双束黑洞靶辐射特性实验研究

本文着重介绍在“神光”装置上两路对打黑洞靶辐射特性实验研究。利用两台配置时标装置的亚千电子伏能谱仪(Dante)进行时间关联测量,分别监测双束靶吸收转换区和内爆压缩区泄漏X光谱脉冲波形、辐射能谱、辐射温度、辐射时间谱及其辐射温度随时间变化关系。同时进行了大量不同型号黑洞靶实验,给出吸收转换区辐射温度随注入激光能量面密度变化的关系曲线及其定标关系式。实验中,首次把掠入射平面反射镜用于亚千X光能谱测量,并取得预想的结果。     

长脉冲keV X射线源的辐射特征

 利用神光Ⅱ第九路2 ns长脉冲激光束作用厚钛固体靶，研究了产生的keV X射线源的辐射区域和总辐射功率的时间行为。结果表明：在长脉冲激光作用厚固体靶时，硬X射线线辐射功率的时间行为以及辐射体积的时间行为与激光脉冲波形一致；长脉冲时，等离子体2维膨胀效应非常显著，keV X射线线辐射的径向辐射区域在激光焦斑尺寸附近达到饱和，导致X射线线辐射功率出现饱和，且keV X射线线辐射的辐射体积正比于焦斑尺寸的3次方。从理论和实验角度研究了在同样入射激光能量下，辐射功率随激光焦斑尺寸的变化关系，发现keV X射线线辐射的饱和辐射功率正比于焦斑尺寸的5/3次方，理论结果与实验结果一致。并讨论了相同基频输出激光能量下，keV X射线辐射总功率随激光波长的变化关系，发现即使考虑了倍频效率的影响，短波长激光仍然有利于keV X射线的发射。     

测量等离子体辐射温度的XRD膜吸收法

描述了测量1.05μm强激光轰击黑洞靶时的辐射温度的X射线二级管(XRD)膜吸收法,着重介绍原理、程序计算、滤光膜选择原则和89年LF-12激光器的测量情况,并计算了黑洞靶泄漏X射线能量及辐射温度的时间谱。实验结果与亚千X光射线能谱仪(Dante)的结果在误差范围内符合。     

吸积盘的X射线辐射对周围星际物质的离化研究

利用辐射流体力学程序对三倍频纳秒激光与靶物质相互作用进行了模拟研究，得到了可以产生黑体辐射谱分布的激光等离子体X射线辐射靶的最佳厚度；数值模拟研究了黑体谱分布的X射线辐射场对等离子体系统平均离化度分布的影响，它有助于深入理解天体物理中吸积盘对它周围星际物质的离化影响. 关键词： 辐射流体力学 激光等离子体 X射线辐射 吸积盘 离化     

泵浦靶辐射X射线特性研究

为探索和研究新的X光激光泵浦机制,我们研究了泵浦靶辐射X射线特性。先后在“星光”和“神光”激光装置上开展了该项工作。主要介绍“神光”装置上的实验工作。实验所用泵浦靶材料为Na/F和Cu。实验给出了Na/F和Cu靶辐射X射线谱(波长范围分别为1.1～1.5nm,1.1～1.3nm);给出了X射线相对强度随激光功率密度及靶厚度的变化情况。并比较了靶前、后X射线相对强度。同时,实验还给出了线状泵浦源辐射X射线的空间分布。     

金等离子体M带谱强度的定量测量

在"神光II"多束高功率激光装置上利用列阵透镜匀滑钕玻璃波长0.53μm的强激光幅照平面金(Au)靶时产生X射线,本文给出了X射线绝对转换效率ξx。研究了多束倍频激光叠加驱动靶形成X射线背景光源辐射金M壳层1.8—3.1Kev带谱的特性,获得了不同激光功率密度及不同角度驱动靶面等几种条件下X射线能谱的定量测量结果和能谱分布。     

X射线二极管时间特性研究

研究X射线二极管(XRD)时间特性.XRD 是构成软X射线能谱仪的主要部件，它用于激光等离子体发射软X射线谱测量.实验利用激光聚变研究中心的200TW激光器(激光能量～6J，脉冲宽度～30fs)打金箔靶产生的X射线发射谱,用滤片(Al)-XRD探测系统测量，探测信号由高频电缆(SUJ-50-10)传输和宽带示波器(TDS694C和TDS6604B)记录.实验数据进行了线性拟合和比对分析. 关键词： X射线二极管 时间特性 软X射线能谱仪 数据处理     

腔靶X射线辐射特性实验研究

在上海“神光”装置上,对柱形腔靶X射线辐射的温度、光谱以及时间特性进行了实验研究,得到内爆区轴向温度随空间位置的变化特征。观测到腔内激光直接烧蚀靶物质产生的第一次X射线辐射和等离子体运动、汇聚形成的第二次X射线辐射,两次辐射的时间间隔为1.2ns。通过测量源区和内爆区X射线辐射空间能谱结构,结果表明源区X射线辐射能谱是非平衡的,而内爆区X射线辐射能谱近似为Planck谱。 关键词：     

神光Ⅱ黑腔等离子体时间分辨的电子温度诊断

在神光Ⅱ强激光装置上,用条纹晶体谱仪对埋点于黑腔靶内壁上的双示踪Ti和Cr材料的激光等离子体高离化态离子发射的X射线谱线进行实验测量,获得超高时间分辨的X射线细致结构谱线。用碰撞辐射模型计算了非局域热动平衡的等离子体布居数,组态平均速率系数由一级微扰理论计算,电子波函数由Hartree-Fock Slater自洽场方法计算,给出了Ti和Cr激光等离子体在电子密度为1019~1022cm-3范围内的He-α线强比与电子温度的关系曲线。采用等电子X射线谱线法,获得了黑腔靶激光等离子体冕区的电子温度随激光脉冲加热从低温到高温、然后缓慢下降的演化过程,其峰值达到2.05 keV。     

1.053μm激光辐照金箔靶发射X射线能谱的实验研究

在“星光-Ⅱ”单束高功率激光装置上利用束匀滑的钕玻璃基频激光辐照不同厚度的金箔靶,测量了金箔靶前向和背向的X射线能谱、X射线辐射能量角分布及X射线能谱时间变化过程,研究了金箔靶中激光烧蚀及辐射烧蚀过程;获得了不同厚度金箔、不同激光功率密度及不同角度等几种条件下其前后向X射线能谱的定量测量结果,同时从不同厚度的金箔背侧X射线能谱时间过程观察到明显的辐射热波时间延迟. 关键词： 金箔靶 X射线能谱 辐射烧蚀 辐射热波     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.     

A stereo matching algorithm using multi-peak candidate matches and geometric constraints

Gray cross correlation matching technique is adopted to extract candidate matches with gray cross correla- tion coefficients less than some certain range of maximal correlation coefficient called multi-peak candidate matches. Multi-peak candidates are extracted corresponding to three closest feature points at first. The corresponding multi-peak candidate matches are used to construct the model polygon. Correspondence is determined based on the local geometric relations between the three feature points and the multi-peak candidates. The disparity test and the global consistency checkout are applied to eliminate the remaining ambiguous matches that are not removed by the local geometric relational test. Experimental results show that the proposed algorithm is feasible and accurate.