原子转移自由基聚合合成甲基丙烯酸丁酯与丙烯酸全氟烷基乙酯两嵌段共聚物及其性能的研究

通过原子转移聚合合成了大分子引发剂PBMA Br及系列含氟两嵌段共聚物P(BMA b FAEM) ,并利用1 H NMR、F EA、GPC、FTIR对其结构进行了表征 .所合成的含氟嵌段共聚物膜具有低临界表面张力 .本文通过接触角的测定研究了含氟两嵌段共聚物的憎水、憎油性能与共聚物的含氟量 ,热处理温度 ,热处理时间的关系 ,结果表明含氟嵌段PFAEM具有向空气 聚合物界面富集的倾向 ,在共聚物中引入含氟嵌段可以明显提高共聚物的憎水、憎油性 .当含氟嵌段达 7 6wt%时 ,临界表面张力 (γc =18 7mN m)已与聚四氟乙烯相当 (γc=18 5mN m) ,显示出明显的低表面能特征     

Surface Properties of Fluorinated Acrylate Polymer Latex Films

The surface chemical compositions of fluorinated latex films and the dynamic contact angles of water were determined using X-ray photoelectron spectroscopy (XPS) and a Kruss interface tension measurement, respectively. The surface tensions of the films were calculated by the equation of state approach using the dynamic contact angles, and the effect of temperature on the wetting behavior of these films was investigated. It was shown that the F 1s signal intensity from the outermost surface of these fluorinated latex films was stronger than that from the interior surface of the film and that the surface tension showed a linear decrease with the increase of density of fluorine atoms on the latex film surface to a certain extent. The surface tension rapidly decreased with the increase of fluorinated lateral chains (Rf) content in the copolymer with longer Rf (carbon atom number n>6). The water receding contact angles (θr) on the latex films sharply decreased with the increase of n value, then leveled off nearly at n=10, and remained almost unchanged when n>10. In addition, θr increased more remarkably with the increase of F content in the poly (protonated acrylate- co-fluorinated acrylate) with short hydrocarbon side chains. The water wetting ability of the fluorinate latex films became slightly better only when temperature was more than 40°C.     

Study of the advancing and receding contact angles: liquid sorption as a cause of contact angle hysteresis

Two types of experiments were used to study the behavior of both advancing and receding contact angles, namely the dynamic one-cycle contact angle (DOCA) and the dynamic cycling contact angle (DCCA) experiments. For the preliminary study, DOCA measurements of different liquids on different solids were performed using an automated axisymmetric drop shape analysis-profile (ADSA-P). From these experimental results, four patterns of receding contact angle were observed: (1) time-dependent receding contact angle; (2) constant receding contact angle; (3) 'stick/slip'; (4) no receding contact angle. For the purpose of illustration, results from four different solid surfaces are shown. These solids are: FC-732-coated surface; poly(methyl methacrylate/n-butyl methacrylate) [P(MMA/nBMA)]; poly(lactic acid) (DL-PLA); and poly(lactic/glycolic acid) 50/50 (DL-PLGA 50/50). Since most of the surfaces in our studies exhibit time dependence in the receding contact angle, a more extended study was conducted using only FC-732-coated surfaces to better understand the possible causes of decreasing receding contact angle and contact angle hysteresis. Contact angle measurements of 21 liquids from two homologous series (i.e. n-alkanes and 1-alcohols) and octamethylcyclotetrasiloxane (OCMTS) on FC-732-coated surfaces were performed. It is apparent that the contact angle hysteresis decreases with the chain length of the liquid. It was found that the receding contact angle equals the advancing angle when the alkane molecules are infinitely large. These results strongly suggest that the chain length and size of the liquid molecule could contribute to contact angle hysteresis phenomena. Furthermore, DCCA measurements of six liquids from the two homologous series on FC-732-coated surfaces were performed. With these experimental results, one can construe that the time dependence of contact angle hysteresis on relatively smooth and homogeneous surfaces is mainly caused by liquid retention/sorption. The results also suggested that the contact angle hysteresis will eventually approach a steady state, where the rate of liquid retention-evaporation or sorption process would balance out each other. If the existence of contact angle hysteresis can be attributed to liquid sorption/retention, one should only use the advancing contact angles (measured on a dry surface) in conjunction with Young's equation for surface energetic calculations.     

Wettability of biodegradable surfaces

The study of the interfacial characteristics of biodegradable polymers/copolymers is of importance from the point of view of both surface science and pharmaceutical/cosmetic applications. Films formed from biodegradable polymers allow systematic wettability studies on surfaces with a wide range of copolymer (chemical) compositions. The possibility of interchanging these drug carrier polymers, if their wetting characteristics are similar, could be beneficial to diverse applications. Low-rate dynamic contact angles on films (solvent cast on polar substrates, i.e. on silicon wafer) of poly(lactic acid), and its copolymers with poly(glycolic acid), (with four different copolymer ratios of 85/15, 75/25, 65/35 and 50/50) were measured by axisymmetric drop shape analysis-profile (ADSA-P) with four liquids: water, formamide, 2,2′-thiodiethanol and 3-pyridylcarbinol. The solid surface tensions, γ_sv, were calculated from the advancing contact angles, θ_A. The surface topography of the polymer films was investigated by atomic force microscopy (AFM). The surface composition of the polymer layers was analyzed by X-ray photoelectron spectroscopy (XPS). The advancing contact angles were found to be independent of the composition of the copolymers, while the receding angles, θ_R, did decrease with increasing ratio of the polar component [poly(glycolic acid)] in the copolymers. The solid surface tensions calculated from the advancing contact angles of the liquids for all homo- and copolymers were the same within the error limit; the mean value being γ_sv=35.6 ± 0.2 mJ/m². The surface roughness, which was obtained from AFM images, increased with increasing poly(glycolic acid) ratio, without affecting the advancing contact angles. The constancy of γ_sv is attributed to the effect of the surface activity of the nonpolar segments of the polymer chains, which oriented to form the outermost layer of the film. This was confirmed by XPS analysis. Received: 06 November 2000 Accepted: 09 May 2001     

Bioinspired synthesis of superhydrophobic coatings

A superhydrophobic material prepared by precipitating calcium phosphate on TiO2 films under in vitro conditions is described. Crystalline calcium phosphate is very porous with octacalcium phosphate as the main phase. The films are made hydrophobic by the surface grafting of a perfluorophosphate surfactant (Zonyl FSE). The as-prepared coatings were strongly hydrophobic, with advancing contact angles exceeding 165 degrees and receding angles exceeding 150 degrees . The formation of the calcium phosphate layer is self-organizing, and the coating is easily functionalized. The material was characterized with dynamic contact angle measurements, SEM, XRD, and XPS. The strong water repellency is explained by the open porous morphology of the calcium phosphate coating together with the successful attachment of the hydrophobic function.     

Patterning on nonplanar substrates: flexible honeycomb films from a range of self-assembling star copolymers

The effect of glass transition temperature, Tg, on the self-assembly of "honeycomb" microstructures on nonplanar substrates was probed by the synthesis of a library of core cross-linked star polymers with different arm compositions. Star polymers based on poly(dimethyl siloxane), poly(ethyl acrylate), poly(methyl acrylate), poly(tert-butyl acrylate), and poly(methyl methacrylate) were synthesized by the "arm first" strategy using atom-transfer radical polymerization. Reaction conditions were optimized, and a series of high molecular weight star polymers were prepared in high yield. The glass transition temperature of the star polymers ranged from -123 to 100 degrees C which allowed the suitability for the formation of porous honeycomb-like films via the "breath figure" technique on nonplanar surfaces to be investigated. All star compositions successfully formed ordered films on flat surfaces. However, only star polymer compositions with a Tg below 48 degrees C could form homogeneous honeycomb coatings on the surface of nonplanar substrates.     

Line energy and the relation between advancing, receding, and young contact angles

The line energy associated with the triple phase contact line is a function of local surface defects (chemical and topographical); however, it can still be calculated from the advancing and receding contact angles to which those defects give rise. In this study an expression for the line energy associated with the triple phase contact line is developed. The expression relates the line energy to the drop volume, the interfacial energies, and the actual contact angle (be it advancing, receding, or in between). From the expression we can back calculate the equilibrium Young contact angle, theta0, as a function of the maximal advancing, thetaA, and minimal receding, thetaR, contact angles. To keep a certain maximal hysteresis between advancing and receding angles, different line energies are required depending on the three interfacial energies and the drop's volume V. We learn from the obtained expressions that the hysteresis is determined by some dimensionless parameter, K, which is some normalized line energy. The value of K required to keep a constant hysteresis (thetaA-thetaR) rises to infinity as we get closer to theta0 = 90 degrees.     

Facile method to fabricate raspberry-like particulate films for superhydrophobic surfaces

A facile method using layer-by-layer assembly of silica particles is proposed to prepare raspberry-like particulate films for the fabrication of superhydrophobic surfaces. Silica particles 0.5 microm in diameter were used to prepare a surface with a microscale roughness. Nanosized silica particles were then assembled on the particulate film to construct a finer structure on top of the coarse one. After surface modification with dodecyltrichlorosilane, the advancing and receding contact angles of water on the dual-sized structured surface were 169 and 165 degrees , respectively. The scale ratio of the micro/nano surface structure and the regularity of the particulate films on the superhydrophobic surface performance are discussed.     

Mineral matter distribution on coal surface and its effect on coal wettability

Coal is an organic sedimentary rock composed of organic macerals and mineral matter. As it is demonstrated in this paper the discrete mineralogical nature of coal largely influences the wetting of the coal surface by water. Both advancing and receding contact angles were measured using the captive-bubble technique with an automatic bubble shape analysis software. The distribution and amount of mineral inclusions on the coal surface were determined by scanning electron microscopy and examined using the image analysis system. To determine the amount and size distribution of mineral grains, the coal surface layer, on which the contact angles were measured, was separated from the larger piece used in the measurements by microslicing. The separated surface layer was subjected to a low-temperature ashing followed by particle size analysis. As expected, a significant scatter of contact angle values was obtained for the same coal samples. Increasing the amount of mineral matter on the coal surface reduced the value of both advancing and receding contact angles. Also, the scatter of contact angle values increased with the increasing mineral matter content from about 1 to 50 wt%. The results reveal that an important factor in analysis of contact angle variation on coal surfaces is the size of the hydrophilic mineral inclusions. Both the advancing and the receding contact angles decrease with increasing size of the mineral grains. Additionally, the scatter of contact angle values increase with increasing size of the mineral matter grains. Finally, the results of fractal dimension analysis of mineral matter grains distributed over the coal surface indicate that there is no significant effect from the shape of hydrophilic mineral inclusions on both advancing and receding contact angles.     

Fabrication of shape-controllable polyaniline micro/nanostructures on organic polymer surfaces: obtaining spherical particles, wires, and ribbons

A novel strategy was developed in order to prepare various micro/nanostructured polyanilines (PANI) on polymer substrates. The strategy involved two main steps, i.e., a grafting polymerization of acrylate acid (AA) onto the surface of a polypropylene (PP) film and subsequently an oxidative polymerization of aniline on the grafted surface. By tuning the conformation of the surface-grafted poly acrylate acid (PAA) brushes, as well as the ratio of AA to aniline, the shape of the PANIs fixated onto the surfaces of the polymer substrate could be controlled to go from spherical particles to nanowires and eventually to nanoribbons. In these structures, the PAA brushes not only acted as templates but also as dopants of PANI, and thereby, the nanostructured PANIs could be strongly bonded with the substrate. In addition, the surface of the PP films grafted with polyaniline nanowires and nanoribbons displayed superhydrophobicity with contact angles for water of approxiamtely 145 and 151 degrees , respectively.     

Comparison of surface confined ATRP and SET‐LRP syntheses for a series of amino (meth)acrylate polymer brushes on silicon substrates

A series of poly(amino (meth)acrylate) brushes, poly(2‐(dimethylamino)ethyl methacrylate) (PDMAEMA), poly(2‐(diethylamino)ethyl methacrylate) (PDEAEMA), poly(2‐(dimethylamino)ethyl acrylate) (PDMAEA), poly(2‐(tert‐butylamino)ethyl methacrylate) (PTBAEMA), has been synthesized via surface‐confined controlled/living radical polymerizations using surface‐confined initiator from silane self‐assembled monolayers (SAMs) on silicon (Si) wafer substrates. Chemical methods and efficacies for two types of living radical polymerization, atom transfer radical (ATRP) and single electron transfer (SET‐LRP), are described and contrasted for the surface confined polymerization of poly(amino (meth)acrylate)s. Effects of solvent, catalyst/ligand system, and temperature on polymerization success were examined. Chemical compositions after each reaction step were characterized with FTIR spectroscopy, contact angle goniometry, and X‐ray photoelectron spectroscopy while the SAM and polymer brush thicknesses were measured with spectroscopic ellipsometry. For the first time, this study demonstrates successful surface‐confined polymerization of a series of poly(amine (meth)acrylate) brushes from Si‐SAM substrates using a copper metal electron donor catalyst. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 6552–6560, 2009     

Plasma Treatment of Polymers to Generate Stable,Hydrophobic Surfaces

Tailoring of polymers for multifaceted applications is an increasing field, whereby most often the surface properties must be adjusted. Therefore, the coating of common polymers by plasma polymerization is a promising way to modify the surface and meet the demands. Beside the tuning of the required surface properties, good adhesion and stability of the films is essential. This work investigates the plasma deposition of pp-HMDSO films on PC and PC/ABS to generate stable, hydrophobic surfaces. By examining the plasma conditions—deposition rate, energy range, and surface topography—ultrathin, stable films with advancing contact angles up to 110° and receding angles exceeding 90° can be designed. Storage of the siloxane films for 1 year in air at ambient conditions exhibits almost no aging. Thus, these films are superior to fluorocarbon films deposited for comparison.     

A general approach to controlling the surface composition of poly(ethylene oxide)-based block copolymers for antifouling coatings

To control the surface properties of a polystyrene-block-poly(ethylene oxide) diblock copolymer, perfluorinated chemical moieties were specifically incorporated into the block copolymer backbone. A polystyrene-block-poly[(ethylene oxide)-stat-(allyl glycidyl ether)] [PS-b-P(EO-stat-AGE)] statistical diblock terpolymer was synthesized with varying incorporations of allyl glycidyl ether (AGE) in the poly(ethylene oxide) block from 0 to 17 mol %. The pendant alkenes of the AGE repeat units were subsequently functionalized by thiol-ene chemistry with 1H,1H,2H,2H-perfluorooctanethiol, yielding fluorocarbon-functionalized AGE (fAGE) repeat units. (1)H NMR spectroscopy and size-exclusion chromatography indicated well-defined structures with complete functionalization of the pendant alkenes. The surfaces of the polymer films were characterized after spray coating by X-ray photoelectron spectroscopy (XPS) and near-edge X-ray absorption fine structure spectroscopy (NEXAFS), showing that the P(EO-stat-fAGE) block starts to compete with polystyrene to populate the surface after only 1 mol % incorporation of fAGE. Increasing the incorporation of fAGE led to an increased amount of perfluorocarbons on the surface and a decrease in the concentration of PS. At a fAGE incorporation of 8 mol %, PS was not detected at the surface, as measured by NEXAFS spectroscopy. Water contact angles measured by the captive-air-bubble technique showed the underwater surfaces to be dynamic, with advancing and receding contact angles varying by >20°. Protein adsorption studies demonstrated that the fluorinated surfaces effectively prevent nonspecific binding of proteins relative to an unmodified PS-b-PEO diblock copolymer. In biological systems, settlement of spores of the green macroalga Ulva was significantly lower for the fAGE-incorporated polymers compared to the unmodified diblock and a polydimethylsiloxane elastomer standard. Furthermore, the attachment strength of sporelings (young plants) of Ulva was also reduced for the fAGE-containing polymers, affirming their potential as fouling-release coatings.     

Fouling-release coatings prepared from alpha,omega-dihydroxypoly(dimethylsiloxane) cross-linked with (heptadecafluoro-1,1,2,2-tetrahydrodecyl)triethoxysilane

Surface properties of pristine and water-aged polymeric films made of alpha,omega-dihydroxypoly(dimethylsiloxane) (PDMS) cross-linked with (heptadecafluoro-1,1,2,2-tetrahydrodecyl)triethoxysilane (FTEOS17) or tetraethoxysilane (TEOS) were investigated. The FTEOS17-cured coatings showed stable advancing and receding contact angles over a period of 3 months of water exposure, compared to a 70 degrees decrease in receding contact angle for the TEOS-cured coatings. After immersion in water, hydroxyl groups were detected on the TEOS-cured coatings with attenuated total reflection infrared spectroscopy (ATR-FT/IR). Tapping-mode atomic force microscopy (TM-AFM) on pristine FTEOS17-cured coatings showed surfaces topologies ranging from smooth and featureless to topologically complex, depending on FTEOS17 concentration. The fluorinated coatings showed a stable surface morphology after water immersion, which we believe is due to the formation of a fluorinated siliceous phase that prevented the surface reconstruction, water penetration, and hydrolysis. The smooth pristine TEOS-cured coatings showed an increased roughness with cracks and erosion pits present on the surface after water immersion.     

A perfectly hydrophobic surface (thetaA/thetaR = 180 degrees /180 degrees)

A perfectly hydrophobic surface with both advancing and receding water contact angles of 180 degrees was prepared using a facile method on a silicon wafer. Phase separation of a toluene-swollen covalently attached methylsilicone results in a nanoscale network structure that is responsible for the superhydrophobicity. A method for testing extreme hydrophobicity was devised to distinguish between surfaces exhibiting contact angles of 180 and 179 degrees .     

Modeling contact angle hysteresis of a liquid droplet sitting on a cosine wave-like pattern surface

A liquid droplet sitting on a hydrophobic surface with a cosine wave-like square-array pattern in the Wenzel state is simulated by using the Surface Evolver to determine the contact angle. For a fixed drop volume, multiple metastable states are obtained at two different surface roughnesses. Unusual and non-circular shape of the three-phase contact line of a liquid droplet sitting on the model surface is observed due to corrugation and distortion of the contact line by structure of the roughness. The contact angle varies along the contact line for each metastable state. The maximum and minimum contact angles among the multiple metastable states at a fixed viewing angle correspond to the advancing and the receding contact angles, respectively. It is interesting to observe that the advancing/receding contact angles (and contact angle hysteresis) are a function of viewing angle. In addition, the receding (or advancing) contact angles at different viewing angles are determined at different metastable states. The contact angle of minimum energy among the multiple metastable states is defined as the most stable (equilibrium) contact angle. The Wenzel model is not able to describe the contact angle along the three-phase contact line. The contact angle hysteresis at different drop volumes is determined. The number of the metastable states increases with increasing drop volume. Drop volume effect on the contact angles is also discussed.     

Thermoresponsive poly(N-isopropylacrylamide) copolymers: contact angles and surface energies of polymer films

Surface properties of poly(N-isopropylacrylamide) (PNIPAM) copolymer films were studied by contact angle measurements and optical and atomic force microscopy. We prepared a series of copolymers of N-isopropylacrylamide with N-tert-butylacrylamide (NtBA) in order of increasing hydrophobicity. The measurements of the advancing contact angle of water at 37 degrees C were hampered by the observation of a distinct stick/slip pattern on all polymers in the series with the exception of poly(NtBA) (PNtBA). We attributed this behavior to the film deformation by the vertical component of liquid surface tension leading to the pinning of the moving contact line. This was confirmed by the observation of a ridge formed at the pinned contact line by optical microscopy. However, meaningful contact (without the stick/slip pattern and with a time-independent advancing contact angle) angles for this thermoresponsive polymer series could be obtained with carefully selected organic liquids. We used the Li and Neumann equation of state to calculate the surface energy and contact angles of water for all polymers in the series of copolymers and van Oss, Chaudhury, and Good (vOCG) acid-base theory for PNtBA. The surface energies of the thermoresponsive polymers were in the range of 38.9 mJ/m2 (PNIPAM) to 31 mJ/m2 (PNtBA) from the equation of state approach. The surface energy of PNtBA calculated using vOCG theory was 29.0 mJ/m2. The calculated contact angle for PNIPAM (74.5 +/- 0.2 degrees ) is compared with previously reported contact angles obtained for PNIPAM-modified surfaces.     

Roughness assessment and wetting behavior of fluorocarbon surfaces

The wetting behavior of fluorocarbon materials has been studied with the aim of assessing the influence of the surface chemical composition and surface roughness on the water advancing and receding contact angles. Diamond like carbon and two fluorocarbon materials with different fluorine content have been prepared by plasma enhanced chemical vapor deposition and characterized by X-ray photoemission, Raman and FT-IR spectroscopies. Very rough surfaces have been obtained by deposition of thin films of these materials on polymer substrates previously subjected to plasma etching to increase their roughness. A direct correlation has been found between roughness and water contact angles while a superhydrophobic behavior (i.e., water contact angles higher than 150° and relatively low adhesion energy) was found for the films with the highest fluorine content deposited on very rough substrates. A critical evaluation of the methods currently used to assess the roughness of these surfaces by atomic force microscopy (AFM) has evidenced that calculated RMS roughness values and actual surface areas are quite dependent on both the scale of observation and image resolution. A critical discussion is carried out about the application of the Wenzel model to account for the wetting behavior of this type of surfaces.     

Controlled Synthesis,Characterization and Application of Novel Functional Fluorinated Polymer By Metal-Free Anionic Polymerization

A well-defined block polymer, di-n-butyl ester terminated poly(2,2,3,4,4,4-hexafluorobutyl methacrylate (BTHFMA), was synthesized by the metal-free anionic polymerization. The tetrabutylammonium salt of di-n-butyl malonate was served as functional carbanionic initiator for the anionic polymerization of 2,2,3,4,4,4-hexafluorobutyl methacrylate in a controlled ‘living’ manner for the first time at ambient temperature. The chemical structure of this product was characterized by FT-IR, ¹H-NMR, and ¹³C-NMR. Gel permeation chromatography (GPC) results showed that the molecular weight of BTHFMA ranged from 1025 to 6582 and the molecular weight distributions were fairly narrow (Mw/Mn = 1.12–1.16). By blending the poly(methyl methacrylate-co-butyl acrylate) [P(MMA-co-BA)] with BTHFMA, we minimized the amount of the BTHFMA used while achieving a hydrophobic surface. The surface properties and compositions of the [P(MMA-co-BA)]/BTHFMA blend films were studied by contact angle and X-ray photoelectron spectroscopy (XPS). The results demonstrated that the 5 wt% blends of BTHFMA could obviously increase hydrophobic ability of the blend with a high water contact angle (98.2^o) and low surface energy (24.2mN/m). XPS results indicated the fluorine mass content of the surface of the 5 wt% blend was up to 26.6%, which suggested BTHFMA enriched on the surface of the blend.     

The suspension�Cemulsion combined polymerization of fluorinated acrylic monomer and the fluorinated latex film surface properties

The perfluoroacrylate-containing copolymer composite particles were fabricated by suspension?Cemulsion combined polymerization (SECP). The features and formation mechanism of resulting polymer particles in SECP were studied. The fluorinated latexes with better stability and those fluorinated films with high surface fluorine content were prepared by SECP using fluorine-free surfactants as an emulsifying agent, and the surface natures of the fluorinated films were characterized. It was found that P(MMA?CBA) latex particles gradually coagulated with P(PFA?CBA) particles after adding emulsion polymerization constituents at the midstage of the suspension polymerization, and fluorinated composite particles with core?Cshell structure and larger size were obtained. The fluorine contents either on the film surface or in the bulk of the film and the films from SECP are higher than those from miniemulsion polymerization at high PFA feed ratio (more than 20?wt.%). The model of PFA?CMMA?CBA SECP was proposed according to the variations of particle features of the composite particles.