a maximum with time. Flexure increased with contact area of the drop, but was insensitive to the film thickness. Methanol drops spread more on Nafion and caused larger film flexure than water. The results suggest that the Nafion surface was initially hydrophobic but water and methanol drops caused hydrophilic sulfonic acid domains to be drawn to the Nafion surface. Local swelling of the film beneath the water drop caused the film to buckle. The maximum flexure is suggested to result from motion of a water swelling front through the Nafion film.     

Evaporation rates of water from concentrated oil-in-water emulsions

We have investigated the rate of water evaporation from concentrated oil-in-water (o/w) emulsions containing an involatile oil. Evaporation of the water continuous phase causes compression of the emulsion with progressive distortion of the oil drops and thinning of the water films separating them. Theoretically, the vapor pressure of water is sensitive to the interdroplet interactions, which are a function of the film thickness. Three main possible situations are considered. First, under conditions when the evaporation rate is controlled by mass transfer across the stagnant vapor phase, model calculations show that evaporation can, in principle, be slowed by repulsive interdroplet interactions. However, significant retardation requires very strong repulsive forces acting over large separations for typical emulsion drop sizes. Second, water evaporation may be limited by diffusion in the network of water films within the emulsion. In this situation, water loss by evaporation from the emulsion surface leads to a gradient in the water concentration (and in the water film thickness). Third, compression of the drops may lead to coalescence of the emulsion drops and the formation of a macroscopic oil film at the emulsion surface, which serves to prevent further water evaporation. Water mass-loss curves have been measured for silicone o/w emulsions stabilized by the anionic surfactant SDS as a function of the water content, the thickness of the stagnant vapor-phase layer, and the concentration of electrolyte in the aqueous phase, and the results are discussed in terms of the three possible scenarios just described. In systems with added salt, water evaporation virtually ceases before all the water present is lost, probably as a result of oil-drop coalescence resulting in the formation of a water-impermeable oil film at the emulsion surface.     

Demonstration of an integrated capillary electrophoresis-laser-induced fluorescence fiber-optic sensor

A unique integrated separation-based fiber-optic sensor for remote analysis, that incorporates capillary electrophoresis (CE) directly at the fiber sensing terminus is described for the first time. Based on laser-induced fluorescence detection, the sensor offers the potential for high sensitivity. Although the broad-band nature of fluorescence spectra limits selectivity, the high separation power of CE provides a unique dimension of selectivity, while permitting a design of diminutive size. Previously reported fluorescence-based sensors that utilize a chemical reagent phase to impart selectivity tend to be inflexible (not readily adaptable to the detection of different species) and "one-measurement-only" sensors. Conversely, the CE-based fiber-optic sensor described here is both versatile and reusable. The analysis speed and the potential for remote control are further attributes which make the system amenable to remote sensing. A "single-fiber" optical detection arrangement and a "single-reservoir" CE system with the fiber-optic probing the outlet of the separation capillary are employed. A preliminary evaluation of the separation characteristics of this CE-based sensor is presented. Highlights include an observed separation efficiency of up to 3000 theoretical plates (8 cm separation capillary) and migration time reproducibility of less than 10% for frontal mode CE separations. The potential utility of the sensor for remote analysis is demonstrated with separations involving the CE analysis of charged fluorescent dyes, CE analysis of metal complexes based on in situ complexation and micellar electrokinetic capillary chromatographic analysis of neutral fluorescent compounds.     

Elevated-temperature ultrahigh-pressure liquid chromatography using very small polybutadiene-coated nonporous zirconia particles

Capillary columns packed with small diameter particles typically lead to low permeability and long separation times in high-performance liquid chromatography. Ultrahigh pressures (>10,000 p.s.i.; 1 p.s.i. is identical with 6,894.76 Pa) can be used to overcome the limitations that small particles impose. Ultrahigh-pressure liquid chromatography (UHPLC) has demonstrated great potential for high-speed and high-efficiency separations. Decreasing the viscosity of the mobile phase by elevating the temperature could additionally reduce the pressure drop and facilitate the use of longer columns or smaller particles to achieve even higher total plate numbers. For this reason, we investigated the use of elevated temperatures in UHPLC. Water-resistant, flexible heater tape covered with insulation was used to provide the desired heat to the column. Polybutadiene-coated 1 microm nonporous zirconia particles were used because of their chemical stability at elevated temperature. A column efficiency as high as 420,000 plates m(-1) was obtained. The effects of temperature and pressure on the separation of parabens were investigated. Separation of five herbicides was completed in 60 s using 26,000 p.s.i. and 90 degrees C.     

Gas solubility in hydrophobic confinement

Measured forces between apolar surfaces in water have often been found to be sensitive to exposure to atmospheric gases despite low gas solubilities in bulk water. This raises questions as to how significant gas adsorption is in hydrophobic confinement, whether it is conducive to water depletion at such surfaces, and ultimately if it can facilitate the liquid-to-gas phase transition in the confinement. Open Ensemble molecular simulations have been used here to determine saturated concentrations of atmospheric gases in water-filled apolar confinements as a function of pore width at varied gas fugacities. For paraffin-like confinements of widths barely exceeding the mechanical instability threshold (spinodal) of the liquid-to-vapor transition of confined water (aqueous film thickness between three and four molecular diameters), mean gas concentrations in the pore were found to exceed the bulk values by a factor of approximately 30 or approximately 15 in cases of N2 and CO2, respectively. At ambient conditions, this does not result in visible changes in the water density profile next to the surfaces. Whereas the barrier to capillary evaporation has been found to decrease in the presence of dissolved gas (Leung, K.; Luzar, A.; and Bratko, D. Phys. Rev. Lett. 2003, 90, 065502), gas concentrations much higher than those observed at normal atmospheric conditions would be needed to produce noticeable changes in the kinetics of capillary evaporation. In simulations, dissolved gas concentrations corresponding to fugacities above approximately 40 bar for N2, or approximately 2 bar for CO2, were required to trigger expulsion of water from a hydrocarbon slit as narrow as 1.4 nm. For nanosized pore widths corresponding to the mechanical instability threshold or above, no significant coupling between adsorption layers at opposing confinement walls was observed. This finding explains the approximately linear increase in gas solubility with inverse confinement width and the apparent validity of Henry's law in the pores over a broad fugacity range.     

Separation of Hydrophobic Neutral Compounds by Microemulsion Electrokinetic Chromatography

Electrokineticchromatography(EKC)istheonlymodeofcapillaryelectrophoresisfOrtheseparationofelectricalneutralcompounds.Theseparationprincipleisbasedonthedifferentpartitionofsolutesbetweenthepseudostationaryphaseandthesurroundingaqueousphase.MicellarEKC(MEKC)provideshighspeedandhighefficiencyseparationforneutralcompoundswithsignificantsolubilityinaqueoussystem'.Theseparationofhydrophobiccompounds,however,givessomeproblems,becauseoftheirpoorsolubilityinaqueousphase.Inourpreviouswork"',somepol…     

A graphical method for understanding the kinetics of peak capacity production in gradient elution liquid chromatography

A novel graphical method for assessing the compromise between conditional peak capacity and separation speed for packed bed columns under gradient conditions has been developed and applied to the separation of peptides. This approach is analogous to and complements the conventional "Poppe plot" used to study plate count in isocratic separations. The use of the new plot can assist the design of appropriate column formats (e.g. particle size and column length) for both dimensions in gradient elution two-dimensional liquid chromatography (2DLC). Particularly for the second dimension of 2DLC, we find that smaller particles provide faster separations even though fast separations based on particles smaller than 2 microm are practically limited by the required miniscule column length. We also find that high temperatures strongly enhance the kinetics of peak capacity production whereas higher pressures help achieve larger absolute peak capacities albeit at the cost of longer analysis time.     

Refractive index of thin, aqueous films between hydrophobic surfaces studied using evanescent wave atomic force microscopy

We have studied the refractive index of a thin aqueous film between microscopic hydrophobic surfaces using evanescent wave atomic force microscopy (EW-AFM). An evanescent wave, generated at a solid-liquid interface, is scattered by AFM tips or glass particles attached to AFM cantilevers. The scattering of this wave is used to determine the refractive index as a function of separation between these surfaces. Measurements were performed on surfaces that were rendered hydrophobic with octadecyltrichlorosilane, which produces solid-water contact angles in excess of 90 degrees. For AFM tips, the average refractive index in the thin film was always equal to that of water when the film was thicker than approximately 100 nm. At smaller separations, the refractive index was always greater than or equal to that of water. This is inconsistent with the formation of air or vapor films and consistent with a small amount of organic material between the surfaces. For colloidal spheres (R approximately 10 microm), we were not able to detect changes in the refractive index of the thin film between the sphere and plate.     

Theory for an order-driven disruption of the liquid state in water

Water is known to exhibit a number of peculiar physical properties because of the strong orientational dependence of the intermolecular hydrogen bonding interactions that dominate its liquid state. Recent full-atom simulations of water in a nanolayer between graphite plates submersed in an aqueous medium have raised the possibility of a new addition to this list of peculiarities: they show that application of a strong, uniform electric field normal to and between the plates can cause a pronounced decrease in particle density, rather than the increase expected from electrostriction theory for polarizable fluids [Vaitheeswaran et al., J. Phys. Chem. B 70, 6629 (2005)]. However, in seeming contradiction to this result, another study that simulated a range of similar systems has reported a less surprising electrostrictive increase in particle density upon application of the field [Bratko et al., J. Am. Chem. Soc. 129, 2504 (2007)]. In this work, we attempt to reconcile these conflicting simulation phenomena using a statistical mechanical lattice liquid model of water in an applied field. By solving the model using mean-field theory, we show that a field-induced transition to a markedly lower-density phase such as that observed in recent simulations is possible within a certain parameter regime, but that outside of this regime, the more conventional electrostrictive result should be obtained. Upon modifying the model to treat the case of bulk water under constant pressure in an applied field, we predict a density drop with rising field, and subsequently observe the predicted behavior in our own molecular dynamics simulations of liquid water. Our findings lead us to propose that the model considered here may be useful in a variety of contexts for describing the trade-off between orientational ordering of water molecules and their participation in the liquid phase.     

Structure of water nanoconfined between hydrophobic surfaces

We report the results of a series of molecular-dynamics simulations of liquid water confined between two graphite plates with separations ranging from 7 to 15 A. Energies and free energies are provided, indicating also the corresponding stability density span of confined water phases. The structure of the different liquid layers is also discussed for all the considered systems. In particular, we studied atomic density profiles, two-dimensional radial distribution functions, hydrogen bonding, and angular orientations near the carbon plates.     

Characterizing hydrophobicity at the nanoscale: a molecular dynamics simulation study

We use molecular dynamics (MD) simulations of water near nanoscopic surfaces to characterize hydrophobic solute-water interfaces. By using nanoscopic paraffin like plates as model solutes, MD simulations in isothermal-isobaric ensemble have been employed to identify characteristic features of such an interface. Enhanced water correlation, density fluctuations, and position dependent compressibility apart from surface specific hydrogen bond distribution and molecular orientations have been identified as characteristic features of such interfaces. Tetrahedral order parameter that quantifies the degree of tetrahedrality in the water structure and an orientational order parameter, which quantifies the orientational preferences of the second solvation shell water around a central water molecule, have also been calculated as a function of distance from the plate surface. In the vicinity of the surface these two order parameters too show considerable sensitivity to the surface hydrophobicity. The potential of mean force (PMF) between water and the surface as a function of the distance from the surface has also been analyzed in terms of direct interaction and induced contribution, which shows unusual effect of plate hydrophobicity on the solvent induced PMF. In order to investigate hydrophobic nature of these plates, we have also investigated interplate dewetting when two such plates are immersed in water.     

Filtering and continuously separating microplastics from water using electric field gradients formed electrochemically in the absence of buffer

Here we use experiments and finite element simulations to investigate the electrokinetics within straight microchannels that contain a bipolar electrode and an unbuffered electrolyte solution. Our findings indicate that in the presence of a sufficiently high electric field, water electrolysis proceeds at the bipolar electrode and leads to variations in both solution conductivity and ionic current density along the length of the microchannel. The significance of this finding is twofold. First, the results indicate that both solution conductivity and ionic current density variations significantly contribute to yield sharp electric field gradients near the bipolar electrode poles. The key point is that ionic current density variations constitute a fundamentally new mechanism for forming electric field gradients in solution. Second, we show that the electric field gradients that form near the bipolar electrode poles in unbuffered solution are useful for continuously separating microplastics from water in a bifurcated microchannel. This result expands the potential scope of membrane-free separations using bipolar electrodes.

Water electrolysis at a bipolar electrode in the absence of buffer forms electric field gradients in a fundamentally new way. These electric field gradients are useful for continuously separating microplastics from water.