Detector supports: application to aliphatic amines in wastewater

Solid support assisted derivatization coupled to diffuse reflectance spectroscopy (DRS) was proposed and proved useful for the detection and quantification of aliphatic amines in water as an example. Dabsyl chloride (DBS), ninhydrin and sodium 1,2-naphtoquinone 4-sulphonate (NQS) were assayed as derivatization reagents. C₁₈ and SDB-XC disks and C₁₈ cartridges were tested for amine retention and after that derivatization. The decrease of the orange colour of dabsyl chloride on SBD-XC disks produced by the formation of its derivative with methylamine in the support (10 min at 100 °C) allowed the selective determination of the amine at concentration level equal or higher than 0.5 mg L⁻¹. Ninhydrin can be used for methylamine, ethylamine, propylamine, butylamine and pentylamine (between 5 and 15 mg L⁻¹) by measuring the diffuse reflectance produced by the brown derivative formed in C₁₈ extraction disks after 15 min at 100 °C. NQS and C₁₈ SPE columns can be also employed to estimate amines, but the detection limits were higher than those provided by DBS and Ninhydrin, around 10 mg L⁻¹. As an example, found concentration of methylamine or total amines (expressed as -NH₂-N mg L⁻¹) in a wastewater sample is given employing dabsyl chloride or ninhydrin reagents, respectively with satisfactory results.     

Determination of linear aliphatic aldehydes in heavy metal containing waters by high-performance liquid chromatography using 2,4-dinitrophenylhydrazine derivatization

A simple and sensitive method is described for the determination of picomolar amounts of C₁–C₉ linear aliphatic aldehydes in waters containing heavy metal ions. In this method, aldehydes were first derivatized with 2,4-dinitrophenylhydrazine (DNPH) at optimized pH 1.8 for 30 min and analyzed by HPLC with UV detector at 365 nm. Factors affecting the derivatization reaction of aldehydes and DNPH were investigated. Cupric ion, an example of heavy metals, is a common oxidative reagent, which may oxidize DNPH and greatly interfere with the determination of aldehydes. EDTA was used to effectively mask the interferences by heavy metal ions. The method detection limits for direct injection of derivatized most aldehydes except formaldehyde were of the order of 7–28 nM. The detection limit can be further lowered by using off-line C₁₈ adsorption cartridge enrichment. The recoveries of C₁–C₉ aldehydes were 93–115% with a relative standard deviation of 3.6–8.1% at the 0.1 μM level for aldehydes. The HPLC–DNPH method has been applied for determining aldehyde photoproducts from Cu(II)–amino acid complex systems.     

1,3,5,7-Tetramethyl-8-aminozide-difluoroboradiaza-s-indacene as a new fluorescent labeling reagent for the determination of aliphatic aldehydes in serum with high performance liquid chromatography

A BODIPY-based fluorescent derivatization reagent with a hydrazine moiety, 1,3,5,7-tetramethyl-8-aminozide-difluoroboradiaza-s-indacene (BODIPY-aminozide), has been designed for aldehyde labeling. An increased fluorescence quantum yield was observed from 0.38 to 0.94 in acetonitrile when it reacted with aldehydes. Twelve aliphatic aldehydes from formaldehyde to lauraldehyde were used to evaluate the analytical potential of this reagent by high performance liquid chromatography (HPLC) on C₁₈ column with fluorescence detection. The derivatization reaction of BODIPY-aminozide with aldehydes proceeded at 60 °C for 30 min to form stable corresponding BODIPY hydrazone derivatives in the presence of phosphoric acid as a catalyst. The maximum excitation (495 nm) and emission (505 nm) wavelengths were almost the same for all the aldehyde derivatives. A baseline separation of all the 12 aliphatic aldehydes (except formaldehyde and acetaldehyde) is achieved in 20 min with acetonitrile–tetrahydrofuran (THF)–water as mobile phase. The detection limits were obtained in the range from 0.43 to 0.69 nM (signal-to-noise = 3), which are better than or comparable with those obtained by the existing methods based on aldehyde labeling. This reagent has been applied to the precolumn derivatization followed with HPLC determination of trace aliphatic aldehydes in human serum samples without complex pretreatment or enrichment method.     

A Selective Synthesis of 3,3-Di-C-(hydroxymethyl)-3-deoxy-furanorono-1,4-lactone in the Formose Reaction

Abstract

The formose reaction, by which a complex mixture of sugars and sugar alcohols (the so-called formose) are produced by the base-catalyzed condensation of formaldehyde, has received much attention in connection with the prebiotic synthesis of carbohydrates² and the microbial utilization of formose.^3–5 Formose, however, has not been useful yet, because of the complexity of this product mixture (Fig. 1a). Therefore, it seemed desirable to make the reaction more selective.     

Analysis of primary aliphatic short-chain monoamines by LC in water samples

Several derivatization procedures with o-phthaldialdehyde-N-acetylcysteine (OPA-NAC) were compared for a rapid analysis of primary aliphatic short-chain monoamines in water samples by HPLC using a LiChorospher analytical separation column (100RP₁₈ mm i.d., 5 μm). Both the solution and the solid-support assisted off-line derivatization on C₁₈ SPE cartridges were inadequate options because of beginning degradation processes of the instable isoindol derivatives during their transfer to the analytical column. This problem was precluded with the on-column or solid-support assisted on-line derivatization. In the last mentioned procedure, the derivatization took place in a Hypersil C₁₈ precolumn ( mm i.d., 30 μm) connected with an additional preconcentration step resulting in better detection limits (0.002-0.040 μg ml⁻¹ requiring only 150 μl of water sample) than in the on-column procedure (0.08-0.16 μg ml⁻¹). The improved sample handling, the better control of parameters affecting reaction rates, the fully automation of this method with only 10 min analysis time for each sample are further advantageous. The potential of the solid-support assisted on-line derivatization was outlined and applied to water samples from several sources. Recovery values near 100% were obtained.     

First Synthesis of DL-2-C-Hydroxymethyl-3-Pentulose in the Formose Reaction

Abstract

The formose reactions² in N,N-dimethylformamide (DMF) catalyzed by 2-(dimethylamino)ethanol and thiamine hydrochloride, have been found to give rise to dihydroxyacetone and DL-glycero-tetrulose selectively at 1.1 M and 3.0 M of formaldehyde concentration, respectively. In our consecutive study on the formose reaction in DMF, it has been fortunately found that the distribution of products is able to be controlled by the amount of water added to the reaction mixture. We describe herein the first example of the favored formation of DL-2-C-hydroxymethyl-3-pentu-lose (GP-19¹) in the formose reaction using DMF-H₂O solvent, and it's isolation and structure elucidation.     

Comparison of several sorbents for continuous in situ derivatization and preconcentration of low-molecular mass aldehydes prior to liquid chromatography–tandem mass spectrometric determination in water samples

A comparative study of six SPE conventional and non-conventional sorbent materials (silica RP-C₁₈, LiChrolut EN, Amberlite XAD-2, C₆₀ fullerene, multiwall carbon nanotubes and graphitized carbon black) was carried out for the in situ derivatization/preconcentration of eight aldehydes with 2,4-dinitrophenylhydrazine. Although two of the sorbents, LiChrolut EN and RP-C₁₈, turned out to be the most suitable for ultratrace analysis of the aldehydes, LiChrolut EN showed higher capacity for 2,4-dinitrophenylhydrazine trapping (higher efficiency for the in situ derivatization reaction) and superior performance in terms of sensitivity (likely a result of its increased sample breakthrough volume). The LiChrolut EN-based method combined with LC–MS/MS allowed the determination of aldehydes over the linear range of 0.02–15 μg l⁻¹, with limits of detection at 6–24 ng l⁻¹ and precision of 3.2–7.2%. The method was applied to determine low-molecular mass aldehydes in water samples. These results indicate that the method proposed is a straightforward and sensitive tool for the determination of these aldehydes in water samples providing better results than those LC–MS/MS reported alternatives in terms of the limit of detection, sample requirements for analysis and cost.     

Flow injection spectrophotometric determination of formaldehyde based on its condensation with hydroxylamine and subsequent redox reaction with iron(III)-ferrozine complex

A flow injection (FI) spectrophotometric method is proposed for the determination of low concentration of formaldehyde (HCHO) in liquid media. It is based on the condensation of HCHO with hydroxylamine sulfate, followed by the reduction reaction of iron(III)-ferrozine complex with the residual hydroxylamine to form a purple iron(II)-ferrozine complex (λ_max = 562 nm). In the first reaction, hydroxylamine decreases proportionally to the concentration of HCHO, and therefore the produced purple iron(II)-ferrozine complex decreases with increasing HCHO (a negative FI peak is obtained). The detection limit (S/N = 3) was 1.6 μg L⁻¹. The method can be applied to the determination of HCHO in industrial wastewater.     

Analysis of methylamine by solid-phase microextraction and HPLC after on-fibre derivatization with 9-fluorenylmethyl chloroformate

A method for the determination of methylamine (MA) in aqueous matrices is reported which uses solid-phase microextraction (SPME) for enrichment and derivatization of the analyte, and high performance liquid chromatography (HPLC). The fluorogenic reagent 9-fluorenylmethyl chloroformate (FMOC) has been used for derivatization. The SPME fibres were successively immersed in the samples and in the derivatization solutions to extract MA and FMOC, respectively. After a defined time of reaction, the derivatized analyte was desorbed into the chromatographic system, and chromatographed in a LiChrosphere 100 RP18, i.d., 5 μm, column under gradient elution. In order to improve the MA-FMOC peak profile, a precolumn ( i.d., packed with Hypersil C₁₈ phase, 30 μm) was connected on-line to the analytical column by means of a switching valve. The experimental conditions (including fibre coating, times of adsorption, reaction and desorption, and concentration of reagent) have been optimised, and the results have been compared with those achieved by using a method previously validated for aliphatic amines in which extraction and derivatization were carried into C₁₈ solid-phase extraction (SPE) cartridges. Although less sensitive, the SPME based method allowed the quantification of MA over the range 2.5-10.0 μg/ml with linearity, reproducibility and accuracy comparable to that of the SPE based method, the limit of detection being 0.75 μg/ml. The main advantages of the proposed SPME procedure are: sample handling involved in the extraction and derivatization steps was considerably reduced, it was free organic solvent and non-destructive. Moreover, the proposed conditions allowed the selective determination of MA in the presence of other primary and secondary short-chain aliphatic amines. The utility of the proposed procedure for the quantification of MA in different types of waters is discussed.     

Formose Reactions. XXXII. Synthesis of Dl-2-C-Hydroxymethyl-3-Pentulose from Formaldehyde in N,N-Dimethylformamide-Water Mixed Solvent (II)

ABSTRACT

The carbon number of the main product and the total yield of products increased with an increase in the amount of triethylamine (TEA). Furthermore, the decrease of DL-2-C-hydroxymethyl-3-pentulose (2-H-3-P) was speeded up by increasing the TEA concentration and 2,4-bis(hydroxy-methyl)-3-pentulose (2,4-BH-3-P) increased smoothly along with the progress of the reaction. In the low formaldehyde (HCHO) concentration range (ca. 0.5 M), dihydroxyacetone (DHA) and DL-glycero-tetrulose were main products. 2-H-3-P and 2,4-BH-3-P increased with an increase in the formaldehyde concentration. Dihydroxyacetone, DL-glycero-tetrulose, 2-H-3-P and 2,4-BH-3-P were favorably obtained from a formose reaction by choosing a suitable [thiamine. HCl]/[HCHO] ratio. Under the reaction conditions reported in this paper, thiamine decomposed rapidly and lost its catalytic ability.     

Analysis of zearalenone and α-zearalenol in animal feed using high-performance liquid chromatography

Different extraction and clean-up techniques used before HPLC analysis were compared in order to obtain a reliable method for the quantitative determination of zearalenone (ZEA) and α-zearalenol (α-ZOL) in animal feed. Immunoaffinity clean-up was compared to C₁₈ and Florisil column clean-up. Extracted samples were analysed by reversed-phase HPLC with fluorescence detection (λ_ex=274 nm, λ_em=440 nm). A mobile phase of acetonitrile:water (50:50 (v/v)) and a flow-rate of 1.0 ml min⁻¹ resulted in a good separation between ZEA and α-ZOL. Using immunoaffinity clean-up the linear range was between 25 and 600 μg kg⁻¹ for ZEA and α-ZOL in maize. Intra-laboratory coefficients of variation (CV) (under repeatability conditions) were 9.16% for ZEA and 2.18% for α-ZOL. Recoveries for spiked ZEA and α-ZOL samples ranged from 89 to 110% with CVs between 5.2 and 11.2% (under within-laboratory reproducibility conditions). Using C₁₈ and Florisil solid-phase clean-up, matrix interference was too high. Therefore, naturally contaminated animal feed samples were analysed using the developed HPLC method coupled to the immunoaffinity clean-up.     

Analysis of fatty acids in lung tissues using gas chromatography-mass spectrometry preceded by derivatization-solid-phase microextraction with a novel fiber

In this article, a laboratory-made sol-gel derived fiber with butyl methacrylate/hydroxy-terminated silicone oil (BMA/OH-TSO) coating was first used for headspace solid-phase microextraction (HS-SPME) of medium and long chain fatty acids after derivatization and applied to the analysis of fatty acids in lung tissues by coupling to gas chromatography-mass spectrometry (GC-MS). The experimental parameters for derivatization, HS-SPME and desorption were optimized. Fatty acids in cancerous lung tissues from five patients with lung cancer were determined under the optimized conditions. Normal lung tissues from the same five patients were used as controls. This fiber showed higher extraction efficiency for fatty acids after derivatization when compared with commercial polydimethylsiloxane (PDMS) and polydimethylsiloxane-divinylbenzene (PDMS/DVB) fibers due to the three-dimensional network in the coating. The method presented in this paper showed satisfactory precision, accuracy, linearity and limits of detection (LODs). The relative standard deviation values were below 13.3% (n = 5) and the recoveries obtained ranged from 76.35% to 107.0%. The results obtained using the SPME method were also compared with those got by using liquid-liquid extraction (LLE) technique. It was found that the sensitivity could be enhanced by the SPME method. The analysis of the cancerous lung tissues and normal controls from five patients with lung cancer indicated that the main components of lung tissue were palmitic acid (C_16:0), stearic acid (C_18:0) and lignoceric acid (C_24:0). A comparison between the levels of the fatty acids in cancerous lung tissues and normal controls from the same a patient with lung cancer shows that most of the saturated fatty acids showed higher levels in cancerous lung tissues, while unsaturated fatty acids showed higher levels in normal controls on the whole.     

A divergent strategy for constructing a sugar library containing 2,6-dideoxy sugars and uncommon sugars with 4-substitution

A practical strategy has been developed for delivering 2,6-dideoxy sugars and uncommon sugars with 4-substitution. This strategy employed Ferrier rearrangement reaction and BF₃·OEt₂-induced peroxidation to construct key intermediates 2,3-unsaturated glycosides and α,β-unsaturated lactones from peracetyl rhamnal. After further derivatization, four uncommon sugars with 4-substitution and eight uncommon sugar units with 3,4-disubstitution were successfully synthesized.     

Determination of clarithromycin in rat plasma by HPLC-UV method with pre-column derivatization

A novel high-performance liquid chromatographic (HPLC) method using pre-column derivatization and UV detection at 275 nm for the determination of clarithromycin in rat plasma has been validated. Clarithromycin was extracted from plasma sample spiked with internal standard (erythromycin) under alkaline condition with ethyl ether and derivatizated with trimethylbromosilane. The analyses were run on a C₁₈ column, maintained at 40 °C during elution, using a mobile phase comprised of potassium dihydrogen phosphate (50 mM, pH 6.8, contained 0.7% triethylamine), acetonitrile, and methanol (30:45:25, v/v/v). The standard calibration curve for clarithromycin was linear (r² = 0.9998) over the concentration range of 0.1-10 μg ml⁻¹ in rat plasma. The limit of detection (LOD) and limit of quantitation (LOQ) was 30 ng ml⁻¹ and 0.1 μg ml⁻¹ respectively. The intra- and inter-day assay variability range was 2.6-7.4% and 3.3-8.5%, respectively. This method has been successfully applied to a pharmacokinetic study of clarithromycin in rats.     

In situ continuous derivatization/pre-concentration of carbonyl compounds with 2,4-dinitrophenylhydrazine in aqueous samples by solid-phase extraction: Application to liquid chromatography determination of aldehydes

A rapid and straightforward continuous solid-phase extraction system has been developed for in situ derivatization and pre-concentration of carbonyl compounds in aqueous samples. Initially 2,4-dinitrophenylhydrazine, the derivatizing agent, was adsorbed on a C₁₈ mini-column and then 15-ml of sample were continuously aspirated into the flow system, where the derivatization and pre-concentration of the analytes (low-molecular mass aldehydes) were performed simultaneously. Following elution, 20 μl of the extract were injected into a LC-DAD system, in which hydrazones were successfully separated in 12 min on a RP-C₁₈ column using a linear gradient mobile phase of acetonitrile-water of 60-100% acetonitrile for 8 min, flowing at 0.5 ml/min. The whole analytical process can be accomplished within ca. 35 min. Under optimum conditions, limits of detection were obtained between 0.3 and 1.0 μg/l and RSDs (inter-day precision) from 1.2 to 4.6%. Finally, some applications on water samples are presented with recoveries ranged from 95.8 to 99.4%.     

Residue determination of glyphosate in environmental water samples with high-performance liquid chromatography and UV detection after derivatization with 4-chloro-3,5-dinitrobenzotrifluoride

A pre-column derivatization high-performance liquid chromatographic method for glyphosate analysis has been developed. Derivatization of glyphosate was performed with 4-chloro-3,5-dinitrobenzotrifluoride (CNBF). In pH 9.5 H₃BO₃-Na₂B₄O₇ media, the reaction of glyphosate with CNBF completed at 60 °C for 30 min. The labeled glyphosate was separated on a Kromasil C18 column (250 mm × 4.6 mm, 5 μm) at room temperature and UV detection was applied at 360 nm. The separation of labeled glyphosate was achieved within 15 min by gradient elution mode. Compared to other pre-column derivatization, this derivatization was performed more mildly, the derivative was more stable, and the detection limits of a few reagents were higher than CNBF, except 9-fluorenylmethyl chloroformate (FMOC-Cl) using fluorescence and mass spectrometry, however, this reagent avoid to be removed after derivatization like FMOC-Cl. The detection limit of glyphosate was 0.009 mg L⁻¹ (S/N = 3) without preconcentration and reach MRL, which is set at the level of 0.1 mg L⁻¹ in China. The method linearity correlation coefficient was 0.9999, in concentrations ranging from 0.3 to 48.5 mg L⁻¹. The proposed method has been applied to the quantitative determination of glyphosate in environmental water with recoveries of 91.80-100.20% and R.S.D. of 2.27-6.80, depending on the sample investigated.     

HPLC Determination of α-Amino Acids in Phytoplanktonic Marine Cells

Abstract

A procedure for the quantitative determination of 17 amino acids in a marine matrix using HPLC is reported. Pre-column derivatization with o-phthalaldehyde, separation on C₁₈-bonded silica with phosphate buffer (pH 7.2)-acetonitrile as eluent and fluorescence detection have been used. The good variation coefficient (average 2% with working curves in real matrix) and the low detection limit (1-5 fmoles) make the procedure suitable for the determination of total or free amino acids in matrix cultures.     

Sol–gel coatings with covalently attached methyl,octyl, and octadecyl ligands for capillary microextraction. Effects of alkyl chain length and sol–gel precursor concentration on extraction behavior

Fused silica capillaries with surface-bonded sol–gel coatings containing covalently attached octadecyl, octyl, and methyl groups were prepared for capillary microextraction (CME) hyphenated on-line with high-performance liquid chromatography (HPLC). For this, octadecyltrimethoxysilane (C₁₈TMS), octyltrimethoxysilane (C₈TMS), or methyltrimethoxysilane (MTMS) was used as the respective sol–gel precursor. Hydrolytic polycondensation of these precursors led to the formation of surface-bonded sol–gel sorbents with pendant alkyl groups ready to serve as the extraction medium; no additional surface derivatization reactions were needed to anchor these ligands to the surface. Extraction behaviors of two sets of microextraction capillaries with alkyl-bonded sol–gel coatings were investigated: (a) capillaries prepared with a constant molar concentration of these precursors in the sol solution, and (b) capillaries prepared with varied molar concentrations of C₈TMS in the sol solution. Among the capillaries prepared using sol solutions with the same molar concentration of sol–gel precursor, the detection limits for nonpolar and polar analytes ranged from 0.3 ng/L to 213.9 ng/L. The sol–gel octadecyl-coated capillaries were found to be the most efficient at extracting these analytes, followed by the sol–gel octyl-coated capillaries, followed by the sol–gel methyl-coated capillaries. The results of this study point to the possibility that polar analytes are extracted through synergistic molecular level interactions of the polar and nonpolar parts of the analyte molecules with the alkyl chains and silanol groups within the sol–gel coatings. These coatings also demonstrated run-to-run and capillary-to-capillary reproducibility, with HPLC peak area RSD values ranging from 1.1% to 9.6% and 1.3% to 10.0%, respectively. In the set of sol–gel octyl capillaries with varied molar concentrations, the capillaries prepared with 0.514 M concentration of C₈TMS in the sol solution were most efficient in extracting nonpolar and polar analytes. When higher or lower concentrations of C₈TMS were used in the sol solution, the resulting sol–gel coated capillaries were less efficient in extracting nonpolar and polar analytes.     

Statistical evaluation of an analytical GC/MS method for the determination of long chain fatty acids

In-depth evaluation of an analytical method to detect and quantify long chain fatty acids (C₈-C₁₆) at trace level concentrations (25-1000 μg/l) is presented. The method requires derivatization of the acids with methanolic boron trifluoride, separation, and detection by gas chromatography-mass spectrometry. The calibration experiments passed all the tested performance criteria such as linearity, homoscedasticity, and ruggedness. The detection limits and related quantities were computed by applying the method detection limit, and the calibration line approximation. The values obtained by applying the latter approach were more reliable and consistent with the actual statistical theory of detection decisions and yielded the following concentrations: C₈, 87.6 μg/l; C₁₀, 45.2 μg/l; C₁₁, 39.9 μg/l; C₁₂, 37.7 μg/l; C₁₄, 41.4 μg/l and C₁₆, 40.6 μg/l. Two different gas-liquid chromatographic columns were tested and similar results achieved, which shows the ruggedness of the method.     

Comparison of Reverse-Phase High-Performance Liquid Chromatographic Methods for Precolumn-Derivatized Amino Acids

Abstract

A comparison was made among five precolumn derivatization techniques for amino acid analysis using reverse-phase high-performance liquid chromatography (HPLC). All chromatographic analyses were conducted using the same instrumentation and a C₁₈ Ultrasphere ODS column (5 μm, 250 × 4.6 mm). The precolumn derivatization methodologies studied included the formation of OPA (o-phthaldialdehyde), DANSYL (dimethylaminonaphthalenesulphonyl), DABSYL (dimethylaminoazobenzenesulphonyl), PTH (phenylthiohydantoin), and PTC (phenylthiocarbamyl) derivatives. The derivatization procedures were evaluated for simplicity, time required, and derivative stability. HPLC analyses of the amino acid derivatives were compared in terms of resolution, sensitivity, reproducibility, and time of analysis.