Cu/La2O3-ZrO2-Al2O3催化剂的制备及其对NO选择性还原的催化性能

采用将Al（NO3）3、La（NO3）3和ZrOCl2的混合液滴入沉淀剂（NH4）2CO3中的共沉淀法制备La2O3-ZrO2-Al2O3复合载体,然后负载上Cu2＋,制成Cu/La2O3-ZrO2-Al2O3催化剂。考察了该催化剂在富氧条件下对C3H6选择还原NO的催化性能,并借助扫描电子显微镜（SEM）、X射线衍射（XRD）、比表面积测定（BET）、吡啶吸附红外光谱（Py-IR）、程序升温还原（TPR）和热重分析（TG）等方法研究催化剂制备方法与结构、性能的关系。实验结果表明,采用将Al（NO3）3滴入（NH4）2CO3制得的γ-Al2O3能有效地增大催化剂的比表面积,加入La2O3能提高催化剂的热稳定性,加入ZrO2能大幅度增加催化剂表面L酸和B酸的酸量。因此,采用共沉淀法制备的La2O3-ZrO2-Al2O3复合载体能够使Cu/La2O3-ZrO2-Al2O3催化剂具有良好的催化性能,最佳催化活性温度为300℃,NO最大转化率高达88.9%,在有10%水蒸气存在的情况下,仍可达81.9%。     

Cu/La2O3-ZrO2-Al2O3催化剂的制备及其对NO选择性还原的催化性能

采用将Al(NO3)3、La(NO3)3和ZrOCl2的混合液滴入沉淀剂(NH4)2CO3中的共沉淀法制备La2O3-ZrO2-Al2O3复合载体,然后负载上Cu2+,制成Cu/La2O3-ZrO2-Al2O3催化剂。考察了该催化剂在富氧条件下对C3H6选择还原NO的催化性能,并借助扫描电子显微镜（SEM）、X射线衍射（XRD）、比表面积测定（BET）、吡啶吸附红外光谱（Py-IR）、程序升温还原（TPR）和热重分析（TG）等方法研究催化剂制备方法与结构、性能的关系。实验结果表明,采用将Al(NO3)3滴入(NH4)2CO3制得的γ-Al2O3能有效地增大催化剂的比表面积,加入La2O3能提高催化剂的热稳定性,加入ZrO2能大幅度增加催化剂表面L酸和B酸的酸量。因此,采用共沉淀法制备的La2O3-ZrO2-Al2O3复合载体能够使Cu/La2O3-ZrO2-Al2O3催化剂具有良好的催化性能,最佳催化活性温度为300℃,NO最大转化率高达88.9%,在有10%水蒸气存在的情况下,仍可达81.9%。     

钛和锆的添加对MgNi型合金电极电化学性能的影响

用机械球磨法（MA）成功合成了镁基储氢合金MgNi, Mg0.9Ti0.1Ni和Mg0.9Ti0.1Ni0.9Co0.1。研究了其结构和电化学性能。X射线衍射（XRD）和扫描电镜（SEM）结果表明合金为非晶结构，并有少量的Ni衍射峰存在。充放电测试结果表明这一系列合金具有很好的电化学活性。Ti和Co的替代使合金的循环稳定性好于MgNi合金。50周充放电循环后，Mg0.9Ti0.1Ni0.9Co0.1合金的放电容量明显好于MgNi合金，Mg0.9Ti0.1Ni0.9Co0.1的放电容量比MgNi合金高102.8%，比Mg0.9Ti0.1Ni合金高45.49%。在充放电循环过程中，合金电极容量衰减的主要原因是在合金电极表面Mg变成了Mg(OH)2。Tafel极化测试表明Ti和Co的添加可以提高合金电极在碱液中的抗腐蚀性能和提高合金电极的循环稳定性。EIS测试结果表明Ti和Co的替代可以明显提高MgNi型合金表面的电催化活性。     

草酸共沉淀法制备YBCO粉体的热力学分析

采用草酸共沉淀法制备YBCO粉末,计算了不同pH值下草酸盐共沉淀粉末的沉淀率,并对制取YBCO前驱体粉末过程中的Ba(NO3)2-Y(NO3)3-Cu(NO3)2-H2C2O4-H2O体系进行热力学分析,采用XRD对制备的YBCO进行了分析计算。结果表明:溶液中不同草酸根离子浓度下各离子沉淀完全的最佳pH范围不同,当草酸浓度为0.1 mol·L-1,pH为2~6时,溶液中离子的沉淀率达到99%以上。随着草酸根离子浓度增大,完全沉淀时,共沉淀液中各金属离子所需的pH值范围增大。热力学计算与试验结果吻合。草酸共沉淀法制备的YBCO粉末物相纯度高,杂质少,颗粒细小,平均粒径为35.4 nm。     

Yb~(3+),Ho~(3+)共掺氧化钇透明陶瓷的制备及其性能

研究了共沉淀法制备Yb/Ho∶Y2O3纳米粉末及其透明陶瓷的烧结工艺,采用Y(NO3)3、Yb(NO3)3和Ho(NO3)3的混合溶液为母盐溶液,以氨水为沉淀剂,在不同pH值下,用共沉淀法制备得到了碱式硝酸盐前驱体沉淀。1100℃煅烧2h得到Yb/Ho∶Y2O3纳米粉末。采用0.5wt%的TEOS(正硅酸四乙酯)为添加剂,1700～1850℃真空烧结15～25h后,得到了Yb/Ho∶Y2O3透明陶瓷。     

Cu-Bi纳米粉体的制备及其可见光光催化性能研究

以Cu（NO3）2、Bi（NO3）3、COfNH）2为原料,聚乙二醇（PEG）为分散剂,采用均匀共沉淀法制备了Cu-Bi催化剂,用X-射线粉末衍射法、能量色散法、透射电镜和紫外－可见漫反射光谱法对催化剂的组成、粒径大小、表面形貌和光学吸收性能进行了详细表征,并以酸性大红和亚甲基蓝为目标降解物,考察了所制备的Cu－Bi催化剂在可见光下的光催化性能。实验结果表明,该催化剂为类球形纳米粉体,粒度均匀,粒径约50nm。在可见光作用下,该催化剂对酸性大红和亚甲基蓝均表现出良好的光催化性能,且在240min前,对酸性大红的降解率要优于亚甲基蓝;240min后则两者的降解效果相近。     

水热法合成Bi2S3纳米管及其生长机理

以硝酸铋[Bi(NO)3]和硫化钠(Na2S)为反应原料, 采用水热法在120 ℃下反应12 h, 制备出Bi2S3纳米管. 利用X射线粉末衍射(XRD)、扫描电子显微镜(SEM)、透射电子显微镜(TEM)、选区电子衍射(SAED)和高分辨透射电镜(HRTEM)对其结构和形貌进行了表征. 结果表明, 所制备的产物是结晶良好的正交相Bi2S3纳米管, 其外径为100~500 nm, 内径为50~200 nm, 长为1~5 μm. 根据实验结果讨论了Bi2S3纳米管的生长机理. 初步研究了反应温度和矿化剂种类对产物形貌和结构的影响.     

β-Na（Y_（1.5-x-y）Na_（0.5））F_6：Yb_xTm_y纳米颗粒的合成及其上转换发光性质

本文采用水热合成法制备了β-Na（Y1.5-x-yNa0.5）F6：YbxTmy（x=0.2~1.0,y=0.001~0.008）纳米颗粒,并利用X射线粉末衍射仪、透射电子显微镜和F-4600荧光分光光度计表征了其样品的物相、形貌和发光性质.结果表明样品物相为六角相,颗粒平均直径约22nm,并探讨了Yb3＋和Tm3＋掺杂浓度对样品的上转换发光性质的影响,结果表明敏化剂Yb3＋的最佳掺杂浓度为60%,而激活剂Tm3＋的最佳掺杂浓度为0.6%.     

α-K8P2W17CuO61纳米纤维的制备与表征

运用高压静电纺丝和程序焙烧方法，制备α-K8P2W17CuO61纳米纤维丝．通过红外光谱（FT-IR），X-射线粉末衍射（XRD）进行了表征，结果表明制备的纳米丝是纯α-K8P2W17CuO61，扫描电子显微镜照片（SEM）显示焙烧后产物为纳米纤维丝，其平均直径大约为150nm．     

静电纺丝方法制备a2-K8 P2W17 MnO61纳米纤维

运用高压静电纺丝和程序升温焙烧的方法制备了a2-K8P2W17MnO61纳米纤维．通过红外光谱（FT-IR）和X射线粉末衍射（XRD）对纤维进行了表征．结果表明，制备的纳米纤维为纯杂多酸盐a2—K8P2W17MnO61,扫描电子显微镜（SEM）图形显示焙烧后获得纳米纤维的平均直径大约为140nm。     

铁前驱体对Fe/β催化NH3-SCR反应性能的影响

以硝酸铁、氯化铁和二茂铁等为前驱体,采用液相浸渍法制备了Fe/β催化剂,并将其用于氨选择性催化还原脱硝反应.并采用X射线衍射、透射电镜、N2吸附-脱附、H2程序升温还原以及NH3程序升温脱附等手段对催化剂进行了表征.结果表明,以二茂铁为前驱体制得的催化剂的活性明显优于其它两种前驱体.在60000h–1空速条件下,150oC时NOx转化率即可达到50%,260oC可实现完全转化.这是由于二茂铁的应用改善了铁活性物种在β分子筛上的分散度、颗粒尺寸和颗粒分布以及氧化还原性能.     

钙钛矿型复合氧化物CaVO3的制备及对氧还原反应的电催化性能

以五氧化二钒、硝酸钙、柠檬酸和草酸为原料,采用溶胶-凝胶法制备出CaVO₃的前驱体,在氩气保护下1000 ℃煅烧2 h,成功制备出目标产物CaVO₃.对前驱体和目标产物分别进行了傅里叶变换红外(FTIR)光谱、热重(TG)分析、X射线衍射(XRD)和电导率等表征.在1 mol·L^-1的KOH电解质溶液中测试了样品的氧还原反应(ORR)催化性能.结果表明,修饰电极上(ORR)的电子转移数是1.5-1.7,发生的是2电子还原.     

Synthesis and characterization of single-crystal Ce(OH)CO3 and CeO2 triangular microplates

Single-crystal cerium hydroxide carbonate (Ce(OH)CO3) triangular microplates with the hexagonal phase have been successfully synthesized by a hydrothermal method at 150 degrees C using cerium nitrate (Ce(NO3)3.6H2O) as the cerium source, aqueous carbamide as both an alkaline and carbon source, and cetyltrimethylammonium bromide (CTAB) as a surfactant. Single-crystal ceria (CeO2) triangular microplates have been fabricated by a thermal decomposition-oxidation process at 650 degrees C for 7 h using single-crystal Ce(OH)CO3 microplates as the precursor. The shape of the Ce(OH)CO3 microplate was sustained after thermal decomposition-oxidation to CeO2. The products were characterized by X-ray powder diffraction (XRD), transmission electron microscopy (TEM), field-emission scanning electron microscopy (FE-SEM), differential scanning calorimetric analysis (DSC), and thermogravimetric analysis (TG).     

ZnO微晶的水热合成及形貌控制研究

以Zn(NH3)4(Ac)2为前驱体,不加任何模板剂和表面活性剂,低温下通过改变反应条件(如前驱体浓度、反应时间及反应温度),实现了对ZnO微晶形貌和尺度的有效控制.所得花状、蜂窝状、柱状ZnO用X射线衍射仪和扫描电镜进行了鉴定和表征,并初步探讨了不同形貌ZnO微晶的生长机理.     

Ethanol steam reforming on Ni/Al2O3 catalysts: effect of the addition of Zn and Pt

Ni-based catalysts supported on Zn-modified alumina were investigated in the ethanol steam reforming reaction. A commercial γ-alumina was impregnated with different amounts of zinc nitrate (0, 2, 5, 10, 15, 20 wt.% on Zn basis), calcined, and then impregnated with nickel nitrate aqueous solutions. The samples were characterized by a number of techniques: N(2) adsorption at 77 K, X-ray diffraction (XRD), transmission electron microscopy (TEM), X-ray fluorescence (XRF), and temperature-programmed reduction (TPR). Their catalytic behavior in the ethanol steam reforming reaction was studied at 873 K, with a H(2)O/ethanol ratio of 5:1. Two effects of the presence of Zn were detected. On the one hand, zinc modifies the surface structure and the surface chemistry of the catalysts by formation of zinc aluminates, and on the other hand, zinc oxide can be reduced to metallic zinc under reaction conditions, thus modifying the catalytic properties of the active phase. The presence of Zn increases the ethanol conversion to gaseous compounds as compared with the catalyst supported on the Zn-free commercial alumina. The addition of a small amount of Pt (1 wt.%) causes a beneficial effect in the reaction. When Ni catalysts were used without a previous reduction treatment, ethylene was formed in high amounts; however, the Pt-Ni catalysts need no reduction pre-treatment to achieve high H(2) yields (close to 70%) and showed a high stability versus time on stream because of the control of the production of ethylene, a coke precursor.     

双金属Ag-Cu枝晶的制备及应用

通过铜箔基体上电沉积泡沫铜结合伽尔瓦尼置换反应制备出了银-铜(Ag-Cu)纳米枝晶, 利用X射线衍射(XRD)和场发射扫描电子显微镜(FE-SEM)对枝晶的成分及形貌进行研究发现, 随着沉积过电位的增加, 铜的前驱体形貌由棒状到枝晶状, 最后发展为泡沫状, 但泡沫状的前驱体制备的Ag-Cu 枝晶却是最规整和致密的. 另外, 银离子的浓度也会影响枝晶的形貌, 一定范围内浓度的增加有利于枝晶的形成. 通过线性扫描伏安和电流-时间曲线对制备的Ag-Cu 枝晶催化性能进行表征, 在电解质溶液中, -0.25 V(相对于饱和甘汞电极(SCE))时有一个明显的双氧水(H₂O₂)还原峰, 这意味着Ag-Cu枝晶对H₂O₂的电还原具有较好的催化活性, 当该电极被用于双氧水传感器时, 电流响应快, 能在3 s 内达到稳态电流, 线性测量范围为0.1-12 mmol·L^-1, 灵敏度可以达到330.36 μA·(mmol·L^-1)^-1·cm^-2, 这点对于提高传感器的准确性非常重要.     

MgFe2O4纳米粉体的水热合成及其表征(英)

MgFe₂O₄ nanoparticles were hydrothermally synthesized at 150 ℃ using iron nitrate [Fe(NO₃)₃·9H₂O], magnesium nitrate [Mg(NO₃)₂·6H₂O] and sodium hydroxide (NaOH) as starting materials by carefully controlling the reaction conditions. The influences of several factors such as presence or absence of Na⁺, molar ratio of Fe³⁺ / Mg²⁺, concentration of mental ions, temperature and reaction time on resultant products were investigated in the hydrothermal process. The sample was characterized by X-ray diffraction (XRD) and transmission electron microscopy (TEM), and its magnetic properties were measured using vibrating sample magnetometer (VSM).     

Environmentally Benign Solution-Based Procedure for the Fabrication of Metal Oxide Coatings on Metallic Pigments

Aluminum pigments were coated with Fe₂O₃ and CuO by solution-based thermal decomposition of the urea nitrate compounds hexakisureairon(III)nitrate and tetrakisureacopper(II)nitrate. The deposition process was optimized to obtain homogeneously coated aluminum pigments. The growth of the surface coatings was controlled by investigation with scanning electron microscopy, energy dispersive X-ray spectroscopy and static light scattering as well as infrared, X-ray diffraction and thermogravimetric analysis. The iron precursor showed an incomplete decomposition in solution, incorporating traces of urea molecules inside the coatings while the copper precursor showed complete dissociation accompanied by in situ formation of amine complexes. The amount of organic residues resulting from ligand fragments in the final oxide coatings could be reduced to 22 % for the iron oxide and 12 % for the copper oxide by further temperature treatment in solution (259 °C). Colorimetric investigations of the obtained pigments revealed an excellent hiding power, outperforming the pigments used in current state-of-the-art formulations.     

A simple synthesis route and characterisation of Co(3)Mo(3)C

A simple, one-step thermal decomposition method for the preparation of Co(3)Mo(3)C is reported in this paper. In this novel synthesis route, a mixed-salt precursor, containing Co(CH(3)COO)(2) x 4H(2)O, (HMT)(2)(NH(4))(4)Mo(7)O(24) x 2H(2)O (HMT = hexamethylenetetramine), and excess HMT is directly decomposed to the bimetallic carbide under flowing argon at 1023 K. The role of HMT in the preparation process has been investigated and a detailed reaction mechanism is proposed based on the experimental results. The bimetallic carbide is characterised by X-ray diffraction, scanning electron microscopy, high-resolution transmission electron microscopy, BET surface area measurement and X-ray photoelectron spectroscopy. Furthermore, the activity of the as-prepared Co(3)Mo(3)C is evaluated by a 3-methylpyridine hydrodenitrogenation (HDN) reaction. The catalyst produced from this method provides better reactivity compared to the Co(3)Mo(3)C catalyst prepared by the conventional temperature-programmed reduction method.     

Pd-Ag合金纳米线的可见光辅助简易合成及其对乙醇的电催化氧化

以硝酸钯和硝酸银为金属前驱体,乙醇和柠檬酸钠作为还原剂,聚乙烯吡咯烷酮作为稳定剂和导向剂,以普通市售白炽灯作为光源,采用简易可见光辅助液相法合成了Pd-Ag合金纳米线。通过FESEM、TEM、HRTEM、PXRD和UV-Vis等技术对样品的形貌、晶体结构和光学性质进行了表征,并通过循环伏安法和计时电流法研究了Pd-Ag合金纳米线修饰玻碳电极对乙醇的电催化氧化。与相同条件下制备的纳米钯材料相比,Pd-Ag合金纳米线具有更好的电催化活性、抗中毒性和稳定性。