石墨烯/硫酸铅复合材料的制备及其在铅酸电池中的电化学性能

利用简单的浸渍法制备了石墨烯/硫酸铅复合材料,使得硫酸铅可以直接用作铅酸电池负极材料。该复合材料分别以100 mA·g^-1、200 mA·g^-1和300 mA·g^-1电流密度放电时,平均放电比容量分别可达到110、94和69 mAh·g^-1,而硫酸铅仅为49、5和0.5 mAh·g^-1,显示出复合材料在高倍率充放电下更好的比容量和再接受充电能力。循环伏安测试表明石墨烯的电容效应随扫描速率增大而增强,同时析氢也变得严重,使得复合材料在充放电过程中充电效率比纯硫酸铅低20%。在充放电过程中,石墨烯能够提高硫酸铅1倍以上的放电容量,并将充电电压提高0.1 V。XRD和SEM结果显示硫酸铅均匀分布在石墨烯片层上,没有出现团聚现象。     

石墨烯/硫酸铅复合材料的制备及其在铅酸电池中的电化学性能

利用简单的浸渍法制备了石墨烯/硫酸铅复合材料,使得硫酸铅可以直接用作铅酸电池负极材料。该复合材料分别以100 mA.g-1、200 mA.g-1和300 mA.g-1电流密度放电时,平均放电比容量分别可达到110、94和69 mAh.g-1,而硫酸铅仅为49、5和0.5 mAh.g-1,显示出复合材料在高倍率充放电下更好的比容量和再接受充电能力。循环伏安测试表明石墨烯的电容效应随扫描速率增大而增强,同时析氢也变得严重,使得复合材料在充放电过程中充电效率比纯硫酸铅低20%。在充放电过程中,石墨烯能够提高硫酸铅1倍以上的放电容量,并将充电电压提高0.1 V。XRD和SEM结果显示硫酸铅均匀分布在石墨烯片层上,没有出现团聚现象。     

电弧放电法制备石墨烯的硝酸改性及其电化学性能增强

采用电弧放电法大规模制备了层数少, 导电率高, 结晶性好的石墨烯纳米片(GNSs). 通过扫描电镜(SEM)和透射电镜(TEM)表征发现制得的石墨烯形貌良好. 然而电化学测试表明GNSs作为电极材料的电容性能不好. 为了增加材料表面电化学反应活性点, 促进GNSs在水系电解液中的润湿性, 我们对所制备的GNSs表面进行了硝酸改性处理. 结果显示硝酸处理后的石墨烯纳米片(H-GNSs)表面新增了较多的含氧氮官能团,其亲水性得到了显著提高. 对H-GNSs的电化学研究表明: 硝酸改性处理后的GNSs在2 mol·L^-1 KOH溶液中电流密度为0.5 A·g^-1时, 比电容可达65.5 F·g^-1, 约为改性前的30 倍; 此外, H-GNSs作为电极材料连续进行2000次充放电测试后还展示出了良好的循环稳定性, 是一种潜在的超级电容器电极材料.     

Hydrothermal synthesis of reduced graphene sheets/Fe2O3 nanorods composites and their enhanced electrochemical performance for supercapacitors

Reduced graphene nanosheets/Fe₂O₃ nanorods (GNS/Fe₂O₃) composite has been fabricated by a hydrothermal route for supercapacitor electrode materials. The obtained GNS/Fe₂O₃ composite formed a uniform structure with the Fe₂O₃ nanorods grew on the graphene surface and/or filled between the graphene sheets. The electrochemical performances of the GNS/Fe₂O₃ hybrid supercapacitor were tested by cyclic voltammetry, electrochemical impedance spectroscopy, and galvanostatic charge–discharge tests in 6 M KOH electrolyte. Comparing with the pure Fe₂O₃ electrode, GNS/Fe₂O₃ composite electrode exhibits an enhanced specific capacitance of 320 F g⁻¹ at 10 mA cm⁻² and an excellent cycle-ability with capacity retention of about 97% after 500 cycles. The simple and cost-effective preparation technique of this composite with good capacitive behavior encourages its potential commercial application.     

Preparation and electrochemical analysis of graphene/polyaniline composites prepared by aniline polymerization

Polyaniline (PANI)/graphene nanosheet (GNS) composites were prepared by a chemical oxidation polymerization. The morphology, structure, and crystallinity of the composites were examined by scanning electron microscopy, transition electron microscopy, and X-ray diffraction. Electrochemical properties were characterized by cyclic voltammetry in 1 M H₂SO₄ electrolyte. GNS are considered as supporting materials which can provide a large number of active sites. The PANI nanofibers with diameter of 50 nm were homogeneously coated on the surface of GNS. The PANI/GNS composites exhibited a better electrochemical performance than the pure individual components. The PANI/GNS composites showed the highest specific capacitance 923 Fg^?1 at 10 mVs^?1 compared to 465 Fg^?1 for pure PANI and 99 Fg^?1 for GNS.     

石墨烯/钴镍双氢氧化物复合材料的制备及其超电容特性

采用氧化石墨(GO)还原法制备石墨烯(GNS),以氨水为沉淀剂,在石墨烯存在的情况下,通过Co²⁺和Ni²⁺化学共沉积的方法合成了石墨烯/钴镍双氢氧化物复合电极材料,采用红外光谱(FT-IR)、X射线衍射(XRD)、场发射扫描电子显微镜(FE-SEM)、比表面积测试(BET)等技术手段表征了产物的组成、结构和形貌,用循环伏安、恒电流充放电等测试方法对复合材料的电化学性能进行了研究。 研究发现,石墨烯纳米片均匀分散在钴镍双氢氧化物中,改善了钴镍双氢氧化物的传导性和结构稳定性。 电化学测试表明,在1 A/g的电流密度下,复合材料比电容高达2770 F/g,且循环500次后,比电容仍能保持93.4%,呈示该复合材料具有优异的电化学性能。     

石墨烯负载新型π-共轭聚合物纳米复合电极材料的合成及其超级电容特性

采用γ射线辐照还原技术获得易分散石墨烯(GNS),并以其为载体,以樟脑磺酸为掺杂剂和软模板,借助化学氧化聚合方法制备出分级孔结构的石墨烯负载聚(1, 5-二氨基蒽醌)(GNS@PDAA)纳米复合材料。运用傅里叶变换红外(FTIR)光谱、拉曼光谱(Raman)、原子力显微镜(AFM)、能谱仪(EDS)、场发射扫描电镜(FE-SEM)和电化学测试等手段研究了不同GNS/DAA质量比对GNS@PDAA复合材料的形貌、结构及超级电容特性的影响。研究表明,当DAA/GNS质量比为6/1时,借助π-π堆叠和网络限域作用, PDAA以20-40 nm纳米颗粒的形式牢固沉积于石墨烯表面,材料内部存在大量10-30 nm尺寸的介孔。该GNS@PDAA复合材料在0.5 A·g^-1时呈现最高的比电容(398.7 F·g^-1),优异的倍率特性(在50 A·g^-1下比电容保持率为71%)和非常好的循环性能(20000次循环后比电容损失仅为8.3%)。进而证实了GNS@PDAA复合材料所组装的超级电容器具有优异的串并联特性。     

A Co(OH)2−graphene nanosheets composite as a high performance anode material for rechargeable lithium batteries

A Co(OH)₂?graphene nanosheets (Co(OH)₂?GNS) composite as a high performance anode material was firstly prepared through a simultaneous hydrothermal method. The structure, morphology and electrochemical performance of the obtained samples were systematically investigated by X-ray diffraction (XRD), transmission electron microscope (TEM) and electrochemical measurements. According to the TEM analysis, the surface of the Co(OH)₂ is surrounded with GNS in the Co(OH)₂?GNS composite. The specific discharge (lithiation) and charge (delithiation) capacities of Co(OH)₂?GNS attain to 1599 and 1120 mAh/g at a current density of 200 mA/g in the first cycle, respectively. After 30 cycles, the reversible capacity of Co(OH)₂?GNS is still 910 mAh/g with the retention of 82%. The particular structure of Co(OH)₂ particles surrounded by the GNS could limit the volume change during cycling and provide an excellent electronic conduction pathway, which could be the main reason for the remarkable improvement of electrochemical performance.     

Three-layer structure graphene/mesoporous silica composites incorporated with C8-modified interior pore-walls for residue analysis of glucocorticoids in milk by liquid chromatography–tandem mass spectrometry

Three-layer structure graphene/mesoporous silica composites incorporated with C8-modified interior pore-walls (graphene@mSiO₂-C8) were prepared and applied for efficient extraction of glucocorticoid residuals in milk followed by liquid chromatography-tandem mass spectrometry (LC–MS/MS) analysis. The graphene@mSiO₂-C8 nanocomposites were synthesized by coating C8-modified mesoporous silica onto hydrophilic graphene nanosheets through a simple surfactant-mediated co-condensation sol–gel process. The obtained nanosheets possess unique properties of large surface area (632 m²/g), extended plate-like morphology in the exterior surface, highly open pore structure with uniform pore size (2.8 nm), numerous C8-modified interior pore-walls, as well as good water dispersibility. The performance of the prepared graphene@mSiO₂-C8 materials for extracting small hydrophobic molecules directly from complex protein-rich samples was evaluated by analysis of glucocorticoids in milk. Extraction conditions such as sorbents amount, type and volume of eluting solvent, time of adsorption and desorption were investigated and optimized to achieve the best efficiency. Method validations including linearity, recovery, repeatability, and limit of detection (LOD) were also studied. The results indicated that this methodology provided low LOD (S/N = 3, 0.0075–0.03 ng mL⁻¹) and good linearity (0.03–60 ng mL⁻¹, R² > 0.996) for glucocorticoids. Satisfactory reusability and stability were also obtained during the extraction. Finally, the graphene@mSiO₂-C8 composites were successfully applied to the extraction and residue analysis of glucocorticoids in real milk samples. The experimental results showed that this novel approach offered an attractive choice for convenient, efficient and rapid solid-phase extraction of targeted hydrophobic compounds in biological samples.     

石墨烯包覆天然球形石墨作为锂离子电池的负极材料，是否需要乙炔黑导电剂？

我们通过包覆炭化的方法制备得到了石墨烯包覆的天然球形石墨(G/SG)材料,并使用扫描电子显微镜、X射线衍射仪以及多种电化学测试手段考察了不同石墨烯含量的复合材料的形貌结构及电化学性能。我们发现,在不添加乙炔黑(AB)的情况下,G/SG复合材料表现出较高的首次库伦效率,很好的循环稳定性和高倍率性能。当石墨烯包覆量为1%时,材料50次循环后的可逆容量可与添加10%AB的天然石墨电极(SG)等同;当石墨烯包覆量为2.5%时,材料的比容量完全高于添加10%AB的石墨电极。材料电化学性能的改善归因于石墨烯的包覆。一方面,石墨烯的柔软可变性可以保证天然石墨颗粒在充放电过程中的结构完整性,从而有效改善材料的循环稳定性;另一方面,石墨烯的存在提高了电极的导电性,促进更好导电网络的形成。因此,石墨烯包覆天然球形石墨材料中,石墨烯不仅是活性物质,也发挥导电剂的作用。当添加5%的乙炔黑时,在50 mA·g^-1电流循环50次后,5%G/SG电极的可逆容量从381.1 mAh·g^-1提高到404.5 mAh·g^-1,在1 A·g^-1电流时可逆容量从82.5 mAh·g^-1提高到101.9 mAh·g^-1,这表明G/SG电极仍然需要乙炔黑导电剂。乙炔黑颗粒填充在复合材料的空隙中,通过点接触的形式连接到G/SG颗粒,与石墨烯协同作用形成了更加有效的导电网络。尽管石墨烯包覆和乙炔黑添加对天然石墨电极具有积极的影响,例如增加了天然石墨电极的导电性和储锂性能(包括可逆容量,倍率性能和循环性能),但随着石墨烯或乙炔黑的增加,电极密度通常会降低。因此,在实际应用中应考虑石墨负极材料的质量和体积容量的平衡。这些结果对天然石墨的进一步商业应用具有重要意义。我们的工作为天然石墨电极在锂电池中的电化学行为提供了一种新的认识,并且有助于制备更高性能的负极材料。     

A novel non-enzymatic glucose sensor based on Cu nanoparticle modified graphene sheets electrode

A novel, stable and sensitive non-enzymatic glucose sensor was developed by potentiostatically electrodepositing metallic Cu nanoparticles on graphene sheets. The electrochemical performance of the Cu-graphene sheets electrode for detection of glucose was investigated by cyclic voltammetry and chronamperometry. The Cu-graphene sheets electrode displayed a synergistic effect of copper nanoparticles and graphene sheets towards the oxidation of glucose in alkaline solution, showing higher oxidation current and negative shift in peak potential. At detection potential of 500 mV, the Cu-graphene electrode sensor presented a wide linear range up to 4.5 mM glucose with a detection limit of 0.5 μM (signal/noise = 3). In addition, the sensor responds very quickly (<2 s) with addition of glucose. Furthermore, the Cu-graphene sheets electrode exhibits high stability and selectivity to glucose, and the poisoning by chloride ion as well as interference from the oxidation of common interfering species (ascorbic, dopamine, uric acid and carbohydrate) are effectively avoided. The Cu-graphene sheets electrode allows highly selective and sensitive, stable and fast amperometric sensing of glucose, which is promising for the development of non-enzymatic glucose sensor.     

Graphene supported Sn–Sb@carbon core-shell particles as a superior anode for lithium ion batteries

This paper reports the preparation and Li-storage properties of graphene nanosheets(GNS), GNS supported Sn–Sb@carbon (50–150 nm) and Sn–Sb nanoparticles (5–10 nm). The best cycling performance and excellent high rate capabilities were observed for GNS-supported Sn–Sb@carbon core-shell particles, which exhibited initial capacities of 978, 850 and 668 mAh/g respectively at 0.1C, 2C and 5C (1C = 800 mA/g) with good cyclability. Besides the GNS support, the carbon skin around Sn–Sb particles is believed to be a key factor to improve electrochemical properties of Sn–Sb.     

Ni-based nanocomposites supported on graphene nano sheet (GNS) for supercapacitor applications

The Ni-based/graphene nano sheet (GNS) materials have been prepared by using the polyol reduction process and the NiO dispersed layer was fabricated on Ni metal to form the core/shell nanocomposites. These Ni-based/GNS composite materials possess excellent electrochemical properties, and have been investigated by thermal gravimetric analysis, X-ray diffraction, transmission electron microscopy and field emission scanning electron microscopy techniques. The electrochemical performance was measured by cyclic voltammograms and galvanostatic charge/discharge tests in 1 M KOH electrolyte solution. The results show that the 60Ni-250 sample has the potential application in supercapacitors because of its good electrochemical properties.     

Facile synthesis of graphene-supported shuttle- and urchin-like CuO for high and fast Li-ion storage

Graphene nanosheet (GNS) supported shuttle- and urchin-like CuO nanostructures are prepared by a facile low-temperature solution route. CuO nanoshuttles or urchin-like nanostructures are dispersed uniformly on GNS, forming a three dimensional CuO-GNS layer-by-layer network after stacking. When fabricated as anode materials for lithium-ion batteries, CuO-GNS composites exhibit superior Li-ion storage properties in terms of high capacity, long cycle life, and excellent rate performance. At a large current of 700 mA/g, GNS-supported CuO nanoshuttles show a higher-than-theoretical capacity of 826 mAh/g after 100 cycles, which is even larger than the reversible capacity of 771 mAh/g achieved at 70 mA/g after 40 cycles.     

Nanocrystalline tin compounds/graphene nanocomposite electrodes as anode for lithium-ion battery

Nanocrystalline tin (Sn) compounds such as SnO₂, SnS₂, SnS, and graphene nanocomposites were prepared using hydrothermal method. The X-ray diffraction (XRD) pattern of the prepared nanocomposite reveals the presence of tetragonal SnO₂, hexagonal SnS₂, and orthorhombic SnS crystalline structure in the SnO₂/graphene nanosheets (GNS), SnS₂/GNS, and SnS/GNS nanocomposites, respectively. Raman spectroscopic studies of the nanocomposites confirm the existence of graphene in the nanocomposites. The transmission electron microscopy (TEM) images of the nanocomposites revealed the formation of homogeneous nanocrystalline SnO₂, SnS_2, and SnS particle. The weight ratio of graphene and Sn compound in the nanocomposite was estimated using thermogravimetric (TG) analysis. The cyclic voltammetry experiment shows the irreversible formation of Li₂O and Li₂S, and reversible lithium-ion (Li-ion) storage in Sn and GNS. The charge–discharge profile of the nanocomposite electrodes indicates the high capacity for the Li-ion storage, and the cycling study indicates the fast capacity fading due to the poor electrical conductivity of the nanocomposite electrodes. Hence, the ratio of Sn compounds (SnO₂) and GNS have been altered. Among the examined SnO₂:GNS nanocomposites ratios (35:65, 50:50, and 80:20), the nanocomposite 50:50wt% shows high Li-ion storage capacity (400 mAh/g after 25 cycles) and good cyclability. Thus, it is necessary to modify GNS and Sn compound composition in the nanocomposite to achieve good cyclability.     

Activated carbon/graphene composites with high-rate performance as electrode materials for electrochemical capacitors

Glucose-derived activated carbon (GAC)/reduced graphene oxide (RGO) composites are prepared by pre-carbonization of the precursors (aqueous mixture of glucose and graphene oxide) and KOH activation of the pyrolysis products. The effect of the mass ratio of graphene oxide (GO) in the precursor on the electrochemical performance of GAC/RGO composites as electrode materials for electrochemical capacitors is investigated. It is found that the thermally reduced graphene oxide sheets serves as a wrinkled carrier to support the activated carbon particles after activation. The pore size distribution and surface area are depended on the mass ratio of GO. Besides, the rate capability of GAC is improved by the introduction of GO in the precursor. The highest specific capacitance of 334 F g^?1 is achieved for the GAC/RGO composite prepared from the precursor with a GO mass ratio of 3 %.     

Bio-electrocatalysis of NADH and ethanol based on graphene sheets modified electrodes

Characterization and application of graphene sheets modified glassy carbon electrodes (graphene/GC) have been presented for the electrochemical bio-sensing. A probe molecule, potassium ferricyanide is employed to study the electrochemical response at the graphene/GC electrode, which shows better electron transfer than graphite modified (graphite/GC) and bare glassy carbon (GC) electrodes. Based on the highly enhanced electrochemical activity of NADH, alcohol dehydrogenase (ADH) is immobilized on the graphene modified electrode and displays a more desirable analytical performance in the detection of ethanol, compared with graphite/GC or GC based bio-electrodes. It also exhibits good performance of ethanol detection in the real samples. From the results of electrochemical investigation, graphene sheets with a favorable electrochemical activity could be an advanced carbon electrode materials for the design of electrochemical sensors and biosensors.     

Controlled synthesis of MnSn(OH)6/graphene nanocomposites and their electrochemical properties as capacitive materials

We report the synthesis of novel MnSn(OH)₆/graphene nanocomposites produced by a co-precipitation method and their potential application for electrochemical energy storage. The hydroxide decorated graphene nanocomposites display better performance over pure MnSn(OH)₆ nanoparticles because the graphene sheets act as conductive bridges improving the ionic and electronic transport. The crystallinity of MnSn(OH)₆ nanoparticles deposited on the surface of graphene sheets also impacts the capacitive properties as electrodes. The maximum capacitance of 31.2 F/g (59.4 F/g based on the mass of MnSn(OH)₆ nanoparticles) was achieved for the sample with a low degree of crystallinity. No significant degradation of capacitance occurred after 500 cycles at a current density of 1.5 A/g in 1 M Na₂SO₄ aqueous solution, indicating an excellent electrochemical stability. The results serve as an example demonstrating the potential of integrating highly conductive graphene networks into binary metal hydroxide in improving the performance of active electrode materials for electrochemical energy storage applications.     

Sensitive detection of biomolecules and DNA bases based on graphene nanosheets

High surface area electrode materials are of interest for the application of electrochemical sensors. Currently, chemical vapor deposition (CVD) graphene-sensing electrodes are scarce. Herein, for the first time, a graphene based on a Ta wire support was prepared using the CVD method to form a highly electroactive biosensing platform. Scanning electron microscopy (SEM), transmission electron microscopy (TEM), electrochemical impedance spectroscopy (EIS), cyclic voltammetry (CV), and differential pulse voltammetry (DPV) were utilized to characterize the morphology and investigate the electrochemical properties of the CVD graphene electrodes. The resulting CVD graphene electrode exhibited good electrocatalytic activity and had a prominent response effect on dopamine, uric acid, guanine, and adenine. Standing graphene nanosheets have rich catalytic sites such as the edges, the defect levels of the plane, and porous network structures between the graphene nanosheets. These catalytic sites prompt the adsorption and resolution for the four species and the strong electron transport capability of the CVD graphene, which effectively improved the electrical signals for response to four species. Moreover, the graphene electrode is a promising candidate in electrochemical sensing and other electrochemical device applications.     

Graphene enhanced electrochemiluminescence of CdS nanocrystal for H2O2 sensing

Graphene-CdS (G-CdS) nanocomposites were successfully prepared by CdS nanocrystals (CdS NCs) formed in situ on the surface of graphene sheets, using graphene oxide (GO) sheets with rich negatively charged carboxylic acid groups as starting materials. Compared with pure CdS NCs, the presence of the graphene doped in G-CdS nanocomposites could facilitate the electrochemical redox process of CdS NCs; further, the as-prepared G-CdS nanocomposite can react with H₂O₂ to generate strong and stable electrochemiluminescent (ECL) emission, which not only enhances its ECL intensity by about 4.3-fold but also decreases its onset potential for about 320 mV. The as-prepared solid-state ECL H₂O₂ sensor shows acceptable linear response from 5 μM up to 1 mM with a detection limit of 1.7 μM (S/N = 3). The ECL H₂O₂ sensor exhibits excellent reproducibility and long-term stability. Such a property would promote the potential application of the graphene as enhanced materials in fabricating sensors for chemical and biochemical analysis.