Structural radial heterogeneity of a silica-based wide-bore monolithic column

The radial distribution of the main characteristics (elution time and standard deviation) of the elution profiles of a flat injected band recorded at the exit of a monolithic column were determined. These distributions provide the radial distributions of the average mobile phase velocity, the elution time and the maximum height of the peak of an analyte, the column efficiency and the analyte concentration. The band profiles were measured at the exit of a 10-mm i.d., 100-mm long silica-based monolithic column. An on-column local electrochemical amperometric detector allowed the recording of the elution profiles at different spatial positions throughout the column cross-section. The local spatial distribution of the mobile phase velocity does not follow a piston-flow behavior but exhibits radial heterogeneity. The local efficiency near the wall is lower than that near the column center. The radial distribution of the maximum concentration of the peaks varies throughout the column exit section, partially due to the radial variations of the column efficiency. These results might explain the rather large value of the A term of the Van Deemter or the Knox equations reported previously for monolithic columns.     

Solventless injecction for packed column supercritical fluid chromatography

The adverse effects of injection solvent strength on microbore packed column SFC band broadening are demonstrated and a solventless injection system that eliminates these effects is introduced. The injection system removes solvent in a GC-like manner using a retention gap and an on-column capillary GC syringe. The analyte is delivered to the analytical column in a solvent-free plug of supercritical fluid mobile phase.     

Density gradients in packed columns: I. Effects of density gradients on retention and separation speed

Density gradients in packed capillary columns operating under the extreme pressure drops typical for solvating gas chromatography were investigated by on-column spectroscopic measurements and compared to a theoretical model. Laser-induced fluorescence was used to follow the elution of various analytes, and Raman spectroscopy was used to measure the density of the mobile phase, each with respect to column position. Mobile phase linear velocity initially increases gradually, and then rises rapidly near the column outlet. High flow rates near the column outlet are offset by a loss of mobile phase solvating power which ultimately limits the speed of separation. These results represent an extreme case for illuminating factors affecting supercritical fluid separation techniques in general.     

Numerical modeling of the elution peak profiles of retained solutes in supercritical fluid chromatography

In supercritical fluid chromatography (SFC), the significant expansion of the mobile phase along the column causes the formation of axial and radial gradients of temperature. Due to these gradients, the mobile phase density, its viscosity, its velocity, its diffusion coefficients, etc. are not constant throughout the column. This results in a nonuniform flow velocity distribution, itself causing a loss of column efficiency in certain cases, even at low flow rates, as they do in HPLC. At high flow rates, an important deformation of the elution profiles of the sample components may occur. The model previously used to account satisfactorily for the retention of an unsorbed solute in SFC is applied to the modeling of the elution peak profiles of retained compounds. The numerical solution of the combined heat and mass balance equations provides the temperature and the pressure profiles inside the column and values of the retention time and the band profiles of retained compounds that are in excellent agreement with independent experimental data for large value of mobile phase reduced density. At low reduced densities, the band profiles can strongly depend on the column axial distribution of porosity.     

Band broadening effects in capillary column recycle gas chromatography with valves

Sources leading to band broadening and peak distortion have been studied in a capillary column recycle system, based on a commercial microvalve. The ferrule system was a major contributor to band broadening. It was found that the quality of connections is very critical but the internal volume of the valve is not important. The pressure pulses resulting from each switching operation produced some band broadening with substances that had just been transferred through the valve but no adverse effects were noticed when they had travelled some distance into the column. Flow into valve cavities and through tees also produced a drop in efficiency. It is not clear whether this is solely due to problems in column connection or if changes in flow pattern also contribute. The activity of the valve toward polar substances was also assessed. No attempt was made to deactivate valve surfaces. The components of the Grob test mixture were almost unaffected but highly polar and acidic compounds such as nitrophenol showed severe losses. No evidence for catalysis was found.     

Direct coupling of size exclusion chromatography and mass spectrometry for the characterization of complex monoclonal antibody products

The present study describes the possibilities offered by an innovative bioinert size exclusion chromatography column for size variant characterization of complex monoclonal antibody products. This size exclusion chromatography column includes a novel column hardware surface. The column was prepared from metallic hardware components that were treated to have prototype hydrophilically modified hybrid organic–inorganic silica surfaces called hybrid surface technology. This provides a significant reduction in nondesired hydrophobic and electrostatic interactions that can occur between column and analyte when performing size exclusion chromatography analysis with volatile mobile phase. Compared to a reference stainless-steel column packed with the same batch of packing material, peak tailing, band broadening, and above all recovery of high molecular weight species were distinctly improved for all types of monoclonal antibody products. Based on our observations, we found that 50 mM ammonium acetate in water was a suitable mobile phase offering good compromise in terms of liquid chromatography performance and mass spectrometry sensitivity. In addition, method repeatability (intra- and interday relative standard deviations) on elution times and high molecular weight species peak areas were found to be excellent. By using this innovative size exclusion chromatography material, the low and high molecular weight species contained in various stressed and nonstressed monoclonal antibody products were successfully characterized with mass spectrometry detection.     

Dynamic chromatography: A stochastic approach

During the chromatographic separation process, analyte reactions are often observed leading to band broadening and/or elution of peak clusters. For many different chemical compounds the reaction can be reduced to a simple isomerisation kinetic scheme where elution is the result of adsorption–desorption on the surface stationary phase coupled with a flipping two-level reaction system. In this paper, the chromatographic peak shape for a reacting analyte is calculated in frequency domain when the reaction follows a simple reversible first order scheme. Both reaction and dynamic chromatographic systems have been considered. The derived solutions are expressed in closed form in the Fourier domain. Several limit solutions obtained under conditions of very slow and moderately fast kinetics are exploited. The effects of both kinetics rate constants and retention time on the chromatographic peak shape are singled out.     

Experimental study of band broadening and solute interferences in preparative supercritical fluid chromatography

The effect of the amount injected on the elution profile of a single solute was used to investigate the shape of the distribution isotherm in overloaded supercritical fluid chromatography. Subsequently, the role of competition between solutes when the column is overloaded with a binary mixture was studied. The band broadening pattern is explained by the difference between the solubilities of the solutes in the supercritical fluid mobile phase.     

The obstruction factor in size-exclusion chromatography. 1. The intraparticle obstruction factor

We report the first of a series of studies on the obstruction factor γ in size-exclusion chromatography (SEC). Here, using narrow dispersity polymer standards we examine how the intraparticle obstruction factor γ(p) depends individually on a number of analyte properties, column characteristics, and user-defined parameters. Far from being constant, γ(p) is seen to vary with analyte molar mass and solvent, as well as with the pore size and particle size of the column packing material, sometimes in seemingly counterintuitive manner. Over the limited temperature range accessible to our equipment, however, no statistically significant change in γ(p) with temperature was discovered. The results presented should be applicable to forms of packed column chromatography other than SEC. The latter technique, however, presents a convenient test bed for quantitative determination of the obstruction factor, due to minimized sorptive mass transfer and longitudinal diffusion contributions to band broadening in most forms of SEC.     

Feasibility of ultra high performance supercritical neat carbon dioxide chromatography at conventional pressures

The implementation of columns packed with sub-2 μm particles in supercritical fluid chromatography (SFC) is described using neat carbon dioxide as the mobile phase. A conventional supercritical fluid chromatograph was slightly modified to reduce extra column band broadening. Performances of a column packed with 1.8 μm C18-bonded silica particles in SFC using neat carbon dioxide as the mobile phase were compared with results obtained in ultra high performance liquid chromatography (UHPLC) using a dedicated chromatograph. As expected and usual in SFC, higher linear velocities than in UHPLC must be applied in order to reach optimal efficiency owing to higher diffusion coefficient of solutes in the mobile phase; similar numbers of theoretical plates were obtained with both techniques. Very fast separations of hydrocarbons are presented using two different alkyl-bonded silica columns.     

Column radial homogeneity in high-performance liquid chromatography

The radial distribution of analyte molecules within an elution band in HPLC was determined by local, on-column, fluorescence detection at the column outlet. Several optical fiber assemblies were implanted in the exit frit at different points over the column cross-section and the fluorescence of a laser-dye analyte was measured. The individual elements of a diode array were used as independent detectors. The distribution of the mobile phase velocity across the column was measured for a number of standard size analytical HPLC columns of different efficiencies, operated at different mobile phase linear velocities. The dependence of the column efficiency on these profiles is discussed.     

Faster axial band dispersion in a monolithic silica column than in a particle-packed column

The contribution of molecular diffusion to peak broadening was studied in a reversed-phase HPLC system, consisting of a monolithic silica C18 column and methanol-water mobile phase. Study on the band broadening effect of holding a solute in a column or elution at very low linear velocity of mobile phase allowed facile determination of the contribution of the molecular diffusion term. Less obstruction against molecular diffusion, or the faster axial band dispersion in a monolithic silica column than in a particle-packed column, was found both in mobile phase and in stationary phase.     

Direct coupling of capillary electrophoresis and nuclear magnetic resonance spectroscopy for the identification of a dinucleotide

Summary In this paper, a general peak capacity expression was evaluated using columns containing various packing materials under solvating gas chromatography (SGC) conditions. Differing from column efficiency, peak capacity can describe both separation capability and speed when introducing the dead time into the peak capacity expression. Various factors that influence peak capacity in SGC are described, including particle pore size, chemical surface modification, particle size, column length, temperature, and pressure.     

Numerical modeling of elution peak profiles in supercritical fluid chromatography. Part I—Elution of an unretained tracer

When chromatography is carried out with high-density carbon dioxide as the main component of the mobile phase (a method generally known as “supercritical fluid chromatography” or SFC), the required pressure gradient along the column is moderate. However, this mobile phase is highly compressible and, under certain experimental conditions, its density may decrease significantly along the column. Such an expansion absorbs heat, cooling the column, which absorbs heat from the outside. The resulting heat transfer causes the formation of axial and radial gradients of temperature that may become large under certain conditions. Due to these gradients, the mobile phase velocity and most physico-chemical parameters of the system (viscosity, diffusion coefficients, etc.) are no longer constant throughout the column, resulting in a loss of column efficiency, even at low flow rates. At high flow rates and in serious cases, systematic variations of the retention factors and the separation factors with increasing flow rates and important deformations of the elution profiles of all sample components may occur. The model previously used to account satisfactorily for the effects of the viscous friction heating of the mobile phase in HPLC is adapted here to account for the expansion cooling of the mobile phase in SFC and is applied to the modeling of the elution peak profiles of an unretained compound in SFC. The numerical solution of the combined heat and mass balance equations provides temperature and pressure profiles inside the column, and values of the retention time and efficiency for elution of this unretained compound that are in excellent agreement with independent experimental data.     

Dual injector solvent elution and focussing technique for the on-line analysis of solid-phase extraction cartridges in HPLC

Summary A new dual injector solvent focussing and elution technique developed for high-performance liquid chromatography (HPLC) greatly improves chromatographic efficiency for the on-line analysis of C₁₈ solid-phase extraction (SPE) cartridges. Solutions containing three benzene homologs were used to characterize the dual injector analysis technique and to compare the chromatographic efficiency of this method with conventional SPE analysis methods. Sampling was performed off-line using a glass precolumn cartridge (3 mm i.d. × 30 mm) packed with 15–35 μm C₁₈ silica. On-line cartridge analysis was achieved with two injection valves in either serial or parallel configuration. The injection loop of the first valve contains the eluting solvent, and the cartridge holder is connected in place of the injection loop of the second valve. When an injection is made, both valves are turned to the inject position, and the solvent plug is forced through the cartridge, focussing the analyte at the solvent front as it elutes the cartridge. Solvent focussing at the head of the column, resulting from preconditioning of the column with a small plug of water during injection, further minimizes the variance of the injection plug and improves the chromatographic efficiency. The technique has potential applications to environmental and biological fluid analysis where analyte preconcentration and resolution from the sample matrix components may be difficult with current SPE methods.     

Fundamental chromatographic equations designed for columns packed with very fine particles and operated at very high pressures. Applications to the prediction of elution times and the column efficiencies

The wall temperatures of three Acquity-BEH-C18columns (2.1 mm x 50, 100, and 150 mm) and the temperature of the incoming eluent were maintained constant at 289 K, using a circulating water heat exchanger. The retention times and the band broadening of naphtho[2,3-a]pyrene were measured for each column as a function of the flow rate applied. Pure acetonitrile was used as the eluent. The flow rate dependence of neither elution volumes nor bandwidths can be accounted for by classical models of retention and HETP, respectively, since these models assume columns to be isothermal. Because the heat generated by friction of the eluent against the column bed increases with increasing flow rate, the column bed cannot remain isothermal at high flow rates. This heat is evacuated radially and/or longitudinally by convection, conduction, and radiation. Radial and axial temperature gradients are formed, which are maximum and minimum, respectively, when the temperature of the column wall is kept uniform and constant. The retention times that we measured match well with the values predicted based on the temperature distribution along and across the column, which we calculated and on the temperature dependence of the retention for the same column operated isothermally (i.e., at very low flow rate). The rate of band spreading varies along non-isothermal columns, so the HETP can only be defined locally. It is a function of the axial coordinate. A new contribution is needed to account for the radial thermal heterogeneity of the column, hence the radial distribution of the flow velocities, which warps the elution band. A new model, based on the general dispersion theory of Aris, allows a successful prediction of the unusually large bandwidths observed with columns packed with fine particles, operated at high flow rates, hence high inlet pressures.     

Experimental study of the depth influence on the band broadening effect in a cyclo-olefin polymer column containing an array of ordered pillars

An experimental study of a micromachined non-porous pillar array column performance under non-retentive conditions is presented. The same pillar structure has been fabricated in cyclo-olefin polymer (COP) chips with three different depths via hot embossing and pressure-assisted thermal bonding. The influence of the depth on the band broadening along with the already known contribution arising from the top and bottom cover plates has been studied. The experimental results exhibit reduced plate heights as low as 0.2, which are in agreement with the previous experimental work. Moreover, the constant values of the reduced Van Deemter expression are also in accordance with the previous studies. A more exhaustive study of the C-term band broadening is also presented, showing that comparing the space between the pillars with different open tubular rectangular channels offers a good estimation of the C-term band broadening that is obtained experimentally. These experimental results, hence, confirm that micromachined pillar array columns fabricated in COP can achieve the same performance as the ones fabricated in silicon for the presently studied pillar channel design.     

Practical method for the definition of chromatographic peak parameters in preparative liquid chromatography

A practical method was established for the definition of chromatographic parameters in preparative liquid chromatography. The parameters contained both the peak broadening level under different amounts of sample loading and the concentration distribution of the target compound in the elution. The parameters of the peak broadening level were defined and expressed as a matrix, which consisted of sample loading, the forward broadening and the backward broadening levels. The concentration distribution of the target compound was described by the heat map of the elution profile. The most suitable stationary phase should exhibit the narrower peak broadening and it was best to broaden to both sides to compare to the peak under analytical conditions. Besides, the concentration distribution of the target compounds should be focused on the middle of the elution. The guiding principles were validated by purification of amitriptyline from the mixture of desipramine and amitriptyline. On the selected column, when the content of the impurity desipramine was lower than 0.1%, the recovery of target compound was much higher than the other columns even when the sample loading was as high as 8.03 mg/cm³. The parameters and methods could be used for the evaluation and selection of stationary phases in preparative chromatography.     

Efficiency losses caused by gradients in solute velocity in packed column supercritical fluid chromatography

Summary Under a few sets of extreme conditions, retention gradients caused losses in apparent efficiency in packed column SFC. Under most practical chromatographic conditions no such losses occurred. The efficiency of five columns were measured both individually and connected in series. Under most conditions, no loss occurred. Under a few sets of conditions, the apparent efficiency of the five columns connected in series was as much as 66 % lower than the sum of the efficiencies of the individual columns measured under the same conditions. To observe a loss, the local retention near the column outlet must be unrealistically high and a steep non-linear change in retention is required. Under some sets of conditions, an approximate form of a recently proposed theory predicted losses similar to those observed.     

Modeling of thermal processes in high pressure liquid chromatography: I. Low pressure onset of thermal heterogeneity

Heat due to viscous friction is generated in chromatographic columns. When these columns are operated at high flow rates, under a high inlet pressure, this heat causes the formation of significant axial and radial temperature gradients. Consequently, these columns become heterogeneous and several physico-chemical parameters, including the retention factors and the parameters of the mass transfer kinetics of analytes are no longer constant along and across the columns. A robust modeling of the distributions of the physico-chemical parameters allows the analysis of the impact of the heat generated on column performance. We developed a new model of the coupled heat and mass transfers in chromatographic columns, calculated the axial and radial temperature distributions in a column, and derived the distributions of the viscosity and the density of the mobile phase, hence of the axial and radial mobile phase velocities. The coupling of the mass and the heat balances in chromatographic columns was used to model the migration of a compound band under linear conditions. This process yielded the elution band profiles of analytes, hence the column efficiency under two different sets of experimental conditions: (1) the column is operated under natural convection conditions; (2) the column is dipped in a stream of thermostated fluid. The calculated results show that the column efficiency is remarkably lower in the second than in the first case. The inconvenience of maintaining constant the temperature of the column wall (case 2) is that retention factors and mobile phase velocities vary much more significantly across the column than if the column is kept under natural convection conditions (case 1).