Broadband Er-Yb co-doped superfluorescent fiber source

In this paper, extensive experimental results on broad-band double cladding Er³⁺-Yb³⁺ co-doped superfluorescent fiber sources (SFSs), characterizing their output power, mean wavelength, and bandwidth (BW) stability with variations of pump power, pump wavelength, and fiber temperature, have been reported. For a 55-cm fiber, SFS power from 3.7755 (maximum BW condition of more than 80 nm) to 9.1837 mW (maximum power condition, BW is about 34 nm) has been achieved. The SFS mean wavelength dependence on pump wavelength is highly pump temperature sensitive, and can be reduced to zero in a chosen pump temperature field. The intrinsic variation of the SFS mean wavelength λ_m with fiber temperature is also measured, and a linear variation from 15 to 45 °C with a slop of −0.053 nm/°C for L_f = 100 cm and −0.04 nm/°C for L_f = 55 cm is found.     

Incorporate, switchable dual-wavelength fiber laser with Bragg gratings written in a polarization-maintaining erbium-doped fiber

A stable, incorporate and switchable dual-wavelength fiber laser with two fiber Bragg gratings written in a photosensitive and polarization-maintaining erbium-doped fiber directly, that is, without splices in the laser cavity, is proposed and demonstrated. Simultaneous dual-wavelength oscillation is achieved at room temperature with a wavelength spacing of 0.343 nm. The power fluctuation and wavelength shift of single-wavelength oscillations are measured to be less than 0.24 dB and 0.013 nm over 2 h. The wavelength switchability between single- and dual-wavelength oscillations is realized by altering the voltage upon the electrostrictive ceramic actuator.     

A tunable narrow-line-width multi-wavelength Er-doped fiber laser based on a high birefringence fiber ring mirror and an auto-tracking filter

A novel multi-wavelength erbium-doped fiber laser operating in C-band is proposed and successfully demonstrated. The wavelength interval between the wavelengths is about 0.22 nm. The 3 dB bandwidth of the laser is about 0.012 nm, and the output power reaches 4.8 mW. By using a high birefringence fiber ring mirror (HiBi-FLM) and a tunable FBG, the laser realizes switchable and tunable characteristic. The mode hopping can be effectively prevented. Moreover, this laser can improve wavelength stability significantly by taking advantage of an un-pumped Er³⁺-doped fiber at the standing-wave section. The laser can operate in stable narrow-line-width with single-, dual-wavelength, and unstable triple-wavelength output at room temperature.     

Radiation response behaviour of Al codoped germano-silicate SM fiber at high radiation dose

Radiation response behaviour of Ge + Al doped SM fiber fabricated by the solution doping process has been studied at room temperature with respect to 1310 nm transmission wavelength under three different dose rates of 200, 400 and 600 Rad/min to compare with that of standard Er doped as well as Ge doped SM fibers. Their radiation sensitivity has been observed with variation of dose rates, transmission wavelength along with their recovery nature. Radiation response behaviour of Al doped SM fiber is found to be slightly non-linear in nature with very low dose rate dependency. No saturation level was found upto 13 Krad cumulative dose. Thermobleaching as well as photobleaching phenomena have also been studied. Gamma irradiated Al doped preform shows an absorption peak at around 300 nm due to generation of Al (E′) defect center and gets annihilated after thermobleaching process. Gamma irradiated Al doped SM fiber shows prominent photobleaching effect on their optical attenuation with respect to the 850 nm transmission wavelength. From ESR study resonance signals for Al³⁺ related radiation-induced defect centers are not clearly observed in this study. A very weak hyperfine pattern has been observed for gamma irradiated Al doped preform sample. The high radiation sensitivity along with linear response behaviour, low recovery and almost dose rate independence behaviour of the material system of Ge + Al codoped SM core optical fiber under gamma radiation shows their potential for application as fiber optic radiation sensor in comparison to the universal standard erbium doped SM fiber.     

A broadband ultra flattened chromatic dispersion microstructured fiber for optical communications

A double-cladding microstructured fiber (MF) is proposed in this paper. The inner cladding of this optical fiber is composed of elliptical air holes and silica. The dependence of dispersion on the diameter of the air holes, the pitch, and the axes of the elliptical holes is investigated numerically. The proposed fiber possesses an ultra flattened dispersion curve over a wide wavelength range, and its dispersion value is small. The effective mode area is approaching to 60 μm², and the confinement loss is as low as <0.025 dB/km at 1550 nm. While choosing suitable structure parameters, an ultra dispersion-flattened MF within a broadband from1000 nm to 1900 nm can be achieved. The dispersion fluctuation is 0.6-1.0 ps/(nm·km) in all S, C and L band.     

A novel double-Brillouin-frequency spaced multi-wavelength Brillouin erbium-doped fiber laser based on non-linear amplified fiber loop mirror

In the paper, a ring double-Brillouin-frequency spaced multi-wavelength Brillouin erbium-doped fiber laser based on non-linear amplified fiber loop mirror filter is demonstrated, in which the non-linear amplified fiber loop mirror (AFLMF) is used as a filter. At the 980 nm pump power of 10.29 dBm, the tunable laser source center wavelength of 1563 nm and power of −3 dBm, up to 12 even output channels with 0.16 nm spacing are achieved. At the same time, we study the influence of 980 nm pump power, the polarization controller and the tunable laser source center wavelength on the number of Stokes light wave.     

Numerical design of high nonlinear coefficient of microstructure optical fibers

This paper presents a theoretical design of highly nonlinear microstructure optical fiber with dispersion-flat characteristics. The APSS™ 2.3 software based on the finite difference method with perfectly matched boundary conditions is used to simulate the properties of the proposed microstructure optical fiber. According to simulation, the proposed fiber warrants a high nonlinear coefficient of the order 41 W⁻¹ km⁻¹ and a low dispersion of 0.25 ps/nm/km at 1550 nm wavelength. It assumes a dispersion-flat characteristic of 0 ± 0.50 ps/nm/km in a 1450-1620 nm wavelength range centering 1550 nm wavelength with a modest number of design parameters.     

Generation of dual wavelength ultrashort pulse outputs from a passive mode locked fiber ring laser

By incorporating two sections of polarization maintaining fibers in the passive mode locked fiber ring laser cavity, dual wavelength ultrashort pulse outputs, around 1558 nm and 1570 nm, having the same direction of polarization and pulse widths of 2.4 ps and 2.1 ps, respectively, were observed simultaneously.     

SOA-based actively mode-locked fiber ring laser by forward injecting an external pulse train

An actively mode-locked fiber ring laser based on cross-gain modulation (XGM) in a semiconductor optical amplifier (SOA) is demonstrated to operate stably with a simple configuration. By forward injecting an easily-generated external pulse train, the mode-locked fiber laser can generate an optical-pulse sequence with pulsewidth about 6 ps and average output power about 7.9 mW. The output pulses show an ultra-low RMS jitter about 70.7 fs measured by a RF spectrum analyzer. The use of the proposed forward-injection configuration can realize the repetition-rate tunability from 1 to 15 GHz for the generated optical-pulse sequences. By employing a wavelength-tunable optical band-pass filter in the laser cavity, the operation wavelength of the designed SOA-based actively mode-locked fiber laser can be tuned continuously in a wide span between 1528 and 1565 nm. The parameters of external-injection optical pulses are studied experimentally to optimize the mode-locked fiber laser.     

Determination of nonlinear coefficient and group-velocity-dispersion of bismuth-based high nonlinear optical fiber by four-wave-mixing

Nonlinear coefficient and group-velocity-dispersion of bismuth-based nonlinear fibers were determined by four-wave-mixing measurements. The wavelength dependence of refractive index of bulk bismuth-based glasses was also measured to estimate the material dispersion and waveguide dispersion. A newly developed bi-directional four-wave-mixing configuration enabled us to determine all fiber parameters simultaneously. The obtained fiber nonlinearity γ ∼ 1000 W⁻¹ km⁻¹ of bismuth-based nonlinear fiber is the highest one in the step-index fiber made of oxide glasses as expected from a high refractive index at 1550 nm. Dispersion analysis reveals that the both material dispersion and waveguide dispersion affect to the large group-velocity-dispersion of bismuth-based nonlinear fiber.     

Tunable microwave photonic notch filter using a dual-wavelength fiber laser with phase modulation

A novel tunable microwave photonic notch filter using a phase-modulated dual-wavelength fiber laser is presented. A stable dual-wavelength erbium-doped fiber laser with a linear cavity is formed by a polarization-maintaining uniform fiber Bragg grating (PM-FBG) and a polarization maintaining linearly chirped fiber Bragg grating (PM-LCFBG), both of which were fabricated on a high-birefringence (Hi-Bi) fiber. It is found that a stable room-temperature dual-wavelength operation can be achieved due to the presence of two reflection peaks arising from the orthogonal states of polarization (SOP) of the PM-FBG. Experimental results show stable dual-wavelength lasing operation with a wavelength separation of ∼0.36 nm and a large optical signal-to-noise ratio (OSNR) of over 40 dB under room temperature. The dual-wavelength fiber laser is combined with a phase modulator and a segment of single-mode fiber (SMF) as a dispersive device to form a tunable microwave photonic notch filter. By stretching the PM-FBG to tune the wavelength separation of the dual-wavelength fiber laser, a tunable microwave photonic notch filter with various free spectral ranges (FSRs) and a rejection ratio greater than 35 dB was developed.     

Dual-wavelength high-power Yb-doped double-clad fiber laser based on a few-mode fiber Bragg grating

We report a high-power dual-wavelength Yb-doped double-clad fiber laser based on a few-mode fiber Bragg grating (FMFBG). The FMFBG was fabricated by using a piece of fiber in a length of fiber with a cutoff wavelength of 1225 nm, which supported two modes at 1060 nm. The laser was pumped by a fiber pigtailed laser diode working at 915 nm. Single-wavelength, dual-wavelength and triple-wavelength laser oscillations were observed when the fiber laser operated under different low pump powers. However, stable dual-wavelength operation was achieved at higher pump power of 3.9 W and remained unchanged until the output power reached 5.67 W under the maximum available pump power of 10.7 W. The laser wavelengths were centered at 1059.12 and 1060.80 nm with a full-width at half-maximum of 37 and 43 pm, respectively. The signal-to-noise-ratio was greater than 50 dB and the beam quality factor (M²) was about 1.9.     

Highly reliable strain-tuning of an Erbium-doped fiber laser for the interrogation of multiplexed Bragg grating sensors

The authors implemented a tunable linear cavity Erbium-doped fiber (EDF) laser for the interrogation of multiplexed fiber Bragg grating sensors (BGS). A high-strength single-pulse draw-tower fiber Bragg grating (FBG) was used as the mechanically tunable element enabling the rapid wavelength sweeping of the laser center wavelength. A simple algorithm to process the noisy acquired data and identify the peak of the BGS spectra was employed. For the first time, this type of configuration was used to reliably interrogate at least three fiber Bragg grating sensors with a standard wavelength spacing between the Bragg wavelengths of 3 nm, without risk of breaking the stretched fiber, using an FBG with a simple PZT driven mount as the tuning elements.     

Design and characterization of single mode circular photonic crystal fiber for broadband dispersion compensation

In this paper, we present a single mode circular photonic crystal fiber (C-PCF) for broadband dispersion compensation covering 1400 to 1610 nm wavelength band over the telecommunication windows. Investigations of guiding properties are carried out using finite element method (FEM) with circular perfectly matched layer boundary condition. Numerical study reveals that a negative dispersion coefficient of about −386.57 to −971.44 ps/(nm km) is possible to obtain over the wavelength ranging from 1400 to 1610 nm with a relative dispersion slope (RDS) of about 0.0036 nm⁻¹ at 1550 nm wavelength. In addition, the single mode behaviour of C-PCF is demonstrated by employing V parameter. According to simulation, it is found that the proposed C-PCF acts as a single mode fiber within 1340 to 1640 nm wavelength. Moreover, effective dispersion, relative dispersion slope, birefringence and confinement loss are also presented and discussed.     

Wavelength tunability of L-band fiber ring lasers using mechanically induced long-period fiber gratings

We report on oscillation wavelength control in erbium-doped fiber ring lasers by adjusting the period of a mechanically induced long-period fiber grating (LPFG) inserted into the fiber ring resonator. Pump light is provided by a 974 nm laser diode (LD), the emission of which is coupled into the fiber ring resonator through a wavelength-division multiplexing coupler. Laser oscillation occurs with a threshold pump LD current of 40 mA, corresponding to a threshold pump power of 5 mW. When a periodic pressure of 0.81 N/mm is applied to form the LPFG, the fiber ring laser exhibits the tunable range of 40.9 nm, i.e., from 1563.1 to 1604 nm, by changing the grating period.     

Fabrication of low OH loss holey fibers with varying air hole sizes and their optical properties

We experimentally investigate a flexible fabrication technique for low OH and transmission losses holey fibers with a Ge-doped core and air holes in a silica cladding region. Versatile holey fibers of different size, pitch, and shape of air holes were achieved by controlling the temperature and heating time of the holey fiber preform. In addition, we suppress the OH loss of less than ∼0.323 dB/km at 1383 nm. After fabricating holey fibers, we measure their optical properties including cut-off wavelength, mode field diameter, splicing loss, dispersion, bending loss, and polarization dependent loss based on the size of air holes. The total transmission loss was measured to be ∼0.226 dB/km at 1550 nm by improving the fabrication process. After fabricating optical patch cord based on holey fibers, we measured the long-term stability of the fabricated holey fiber by using the temperature cycling technique for 24 and obtained low power fluctuation of 0.2 dB. We achieve the high quality holey fiber with a low bending loss of ∼0.04 dB/turn under a bending radius of 2.5 mm at 1550 nm. We also obtain a tunable band rejection filter with a number of bending turns.     

Four-wave mixing in dual wavelength fiber laser utilizing SOA for wavelength conversion

In this paper, a novel configuration of a wavelength converter is set forth by utilizing a semiconductor optical amplifier (SOA) as a nonlinear gain medium to generate a four-wave mixing (FWM) effect by using a dual wavelength bi-erbium-doped fiber laser that uses an Arrayed Waveguide Grating (AWG) together with two optical channel selector (OSC) as selective elements to function as a dual wavelength switchable pump power. The four-wave mixing (FWM) is produced with a wavelength detuning of 7 nm from the pump and signal which used is as the converted signal at wavelength 1532.8 nm or 1534.5 nm for transferring data from the input signal at wavelength 1547.0 nm. Thus, even though the conversion efficiency is as low as −43 dB, it is still possible for applications as a wavelength converter.     

Nanosecond laser damage resistance of differently prepared semi-finished parts of optical multimode fibers

Optical multimode fibers are applied in materials processing (e.g. automotive industry), defense, aviation technology, medicine and biotechnology. One challenging task concerning the production of multimode fibers is the enhancement of laser-induced damage thresholds. A higher damage threshold enables a higher transmitted average power at a given fiber diameter or the same power inside a thinner fiber to obtain smaller focus spots.In principle, different material parameters affect the damage threshold. Besides the quality of the preform bulk material itself, the drawing process during the production of the fiber and the preparation of the fiber end surfaces influence the resistance. Therefore, the change of the laser-induced damage threshold of preform materials was investigated in dependence on a varying thermal treatment and preparation procedure.Single and multi-pulse laser-induced damage thresholds of preforms (F300, Heraeus) were measured using a Q-switched Nd:YAG laser at 1064 nm wavelength emitting pulses with a duration of 15 ns, a pulse energy of 12 mJ and a repetition rate of 10 Hz. The temporal and spatial shape of the laser pulses were controlled accurately.Laser-induced damage thresholds in a range from 150 J cm⁻² to 350 J cm⁻² were determined depending on the number of pulses applied to the same spot, the thermal history and the polishing quality of the samples, respectively.     

Switchable triple-wavelength erbium-doped fiber laser using a single fiber Bragg grating in polarization-maintaining fiber

A stable and narrow wavelength spacing multiwavelength erbium-doped fiber laser is proposed and demonstrated. The laser can produce simultaneous dual- and triple-wavelength lasing oscillations with a narrow wavelength spacing of less than 0.1 nm via using a single fiber Bragg gratings written in polarization-maintaining (PM) fiber. By adjusting polarization controller, the wavelength spacing of dual-wavelength lasing oscillations can be tuned to as small as 0.032 nm. The maximum amplitude variation for every lasing wavelength is less than 0.5 dB. The room-temperature operation principle is based on the polarization hole burning and deeply saturated effect in an ordinary erbium-doped fiber ring laser (EDFRL). The laser has the advantages of simple all-fiber configuration, low cost, high stability and operating at room temperature.     

Thermally tunable microfiber knot resonator based erbium-doped fiber laser

A compact and tunable erbium-doped fiber laser is demonstrated using a highly doped fiber and a microfiber knot resonator (MKR) structure which is laid on the surface of a small peltier. The MKR functions as both a reflector and a tunable filter where tunability is achieved by varying the temperature of the resonator by heating the peltier. A stable laser output is achieved at the 1533 nm region with an optical signal to noise ratio (OSNR) of 27 dB using a 65 mW of 980 nm pump power. The operating wavelength of the laser can be tuned from 1532.60 nm to 1533.49 nm as the temperature is increased from the room temperature of 24 to 90 °C. It is observed that the operating wavelength shifts to a longer wavelength as the temperature increases with an efficiency of 12.4 pm/°C. This is due to the thermally induced optical phase shift attributable to the changes in effective refractive index and optical path length of the MKR loop.