Modification of B-site doping of perovskite LaxSr1 − xFe1 − y−zCoyCrzO3 − δ oxide by Mg2+ ion

Co-doping B-site of perovskite oxide La_xSr_1 ? xCo_yFe_1 ? yO_3 ? δ (LSCFO) with Cr⁶⁺ and Mg²⁺ ions has been attempted in this research for revamping chemical stability and oxygen ionic conductivity of this mixed conducting oxide. It is known that partial substitution for B-site cations of LSCFO by Cr gives rise to a significant improvement on chemical and thermal stability of the perovskite oxide. On the basis of this doped structure, introduction of an immaterial dose of Mg²⁺ ion into its B-site results in a microstructure consisting of smaller grains with higher density than its precursor. Furthermore, the resulting perovskite oxide La_0.19Sr_0.8Fe_0.69Co_0.1Cr_0.2 Mg_0.01O_3 ? δ (LSFCCMO) displays higher O^2? conductivity than the solely Cr-doped LSCFO besides the improved chemical stability against reduction in 5% CH₄/He stream at 850 °C. A detailed examination of the oxidation states of B-site transition metal ions by XPS has also been conducted as a part of structural characterizations of LSFCCMO. The assessment of relative O^2? conductivity shows that the grain boundary area plays a more important role than the bulk phase in facilitating ion transport, but with comparable boundary areas the higher densification level is favorable.     

2.7 μm fluorescence radiative dynamics and energy transfer between Er3+ and Tm3+ ions in fluoride glass under 800 nm and 980 nm excitation

A detailed study of the fluorescence radiative dynamics and energy transfer processes between Er and Tm ions in the Er³⁺/Tm³⁺ doped fluoride glass is reported. The fluorescence properties of 2.7 μm emission, other infrared and visible emissions are investigated under different selective laser excitations. Three Judd–Ofelt intensity parameters, energy transfer microparameters and efficiency have been determined and discussed. It is found that present Er³⁺/Tm³⁺ doped fluoride glass possesses large calculated emission cross section (8.98×10^–21 cm²) around 2.7 μm. The more suitable pumping scheme for laser applications at 2.7 μm laser is 980 nm excitation for Er³⁺/Tm³⁺ doped fluoride glass.     

Haven Correlation Parameter for Diffusion of Fluorine in Superionic Conductors La1 – ySryF3 – y

Physics of the Solid State - The processes of electric charge transfer (conductivity) and mass transfer (diffusion) in La1 ‒ ySryF3 – y superionic...     

Blue upconversion luminescence in 12 CaO·7 Al2O3:Tm3 +/Yb3 + polycrystals

The effect of Yb^3 + concentration on the fluorescence of 12 CaO·7 Al₂O₃:Tm^3 +/Yb^3 + polycrystals is investigated. Under the excitation of 980 nm laser, the strong blue (477 nm) emission band is observed and attributed to ¹G₄ → ³H₆ of Tm^3 +. The ratio of blue to red emission increases with the increasing of Yb^3 + and remains constant at 10 mol% Yb^3 +. The pump dependence and upconversion mechanisms show that the two-photon cooperative upconversion process is responsible for the enhancement of the blue upconversion emission. The Commission Internationale de l'eclairage chromaticity coordinates (x, y) illustrate that the 12 CaO·7 Al₂O₃:1 mol% Tm^3 +/10 mol% Yb^3 + can emit high-purity blue light.     

Synthesis and electrical properties of nanocrystalline Ca1 − xEuxMnO3 ± δ (0.1 ≤ x ≤ 0.4) powders prepared at low temperature using citrate gel method

Nanopowders of Ca_1 − xEu_xMnO₃ (0.1 ≤ x ≤ 0.4) manganites were synthesized as a single phase using the auto gel-combustion method. The citrate method shows to be simple and appropriate to obtain single phases avoiding segregation or contamination. The Ca_1 − xEu_xMnO₃ system has been synthesized at 800 °C during 18 h, against the conventional method of mixing oxides used to obtain these materials at higher temperatures of synthesis. The formation reaction was monitored by X-ray diffraction (XRD) analysis and an infrared absorption technique (FTIR). The polycrystalline powders are characterised by nanometric particle size, ∼ 48 nm as determined from X-ray line broadening analysis using the Scherrer equation. Morphological analysis of the powders, using the scanning electron microscope (SEM), revealed that all phases are homogeneous and the europium-substituted samples exhibit a significant decrease in the grain size when compared with the undoped samples. The structure refinement by using the Rietveld method indicates that the partial calcium substitution by europium (for x ≥ 0.3) modifies the orthorhombic structure of the CaMnO₃ perovskite towards a monoclinic phase. All manganites show two active IR vibrational modes around 400 and 600 cm^− 1. The high temperature dependence of electrical resistivity (between 25 and 600 °C) allows us to conclude that all the samples exhibit a semiconductor behaviour and the europium causes a decrease in the electrical resistivity by more than one order of magnitude. The results can be well attributed to the Mn⁴⁺/Mn³⁺ ratio.     

H/D Isotope Effect in the Conductivity of CaZr1 – xScxO3 – α in Reducing Atmospheres

Physics of the Solid State - The ionic (proton and deuteron) conductivity of the system CaZr1 – xScxO3 – α (x = 0.03–0.20) is studied...     

Effect of Eu dopant concentration in SrCe1 − xEuxO3 − δ on ambipolar conductivity

The europium dopant concentration in strontium cerate was studied to achieve maximum hydrogen permeation. In order to determine high ambipolar conductivity, total conductivity and open circuit potential measurements were performed. Among the three different compositions of Eu-doped SrCe_1 ? xEu_xO_3 ? δ (x = 0.1, 0.15 and 0.2) studied, SrCe_0.9Eu_0.1O_3 ? δ showed highest total conductivity between 600 °C and 900 °C. However, transference number measurements showed increasing electronic conductivity with increasing dopant concentration and a stronger temperature dependence for electronic conduction. Therefore, the highest ambipolar conductivity was obtained over the compositional range from SrCe_0.85Eu_0.15O_3 ? δ to SrCe_0.8Eu_0.2O_3 ? δ depending on temperature. Finally, the hydrogen permeation flux was calculated based on the ambipolar conductivity and compared with experimental results.     

On the superconductivity and structural properties of YBa2Cu3 − xCdxO7 − y

A series of superconducting cuprates with the nominal composition YBa₂Cu_3 − xCd_xO_7 − yand the effect of Cd substitution on Cu sites in this compound is presented. X-ray powder diffraction patterns for these cadmium cuprates with reduced diamagnetism indicate an orthorhombic unit cell like-perovskite structure for (0 ≤ x ≤ 0.15), while for higher Cd concentration, i.e.x = 1.0 the material is polyphasic. The observed superconducting transition temperature of the samples is nearly the same ([formula] K), except for (x = 1.0) whereT_cdrops to 72 K and a transition from metallic to semiconducting behavior of the normal state of the resistivity is observed. Such a decrease inT_cfor higher Cd concentration could be attributed to the presence of the green phase in this composition.     

Tuneability of Sm(1 − x)CexFeO3 ± λ perovskites: Thermal stability and electrical conductivity

Trimetallic perovskite oxides, Sm_(1 ? x)Ce_xFeO_3 ± λ (x = 0–0.05), were prepared by thermal decomposition of amorphous citrate precursors followed by calcinations. The material properties of the substituted perovskites were characterized by X-ray diffraction (XRD), X-ray florescence spectroscopy (XRF), scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS). The doped materials exhibited a single perovskite phase in air up to 1350 °C and have specific surface areas in the range of 2.696–8.665 m²/g. In reducing atmosphere (5%v/vH₂/N₂), the unsubstituted perovskite (x = 0) decomposed into two phases while the ceria stabilized materials (x = 0.01, x = 0.03, x = 0.05) remained in a single phase as revealed by XRD analysis. Their conductivities were measured by the four point probe method in air and in dilute hydrogen (5%v/vH₂/N₂) separately. The ceria substituted materials show increased stability versus reduction and phase separation for a wide temperature range (up to 1000 °C). Although undoped SmFeO₃ has higher conductivity under oxidizing conditions than ceria doped SmFeO₃ due its p-type nature, the situation is reversed under reducing conditions. The ceria substituted perovskites (Sm_(1 ? x)Ce_xFeO_3 ± λ, x = 0–0.05) showed higher conductivity in reducing than in oxidizing conditions, suggesting that ceria doping at the A-site has changed the SmFeO₃ from p-type to n-type semi-conducting behavior.     

Diode-pumped monolithic Er3+:Yb3+:YAl3(BO3)4 micro-laser at 1.6 μm

Efficient eye-safe 1.6 μm monolithic laser was realized in a c-cut, 0.7-mm-thick Er³⁺:Yb³⁺:YAl₃(BO₃)₄ microchip end-pumped by a quasi-continuous-wave 970 nm diode laser. At incident pump peak power of 20.4 W, a maximum output peak power of 2.6 W with a slope efficiency of 19% was obtained when the waist radius of pump laser beam was 220 μm. The spectra and profiles of output beam of the Er³⁺:Yb³⁺:YAl₃(BO₃)₄ monolithic laser were measured. The influences of the waist radius of pump laser beam on the slope efficiency and threshold of the monolithic laser were also investigated.     

SrTiO3(100) − √5 × √5 − R26.6 surface observed by high-resolution scanning tunneling microscopy

SrTiO₃(100) – (√5 × √5) – R26.6 surfaces were studied by means of high-resolution scanning tunneling microscopy (STM) under ultrahigh vacuum conditions. By varying the bias voltage in the occupied state, it was possible to observe the arrangement of titanium and oxygen atoms in the unit cells of a (√5 × √5) surface superstructure, which revealed that the TiO₂ layer is the terminating plane of the (√5 × √5) surface. In the STM images, peculiar protrusions were seen at the oxygen fourfold hollow site responsible for √5 × √5 periodicity. The protrusions are asymmetrical in contrast, which would be an important consideration in proposing accurate structural models for (√5 × √5) surface superstructures.     

Enhanced 2.0 μm emission in Ho3+/Yb3+ co-doped silica-germanate glass

A detailed investigation on thermal and spectroscopic properties of different Ho³⁺/Yb³⁺ concentration ratios in silica-germanate glasses is displayed. According to the measurement of thermal properties, the host glass possesses high transition temperature (585 °C) as well as the large ΔT(155 °C). The 2.0 μm fluorescence can be obtained from all the samples. Maximum stimulated emission cross-section of around 2.0 μm is 0.56 × 10⁻²⁰ cm² of Ho³⁺ as calculated by McCumber theory. Besides, the underlying mechanism is analyzed by means of fluorescence spectra. Thus, desirable thermal properties and spectroscopic characteristics of Ho³⁺/Yb³⁺ co-doped silica-germanate glass is a promising material in 2.0 μm emission.     

Performance evaluation of 64 × 10 Gbps and 96 × 10 Gbps DWDM system with hybrid optical amplifier for different modulation formats

In this paper, we investigated the performance of multi terabits DWDM system consisting of hybrid optical amplifier RAMAN-EDFA for different data format such as non-return to zero (NRZ), return to zero (RZ) and differential phase shift keying (DPSK). We find that in 64 × 10 and 96 × 10 Gbps, RZ is more adversely affected by nonlinearities, where as NRZ and DPSK is more affected by dispersion. We further show that RZ provide good quality factor (13.88 dB and 15.93 dB for 64 and 96 channels), less eye closure (2.609 dB and 3.191 dB for 64 and 96 channels) and acceptable bit error rate (3.89 × 10⁸ and 1.24 × 10⁹ for 64 and 96 channels) at the respective distance as compare to other existing modulation format. We further investigated the maximum single span distance covered by using existing data formats.     

Electronic structure of CuClxBr1 − x,CuClxI1 − xand CuBrxI1 − xalloys

In this work, the electronic structure and disorder effects in copper halides alloys are studied by means of the full potential linearized augmented plane wave (FLAPW) method. The calculated bowing parameter shows that the main contribution is due to the relaxation effects, though the charge transfer remains relatively significant, while the volume deformation contribution is negligible. The total bowing is found to be small in the three studied alloys. Results agree well with experimental and available theoretical works.     

Investigation on Tm3+-doped silicate glass for 1.8 μm emission

A Tm³⁺-doped silicate glass (SiO₂–CaO–Na₂O–K₂O) with good thermal stability is prepared by the melt-quenching method. Intense 1.8 μm emission is obtained when pumped by an 808 nm laser diode. Based on the measured absorption spectra, radiative properties are predicted using Judd–Ofelt theory and Judd–Ofelt parameters Ω_λ (λ=2, 4, 6), as well as absorption and emission cross-sections are calculated and analyzed. The difference between the measured Tm³⁺:³F₄ lifetime and the calculated lifetime is also discussed. The emission property together with good thermal property indicates that Tm³⁺-doped silicate glass is a potential kind of laser glass for efficient 2 μm laser.     

2μm emission performance in Ho3+ doped fluorophosphate glasses sensitized with Er3+ and Tm3+ under 800 nm excitation

The spectroscopic properties and energy transfer mechanisms in Ho³⁺ doped fluorophosphate glasses sensitized by Er³⁺ and Tm³⁺ at the 2 μm region are investigated. The absorption spectra and fluorescence spectra of the Tm–Ho doubly-doped glass system and Er–Tm–Ho triply-doped glass system are measured. According to the absorption spectra, the Judd–Ofelt parameters and spontaneous transition probability are calculated and compared with those of other glass hosts. From the fluorescence spectra, the fluorescence intensity of Er–Tm–Ho glass system at 2.0 μm is 0.95 and larger than that of the Tm–Ho glass system, which is 0.69. Meanwhile, the 2.0 μm to 1.8 μm and 2.0 μm to 1.53 μm peak intensity ratios in the Er–Tm–Ho glass system are 8.63 and 22.79, respectively, suggesting sufficient energy transfer between Er³⁺, Tm³⁺ and Ho³⁺ ions. In addition, the pumping schemes and energy transfer mechanisms of Tm–Ho doubly-doped and Er–Tm–Ho triply-doped glasses are discussed. The study indicates that the Er–Tm–Ho triply-doped glass system is a significant sensitized way pumped at 800 nm in fluorophosphate glasses for 2 μm applications.     

Ab initio study of Yb on the Ge(111)–(3 × 2) and Si(111)–(3 × 2) surfaces

The surface reconstruction, 3 × 2, induced by Yb adsorption on a Ge (Si)(111) surface has been studied using first principles density-functional calculation within the generalized gradient approximation. The two different possible adsorption sites have been considered: (i) H₃ (this site is directly above a fourth-layer Ge (Si) atom) and (ii) T₄ (directly above a second-layer Ge (Si) atom). We have found that the total energies corresponding to these binding sites are nearly the same, indeed for the Yb/Ge (Si)(111)–(3 × 2) structure the T₄ model is slightly energetic by about 0.01 (0.08) eV/unitcell compared with the H₃ model. In particular for the Ge sublayer, the energy difference is small, and therefore it is possible that the T₄, H₃, or T₄H₃ (half of the adatoms occupy the T₄ adsorption site and the rest of the adatoms are located at the H₃ site) binding sites can coexist with REM/Ge(111)–(3 × 2). In contrast to the proposed model, we have not determined any buckling in the Ge = Ge double bond. The electronic band structures of the surfaces and the corresponding natures of their orbitals have also been calculated. Our results for both substrates are seen to be in agreement with the recent experimental data, especially that of the Yb/Si(111)–(3 × 2) surface.