Adsorptive stripping voltammetric measurements of trace amounts of platinum(II) and ruthenium(III) in the presence of 1-(2-pyridylazo)-2-naphthol

An extremely sensitive stripping voltammetric procedure for low level measurements of platinum (II, IV) or ruthenium (III, IV) is reported. The method is based on the interfacial accumulation of the platinum (II) or ruthenium (III)-1-(2-pyridylazo)-2-naphthol complex on the surface of a hanging mercury drop electrode, followed by the reduction of the adsorbed complex during the cathodic scan. The peak potential was found to be –0.8 V vs. Ag/AgCl electrode and the reduction current of the adsorbed complex ions of platinum (II) or ruthenium (III) was measured by differential pulse cathodic stripping voltammetry. The optimum experimental conditions were: 1.5×10^–7 mol/l of 1-(2-pyridylazo)-2-naphthol solution of pH 9.3, preconcentration potential of –0.2 V, accumulation time of 3 min and pulse amplitude of 50 mV with 4 mV s^–1 scan rate in the presence of ethanol-water (30% v/v) — sodium sulphate (0.5 mol/l). Linear response up to 6.4 × 10^–8 and 5.1 × 10^–8 mol/l and a relative standard deviation (at 1.2×10^–8 mol/l) of 2.4 and 1.6% (n=5) for platinum (II) and ruthenium (III) respectively were obtained. The detection limits of platinum and ruthenium were 3.2×10^–10 and 4.1×10^–10 mol/l, respectively. The electronic spectra of the Pt(II) — PAN and Ru(III) — PAN complexes were measured at pH 9.3 and the stoichiometric ratios of the complexes formed were obtained by the molar ratio method. The effects of some interfering ions on the proposed procedure were critically investigated. The method was found suitable for the sub-microdetermination of ruthenium (IV) and platinum (IV) after their reduction to ruthenium (III) and platinum (II) with sulphur dioxide in acid media. The applicability of the method for the analysis of binary mixtures of ruthenium (III) and (IV) or platinum (II) and (IV) has also been carried out successfully. The method is simple, rapid, precise, and promising for the determination of the tested metal ions at micro-molar concentration level.     

Determination of Selenium(IV) by Stripping Voltammetry at a Mercury-Film Electrode

A procedure was proposed for the determination of selenium(IV) by stripping voltammetry on a mercury-film electrode at an electrolysis potential of +0.4 V versus the saturated silver–silver chloride reference electrode in a 1 M H₂SO₄ solution. The current of the cathodic peak is a linear function of the selenium(IV) concentration in the range from 5 × 10^–3 to 3 × 10^–1 mg/L (6.3 × 10^–8 to 3.8 × 10^–6 M) at a time of electrolysis of 30 s (t _el). The detection limit for selenium is 1 × 10^–4 mg/L (1.3 × 10^–9 M) at t _el = 300 s. It was shown that selenium(IV) can be determined in the presence of 10 mg/L Zn(II), 1 mg/L Cd(II), 0.5 mg/L Pb(II), and 0.2 mg/L Cu(II). A procedure for the determination of selenium in natural, mineral, and potable water was proposed.     

Spectrophotometric studies on the platinum(IV)-prochlorperazine bismethanesulfonate complex

We have studied the formation of a platinum complex and developed a simple, rapid and sensitive spectrophotometric method for the determination of platinum in solution. The method is based on the complexation reaction of the chromogen, prochlorperazine bismethane-sulfonate (PCPMS), with platinum(IV) in phosphoric acid medium which forms a reddish brown 1 1 complex with an absorption maximum around 528 nm. The reaction is fast in the presence of copper(II) and goes to completion within 1 min. Beer's law is obeyed over the concentration range 0.3–7.2 g/ml of platinum(IV) with an optimal range of 1.2–6.6 g/ml. The molar absorptivity is 2.65 × 10⁴1 mol^–1 cm^–1 and the Sandell's sensitivity is 7.8 ng cm^–2. The stability constant, logK, of the complex is 4.96±0.1 at 25 ° C. The effects of time, temperature, concentrations of acids, PCPMS and copper(II), and the interference by various ions are investigated. The method has been successfully applied to the determination of platinum content in alloys and minerals.     

Quenching of luminescence of terbium(III) by platinum(IV) complexes

The rate constants (k_q) of the bimolecular energy-transfer reactions in systems consisting of the terbium(III) aquo complex and platinum(IV) complexes have been determined. The influence of the electronic and nuclear factors on the values of the rate constant of the reactions has been considered. It has been shown that the platinum(IV) complexes make up an adiabatic family of quenchers, while the energy-transfer reactions between terbium(III) aquo complexes are characterized by a high degree of nonadiabaticity x -10^–12). Estimates of the energies of the pure electronic transitions to electronically excited states of platinum(IV) complexes which are not observed spectroscopically have been obtained on the basis of the dependence of k_q on the change in the free energy of the energy-transfer process.Translated from Teoreticheskaya i Éksperimental'naya Khimiya, Vol. 25, No. 5, pp. 618–623, September–October, 1989.     

Electroanalytical chemistry of metal complexes with S-containing ligands

Summary The main types of electrochemical reactions of complexes in organic and mixed solvents are considered. Fast electrochemical reactions (k _s=n×10^–2 cm · s^–1) were used to reduce the minimal concentrations (c _min) in a.c. voltammetry. The role of pre- and post-chemical reactions in the formation of the analytical signal in extraction voltammetry is elucidated. The principles of the influence of the special structure of the complexes on their redox properties are determined using complexes of the transition metals with phosphorus dithioacids and bidentate heterocyclic amines. The features of the electrooxidation and electroreduction of inert complexes of the platinum metals with heterocyclic dithioacids and organic sulphides in nonaqueous media are discussed. The products of the electrochemical reaction of these compounds in protic media catalyze the hydrogen evolution on the mercury electrode. Kinetic data of the chelate formation are used for developing highly selective methods for the determination of the platinum metals with c _min=2×10^–9–5×10^–8 mol/l.

---

Elektrochemische Reaktionen von Komplexen mit S-haltigen Liganden

     

Determination of titanium by adsorption-voltammetry with 2-(5-bromo-2-pyridylazo)-5-(diethylamino)-phenol (5-Br-PADAP)

Summary The 1:1 complex between titanium (IV) and 5-Br-PADAP can be used to determine titanium by adsorption voltammetry at a stationary Hg-electrode. The experimental conditions for the determination are described. The detection limit is 3×10^–10 mol/l Ti (0.015 ppb). Calibration curves are linear for solutions containing 4×10^–10 to 5×10^–8 mol/l Ti(IV) and an enrichment time of 3 min. The influence of foreign ions was investigated. The determination can be carried out in the presence of a 5000-fold excess of iron.     

Sensitive flotation-spectrophotometric method for the determination of vanadium (IV) with 3,5-dinitrosalicylic acid and rhodamine B

Vanadium(IV) is determined by reaction with 3,5-dinitrosalicylic acid and rhodamine B in weakly acidic medium. The flotation of the ternary ion-association complex is carried out with cyclohexane followed by dissolution in acetone for subsequent spectrophotometric determination. The molar absorptivity is 5.91×10⁵ l mole^–1 cm^–1 at 555 nm. Beer's law is obeyed in the range 0.05–1.5 g vanadium(IV) in 25 ml. The method is selective for vanadium(IV) in the presence of sodium fluoride and has been applied to standard reference materials.     

Simultaneous Spectrophotometric Determination of Rare-Earth and Transition Elements Using Partial Least-Squares (PLS) Multivariate Calibration

A spectrophotometric method for the simultaneous determination of rare-earth and transition elements in synthetic superconductors, [(La_{1 – x} Eu _x )_1.82Sr_0.18CuO₄], by the use of 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol (5-Br-PADAP) as chelating agent was developed. The influence of chemical variables affecting the reaction was studied. A partial least-squares (PLS) multivariate calibration procedure was used to assess the data obtained from several calibration solutions measured over the wavelengths range 400–700 nm. The concentration range for Cu was (1–12) × 10^–6 mol/L, while the range for the rare-earth elements La and Eu was (2–8) × 10^–6 mol/L. The relative errors in the determinations were less than 5% in most cases.     

Spectrophotometric determination of cationic and anionic surfactants with anionic dyes in the presence of nonionic surfactants,part II: Development of batch and flow injection methods

On the basis of the changes in absorption spectra of azo dyes on the addition of an organic onium ion, spectrophotometric methods for the determination of organic onium salts and anionic surfactants were developed, and applied to flow injection method. Propyl orange (PO^–) was used for the determination of organic onium ions. Pairs of PO^– and Zeph⁺ (tetradecyldimethyl-benzylammonium ion) or PO^– and nC₁₈TMA⁺ (n-octadecyltrimethylammonium ion) were used for the determination of anionic surfactants. The determination range of organic onium ions were (0–3) × 10^–5 M by a batch method and were (0–2) × 10^–5 M by a flow injection method. The determination ranges of anionic surfactants were (0–2) × 10^–5 M by the batch method, and were (0–5) × 10^–5 M by the flow injection method, and the detection limit corresponding toS/N = 3 was 3 × 10^–7 M by the flow injection method. By the proposed flow injection method, anionic surfactants in water samples were determined.     

Spectrophotometric determination of vanadium(IV) in the presence of vanadium(V) using Br-PADAP

In the present paper, a simple and sensitive method is proposed for vanadium(IV) determination in the presence of vanadium(V). This is based on the oxidation of vanadium(IV) present in the sample to vanadium(V) by addition of iron(III) cation, followed by a complexation reaction of iron(II) with the spectrophotometric reagent 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol (Br-PADAP). The iron(II) reacts with Br-PADAP immediately, forming a stable complex with a large molar absorptivity. The vanadium(IV) determination is possible, with a calibration sensitivity of 0.549 g ml^–1, for an analytical curve of 18.8 ng ml^–1 to 2.40 g ml^–1, molar absorptivity of 2.80 × 10⁴ 1 mole^–1 cm^–1 and a detection limit of 5.5 ng ml^–1. Selectivity was increased with the use of EDTA as a masking agent. The proposed method was applied for the vanadium(IV) determination in the presence of several amounts of vanadium(V). The results revealed that 200 g of vanadium(V) do not interfere with determination of 5.00 g of vanadium(IV). The precision and the accuracy obtained were satisfactory (R. S. D.<2%).     

Spectrophotometric determination of gold by reaction with molybdate and nile blue in the presence of PVA

A spectrophotometric method for the determination of gold has been developed, based on the reaction of gold(III) with molybdate and nile blue (NB) to form an ion-association complex in the presence of poly(vinyl alcohol). The molar absorptivity at 595 nm is 2.71 × 10⁵ l mol^–1 cm^–1. Beer's law is obeyed over the range 0–16 g of gold per 25 ml. The relative standard deviation evaluated from seven independent determinations of 0.4 g/ml of gold is 2.6%. The limit of detection is 0.011 g/ml. The molar ratio of Au to NB in the complex is established to be 1 2. Over 30 foreign ions were tested for interference; Pt(IV), Sb(III), W(VI) and SiO ₃ ^2– interfered and had to be separated from gold on polyurethane foam. The method can be applied to the spectrophotometric determination of trace amounts of gold in powdered carbon and some ores.     

Simultaneous determination of uranium(IV) and iron(II) with a stopped-flow inductive kinetic spectrophotometric method

A kinetic method for simultaneous determination of multielements is proposed, and a procedure for simultaneous determination of uranium(VI) and iron(II) is established based on their inductive effect on the chromium(VI)-iodide redox reaction in weak acidic medium. The reaction was monitored with the stopped-flow spectrophotometric technique by using I ₃ ^– -starch complex as indicator. The calibration graphs are linear for 0–3.6 g.cm^–3 U(IV), and 0–2.5 g.cm^–3 Fe(II), respectively. Most foreign ions, except for V(IV), Sb(III), do not interfere with the determination.     

Individual and sequential flow injection spectrophotometric determination of vanadium(V) and titanium(IV)

Summary Methods for the individual and sequential flow injection spectrophotometric determination of vanadium(V) and titanium(IV) are proposed, based on the formation of peroxo complexes. The detection limits are 1.0 × 10^–5 mol/l V (120 l) and 2.5 × 10^–6 mol/l Ti (80 l). A cation exchange resin mini-column is incorporated on-line into the vanadium manifold to remove the titanium complex and allow the vanadium to be determined selectively. A normal injection valve is used for the individual determinations, but it is modified for determination of V(V)/–Ti(IV) mixtures in order to introduce two samples sequentially into the reagent stream. One passes through a cation exchanger minicolumn, the other through an empty column, before reaching the detector. The former allows V alone to be measured, the latter V+Ti.

---

Individuelle und sequentielle spektralphotometrische Fließinjektionsbestimmung von Vanadium(V) und Titan(IV)

---

Dedicated to Prof. Dr. G. Tölg on the occasion of his 60th birthday     

Synthesis and applications of poly(acryl<Emphasis Type="Italic">p</Emphasis>-aminobenzenesulfonamideamidine-<Emphasis Type="Italic">p</Emphasis>-aminobenzenesulfonylamide) chelating fiber for pre-concentrating and separating trace Bi(III), Hg(III), Au(III) and Pd(IV) from solution samples

Poly(acrylp-aminobenzenesulfonamideamidine-p-aminobenzenesulfonylamide) chelating fiber containing "S", "N", and "O" elements was synthesized from polyacrylonitrile fiber and p-aminobenzene sulfonamide and used to enrich and separate trace Bi(III), Hg(III), Au(III), and Pd(IV) ions from wastewater and ore sample solution. The enrichment acidity, flow rate, elution conditions, reuse, interference ions, saturated adsorption capacity, constant of adsorption rate, analytical accuracy, and actual samples on chelating fiber were investigated by means of inductively coupled plasma optical emission spectrometry (ICP-OES) with satisfactory results. Solutions of 100 ng mL^–1 of Bi(III), Hg(III), Au(III), and Pd(IV) ions can be enriched quantitatively by this chelating fiber at a rate of 1.0 mL min^–1 at pH 4 and desorbed quantitatively with 20 mL of 0.25 M HCl and 2% CS(NH₂)₂ solution at 50 °C (with recovery 97%). When the chelating fiber was reused for 20 times, the recoveries of the analyzed ions enriched by the fiber were still over 95% (except for Hg(III)). One thousand-fold excesses of Mn²⁺, Ca²⁺, Zn²⁺, Mg²⁺, Fe³⁺, Cu²⁺, Ni²⁺, Al³⁺, and Ba²⁺ ions and thousands-fold excesses of Na⁺ and K⁺ cause little interference in the pre-concentration and determination of the analyzed ions. The saturated adsorption capacity of Bi(III), Hg(III), Au(III), and Pd(IV) was 4.850×10^–4, 3.235×10^–4, 2.807×10^–4, and 3.386×10^–4 mol g^–1, respectively. The constants of adsorption rate were 0.409 min^–1 for Bi, 0.122 min^–1 for Hg, 0.039 min^–1 for Au, and 0.080 min^–1 for Pd. The relative standard deviations (RSDs) for the enrichment and determination of 10 ng mL^–1 Bi(III), Hg(III), Au(III), and Pd(IV) were lower than 2.3%. The results obtained for these ions in actual samples by this method were basically in agreement with the given values with average errors of less than 1.0%. FT-IR spectra shows that the existence of –SO₂–Ar, –H₂N–Ar, O=C–NH–, HN=C–NH–, and –HN–SO₂ functional groups are verified in the chelating fiber. From the FT-IR spectroscopy, we can see that Hg(III), Au(III), and Pd(IV) are mainly combined with nitrogen and sulfur (or oxygen), and Bi(III) is mainly combined with nitrogen (or oxygen) of the groups to form a chelating complex.     

A new procedure for the spectrophotometric determination of nitrogen(II) oxide in solutions

A new simple and reliable procedure was developed for the spectrophotometric determination of nitrogen(II) oxide. The procedure is based on the determination of excess oxygen after its reaction with NO. Alkaline solutions of thiourea dioxide were used for the determination of oxygen. It was found that the decomposition of an alkaline solution of thiourea dioxide under aerobic conditions is accompanied by the formation of dithionite, and its concentration is proportional to the concentration of oxygen in the solution. The absorbance of the resulting dithionite was measured at 315 nm. The solutions obeyed Beers law at oxygen concentrations of 1 × 10^–5–1.5 × 10^–3 M. The analytical range for NO was 1 × 10^–5–1.5 × 10^–3 M. The proposed procedure was also used for the determination of nitrogen(II) oxide in aqueous-ethanolic solutions.Translated from Zhurnal Analiticheskoi Khimii, Vol. 60, No. 1, 2005, pp. 27–29.Original Russian Text Copyright © 2005 by Pukhovskaya, Guseva, Makarov, Naidenko.     

Kinetics and mechanism of ligand substitution of mono(polyamine)-nickel(II) complexes with 4-(2-pyridylazo)resorcinol

Summary The kinetics and mechanism of ligand substitution reactions of tetraethylenepentamine nickel(II), Ni (Teren), and triethylenetetraamine nickel(II), Ni(Trien), with 4-(2-pyridylazo)resorcinol (parH₂) have been studied spectrophotometrically at I=0.1 M (NaClO₄) at 25°C. In both systems two distinct reaction steps are observed. The rapid first step follows the rate law d[Ni(Polyamine)(ParH₂)]/dt=k₁ [Ni(Polyamine)] [ParH₂]. The formation of ternary complexes of Ni (Polyamine) with ParH₂ has been investigated under second order equal concentration conditions. The values of second order rate constants for the Trien and Teren reactions are (2.1±0.2)×10⁴ M^–1s^–1 and (7.8±0.6)×10³ M^–1s^–1 respectively at pH=9.0, I=0.1 M and 25°C.The rate law for the second step may be written as d[Ni(Par)₂]/dt=k₂[Ni(Polyamine)(ParH₂)]. Values of k₂ for the Trien and Teren systems are (2.5±0.1)×10^–4 s^–1 and (4.76±0.3)×10^–5 s^–1 respectively.     

Comparative study on the determination of cephalexin in its dosage forms by spectrophotometry and HPLC with UV-vis detection

This paper discusses the spectrophotometric determination of cephalexin as the intact cephalexin or as its acid-induced degradation product. Cephalexin can be determined in the range 1 × 10^–5–18 × 10^–5 M with relative standard deviations of 5-1%. The limits of quantitation and detection were 10^–5 and 0.3 × 10^–5 M, respectively. These procedures were compared with reversed-phase HPLC determination. No interference was observed in the presence of common pharmaceutical adjuvants. The H-point standard additions method was applied in order to correct for the possible presence of the cephalexin precursor, 7-aminocephalosporanic acid; this improves the selectivity of the UV-vis spectrophotometric method.     

Kinetics of oxidation of hypophosphite ion by platinum(IV) in an alkaline medium

Summary The kinetics of the oxidation of hypophosphite ion by platinum(IV) have been studied spectrophotometrically in alkaline medium at different temperatures. The rate increases as the pH increases and the empirical rate law applicable to the reaction is given by:-d[Pt^IV]/dt = k₃[Pt^IV][H₂PO^2–][OH^–]The rate constant is 2.17×10^–3 (l² mo^–2s^–1) at 40.5°. The energy and entropy of activation for the reaction are 104.2 kJ mol^–1 and 28.5 JK^–1mol^–1 respectively.     

Spectrophotometric and derivative spectrophotometric study of the reaction of palladium (II) and rhodium (III) with 5-(3,4-methoxyhydroxybenzylidene)rhodanine and cationic surfactants

Spectrophotometric and derivative spectrophotometric methods for the determination of Pd(II) and Rh(III) are proposed. Pd(II) forms with 5-(3,4-methoxyhydroxybenzylidene)rhodanine [3,4-MHBR], in the absence and presence of cetylpyridinium bromide [CPB], 14 binary and 134 ternary complexes having molar absorptivities of 5.77 × 10⁴ and 7.46 × 10⁴ M ^–1cm^–1 at 525 and 530 nm, respectively. Rh(III) forms a 14 complex with 3,4-MHBR in the presence of cetyltrimethylammonium bromide [CTAB], which gives a maximum absorbance at 445 nm with a molar absorptivity of 5.13 × 10⁴ M ^–1cm^–1. Derivative spectrophotometric methods are employed for the determination of Pd(II) and Rh(III) at ng ml^–1 levels utilizing these complexes. Under the optimum conditions the calibration lines for Pd(II) and Rh(III) determination fit the equations d⁴ A/d⁴ = 1.10 × 10⁶ [Pd] – 0.018 (r = 0.9967) and d⁴ A/d⁴ = 2.25 × 10⁶ [Rh] + 0.03 (r = 1.0426) and have detection limits of 5.6 and 1.2 ng ml^–1, respectively. The influences of experimental variables and foreign ions are studied. The methods are free of interference from most common metal ions and anions. The results of the analysis of some synthetic mixtures of Pd(II) and Rh(III) are reported.     

4(5)-D-Arabinotetrahydroxybutylimidazoline-2-thione (THBIT), a new reagent for the spectrophotometric determination of palladium

Summary 4(5)-D-Arabinotetrahydroxybutylimidazoline-2-thione, THBIT, is proposed as a new reagent for the spectrophotometric determination of Pd(II). Pd(II) forms 11, 12 and 14 complexes with THBIT. The system conforms to Beer's law up to 5g/ml palladium concentration in aqueous medium (molar absorptivity, 1.99×10⁴ l· mole^–1·cm^–1 at 338 nm). The most serious interference is from Hg(II), Os(VIII), Ru(IV), Cr(VI), V(V) and S₂O₃ ^2–. The method has been used successfully for the determination of palladium in catalysts and synthetic samples.