Fractal behavior of nanocrystalline ceria-yttria solid solution

The fractal characteristics of nano-sized powders of CeO₂-YO_1.5 solid solutions, prepared by combustion synthesis and calcined at various temperatures, have been investigated by small angle X-ray scattering technique. Results show a mass-fractal behavior for the powders with mass-fractal dimension D_m in the range 2.2-2.6. The estimated particle radii are in the range of 4-15 nm, which is in close agreement with TEM results. For the powders calcined at higher temperatures, the particle interface has a tendency to become rough with a significant growth in the particle size and polydispersity.     

Co-Pt and Fe-Pt bimetallic nanoparticles in a carbon matrix are prepared by a plasma arc process

Nanoparticle ensembles in Co-Pt and Fe-Pt systems embedded in a carbon matrix are prepared by a plasma-arc method. Two-phase samples based on disordered FCC solid solutions are prepared in both systems. In the Co-Pt system, the solid solujtions are mixed within one ensemble; in the Fe-Pt system, they are spatially separated. A magnetization hysteresis curve from Co-Pt nanoparticles (3–12 nm) fully coincides with a magnetization curve from a single-phase disordered solid solution Co_0.50Pt_0.50 (7–9 nm) prepared at 325°C by thermolysis of the precursor double complex salt (DCS). Metal ratios, solid solution structures, and particle sizes being the same, the magnetic response is dictated exclusively by the amount of a magnetic phase of mixed and interacting particles and is independent of the distribution of the magnetic phase over the solid solution phases.     

Analysis of solid solutions stability in scheelite-type molybdates and tungstates

Mutual solubility of bivalent metal molybdates and tungstates with scheelite structure was theoretically estimated by calculating formation enthalpies and the maximal decomposition temperatures of solid solutions at different temperatures. The theoretical stability of continuous solid solutions in binary systems of bivalent metal molybdates and tungstates was found to be higher than reported literature data. After cooling down continuous substitution solid solution should remain in following systems: CaMoО₄–CdMoО₄, SrMoО₄–MMoО₄ (M=Ba, Pb), BaMoО₄–PbMoО₄, SrWO₄–MWO₄ (M=Ca, Pb), and BaWO₄–PbWO₄. There is a probability that at room temperature in systems CaMoО₄–SrMoО_4, CaWO₄–PbWO₄, and BaWO₄–SrWO₄ the single homogeneity region may decompose to limited solid solutions. It was shown experimentally that a continuous series of scheelite-structure solid solutions M_1−xM^I_xТO₄ can be formed via citrate synthesis at temperatures below 500°С.     

A study of the preparation of solid solutions in the system α-Fe2O3Al2O3

In order to elucidate the formation of precipitated iron catalysts for ammonia synthesis, the formation of solid solutions between α-Fe₂O₃ and Al₂O₃ was studied in the temperature range 500–950°C. The Al₂O₃ content in the solid solutions was found to be below 15 mole%. At temperatures of 800–950°C, solid solutions are formed at an appropriate rate. Specimens with relatively large specific surface areas are obtained at 800°C.     

Synthesis processes and transport properties of solid solutions in the Bi<Subscript>2</Subscript>O<Subscript>3</Subscript>-GeO<Subscript>2</Subscript>-V<Subscript>2</Subscript>O<Subscript>5</Subscript> system

The results of studies of solid solutions with the overall composition of Bi₄V_{2 ? x} Ge _x O_{11 ? δ} and Bi₄Ge_{3 ? x} V _x O_{12 + δ} are presented. The process of phase formation are studied during the synthesis of solid solution using the ceramic method and through liquid precursors. Crystallochemical parameters of the obtained compounds are determined. The size distribution of the particles is studied. Conductivity of annealed of polycrystalline samples as a function of temperature and composition is studied using the impedance spectroscopy method. The shape of impedance complex plane plots of the samples obtained in different ways is studied and analyzed.     

三维有序大孔SnO2基固溶体用于有效燃烧碳烟颗粒

柴油车尾气排放的碳烟颗粒对人类的生存环境和身体健康带来了严重危害.催化燃烧是消除碳烟颗粒污染的有效途径.碳烟颗粒催化燃烧是固-固-气相反应,因此催化剂本身具有活泼的氧中心且其能与碳烟颗粒有效接触是提高反应效率的关键因素.为改善碳烟颗粒与催化剂的接触,设计制备三维有序大孔(3DOM)催化剂,使碳烟颗粒可以进入催化剂孔道内部,增加其与催化剂的有效接触,是提高反应活性的有效途径.此外,在催化剂晶格中掺杂其它金属离子形成固溶体结构,可提高其氧化还原性能,也可有效提高其碳烟燃烧活性.SnO2富含活泼的表面缺位氧和可还原的晶格氧,且其熔点高达1630 oC,具有良好的热稳定性,被广泛用于制备气体传感、电化学和催化等材料.在过去的6年中,本课题组在SnO2催化化学领域做了大量系统的工作,将SnO2基催化材料用于多种环保和能源反应.发现通过其它阳离子Fe3+,Cr3+,Ta5+,Ce4+和Nb5+等的掺杂,替换晶格中部分Sn4+形成金红石型SnO2固溶体结构,可显著提高催化剂氧物种的流动性、活性和本身的热稳定性.本文采用胶体晶体模板法制备出了Ce4+,Mn3+和Cu2+离子掺杂的SnO2三维有序大孔固溶体催化剂用于松散接触条件下的碳烟催化燃烧.采用SEM,TEM,XRD,STEM-mapping,O2-TPD和XPS等手段对催化剂进行表征,研究其碳烟催化燃烧性能.SEM和TEM结果表明已成功合成三维有序大孔结构样品.XRD,Raman和STEM-mapping结果表明,Ce4+,Mn3+和Cu2+离子均进入四方金红石型SnO2晶格形成固溶体结构.另外,Raman,H2-TPR,XPS和O2-TPD等结果发现上述离子掺杂三维大孔SnO2后,催化剂表面形成了更活泼、丰富的氧物种,有利于碳烟颗粒燃烧.其中3DOM-Cu1Sn9催化剂具有最丰富的活泼氧中心,因此表现出最高的活性.     

Characterization of solid solutions composed of oxides of Cu,Zn, and Cr for methanol synthesis

Solid solutions of Cu₂O alone and Cu₂O with ZnO or Cr₂O₃ in ZnO · Cr₂O₃ as well as solid solutions of ZnO in Cu₂O · Cr₂O₃ have activities and selectivities for methanol synthesis comparable to solid solutions of Cu₂O in ZnO. Addition of a secondary phase to these solid solutions limits the grain growth and produces higher surface areas.     

Perovskite solid solutions in the BaO-CuO-Y2O3-Nb2O5 system

Freeze dried complex carboxylates are highly reactive precursors for complex perovskite solid solutions in the system BaO-CuO-Y₂O₃-Nb₂O₅ On thermal decomposition of the amorphous precursors the formation of complex crystalline phases begins at 600 °C. In most cases the themodynamically controlled phase composition is reached after a reaction time of two hours at about 900 °C. Beginning from the perovskite compound Ba₂YNbO₆ a partial substitution of Y by Cu or by a combination 2/3 Cu,1/3 Nb leads to extended fields of solid solutions with cubic perovskite structure. Substitution according to Y_0,5xBa₂(Y_1-0,5xCu_xNb)O_6+x is limited to x ≤ 0,4. A compound LBa₂Cu₂NbO₈ (x=2), well characterized for L=La, does not exist for L=Y. The composition of solid solutions depends on the preparation conditions. There are some signs for an inhomogeneous distribution of B-cations in the cubic perovskites.     

XRD and UV-Vis diffuse reflectance analysis of CeO2-ZrO2 solid solutions synthesized by combustion method

A series of ceria-incorporated zirconia (Ce_1−xZr_xO₂,x = 0 to 1) solid solutions were prepared by employing the solution combustion synthesis route. The products were characterized by XRD and UV-Vis-NIR diffuse reflectance spectroscopy. The materials are crystalline in nature and the lattice parameters of the solid solution series follow Vegard’s law. Diffuse reflectance spectra of the solid solutions in the UV region show two intense bands at 250 and 297 nm which are assigned respectively to Ce³⁺ ← O²⁻and Ce⁴⁺ ← O²⁻ charge transfer transitions. The two vibrational bands in 6960 cm⁻¹ and 5168 cm⁻¹ in the NIR region indicate the presence of surface hydroxyl groups on these materials.     

Spectroscopic and electrochemical properties of thin solid films of yttrium bisphthalocyanine

Langmuir—Blodgett (LB) and evaporated thin solid films of the yytrium bisphthalocyanine complex (YPc₂) have been prepared on various substrates. Cyclic voltammograms of films are discussed and the electrochromic effect on LB films is reported. A detailed spectroscopic characterization of the YPc₂ material is given using resonance Raman scattering (RRS), surface-enhanced resonance Raman scattering (SERRS), transmission and reflection absorption FT-IR spectroscopy and UV—vis spectra. The spectroscopic characterization of the chemical and electrochemical oxidations products of YPc₂ films and solutions was carried out by in situ UV—vis spectroscopy. Potential applications are discussed.     

Preparation of Ce-Zr-O solid solution

A single phase solid solution of Ce-Zr-O can be made by using NH₄HCO₃ solution as precipitating agent. The influence of preparation conditions, such as pH, Zr⁴⁺/(CO₃ ^2-+HCO₃ ^-) and Ce³⁺/Zr⁴⁺ ratio on the formation of the solid solution were investigated. The results show that a single phase Ce-Zr-O solid solution can be formed only under a narrow window of preparation conditions, indicating that some compounds are formed in the precipitating process. The compound may contain Ce³⁺, Zr⁴⁺, CO₃ ^2-, HCO^3-, and OH^-. The solid solution so prepared can be described as Ce_0.37Zr_0.63O₂. This revised version was published online in August 2006 with corrections to the Cover Date.     

Direct synthesis and applications of solid silylzinc reagents

The increased synthetic utility of organosilanes has motivated researchers to develop milder and more practical synthetic methods. Silylzinc reagents, which are typically the most functional group tolerant, are notoriously difficult to synthesize because they are obtained by a pyrophoric reaction of silyllithium, particularly Me₃SiLi which is itself prepared by the reaction of MeLi and disilane. Furthermore, the dissolved LiCl in silylzinc may have a detrimental effect. A synthetic method that can avoid silyllithium and involves a direct synthesis of silylzinc reagents from silyl halides is arguably the simplest and most economical strategy. We describe, for the first time, the direct synthesis of PhMe₂SiZnI and Me₃SiZnI reagents by employing a coordinating TMEDA ligand, as well as single crystal XRD structures. Importantly, they can be obtained as solids and stored for longer periods at 4 °C. We also demonstrate their significance in cross-coupling of various free alkyl/aryl/alkenyl carboxylic acids with broader functional group tolerance and API derivatives. The general applicability and efficiency of solid Me₃SiZnI are shown in a wide variety of reactions including alkylation, arylation, allylation, 1,4-addition, acylation and more.

The first direct synthesis of PhMe₂SiZnI and Me₃SiZnI reagents from silyl iodides is described. They can be obtained as solids and stored at 4 °C for extended periods. The versatility of solid Me₃SiZnI is demonstrated in a variety of reactions.     

On the solid solution of the spinel phase in the system NiO-Al2O3

The solid solubility of Al₂O₃ in NiAl₂O₄ spinel has been investigated by powder X-ray diffraction of samples prepared by solid state synthesis. The solid solution region found was in agreement with a previous report. The cubic cell parameter of the spinel solid solution was observed to decrease with increasing alumina content. Spinel with high alumina content was shown to be close to an inverse spinel as previously reported for stoichiometric NiAl₂O₄ and the inversion parameter proved to be relatively independent of the overall composition.     

Highly-loaded amphiphilic polyimino resin: quench reagent and solid support for peptide synthesis

We demonstrate herein that polyimino resin 4a prepared by condensation of α,α′-dichloro-p-xylene, ethylenediamine and tris-(2-aminoethyl)-amine can be successfully exploited as a quench reagent for acids and electrophiles both in aqueous and organic solutions. Scope and limitations of such a resin as a solid support for peptide synthesis were also investigated.     

Greener solid state synthesis of a ternary lanthanum complex at room temperature

Wet chemical synthesis of rare-earth complexes often requires large amounts of solvents to dissolve reactants, and the use of base to neutralize acidic solution. We have explored a green alternative route that involves solid-state synthesis of ternary lanthanum complex at room temperature by using lanthanum chloride hydrate (LaCl_3?·?6H₂O), sodium p-hydroxybenzoate (PBA), and 8-hydroxyquinoline (8-hq). The structure and composition of the ternary lanthanum complex were confirmed by microanalysis, Fourier transform infrared (FT-IR), UV-Vis, X-ray diffraction (XRD), electron diffraction, and thermogravimetric analysis. UV-Vis and FT-IR spectra confirms coordination of lanthanum ion with two ligands and XRD results show that signals of the product are not from the three reactants, and are believed to originate from the ternary lanthanum complex prepared by solid-state reaction. Effects of reaction conditions such as molar ratios and synthetic method on the formation of ternary lanthanum complex were also investigated. The structure and composition of the ternary lanthanum complex are independent of molar ratios of reactants. Compared to the ternary lanthanum complex prepared via solution-phase synthesis, although the ternary lanthanum complex prepared by solid-state reactions has the same composition and structure, the synthesis is scalable and greener.     

Green and rapid synthesis of dihydropyrimido [4,5‐b]quinolinetrione derivatives using CoFe2O4@PPA as high efficient solid acidic catalyst under ultrasonic irradiation

A new high efficient and green protocol for the preparation of dihydropyrimido[4,5‐b]quinolinetrione derivatives using magnetically solid acid catalyst was presented. High performance solid acid catalyst was prepared through a three‐step reaction. Firstly, CoFe₂O₄ nano particles were synthesized using co‐precipitation method. In second step, CoFe₂O₄ nano particles were coated with SiO₂ shell through treatment with tetraethyl orthosilicate (CoFe₂O₄@SiO₂). Finaly, CoFe₂O₄@SiO₂ was modified with polyphosphoric acid (CoFe₂O₄@SiO₂/PPA) in a simple manner. Green reusable catalyst was characterized in details using FTIR, VSM, TEM, FESEM, EDX and used as catalyst for the synthesis of dihydropyrimido[4,5‐b]quinolinetrione derivatives. Reaction was performed under ultrasonic irradiation as green, effective and mild conditions and products were achieved in high to excellent yields. Green and eco‐friendly conditions, short reaction times with high yield of products in addition to easy workup are some merits of presented method.     

Exploring the structural,mechanical and thermodynamic properties of Ti-V solid solutions

Although Ti-V based high-temperature alloys are used in aerospace engine, rocket engine and hot sections, the structure and mechanical properties of Ti-V alloys remains controversy. To explore the correlation between structural and mechanical properties, we apply employed the DFT method to study the phases stability, mechanical and thermodynamic properties of Ti-V solid solution. Two Ti-V solid solutions: Ti(V)_ss solid solution and V(Ti)_ss solid solution are discussed. Two Ti-V solid solutions are thermodynamic stability. In particular, the Ti-V solid solution prefers to form V(Ti)_ss solid solution, in while the V(Ti)_ss solid solution remains cubic structure. Furthermore, the Ti(V)_ss solid solution is a mechanical instability. However, the V(Ti)_ss solid solution is a mechanical stability. Here, the bulk modulus, shear modulus and Young's modulus of V(Ti)_ss solid solution are 136.9, 23.5 and 66.7 GPa. In particular, the bulk modulus of V(Ti)_ss solid solution is higher than the bulk modulus of the pure Ti. In addition, the V(Ti)_ss solid solution shows better ductility compared to the pure Ti and V. Naturally, the stability and mechanical properties of V(Ti) solid solution is related to the Ti-V metallic bond because of the localized hybridization between the Ti(3d) and V(3d).     

Phase transformation and structure of n-C50H102/n-C60H122 solid solutions formed from the vapor phase

Binary solid solutions of n-paraffins (n-C₅₀H₁₀₂/n-C₆₀H₁₂₂) epitaxially prepared on potassium hydrogen phthalate substrate from the vapor phase have been studied by electron diffraction to characterize their phase transitions and structure. The continuity of solid solution in the n-C₅₀H₁₀₂/n-C₆₀H₁₂₂ system is demonstrated once lamellar ordering of the crystal packing is achieved. However, such ordering is achieved only by annealing and proceeds through a series of intermediate chain packings. At first, the electron diffraction patterns from all samples prepared at room temperature resemble those from polyethylene, in which no spots corresponding to the interlayer spacings appear. Longitudinal chain translations are induced by annealing to cause the lamellar reflections to appear, while the “polyethylene” subcell reflections remain unsplit until the crystal structure with well-defined methyl end planes is reached.     

The sol–gel synthesis of perovskites by an EDTA/citrate complexing method involves nanoscale solid state reactions

Nowadays, sol–gel procedures are well established in the synthesis of complex oxides as they allow to obtain phase pure products and to control precisely their stoichiometry. This quality makes them a tool of choice for the preparation of perovskite-type oxides. To optimize the functional properties of these materials, it is essential to set accurately their possible complex stoichiometries. However, details of the formation of the perovskite crystal remain obscure. Different stages of an ethylene-diamine-tetraacetic acid (EDTA)/citrate-gel based synthesis process for mixed conducting (Ba_0.5Sr_0.5)(Fe_0.8Zn_0.2)O_3−δ of cubic perovskite structure are elucidated. The combination of analytical transmission electron microscopy with X-ray diffraction reveals that the perovskite-type oxide is formed already at moderate temperatures at around 700 °C via nanoscale solid state reactions between finely-dispersed crystalline intermediates identified as a spinel and a carbonate. The reaction scheme, however, is intricate and includes stuffed tridymite structures as transient phases. The ultrafine intermixing of extremely small reactants makes EDTA/citrate-gel based procedures superior to classical solid state routes with respect to applications that demand phase purity and stoichiometry control.     

Co-Pt bimetallic catalysts for the selective oxidation of carbon monoxide in hydrogen-containing mixtures

The performance of a Co-Pt powder and of Co-Pt catalysts supported on γ-Al₂O₃ and on the graphite-like carbon material Sibunit in selective CO oxidation in hydrogen-containing mixtures is considered. Fine particles of metal-metal solid solutions and intermetallides were obtained by the decomposition of a Co- and Pt-containing double complex salt in a hydrogen atmosphere at ～400°C. As compared to their Pt and Co monometallic counterparts, the bimetallic catalysts are more active and allow the CO concentration in hydrogen-containing mixtures to be reduced from 1 to 10^?3 vol %. This effect is likely due to the formation of bimetallic particles of a Co-Pt solid solution on the support surface.