丙烯酸酯/聚氨酯三层核壳复合乳液的合成与表征

以自制的聚酯多元醇(PPMBA)、甲苯二异氰酸酯(TDI)、1,6-六亚甲基二异氰酸酯(HDI)、二羟甲基丙酸(DMPA)合成聚氨酯预聚体,再用丙烯酸酯类单体代替有机溶剂对预聚体降黏,封端预聚体后中和分散乳化得包含丙烯酸酯类单体的聚氨酯乳液.向乳液中加入引发剂引发自由基聚合得到复合乳液,最后再加入乙烯基类单体及引发剂合成三层核壳结构的聚丙烯酸酯/聚氨酯复合乳液.研究表明,二异氰酸酯的-NCO与聚酯多元醇中的-OH的物质的量之比(R值)为1.6~4之间时,随R值增加,乳液稳定性增强;DMPA含量在4%~7%的范围内,随DMPA含量的降低,乳胶膜的耐水性提高.通过红外光谱对所合成聚酯多元醇及复合乳液结构进行表征.     

丙烯酸羟乙酯对丙烯酸酯改性水性聚氨酯性能的影响

以异佛尔酮二异氰酸酯、二羟甲基丙酸和聚丙醚二醇等为聚氨酯原料, 丙烯酸丁酯、甲基丙烯酸甲酯、三羟甲基丙烷三丙烯酸酯为丙烯酸酯类单体, 丙烯酸羟乙酯(HEA)为聚氨酯和聚丙烯酸酯间的偶联剂合成了丙烯酸酯改性水性聚氨酯(PU-AC)乳液. 首先建立并验证了一种测定PU接枝率, 即PU与丙烯酸酯发生接枝的部分占PU总数的百分比的方法, 然后探讨了加入HEA后的反应温度和HEA用量对PU接枝率、PU-AC乳胶粒径、胶膜吸水率和交联度等性能的影响. 随着HEA与PU预聚体反应温度和HEA用量的提高, 体系中的最终残余NCO逐渐降低. 当HEA用量低于其加入前体系中残余NCO量时, 增加其用量使PU接枝率和PU-AC乳胶粒径逐渐增加; 当HEA用量大于体系残余的NCO量后继续增加其用量对PU接枝率和PU-AC乳胶粒径的影响不大. 胶膜吸水率随着HEA用量的增加而降低.     

PU-St超浓乳液聚合动力学及聚合物性质的研究

采用一步法制备聚氨酯预聚体 ( PU)苯乙烯 ( St)超浓乳液 ,探讨了稳定的超浓乳液的 NCO/OH和 St/PU最佳比例范围。研究了乳化剂和引发剂浓度对超浓乳液聚合的稳定性及聚合动力学的影响 ,并制得了用 PU改性的聚苯乙烯 ( PS)粉状树脂。测定了乳胶粒子大小、粒径分布、分子量和聚合物膜的动态力学性质。发现乳胶粒子大小及其单分散性随聚合转化率的增加而增加 ;与本体聚合比较 ,聚合物的分子量有明显增大 ;PU- PS复合聚合物具有优良性能。     

胶粒为“Salami”结构的PMMA/SiPUA乳液与膜性能研究

采用两步法,先以六亚甲基二异氰酸酯(HDI)、聚醚二元醇(N210)、端羟丙基硅油(HPMS)、端羟基丙烯酸树脂(PA-OH)为主要原料,合成了含硅聚氨酯-丙烯酸酯(Si PUA)种子乳液,然后在Si PUA乳胶粒内引入甲基丙烯酸甲酯(MMA),通过原位自由基共聚合,构筑了以Si PUA为壳,聚甲基丙烯酸甲酯(PMMA)为多核的"Salami"结构乳胶粒(PMMA/Si PUA).FTIR和DSC测试表明,聚氨酯、有机硅与丙烯酸酯发生反应,并确认了PMMA的生成;TEM结果显示,PMMA/Si PUA乳胶粒子具有"Salami"结构;随着Si PUA中HPMS含量的增加,PMMA/Si PUA乳胶粒子的粒径先增加后减小,粒径分布则从单峰窄分布变化到双峰宽分布,其乳液涂膜的水接触角呈现先增加后减小的趋势,但膜的吸水率则逐渐减小;与Si PUA相比,PMMA/Si PUA涂膜的透明性有一定下降,相分离程度增加;动态流变测试显示,PMMA/Si PUA涂膜中PMMA的存在,提高了其模量和黏度.当Si PUA中HPMS含量为10 wt%,核/壳质量比m(PMMA)/m(Si PUA)=0.5时,PMMA/Si PUA乳液的粒径较小,且为单峰分布,其涂膜的耐水性和耐高温性能较好.     

高固含量低黏度聚氨酯微乳液的制备及性能研究

以聚(四氢呋喃-co-氧化丙烯)二醇(Ng210)为软段,异佛尔酮二异氰酸酯(IPDI)为硬段,以1,2-二羟基-3-丙磺酸钠(DHPS)和二羟甲基丙酸(DMPA)作为亲水扩链剂,采用自乳化法合成了一系列了高固含量低黏度稳定聚氨酯微乳液,分析了DHPS和DMPA质量配比对乳液性能的影响,结果表明,所得乳液粒径呈多元分布,乳胶粒子呈球形;乳液为假塑性流体,表观黏度小于250mPa.s(剪切速率为25s-1)且随切变速率的变化规律呈现一定的切力变稀特征;随着DHPS/DMPA比值的增大,胶粒平均粒径逐渐减小,多分散性增强;当DHPS/DMPA值为4/10～6/10时,乳液中大小粒子粒径比为6～8,且大乳胶粒子的体积分数约为70%～75%,乳液的固含量均大于70%.另外,乳液具有较好的低温和高温以及贮存稳定性,具有较低的表面张力,相对于常规的聚氨酯乳液,所制备的高固含量聚氨酯乳液胶膜具有更好的力学性能.     

端羟基聚丙烯酸酯改性水性聚氨酯

将丙烯酸丁酯(BA)、甲基丙烯酸甲酯(MMA)通过溶液自由基聚合,用巯基乙醇作为链转移剂调控合成了一定分子量的端羟基聚丙烯酸酯(PA),再与聚氨酯(PU)预聚体反应,在水中分散得到PA-PU-PA三嵌段共聚复合乳液。 采用FTIR和¹HNMR测试技术对共聚物结构进行了表征。 结果表明,随着PU与PA质量比的降低,共聚物中丙烯酸酯含量随之增加;PU软硬链段之间的氢键化作用减弱。 TEM显示,复合乳胶粒子形态均匀规整,并呈现明显的核壳结构。改性后的乳胶膜耐水、耐热性能均随着PU/PA质量比的减小而提高,吸水率由25%降低至5%,最大热失重温度由369 ℃提高至432 ℃。     

N-甲基二乙醇胺用量对水性阳-非离子聚氨酯溶液性能的影响

通过预聚体法合成了水性阳-非离子聚氨酯表面活性剂(CPUS),利用红外光谱和核磁共振谱对聚合物的结构和组成进行了表征.并通过动态光散射(DLS)、透射电镜(TEM)、表面张力仪、稳态流变分析及荧光光谱法等系统研究了阳离子亲水扩链剂N-甲基二乙醇胺(MDEA)用量对CPUS表面张力、临界胶束浓度、流变性、胶束的尺寸、微极性和聚集行为的影响.TEM表明,CPUS胶束呈球形核壳结构.随着MDEA含量的增加,CPUS水溶液表面张力和临界胶束浓度(CMC)先减小后增大,其最低值分别为39.54 m N/m和1.99 g/L,胶束的平均粒径和分布系数逐渐减小.当浓度低于CMC时,光散射强度较低且变化缓慢,当浓度高于CMC时,光散射强度呈现逐渐增长趋势,胶束聚集数逐渐增加.随着MDEA含量的增加,乳液黏度增加,胶束间的相互作用增强,假塑行为增强.荧光光谱法表明随CPUS浓度增加,I1/I3值从1.8降低到1.3,I338/I334值从0.5升高到1.7,表明疏水基团聚集形成疏水微区,芘分子从水相极性环境转移到胶束疏水内核.随着MDEA含量的增加,胶束微极性和形成难度先减小后增加.     

PAA/PU合金制备多孔PI薄膜及结构与性能研究

以N,N-二甲基乙酰胺(DMAc)为溶剂, 在聚氨酯(PU)溶液中使均苯四酸二酐(PMDA)与4,4′-二氨基二苯醚(4,4′-ODA)缩聚成聚酰亚胺(PI)预聚体聚酰胺酸(PAA), 从而制成PAA/PU的混合溶液, 然后刮涂成膜, 经过热处理使得PAA亚胺化和PU降解, 制备多孔PI薄膜. 通过对薄膜进行红外光谱,热失重分析及透射电镜(TEM)观察, 结果表明, 最佳的PU热降解温度为360 ℃, PU降解后在PI基体中留下长条状纳米孔, 且孔径大小随聚氨酯含量的增加而增大. 通过对薄膜进行力学性能、 介电性能和吸水率研究, 结果表明, 随着体系中PU用量的增加, 热处理后的多孔PI薄膜的介电常数逐渐下降, 但拉伸强度降低, 吸水率上升.     

甲基丙烯酸正丁酯正相微乳液可控/“活性”光聚合动力学研究

以末端含溴原子的光引发剂2-溴异丁酰氧基-2-甲基-1-苯基甲酮(HMPP-Br)为引发剂,2,2,6,6-四甲基哌啶-1-氧自由基(TEMPO)和2,2,6,6-四甲基哌啶醇(TMP)为调控剂,采用光聚合方法研究了甲基丙烯酸正丁酯(n-BMA)/十二烷基硫酸钠(SDS)/水/正丁醇 O/W型正相微乳液体系的光聚合反应动力学.结果表明,改性后的引发剂具有一定的引发活性,且聚合微乳液体系较稳定,聚合反应获得了良好的ln[M]₀/[M]与时间、数均分子量与转化率之间的线性动力学关系,制备了分子量分布较窄的Poly(n-BMA)均聚物.     

蓖麻油交联改性对室温自愈合聚氨酯性能的影响

以蓖麻油(CTO)或三羟甲基丙烷(TMP)作为交联剂,合成了一系列自愈合聚氨酯弹性体(PU)。借助核磁共振仪和红外光谱仪分析了产物结构,通过电子拉力试验机研究了交联剂添加量对PU的力学性能以及自愈合性能的影响。结果表明:CTO和TMP均能提高PU的拉伸强度,但是断裂伸长率会降低。随着交联剂用量的增加,PU内部交联度提升,自愈合性能下降。当PPG与TMP的物质的量之比为6∶4时,自愈合能力消失。在交联剂用量相同的情况下,CTO交联PU的自愈合性能保留效果比TMP交联PU更好。随着CTO用量的增加,断裂后愈合PU的拉伸强度先增加后减小。当聚丙二醇(PPG)与CTO的物质的量之比为7∶3时,总体性能最佳,在提高样品拉伸强度的同时,其自愈合后的拉伸强度恢复率为80.95%。     

纳米Ni催化剂在超稠油水热裂解降黏中的应用研究

采用甲基环己烷水正辛醇AEO9形成的微乳液体系制备纳米金属Ni催化剂，并利用该催化剂催化辽河超稠油的水热裂解反应。研究结果表明， 280℃时纳米金属Ni能够促进超稠油的水热裂解反应。与原超稠油相比，反应后样品的硫质量分数由0.45%降到0.23%，胶质、沥青质质量分数分别降低了15.83%、15.33%；GC-MS分析结果表明，甲基环己烷在改质过程中能够脱氢生成甲苯；C、H元素分析结果表明，反应后样品中胶质、沥青质的H/C原子比增加，说明从甲基环己烷上脱下的氢能够转移到超稠油中。表面活性剂AEO9、水和油，在改质结束后的降温过程中，形成了稳定的油包水型乳液，起到乳化降黏作用；而添加的甲基环己烷、正辛醇均能起到稀释降黏作用；在上述降黏作用的协同影响下，反应后样品50℃时的黏度由原来的139800mPa·s降至2400mPa·s，由此表明，纳米Ni催化剂对辽河超稠油水热裂解降黏的催化效果显著。     

聚氨酯/苯丙杂化乳液的合成、表征和特性及其在复膜胶中的应用

由聚氨酯(PU)预聚物、丙烯酸丁酯和苯乙烯单体的乳液聚合制备了聚氨酯-苯乙烯-丙烯酸酯(PUSA)杂化乳液,1H NMR显示所得的PU预聚物由烯烃基团封端。 TEM表明,其粒径约为150 nm,且为颜色深浅不同的两部分所组成。 随着PU含量的降低,杂化乳液的热稳定性增加。 DSC分析表明,所得杂化乳液有单一的Tg值,且处于聚氨酯和聚苯丙(PSA)乳液Tg值的中间。 当将得到的杂化乳液用于纸塑和塑塑复合时,其剥离强度分别为14.1 N/2.5 cm和12.2 N/2.5 cm。     

Synthesis of poly(urethane‐imide) using aromatic secondary amine‐blocked polyurethane prepolymer

A set of poly(urethane‐imide)s were prepared using blocked Polyurethane (PU) prepolymer and pyromellitic dianhydride (PMDA). The PU prepolymer was prepared by the reaction of polyether glycol and 2,4‐tolylene diisocyanate, and end capped with N‐methyl aniline. The PU prepolymer was reacted with PMDA until the evolution of carbon dioxide ceased. The effect of tertiary amine catalysts, organo tin catalysts, solvents, and reaction temperature were studied and compared with the poly(urethane‐imide) prepared using phenol‐blocked PU prepolymer. N‐methyl aniline blocked PU prepolymer gave a higher molecular weight poly(urethane‐imide) at a lower reaction temperature in a shorter time. Amine catalysts were found to be more efficient than organo tin catalysts. The reaction was favorable in particular with N‐ethylmorpholine and diazabicyclo(2.2.2)octane (DABCO) as catalysts, and dimethylpropylene urea as a reaction medium. The poly(urethane‐imide)s were characterized by FTIR, GPC, TGA, and DSC analyses. The molecular weight decreased with an increase in reaction temperature. The thermal stability of the PU was found to increase by the introduction of imide component. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 4032–4037, 2000     

Waterborne polyurethanes and their properties

Anionomer-type waterborne polyurethanes (PUs) were obtained from poly(β-methyl-δ-valerolactone) glycol (PMVL) and isophorone diisocyanate, following a prepolymer mixing process. The soft-hard segment phase separation in response to the variations of composition and structure of PU has been studied from the dynamic mechanical measurements of the emulsion cast films. The structural variation included ionic and hard segment content, molecular weight of NCO-terminated prepolymer, and type and length of the soft segment. It was found that phase separation is more sensitive to the soft segment length, rather than the soft segment content. With only phase separation, the rubbery modulus was significant even with lower hard segment content. Phase separation was much more pronounced with PU from poly(tetramethylene adipate) glycol, rather than from PMVL and poly(caprolactone) © 1996 John Wiley & Sons, Inc.     

A novel type of Si-containing poly(urethane-imide)s: synthesis, characterization and electrical properties

A novel type of a Si-containing poly(urethane-imide) (PUI) was prepared by two different methods. In the first method, Si-containing polyurethane (PU) prepolymer having isocyanate end groups was prepared by the reaction of diphenylsilanediol (DSiD) and toluene diisocyanate (TDI). Subsequently the PU prepolymer was reacted with pyromellitic dianhydride (PMDA) or benzophenonetetracarboxylic dianhydride (BTDA) in N-methyl pyrolidone (NMP) to form Si-containing modified polyimide directly. In the second method, PU prepolymer was reacted with diaminodiphenylether (DDE) or diaminodiphenylsulfone (DDS) in order to prepare an amine telechelic PU prepolymer. Finally, the PU prepolymer having diamine end groups was reacted with PMDA or BTDA to form a Si-containing modified polyimide. Cast films prepared by second method were thermally treated at 160 °C to give a series of clear, transparent PUI films. Thermogravimetric analysis indicated that the thermal degradation of PUI starts at 265 °C which is higher than degradation temperature of conventional PU, confirming that the introduction of imide groups improved the thermal stability of PU.To characterize the modified polyimides and their films, TGA, FTIR, SEM and inherent viscosity analyses were carried out. The dielectrical properties were investigated by the frequency-capacitance method. Dielectric constant, dielectric breakdown strength, moisture uptake and solubility properties of the films were also investigated.     

Graft interpenetrating polymer networks of polyurethane and epoxy. II. Toughening mechanism

Graft interpenetrating polymer networks (graft-IPNs) of polyurethane (PU) and the diglycidyl ether of bisphenol A (epoxy) were prepared by first grafting excess PU prepolymer to the epoxy and then simultaneously polymerizing the PU prepolymer and epoxy. The fracture properties, at high shear rate (e.g., impact) and low shear rate (e.g., pseudostatic tensile fracture energy measurement) of these graft-IPNs exhibit opposite behavior. Although dispersed rubber particles can enhance the Izod impact strength, toughening of the matrix of graft-IPNs was found to be the main contribution. In contrast, it was found that a heterogeneous morphology with suitably dispersed rubber domains of appropriate size as well as the toughness of the matrix are requirements for effectively increasing the fracture energy at low shear rate. A reinitiating crack in the plastic matrix is proposed as the main toughening mechanism and can be invoked to interpret the fracture behavior at high and low shear rates of the graft-IPNs.     

Basic structure–property behavior of polyurethane cationomers

Polyurethane (PU) cationomers were synthesized from polytetramethylene adipate glycol (PTAd), isophorone diisocyanate (IPDI), and N-methyl diethanolamine (MDEA) according to a prepolymer mixing process. Basic structure-property behavior of the emulsion (obtained by adding water to the ionomer solution) and emulsion cast film was studied with regard to the molecular weight (M_n) of PTAd, MDEA content, degree of neutralization, and extender functionality. Particle size decreased asymptotically with increasing M_n of PTAd due to the increased chain flexibility, and with the degree of neutralization due to the increased hydrophilicity of the PU. Emulsion viscosity generally showed the opposite tendency with particle size dependence. The major transition temperature, corresponding to the glass transition (T_g) of phase mixed PU or hard segment-rich phase of the PU monotonically increased with MDEA content, degree of neutralization, and with increasing extender functionality. However, with increasing M_n of PTAd, T_g first decreased (M_n = 1000) and then increased (M_n = 1500, 2000), due respectively to the increased hard fraction of phase mixed PU, and soft segment crystallization. Tensile strength increased and elongation at break decreased with MDEA content, degree of neutralization, and extender functionality. © 1994 John Wiley & Sons, Inc.     

Preparations and properties of polyurethane aqueous dispersion from uncatalyzed systems of H12MDI,PTAd/bisphenol A polyol,and DMPA

Aqueous dispersions of polyrethane (PU) containing ionic and nonionic hydrophilic segments were prepared in a prepolymer mixing process using substantial amount of solvent. The acid groups were neutralized with tertiary amine, and chain extension in aqueous media was carried out with triethylene tetramine. Average particle size and particle size distribution of the dispersion, and mechanical and viscoelastic properties of the emulsion cast films were determined.     

Preparation and properties of poly(urethane-imide)s derived from amine-blocked-polyurethane prepolymer and pyromellitic dianhydride

Poly(urethane-imide)s were prepared using amine-blocked-polyurethane (PU) prepolymer and pyromellitic dianhydride. The PU prepolymers were prepared by the reaction of different diols (polypropyleneoxy glycol, polytetramethyleneoxy glycol, polycaprolactonediol and hydroxyl terminated polybutadiene) and different diisocyanates (2,4-tolylene diisocyanate, 1,4-phenelene diisocyanate, 1,6-hexamethylene diisocyanate, isophorone diisocyanate and 4,4^′-methylenebis(cyclohexyl)isocyanate) and end capped with N-methylaniline. The polymerization was faster with aromatic isocyanates than with aliphatic isocyanates. The effect of imide content on the thermal and mechanical properties was studied. The poly(urethane-imide)s were characterized by FTIR, GPC, TGA and for dynamic and static mechanical properties. Weight average molecular weight (M_w) of the polymers did not vary significantly with change in -NCO/-OH ratio where as number average molecular weight (M_n) increased with increasing -NCO/-OH ratio, correspondingly, the dispersity (PD) decreased. Polymers with higher hard segment content exhibited higher glass transition temperature. The thermal stability of the PU was found to increase significantly by the introduction of imide component.