On the numerical study of bubbly flow created by ventilated cavity in vertical pipe

The dispersion of bubbles into a down-liquid flow in a vertical pipe is investigated. At low flow rates, the intended design of a swarm of discrete bubbles is achieved. At high flow rates, a ventilated cavity is nonetheless formed, which is attached close to the gas sparger. Behind this ventilated cavity, three different flow regimes characterize the complex bubbly flow field downstream of the down-liquid flow: vortex region with high void fraction, transitional region and pipe flow region. In this study, a numerical model that solved the entire development of the gas–liquid flow including the extended single-phase liquid region upstream to the wall-jet and recirculating-vortex zones in order to allow a more realistic determination of the boundary conditions of the down-liquid flow was adopted. Coupling with the Eulerian–Eulerian two-fluid model to solve the respective gas and liquid phases, a population balance model was also applied to predict the bubble size distribution in the wake right below the cavity base as well as further downstream in the transitional and fully-developed pipe flow regions. The numerical model was evaluated by comparing the numerical results against the data derived from theoretical, numerical and experimental approaches. Prediction of the Sauter mean bubble diameter distributions by the population balance approach at different axial locations confirmed the dominance of breakage due to the high turbulent intensity below the ventilated cavity which led to the generation of small gas bubbles at high void fraction. Further downstream, the coalescence effect dominated leading to merging of the small bubbles to form bigger bubbles.     

Visualization of flow boiling of liquid nitrogen in a vertical mini-tube

The flow boiling patterns of liquid nitrogen in a vertical mini-tube with an inner diameter of 1.931 mm are visualized with a high-speed digital camera. The superficial gas and liquid velocities are in the ranges of 0.01–26.5 m/s and 0.01–1.2 m/s, respectively. Four typical flow patterns, namely, bubbly, slug, churn and annular flow are observed. Some interesting scenes about the entrainment and liquid droplet deposition in the churn and annular flow, and the flow reversal with the indication of negative pressure drop, are also presented. Based on the visualization, the two-phase flow regime maps are obtained. Compared with the flow regime maps for gas–water flow in tubes with similar hydraulic diameters, the region of slug flow in the present study reduces significantly. Correspondingly, the transition boundary from the bubbly flow to slug flow shifts to higher superficial gas velocity, and that of churn to annular flow moves to lower superficial gas velocity. Moreover, time-averaged void fraction is calculated by quantitative image-digitizing technique and compared with various prediction models. Finally, three kinds of oscillations with long-period and large-amplitude are found, possible explanation for the oscillations is given by comparing the instantaneous flow images with the data of pressure, mass flux and temperature recorded synchronously.     

Simulation of large amplitude waves in a slug tracking scheme compared to roll wave experiments at high pressure

Due to the similarities between large amplitude roll waves and slug flow in two-phase gas–liquid pipe flow, a slug tracking scheme is presented with the addition of a simplified model for roll waves. The waves are treated in a similar way to slugs, modelled as objects moving at the wave velocity and with a pressure variation across them. The two-fluid model is solved on a stationary staggered grid in stratified sections between moving waves and slugs. The model is dynamic meaning that the growth and decay of waves and slugs can be simulated. The wave model implementation within the tracking scheme is discussed and demonstrated in comparison to existing experimental data on wave velocities and averaged pressure drops. The results from the tracking scheme compared well to the experiments when waves were initiated with the experimental frequency. Wave initiation remains as a modelling challenge.     

Studying disturbance waves in vertical annular flow with high-speed video

In many annular two-phase gas–liquid flows, large disturbance waves propagate liquid mass. These waves are important for modeling of gas-to-liquid momentum transfer and liquid film behavior. High-speed videos of vertical upflow have been analyzed to extract individual and average wave data. Two types of structures, coherent waves and piece waves, have been identified in these flows. Velocities, lengths, and temporal spacings of individual waves and average velocities, lengths, frequencies, and intermittencies have been studied as functions of both gas and liquid flow rates. Velocity and frequency increase with liquid and gas flow rates, length decreases with increasing gas flow and increases with increasing liquid flow, and intermittency is predominantly an increasing function of liquid flow.     

Modeling of three-phase heavy oil–water–gas bubbly flow in upward vertical pipes

A bubbly gas–bubbly oil flow pattern may occur when water, heavy oil and gas flow simultaneously in vertical pipes in such a way that water is the continuous phase. In this work, a one-dimensional, thermal, transient two-fluid mathematical model, for such flow, is presented. The model consists of mass, momentum and energy conservation equations for every phase whose numerical solution is based on the finite difference technique in the implicit scheme. The model is able to predict pressure, temperature, volumetric fraction and velocity profiles. For accurate modeling of multiphase flows, the key issue is to specify the adequate closure relationships, thus drag and virtual mass forces for the gas and oil phases were taken into account and special attention was paid on the gas–oil drag force. When this force was included into the model it was found that: (1) such force had the same order of magnitude than the oil drag force and both forces were smaller than the gas drag force, (2) the pressure, gas and oil velocities and gas and oil volume fraction profiles were affected, (3) the numerical stability was increased. The model predictions are in agreement with experimental data reported in literature.     

On two-phase flow patterns and transition criteria in aqueous methanol and CO2 mixtures in adiabatic,rectangular microchannels

This paper presents flow map investigations of adiabatic two-phase flow in square cross-sectioned, 200 μm deep microchannels fabricated in silicon, employing laser induced fluorescence microscopy. The influence of surface tension and nozzle geometry on the flow pattern transition was investigated using two nozzle widths (orifices of 30 μm and 50 μm, respectively) and methanol–water solutions with CO₂ as the gas phase. It was found and quantified that smaller nozzle geometries and smaller liquid surface tension promote the propagation of capillary gas bubbles at lower superficial gas and liquid velocities. Within the measurement domain of superficial gas (0.01–0.625 m/s) and liquid (0.0005–0.5000 m/s) velocities, we observed dispersed bubbly, regularly ordered bubbly, wedging, slug and annular flows, thus extending the experimental knowledge base to smaller superficial liquid velocities by almost two orders of magnitude. With the help of the flow maps presented herein, we were able to characterize the observed regularly ordered bubbly flow as the transition regime between dispersed bubbly and wedging flow. The results of the present investigation are of direct relevance to the operation of small-scale direct methanol fuel cells.     

Hydrodynamic and mass transfer characteristics of slug flow in a vertical pipe with and without dispersed small bubbles

In this work, we present a numerical study to investigate the hydrodynamic characteristics of slug flow and the mechanism of slug flow induced CO₂ corrosion with and without dispersed small bubbles. The simulations are performed using the coupled model put forward by the authors in previous paper, which can deal with the multiphase flow with the gas–liquid interfaces of different length scales. A quasi slug flow, where two hypotheses are imposed, is built to approximate real slug flow. In the region ahead of the Taylor bubble and the liquid film region, the presence of dispersed small bubbles has less impacts on velocity field, because there are no non-regular intensive disturbance forces or centrifugal forces breaking the balance of the liquid and the dispersed small bubbles. In the liquid slug region, the strong centrifugal forces generated by the recirculation below the Taylor bubble lead to the effect of heterogeneity, which makes the profile of the radial liquid velocity component sharper with higher volume fraction of dispersed small bubbles. The volume fraction has a maximum value in the range of r/R = 0.5–0.6. Meanwhile, it is usually higher than 0.35, which means that larger dispersed bubbles can be formed by coalescences in this region. These calculated results are in good agreement with experimental results. The wall shear stress and the mass transfer coefficient with dispersed small bubbles are higher than those without dispersed small bubbles due to enhanced fluctuations. For short Taylor bubble length, the average mass transfer coefficient is increased when the gas or liquid superficial velocity is increased. However, there may be an inflection point at low mixture superficial velocities. For the slug with dispersed small bubbles, the product scales still cannot be damaged directly despite higher wall shear stress. In fact, the alternate wall shear stress and the pressure fluctuations perpendicular to the pipe wall with high frequency are the main cause for breaking the product scales.     

Prediction of the entrained liquid fraction in vertical annular gas–liquid two-phase flow

The study considers the prediction of the entrained liquid fraction in adiabatic gas–liquid annular two-phase flow in vertical pipes. Nine empirical correlations have been tested against an experimental data bank drawn together in this study containing 1504 points for 8 different gas–liquid combinations and 19 different tube diameters from 5.00 mm to 57.1 mm. The correlation of Sawant, Ishii and Mishima and the one of Oliemans, Pots and Trompé were found to best reproduce the available data. A new correlating approach, derived from both physical intuition and dimensional analysis and capable of providing further physical insight into the liquid film atomization process, was proposed and worked better than any of the existing methods. This new correlation is based on the core flow Weber number that is also a controlling dimensionless group in determining the wall shear stress and associated frictional pressure gradient of annular flows.     

On the role of droplets in cocurrent annular and churn-annular pipe flow

Decreasing the gas flow-rate in an initially vertical upward annular dispersed pipe-flow, will eventually lead to a down-flow of liquid. The onset of this down-flow has been related in the literature to the presence of the dispersed phase and the instability of the liquid film. Here we investigate how the dispersed-phase may influence the down-flow, performing detailed PDA-measurements in a 5 cm vertical air–water annular-flow. It is shown that the dispersed-phase does not cause the liquid down-flow, but that it delays the onset of liquid down-flow. In cocurrent annular flow the dispersed phase seems to stabilise the film flow, whereas in churn-annular flow the opposite seems to be true.     

Primary instabilities of liquid film flow sheared by turbulent gas stream

Evolution of excited waves on a viscous liquid film has been investigated experimentally for the annular gas–liquid flow in a vertical tube. For the first time the dispersion relations are obtained experimentally for linear waves on liquid film surface in the presence of turbulent gas flow. Both cocurrent and countercurrent flow regimes are investigated. As an example of comparison with theory, the experimental data are compared to the results of calculations based on the Benjamin quasi-laminar model for turbulent gas flow. The calculation results are found to be in good agreement with experiments for moderate values of film Reynolds number.     

On the liquid turbulence energy spectra in two-phase bubbly flow in a large diameter vertical pipe

The liquid turbulence structure of air–water bubbly flow in a 200 mm diameter vertical pipe was experimentally investigated. A dual optical probe was used to measure the bubble characteristics, while the liquid turbulence was measured using hot-film anemometry. Experiments were performed at two liquid superficial velocities of 0.2 and 0.68 m/s for gas superficial velocities in the range of 0–0.18 m/s, corresponding to an area averaged void fraction up to 13.6%. In general, there is an increase in the liquid turbulence energy when the bubbles are introduced into the liquid flow. The increase in the energy mainly occurs over a range of length scales that are on the order of the bubble diameter. A suppression of the turbulence was observed close to the wall at very low void fraction flows. Initially, the suppression occurs in the low wave number range and then extends to higher wave numbers as the suppression is increased.     

A coupled model for simulation of the gas–liquid two-phase flow with complex flow patterns

A new model coupling two basic models, the model based on interface tracking method and the two-fluid model, for simulating gas–liquid two-phase flow is presented. The new model can be used to simulate complex multiphase flow in which both large-length-scale interface and small-length-scale gas–liquid interface coexist. By the physical state and the length scale of interface, three phases are divided, including the liquid phase, the large-length-scale-interface phase (LSI phase) and the small-length-scale-interface phase (SSI phase). A unified solution framework shared by the two basic models is built, which makes it convenient to perform the solution process. Based on the unified solution framework, the modified MCBA–SIMPLE algorithm is employed to solve the Navier–Stokes equations for the proposed model. A special treatment called “volume fraction redistribution” is adopted for the special grids containing all three phases. Another treatment is proposed for the advection of large-length-scale interface when some portion of SSI phase coalesces into LSI phase. The movement of the large-length-scale interface is evaluated using VOF/PLIC method. The proposed model is equivalent to the two-fluid model in the zone where only the liquid phase and the SSI phase are present and to the model based on interface tracking method in the zone where only the liquid phase and the LSI phase are present. The characteristics of the proposed model are shown by four problems.     

An appraisal of liquid–liquid slug flow in different pipe orientations

Gas–liquid slug flow occurs over a wide range of phase flow rates and in a variety of practical applications during gas–liquid two-phase flows. The range of slug flow increases further in narrow pipes (<0.0254 m), undulated pipelines, riser tube, etc. On the other hand, the past literature shows that slug flow is rarely observed for liquid–liquid cases. In the present study, an interest was felt to investigate whether liquid–liquid slug flow occurs in situations known for excessive slugging in gas–liquid cases. For this, experiments have been performed in narrow (0.012 m ID) vertical and horizontal pipes and an undulated pipeline of 0.0254 m internal diameter where the V-shaped undulation comprises of an uphill and a downhill section between two horizontal pipes. The studies have been performed for both peak and valley orientation of the undulation. Kerosene and water have been selected as the test fluids and the optical probe technique has been used to supplement visual observations especially at higher flow rates. The studies have revealed the existence of the slug flow pattern over a wide range of phase flow rates in all the three geometries. Interestingly, it has been noted that the introduction of an undulation induces flow patterns which bear a closer resemblance to gas–liquid flows as compared to liquid–liquid flows through a horizontal pipe of 0.0254 m diameter.     

Prediction of the transition from stratified to slug flow or roll-waves in gas–liquid horizontal pipes

In stratified gas–liquid horizontal pipe flow, growing long wavelength waves may reach the top of the pipe and form a slug flow, or evolve into roll-waves. At certain flow conditions, slugs may grow to become extremely long, e.g. 500 pipe diameter. The existence of long slugs may cause operational upsets and a reduction in the flow efficiency. Therefore, predicting the flow conditions at which the long slugs appear contributes to a better design and management of the flow to maximize the flow efficiency.     

A numerical study of an annular liquid jet in a compressible gas medium

An annular liquid jet in a compressible gas medium has been examined using an Eulerian approach with mixed-fluid treatment. The governing equations have been solved by using highly accurate numerical methods. An adapted volume of fluid method combined with a continuum surface force model was used to capture the gas–liquid interface dynamics. The numerical simulations showed the existence of a recirculation zone adjacent to the nozzle exit and unsteady large vortical structures at downstream locations, which lead to significant velocity reversals in the flow field. It was found that the annular jet flow is highly unstable because of the existence of two adjacent shear layers in the annular configuration. The large vortical structures developed naturally in the flow field without external perturbations. Surface tension tends to promote the Kelvin–Helmholtz instability and the development of vortical structures that leads to an increased liquid dispersion. A decrease in the liquid sheet thickness resulted in a reduced liquid dispersion. It was identified that the liquid-to-gas density and viscosity ratios have opposite effects on the flow field with the reduced liquid-to-gas density ratio demoting the instability and the reduced liquid-to-gas viscosity ratio promoting the instability characteristics.     

Application of a borescope to studies of gas–liquid flow in downward inclined pipes

The aim of the present study is to investigate stratified downward gas–liquid pipe flow with a non-intrusive measurement technique that is based on a borescope connected to a digital video camera. The borescope-based technique enables to determine the instantaneous cross-sectional distribution of both phases within the pipe. Water and air were used as working fluids. Quantitative data was extracted from sequences of recorded video images by applying a developed data processing technique for instantaneous gas–liquid interface boundaries determination. Experiments were performed for a wide range of downward pipe inclinations and gas and liquid flow rates. The instantaneous and time-average cross-sectional holdup for each set of flow parameters was calculated. Particular attention was given to the study of the interface shape that in many occasions was not flat and was characterized by the penetration of the liquid along the pipe periphery. Temporal variation of the surface elevation was also studied and various regimes characterizing interfacial waves were defined using both the recorded time series of the instantaneous depth of the water layer and the Fourier analysis of those records.     

Effect of drag reducing polymer on air–water annular flow in an inclined pipe

Drag reduction (DR) for air and water flowing in an inclined 0.0127 m diameter pipe was investigated experimentally. The fluids had an annular configuration and the pipe is inclined upward. The injection of drag reducing polymer (DRP) solution produced drag reductions as high as 71% with concentration of 100 ppm in the pipeline. A maximum drag reduction that is accompanied (in most cases) by a change to a stratified or annular-stratified pattern. The drag reduction is sensitive to the gas and liquid superficial velocities and the pipe inclination. Maximum drag reduction was achieved in the case of pipe inclination of 1.28° at the lowest superficial gas velocity and the highest superficial liquid velocity. For the first time in literature, the drag reduction variations with the square root of the superficial velocities ration for flows with the same final flow patterns have self-similar behaviors.     

Numerical study of elbow erosion due to sand particles under annular flow considering liquid entrainment

Sand particle erosion is always a challenge in natural gas production. In particular, the erosion in gas–liquid–solid annular flow is more complicated. In this study, a three-phase flow numerical model that couples the volume of fluid multiphase flow model and the discrete phase model was developed for prediction of erosion in annular flow. The ability of the numerical model to simulate the gas–liquid annular flow is validated through comparison with the experimental data. On the basis of the above numerical model, the phase distribution in the pipe was analyzed. The liquid entrainment behavior was reasonably simulated through the numerical model, which guaranteed the accuracy of predicting the particle erosion. Additionally, four erosion prediction models were used for the erosion calculation, among them, the Zhang et al. erosion model predicted the realistic results. Through the analysis of the particle trajectory and the particle impact behavior on the elbow, the cushion effect of the liquid film on the particles and the erosion morphology generation at the elbow were revealed.     

Research on multiphase flows in Thermo-Energy Engineering Institute of Southeast University

Multiphase flows have received increasing attention over the past decades. This paper describes the research carried out in Thermo-Energy Engineering Institute of Southeast University in recent years, focusing on several common issues associated with multiphase flows in industry, such as: boiling of falling film and complex structure of gas–liquid flow under large difference in temperature, free surface flows involving liquid jets and drop formation, mixing behaviors of gas–liquid–solid three-phase flow, and fluidization characteristics of cylindrical particles. Numerical methods ranging from empirical to CFD models were developed for predictions, and experimental works were essentially conducted for validation and modification. For all cases, simulated results were validated with experiments and good agreements were obtained. Based on the combined modeling and experimental approach, fundamental understanding of multiphase processes in a specific circumstance is achieved under conditions relevant to the actual industrial-scale, such as transport phenomena, flow patterns, fluid dynamics and interactions between phases.     

Experimental study on axial development of liquid film in vertical upward annular two-phase flow

Accurate measurements of the interfacial wave structure of upward annular two-phase flow in a vertical pipe were performed using a laser focus displacement meter (LFD). The purpose of this study was to clarify the effectiveness of the LFD for obtaining detailed information on the interfacial displacement of a liquid film in annular two-phase flow and to investigate the effect of axial distance from the air–water inlet on the phenomena. Adiabatic upward annular air–water flow experiments were conducted using a 3 m long, 11 mm ID pipe. Measurements of interfacial waves were conducted at 21 axial locations, spaced 110 mm apart in the pipe. The axial distances from the inlet (z) normalized by the pipe diameter (D) varied over z/D = 50–250. Data were collected for predetermined gas and liquid flow conditions and for Reynolds numbers ranging from Re_G = 31,800 to 98,300 for the gas phase and Re_L = 1050 to 9430 for the liquid phase. Using the LFD, we obtained such local properties as the minimum thickness, maximum thickness, and passing frequency of the waves. The maximum film thickness and passing frequency of disturbance waves decreased gradually, with some oscillations, as flow developed. The flow development, i.e., decreasing film thickness and passing frequency, persisted until the end of the pipe, which means that the flow might never reach the fully developed state. The minimum film thickness decreased with flow development and with increasing gas flow rate. These results are discussed, taking into account the buffer layer calculated from Karman’s three-layer model. A correlation is proposed between the minimum film thickness obtained in relation to the interfacial shear stress and the Reynolds number of the liquid.