Diode-end-pumped passively Q-switched Nd:Y0.8Lu0.2VO4 laser with Cr:YAG crystal

A diode end-pumped passively Q-switched Nd: Y_0.8Lu_0.2VO₄ laser with a Cr⁴⁺: YAG crystal is first demonstrated in this paper. The maximum continuous wave (CW) output power of 5.59 W is obtained at the incident pump power of 13.07 W with the output transmission T = 20%, resulting in an optical-to-optical efficiency of 42.7%. For Q-switching operation, the measured pulse duration of 8.5 ns, the pulse energy of 45.24 μJ and the peak power of 5.32 kW are respectively obtained for the output transmission of 50% when the Cr⁴⁺: YAG crystal is used with an initial transmission (T₀) of 60%.     

Continuous wave and passively Q-switched laser performance of the mixed crystal Nd:Lux(x = 0.5)Y1 − x VO4

Diode end-pumped continuous-wave and passively Q-switched Nd:Lu_x(x = 0.5)Y_1 − xVO₄ mixed crystal lasers were demonstrated. At the pump power of 12.6 W, the maximum output power of 6.7 W around 1066.5 nm was obtained with the output transmission of 27%. The optical conversion efficiency is 53.2%, corresponding to a slope efficiency of 55.8%. For pulsed operation, the shortest pulse width attained was 8.6 ns, with the pulse repetition frequency of 99 kHz, and the single pulse energy and the peak power were estimated to be 25.5 μJ and 2.96 kW, respectively.     

High power diode-pumped passively Q-switched and mode-locking Nd:GdVO4 laser at 912 nm

A high power diode-end-pumped passively Q-switched and mode-locking (QML) Nd:GdVO₄ laser at 912 nm was demonstrated for the first time, to the best of our knowledge. A Z-type laser cavity with Cr⁴⁺:YAG crystals as the intracavity saturable absorber were employed in the experiments. Influence of the initial transmission (T_U) of the saturable absorber on the QML laser performance was investigated. Using the T_U = 95% Cr⁴⁺:YAG, as much as an average output power of 2.0 W pulsed 912 nm laser was produced at an absorbed pump power of 25.0 W, then the repetition rates of the Q-switched envelope and the mode-locking pulse were ~ 224 kHz and ~ 160 MHz, respectively. Whereas the maximum output power was reduced to 1.3 W using the T_U = 90% Cr⁴⁺:YAG, we obtained a 100% modulation depth for the mode-locking pulses inside the Q-switched envelope.     

Diode-pumped passively Q-switched Nd:LuxY1−xVO4 laser at 1.34 μm with two V:YAG saturable absorbers

Laser performance with the mixed Nd:Lu_0.15Y_0.85VO₄ crystal at 1.34 μm wavelength has been demonstrated. The continuous wave (cw) operation was carried out in a simple plano-concave resonator with an optical conversion efficiency of 23% and a slop efficiency of 25%. At a pump power of 6.78 W, the Q-switched pulses with the largest average output power of 349 mW, the shortest pulse width of 30.6 ns, the largest repetition rate of 42.5 kHz, the highest peak power of 268 W and the largest pulse energy of 8.2 μJ were obtained, corresponding to the V:YAG with initial transmission of 89%.     

494.5 nm generation by sum-frequency mixing of diode pumped neodymium lasers

We report a coherent radiation at 494.5 nm by intra-cavity sum-frequency generation of 912 nm Nd:GdVO₄ laser and 1080 nm Nd:CaYAlO₄ laser. Blue laser is obtained by using a doubly folded cavity, type-II critical phase matching KTP (KTiOPO₄) crystal sum-frequency mixing. With total pump power of 33 W (13.8 W pump power for 1080 nm Nd:CaYAlO₄ laser and 19.2 W pump power for 912 nm Nd:GdVO₄ laser), TEM₀₀ mode blue laser at 494.5 nm of 1.6 W is obtained. The power stability in 30 min is better than 3.5%.     

Efficient and compact intracavity-frequency-doubled YVO4/Nd:YVO4/KTP laser through analysis of the interaction length

In this paper, a stable end-pumped intracavity-frequency-doubled green laser was demonstrated. The interaction length of different pump systems before setting up the experiment was analyzed in order to find out an effective pump system. The experimental results indicate that the pump system in our configuration is beneficial to the efficient CW Nd lasers. A continue-grown composite crystal YVO₄/Nd:YVO₄, with Nd³⁺ concentration doping of 0.3 at.%, is used as laser medium. With an incident pump power of 27.5 W, as high as 7.2 W of CW output power at 532 nm was achieved. The optical-to-optical conversion efficiency of 26.2% was obtained in CW modes with a flat-flat cavity design.     

Passively Q-switched laser operation in a composite Nd:YVO4/Nd:YVO4/Nd:YVO4 crystal with a GaAs saturable absorber

By using a piece of GaAs wafer as the saturable absorber, the performance of the passively Q-switched composite Nd:YVO₄ laser with different output couplers has been demonstrated for the first time as far as we know. The largest continuous wave output power of 1.52 W is obtained at the incident pump power of 5.31 W, giving an optical conversion efficiency of 28.7% and a slope efficiency of 30.2%. The shortest pulse width of 11 ns, the largest single-pulse energy of 2.49 μJ and the highest peak power of 190 W are also obtained.     

Theoretical and experimental investigations of a diode-pumped high-power continuous-wave 912 nm Nd:GdVO4 laser operation at room temperature

Based on the rate equation of Nd³⁺-doped quasi-three-level lasers, a theoretical model of diode-end-pumped continuous-wave 912 nm Nd:GdVO₄ laser is presented. Lasing threshold and slope efficiency considering reabsorption effect are calculated and analyzed. It is found that the output performance of 912 nm laser operating at room temperature is influenced remarkably by the reabsorption loss and spatial distribution of the pump beam and laser beam. In experiments, the output power and average slope efficiency of 912 nm laser were investigated under different conditions. After optimization at the parameters of laser medium, working temperature and spatial distribution of the pump beam, up to 16.2 W continuous-wave 912 nm laser output was obtained at incident pump power of 67.0 W, with an average slope efficiency of 41.7%, to the best of our knowledge, this is the highest output power of diode-pumped 912 nm Nd:GdVO₄ laser by far.     

A kilowatt level diode-side-pumped QCW Nd:YAG ceramic laser

We demonstrate a kilowatt level Quasi-continuous-wave (QCW) diode-side-pumped Nd:YAG ceramic laser at 1064 nm. The laser system adopts a master oscillator power amplifier scheme (MOPA). The master oscillator contains two diode-pumped laser modules. Under the pump power of 2000 W, an output power of 686 W was obtained. After amplified by an identical ceramic laser module, a maximum output power of 1020 W was obtained under a total incident pump power of 3433 W, corresponding to an optical-optical conversion efficiency of 29.7%. At the maximal output power, the repetition frequency was measured to be 1 kHz and the pulse width was 114 μs. To the best of our knowledge, this is the first time to realize QCW side-pumped Nd:YAG ceramic laser system with output power above 1 kW.     

Diode-pumped passively Q-switched Nd:LuVO4 laser at 916 nm

We demonstrate a passively Q-switched Nd:LuVO₄ laser at 916 nm by using a Nd, Cr:YAG crystal as the saturable absorber. As we know, it is the first time to realize the laser with a simple linear resonator. When the incident pump power increased from 14.6 W to 23.7 W, the pulse width of the Q-switched laser decreased from 24 ns to 21 ns. The pulse width was insensitive to the incident pump power in the experiment. The average output power of 288 mW with repetition rate of 39 kHz was obtained at an incident pump power of 22.5 W, with the optical-to-optical efficiency and slope efficiency 1.3% and 3.6%, respectively.     

Continuous-tunable 4.144-4.851 μm twin-MgO:PPLN cascaded optical parametric generator pumped by a 1.342 μm Nd:GdVO4 laser

An all-solid-state mid-infrared optical parametric generator with wide tunability by using multi-grating periodically poled 5 mol.-% MgO-doped lithium niobate (MgO:PPLN) is reported. The pump source is a diode-pumped Q-switched Nd:GdVO₄ laser operated at 1.342 μm with pulse width of 150 ns and repetition rate of 50 kHz. To extend the interaction length, two identical multi-grating MgO:PPLN crystals have been cascaded in the OPG system. When the incident pump average power is 10 W, the obtained maximum idler output power is 340 mW at 4.144 μm. Compared with only using one multi-grating MgO:PPLN crystal, the obtained idler output power increases by 20.1%. 4.144-4.851 μm continuous-tunable idler output is obtained with six grating periods from 29 to 31.5 μm and temperature from 40 to 200 °C. To our knowledge, this is the first time to use 1.342 μm laser as the pump source of OPG.     

LD end-pumped intracavity frequency doubled Yb:YAG laser

A laser diode end-pumped 10 at.% doped Yb:YAG microchip crystal intracavity frequency doubled all solid-stated green laser is reported in this paper. Using one plano-concave resonator, with the pump power of 1.2 W, 44.2 mW TEM₀₀ continuous wave (CW) laser at 525 nm was obtained, the optical conversion efficiency was about 3.7%. When a Cr:YAG crystal with initial transmission of 95.5% inserted in the resonator, the maximum output power of 6.4 mW, pulse duration width of 49.1 ns, pulse repetition rate of 2.45 kHz, and peak power of 53.1 W at 515 nm were achieved when the pump power was 1.2 W. The wavelength changed from 525 nm to 515 nm and the threshold was only 725 mW.     

Q-switched fiber laser by all-fiber piezoelectric modulation and pulsed pump

We have demonstrated a Q-switched fiber laser based on a mechanical all-fiber Q-switching module and pulsed-pump configuration. A piezoelectric actuator was utilized in the module to change the round-trip loss of the fiber laser cavity, and exploited the pulsed pump to prevent the multiple pulsing phenomena. Q-switching pulses were successfully achieved at the repetition rates from 1 Hz to 2 kHz, and the average output power was 11 mW. The peak power in excess of 114 W with associated pulse width of 193 ns was obtained at the repetition rate of 500 Hz. Besides preventing multiple pulsing phenomena, pulsed-pump configuration can also suppress amplified spontaneous emission and increase pulse stability and peak power simultaneously.     

Diode-pumped passively Q-switched 912 nm Nd:GdVO4 laser and pulsed deep-blue laser by intracavity frequency-doubling

A diode-end-pumped passively Q-switched 912 nm Nd:GdVO₄/Cr⁴⁺:YAG laser and its efficient intracavity frequency-doubling to 456 nm deep-blue laser were demonstrated in this paper. Using a simple V-type laser cavity, pulsed 912 nm laser characteristics were investigated with two kinds of Cr⁴⁺:YAG crystal as the saturable absorbers, which have the different initial transmissivity (T_U) of 95% and 90% at 912 nm. When the T_U = 95% Cr⁴⁺:YAG was used, as much as an average output power of 2.8 W 912 nm laser was achieved at an absorbed pump power of 34.0 W, and the pulse width and the repetition rate were ∼ 40.5 ns and ∼ 76.6 kHz, respectively. To the best of our knowledge, this is the highest average output power of diode-pumped passively Q-switched Nd³⁺-doped quasi-three-level laser. Employing a BiBO as the frequency-doubling crystal, 456 nm pulsed deep-blue laser was obtained with a maximum average output power of 1.2 W at a repetition rate ∼ 42.7 kHz.     

Diode-end-pumped composite Nd:YVO4 yellow laser based on intracavity frequency-doubled self-Raman laser

We report an intracavity frequency-doubled Q-switched self-Raman yellow laser at 587 nm. A composite Nd:YVO₄ crystal was utilized as self-Raman gain medium. The maximum average output power of yellow light obtained was 1.5 W at the incident pump power of 30 W and at a repetition rate of 50 kHz, corresponding to the optical conversion efficiency of 5%. The shortest pulse width, the maximum pulse energy and the highest peak power were measured to be 5.8 ns, 46.7 μJ and 5.9 kW, respectively.     

Lasing of a single crystal Nd fluoride fiber

We present laser action in a single crystal fluoride fiber obtained by the micro-pulling-down technique. The 700 μm diameter and 1 cm long Nd:LiYF₄ fiber was pumped by a beam shaped diode bar emitting at 806 nm. A peak power of 300 mW was achieved with a slope efficiency of 12%. When considering the pump power fraction absorbed by the laser mode, a slope efficiency of 37% was achieved. To the best of our knowledge, this is the first report of a Nd: LiYF₄ fiber laser.     

Highly efficient and compact laser-diode end-pumped Q-switched Nd:YVO4/KTP red laser

A laser-diode end-pumped acousto-optic (AO) Q-switched Nd:YVO₄/KTP red laser by using a plano-concave cavity was demonstrated for the first time. This linear cavity configuration could guarantee not only moderate intracavity focusing on KTP crystal but also good beam quality. Under the absorbed pump power of 14.8 W, the maximum average output power at 671 nm was obtained to be 1.37 W at the repetition frequency of 15 kHz, with the corresponding optical conversion efficiency of 9.3% and the pulse width of 33 ns. The energy of a single pulse and corresponding peak power are estimated to be 91.3 μJ and 2.77 kW, respectively. The rate equations are also numerically solved by introducing the nonlinear loss resulting from generation of second-harmonic wave.     

800 mW/1484 nm highly efficient two-cascaded phosphosilicate Raman fiber laser pumped by Nd:YVO4 solid-state laser

Using 1064 nm CW Nd:YVO₄ solid-state laser as a pump, 1-km phosphosilicate fiber and cascaded cavities with two pairs of fiber Bragg grating mirrors for 1239 and 1484 nm, we obtained a CW 800 mW/1484 nm Raman fiber laser (RFL) for an actual incident pump power of about 2 W (Nd:YVO₄ power of 6.90 W). The conversion efficiency is as high as 40%. To the best of our knowledge, this is the highest conversion efficiency of RFL pumped by solid-state laser. The output power instability at 1484 nm in half an hour is less than 3%. In addition, the numerical simulations are also performed. Good agreement between the results of numerical simulation and the results of the experiment has been demonstrated.     

An efficient and compact laser-diode end-pumped intracavity frequency-tripled Nd: YVO4 355 nm laser

By exploiting the intracavity frequency conversion configuration, a diode end-pumped acousto-optic (AO) Q-switched Nd:YVO₄ 355 nm laser was demonstrated in this paper. Two LBO crystals were inserted in the cavity to realize the frequency tripling operation, a cascade of the second harmonic generation (SHG) and sum frequency mixing (SFM). Under the absorbed pump power of 13 W, the maximum average output power at 355 nm was obtained to be 1.32 W at the repetition frequency of 17 kHz, with the optical-to-optical conversion efficiency of 10.2%. The corresponding pulse width was 10.2 ns, with the energy of a single pulse and corresponding peak power estimated to be 77.6 μJ and 7.61 kW, respectively.     

High efficiency generation of 355 nm radiation by extra-cavity frequency conversion

High efficiency extra-cavity third harmonic generation (THG) of 355 nm has been developed. A laser diode (LD) end-pumped, acoustic-optical Q-switched Nd:YAG laser was used as the fundamental wave source. With an input pump power of 25 W, average power of 6.75 W at 1064 nm was generated with the repetition rate 12 kHz and pulse duration 10 ns. Using the extra-cavity frequency conversion of three critical phase match (CPM) LiB₃O₅ (LBO) crystals, 3.2 W third harmonic radiation at 355 nm was obtained. The optical-to-optical (1064 nm to 355 nm) conversion efficiency was up to 47.4%.